Search NASA⌕ Search

SEARCH · Search NASA

Results for “Composite cathode”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Degradation & Performance Studies of ALD-Stabilized Nano-Composite SOFC Cathodes

This work showed, definitively, for the first time, that zirconia Atomic Layer Deposited (ALD) overcoats improve the stability of Solid Oxide Fuel Cell (SOFC) cathodes by chemically gettering interfacial Sr that has segregated out of lanthanum strontium cobalt iron oxide (LSCF). The optimum ALD ZrO 2 overcoat thickness was found to be ≥5 nm and <10 nm. Gadolinium doped ceria (GDC) pre-infiltration was also shown, for the first time, to improve SOFC cathode stability through the chemical getting of Sr at the LSCF-backbone and LSCF-gas interfaces. Due to the fact that it can be performed easily in air on large-area electrodes, GDC pre-infiltration is likely more commercially viable than ALD ZrO 2 overcoating as an interfacial Sr gettering technique. Combining ZrO 2 overcoating with GDC pre-infiltration was not successful because the GDC nano-particles gettered the ZrO 2 overcoat instead of the interfacial Sr.

30 DIRECT ENERGY CONVERSION↗

Improved Fabrication Of Cathodes For Solid-State Li Cells

Utilization of cathode material increased. Improved composite-cathode/polymer-electrolyte units for solid-state lithium secondary electrochemical cells fabricated in modified version of original method of fabrication. Further development of units may lead to increases in energy and power densities and in cycle lives of rechargeable lithium cells.

Nagasubramanian, Ganesan↗

Nanostructured ligament and fiber Al–doped Li 7 La 3 Zr 2 O 12 scaffolds to mediate cathode-electrolyte interface chemistry

In this study, scaffold structures of electrospun aluminum–substituted lithium lanthanum zirconate Li 7 La 3 Zr 2 O 12 (Al-LLZO) were synthesized and used as an additive in a LiNi 0.6 Mn 0.2 Co 0.2 O 2 composite cathode. The scaffolds were crystalized in the cubic phase after calcination at 700 °C. The Al-LLZO scaffold morphology was dependent on the precursor formulation (aqueous and dimethylformamide. The aqueous precursors resulted in scaffolds of densely coalesced ligaments, whereas the dimethylformamide precursors resulted in high–aspect ratio nanofiber scaffolds. The long-term cycling stability and rate performance of the cells were found to depend on the Al-LLZO scaffold morphology. The uniformly dispersed Al-LLZO fibers resulted in a more stable cathode electrolyte interface formation through the reduced decomposition of the LiPF 6 salt during cycling, resulting in a better high-rate and long-term cycling performance.

25 ENERGY STORAGE↗

LT-LiNi 1/3 Mn 1/3 Co 1/3 O 2 : A Partially-Disordered, Composite Rock Salt Cathode Prepared by Flame Spray Pyrolysis for Li-Ion Batteries

A unique composite cathode structure for Li-ion batteries, designated LT-LiNi 1/3 Mn 1/3 Co 1/3 O 2 (or LT-NMC111), has been prepared by flame spray pyrolysis and subsequent annealing between 400 and 650 °C. It is composed predominantly of structurally-integrated and partially-disordered lithiated-spinel and layered components, both of which can be broadly described as partially-disordered rock salt constituents. The paper describes the evolution of the LT-NMC111 structure as a function of the synthesis method, annealing temperature, and electrochemical properties in the context of other recently reported “low-temperature” (LT) materials, such as LT-LiCo 1−x Al x O 2 and LT-LiMn 0.5 Ni 0.5 O 2 or, in spinel notation, LT-Li 2 Co 2–2x Al 2x O 4 and LT-Li 2 MnNiO 4 , respectively.

25 ENERGY STORAGE↗

The Riddle of Dark LLZO: Cobalt Diffusion in Garnet Separators of Solid‐State Lithium Batteries

Abstract Solid‐state batteries (SSBs) with a Li 7 La 3 Zr 2 O 12 (LLZO) garnet electrolyte are attracting much attention as robust and safe alternative to conventional lithium‐ion batteries. Technical challenges in the practical implementation of garnet SSBs are related to the need for high‐temperature sintering, which often leads to undesirable chemical reactions with the cathode material. While these reactions are well understood for composite cathodes, very little is known about similar processes between cathode and separator during battery fabrication. This work focuses on understanding the processes between the composite LiCoO 2 ‐LLZO cathode and the LLZO separator and how they affect the battery performance. The extensive diffusion of Co‐ions within LLZO, which leads to the often‐observed LLZO darkening, is shown to have a significant impact on ionic conductivity, electronic conductivity, and dendrite stability of the separator. Experimental data coupled with large‐scale molecular dynamics simulations uncover the diffusion mechanism for Co‐ions and identify secondary phases that form during these interactions. In addition to extensive Co‐ion diffusion within the grains, a non‐uniform segregation of Co‐ions at grain boundaries is found leading to the formation of three distinct Co‐containing phases. This work offers a general approach to studying the fundamental ion diffusion processes that occur during the fabrication of oxide SSBs.

electrochemical properties↗

Characterization of plasma chemistry and ion energy in cathodic arc plasma from Ti-Si cathodes of different compositions

Arc plasma from Ti-Si compound cathodes with up to 25 at. % Si was characterized in a DC arc system with respect to chemistry and charge-state-resolved ion energy. The plasma ion composition showed a lower Si content, diverging up to 12 at. % compared to the cathode composition, yet concurrently deposited films were in accordance with the cathode stoichiometry. Significant contribution to film growth from neutrals is inferred besides ions, since the contribution from macroparticles, estimated by scanning electron microscopy, cannot alone account for the compositional difference between cathode, plasma, and film. The average ion charge states for Ti and Si were higher than reference data for elemental cathodes. This result is likely related to TiSi{sub x} phases of higher cohesive energies in the compound cathodes and higher effective electron temperature in plasma formation. The ion energy distributions extended up to {approx}200 and {approx}130 eV for Ti and Si, respectively, with corresponding average energies of {approx}60 and {approx}30 eV. These averages were, however, not dependent on Si content in the cathode, except for 25 at. % Si where the average energies were increased up to 72 eV for Ti and 47 eV for Si.

36 MATERIALS SCIENCE↗

Effect of commercial activated carbons in sulfur cathodes on the electrochemical properties of lithium/sulfur batteries

Highlights: • The sulfur/activated carbon composite is fabricated using commercial activated carbons. • The sulfur/activated carbon composite with coal shows the best performance. • The Li/S battery has capacities of 1240 mAh g{sup −1} at 1 C and 567 mAh g{sup −1} at 10 C. - Abstract: We prepared sulfur/active carbon composites via a simple solution-based process using the following commercial activated carbon-based materials: coal, coconut shells, and sawdust. Although elemental sulfur was not detected in any of the sulfur/activated carbon composites based on Thermogravimetric analysis, X-ray diffraction, and Raman spectroscopy, Energy-dispersive X-ray spectroscopy results confirmed its presence in the activated carbon. These results indicate that sulfur was successfully impregnated in the activated carbon and that all of the activated carbons acted as sulfur reservoirs. The sulfur/activated carbon composite cathode using coal exhibited the highest discharge capacity and best rate capability. The first discharge capacity at 1 C (1.672 A g{sup −1}) was 1240 mAh g{sup −1}, and a large reversible capacity of 567 mAh g{sup −1} was observed at 10 C (16.72 A g{sup −1}).

36 MATERIALS SCIENCE↗

DEGRADATION IN PERFORMANCE OF LANTHANUM STRONTIUM MANGANITE BASED SOLID OXIDE FUEL CELL CATHODES UNDER ACCELERATED TESTING

The performance of solid oxide fuel cells (SOFCs) with three different lanthanum strontium manganite (LSM) based cathode compositions were evaluated. All cells were yttria-stabilized zirconia (Zr0.92Y0.08O2-δ, 8YSZ) electrolyte-supported button cells, consisting of a nickel oxide – yttria-stabilized zirconia (NiO-8YSZ) anode and a cathode of 8YSZ and LSM. The three LSM compositions differed in the amount of excess Mn: Composition A was (La0.85Sr0.15)0.90MnO3±δ (10% excess Mn); Composition B was (La0.80Sr0.20)0.95MnO3±δ (5% excess Mn); and Composition C was (La0.80Sr0.20)0.98MnO3±δ (2% excess Mn). The cells were tested under conventional and accelerated conditions, where the accelerated conditions were meant to simulate the results of months of long-term testing in just 500 hours (approximately three weeks) of testing by using high operating temperature and current density. Accelerated tests showed lower degradation rates, lower continuous area specific resistance (ASR), and higher power output than conventional tests for all cathode compositions. Continuous measurements of the cells' output voltage versus time, together with periodic electrochemical impedance spectroscopy (EIS) measurements, were used to evaluate the performance of the cells in terms of ASR degradation rates (% ASR rise per kh) and power outputs. The EIS measurements also permitted a partial deconvolution of the cathode ASR from the anode ASR. Cathodes with 10% excess Mn tested under accelerated conditions had the lowest degradation rates, but the highest continuous ASR and lowest power outputs. Cathodes with 2% excess Mn tested under accelerated conditions had the lowest continuous ASR and highest power outputs; thus it was concluded that cells with the lowest amount of excess Mn cathodes performed the best.

08 HYDROGEN↗

Overcoming phase instability of RBaCo2O5+ (R = Y and Ho) by Sr substitution for application as cathodes in solid oxide fuel cells

Phase instabilities of the RBaCo2O5+ (R = Y and Ho) layered-perovskites and their decompositions into RCoO3 and BaCoO3-z at 800 oC in air were investigated. This will restrict their high temperature applications such as cathodes in solid oxide fuel cell (SOFC). However, appropriate amount of Sr substitution ( 60 % for R = Y and 70 % for R = Ho) for Ba successfully stabilized the R(Ba1-xSrx)Co2O5+ phase at elevated temperatures. This can be explained by decreasing oxygen vacancies at R-O layer, decreasing R-O bonding length, and consequent improvement of structural integrity. In addition, the Sr substitution (x = 0.6 - 1.0) for Ba provided added benefit with respect to the chemical stability against Ce0.8Gd0.2O1.9 (GDC) electrolyte, which is a critical requirement for the cathodes in SOFC. Among the various compositions investigated, the Y(Ba0.3Sr0.7)Co2O5+ + GDC composite cathode delivered the optimum electrochemical performances with a stable phase demonstrating the potential as a cathode in SOFC.

HoBaCo2O5+↗

Challenges for and Pathways Toward Solid-State Batteries

Solid-state batteries utilizing lithium metal anodes have the potential to enable batteries with a specific energy of >500 Wh/kg and an energy density of >1,500 Wh/L for thousands of cycles. When optimized they will improve the energy efficiency, operating temperature range, sustainability, and safety at a lower cost compared to projections for advanced Li-ion batteries. This improved performance is critical for the widespread adoption of electric vehicles and may enable future applications such as electric aviation. Expectations for solid-state batteries are high, there are significant materials and processing challenges that need to be overcome. Some of these challenges are well known; others are more subtle and are just becoming known. The challenges and their solutions must be clearly identified to realize high-energy solid-state Li metal batteries. In the United States, the U.S. Department of Energy (DOE) funds the majority of energy storage research and development, including solid state battery research. Web of Science publication analysis shows that worldwide DOE is second largest funder. Work on solid state batteries is distributed across different arms of DOE and is coordinated at headquarters to ensure a broad national portfolio for advanced batteries, including lithium batteries and solid-state battery devices. We note that university and national laboratory researchers in the US with a long-standing interest in solid state batteries is a small, integrated community with recognized impact for publications, patents and startup companies. The opportunity for this group to engage for research with international colleagues is growing, fostered by periodic bilateral meetings supported by DOE and by the recent joint US German research program for lithium battery interface studies. These are valuable opportunities to speed solid-state battery development. The ORNL led virtual workshop, overviewed here, confirms the community’s shared vision of the exciting advances, opportunities, and challenges. Further, we are seeing that this workshop has spawned several new informal collaborations and draft proposals. This encourages us to propose future discussion. On May 11, 2020, Oak Ridge National Laboratory (ORNL) hosted a 6-hour, on-line national workshop to discuss recent advances and most the prominent obstacles to realizing solid-state Li metal batteries. The workshop included more than 30+ experts from national laboratories, universities, and companies, all of whom have worked on solid-state batteries for multiple years. The participants shared recent advances, many not yet in print, illustrating that the community has gained significant new insights for solid-state Li battery materials over the last 5 years. In this report, the major outcomes of the workshop are organized to identify the gaps in our scientific knowledge for four core materials science areas: (1) Li metal anodes, (2) the solid electrolyte in contact with Li metal, (3) active cathode materials and solid-state composite cathodes, and (4) solid electrolytes. Illustrative examples and discussions are reported with the more comprehensive issues in the report. Discussion of additional challenges related to processing of solid-state battery materials and to the designs and architectures for mechanically robust, long-lived batteries received less attention due to time constraints. These are good themes for deeper discussion at a follow-on workshop, where a complete list of critical research topics can be identified.

25 ENERGY STORAGE↗

Methods of flash sintering

This disclosure provides methods of flash sintering and compositions created by these methods. Methods for sintering multilayered bodies are provided in which a sintered body is produced in less than one minute. In one aspect, each layer is of a different composition, and may be constituted wholly from a ceramic or from a combination of ceramic and metallic particles. When the body includes a layer of an anode composition, a layer of an electrolyte composition and a layer of a cathode composition, the sintered body can be used to produce a solid oxide fuel cell.

30 DIRECT ENERGY CONVERSION↗

Resolving Chemical and Spatial Heterogeneities at Complex Electrochemical Interfaces in Li-Ion Batteries

The high specific capacities of Ni-rich transition metal oxides have garnered immense interest for improving the energy density of Li-ion batteries (LIBs). Despite the potential of these materials, Ni-rich cathodes suffer from interfacial instabilities that lead to crystallographic rearrangement of the active material surface as well as the formation of a cathode electrolyte interphase (CEI) layer on the composite during electrochemical cycling. While changes in crystallographic structure can be detected with diffraction-based methods, probing the chemistry of the disordered, heterogeneous CEI layer is challenging. In this work, we use a combination of ex situ solid-state nuclear magnetic resonance (SSNMR) spectroscopy and X-ray photoemission electron microscopy (XPEEM) to provide chemical and spatial information, on the nanometer length scale, on the CEI deposited on LiNi 0.8 Mn 0.1 Co 0.1 O 2 (NMC811) composite cathode films. XPEEM elemental maps offer insight into the lateral arrangement of the electrolyte decomposition products that comprise the CEI and paramagnetic interactions (assessed with electron paramagnetic resonance (EPR) and relaxation measurements) in 13 C SSNMR provide information on the radial arrangement of the CEI from the NMC811 particles outward. Using this approach, here we find that LiF, Li 2 CO 3 , and carboxy-containing structures are directly appended to NMC811 active particles, whereas soluble species detected during in situ 1 H and 19 F solution NMR experiments (e.g., alkyl carbonates, HF, and vinyl compounds) are randomly deposited on the composite surface. We show that the combined approach of ex situ SSNMR and XPEEM, in conjunction with in situ solution NMR, allows spatially-resolved, molecular-level characterization of paramagnetic surfaces and new insights into electrolyte oxidation mechanisms in porous electrode films.

36 MATERIALS SCIENCE↗