Search NASA⌕ Search

SEARCH · Search NASA

Results for “Correlation of Full-Scale”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Geometry considerations for jet noise shielding with CTOL engine-over-the-wing concept

Jet noise shielding benefits for CTOL engine-over-the-wing installations were obtained with various model-scale circular nozzles and wing chord geometries. Chord-to-nozzle diameter ratios were varied from 3 to 20, while ratios of nozzle height above the wing to the diameter were varied from near zero to 3. Spectral noise data were obtained with jet velocities from 640 to 1110 ft/sec. Characteristics of low frequency noise sources are discussed. Jet-noise shielding is correlated in terms of acoustic and geometric parameters. Implications of extending the model-scale data to full-scale are discussed.

Von Glahn, U.↗
NASA NTRS1974

Investigation of noise from full-scale high bypass engine and blown flap system

A summary is presented of an acoustic test program for investigating engine noise suppression and jet/flap interaction noise associated with an externally blown flap (EBF) STOL powered lift system. A highly suppressed TF-34 engine and EBF wing were used in the investigation. The engine was suppressed 21 PndB to a level of 94 PndB. An under the wing (UTW) powered lift system was tested with conventional, mixer, and decayer-type nozzles. The configuration with velocity decayer nozzle and acoustically treated shroud had the lowest noise (98 PndB). An over the wing (OTW) configuration with nondecayer nozzle was about 10 dB quieter than the corresponding UTW system. UTW and OTW noise data are compared with scale model correlations.

Jones, W. L.↗
NASA NTRS1982

Effects of wing-leading-edge modifications on a full-scale, low-wing general aviation airplane: Wind-tunnel investigation of high-angle-of-attack aerodynamic characteristics

Wing-leading-edge modifications included leading-edge droop and slat configurations having full-span, partial-span, or segmented arrangements. Other devices included wing-chord extensions, fences, and leading-edge stall strips. Good correlation was apparent between the results of wind-tunnel data and the results of flight tests, on the basis of autorotational stability criterion, for a wide range of wing-leading-edge modifications.

Newsom, W. A., Jr.↗
NASA NTRS1982

The need for an optical transition detection system in the NTF

Methods for transition detection were studied. The very high test and model costs necessitate testing of any new configuration over a range of Reynolds numbers for correlation with data obtained in conventional tunnels. The Reynolds number variations will be carried out at constant dynamic pressure, i.e., constant aeroelastic condition, by varying test temperature. Boundary layer transition cannot be expected to occur at the full scale location at significantly less than full-scale Reynolds numbers, and transition patterns will change with varying Reynolds number. Knowledge of the location of transition on model surfaces is essential for correct interpretation of drag data. The importance of transition, the limitations of artificial transition fixing, and their relation to the NTF are reviewed. The calculated minimum roughness height to instantaneously trip transition on a model transport wing over a range of Reynolds numbers of interest is shown in the NTF.

Fancher, M. F.↗
NASA NTRS1987

Comparing Test Data on Scale-Model Helicopter Rotors

Hovering data correlate well, but forward-flight data do not. Report compares acoustics and performance of small-scale helicopter rotor with those of full-scale rotor in both hovering and forward flight.

Kitaplioglu, Cahit↗
NASA NTRS1988

Use of Dynamically Scaled Models for Studies of the High-Angle-of-Attack Behavior of Airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1988

Use of dynamically scaled models for studies of the high-angle-of-attack behavior of airplanes

Dynamically scaled, free-flying models are used by the National Aeronautics and Space Administration (NASA) to study the stalling and spinning characteristics of civil and military airplane configurations. Such tests have been conducted for many different designs, and it has been possible to correlate the results predicted by the model tests with flight test results obtained in the investigations. The present paper describes four of the dynamic model testing techniques used at the NASA Langley Research Center, including the scaling laws used in the construction of models and in the interpretation of results. Predictions of stall/spin behavior based on model results have generally been very accurate, and the model tests are regarded as an invaluable precursor to full-scale flight tests. However, aerodynamic scale effects between some models and full-scale airplanes due to differences in test values of Reynolds number have resulted in erroneous predictions for a few configurations. A discussion of these effects is provided, together with the approach used to modify the model so that its behavior more closely matches that of the airplane. Finally, two typical applications of the techniques to the X-29A research airplane and several general aviation research airplanes are presented to illustrate the type of information provided by the tests.

Joseph R Chambers↗
NASA NTRS1990

Predictions of F-111 TACT aircraft buffet response

A summary is presented for the prediction method development and correlations of predicted response with flight test measurements. The prediction method was based on refinements to the method described by Cunningham. One improvement made use of direct time integration of the correlated fluctuating pressure data to obtain buffet excitation for the various modes of interest. Another improvement incorporated a hybrid technique for scaling measured wind tunnel damping data to full-scale for the modes of interest. A third improvement made use of the diagonalized form of the fully coupled equations of motion. Finally, a mechanism was described for explaining an apparent coupling between the aircraft wing torsion modes and shock induced trailing edge separation that led to very high wing motion on the aircraft that was not observed on the wind tunnel model.

Cunningham, Atlee M., Jr.↗
NASA NTRS1992

Aerodynamic roughness measured in the field and simulated in a wind tunnel

This study evaluates how well values of aerodynamic surface roughness, z sub 0, measured over scale models in wind tunnels correlate with values of z sub 0 measured at full scale in the field. A field experiment was conducted in which values of z sub 0 and u* (wind friction speed) were measured over three arrays of non-erodible roughness elements on a dry lake bed. Wind profiles were measured by ten anemometers on a 15 m mast under thermally neutral atmospheric conditions. Values of z sub 0 increased from .00014 m (dry lake bed only) to .026 m with increasing roughness element density. The three roughness element arrays were simulated at 1/10 and 1/20 scale in an open-circuit atmospheric boundary-layer wind tunnel. Velocities were measured with a boundary-layer pitot-tube rake from the same relative position within the scale model arrays as the anemometers were relative to the field arrays. Each array at each scale was sampled three times at five freestream velocities. Average values of z sub 0 for each model array at each scale were compared with full-scale values of z sub 0 obtained in the field. The field vs. wind tunnel correspondence of z sub 0 is found to be z sub 0 field = 0.2661 x (z sub(0 model) x scale(exp -1))exp .8159.

Sullivan, Robert↗
NASA NTRS1994

Theoretical study of the effect of an AlGaAs double heterostructure on metal-semiconductor-metal photodetector performance

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potentialflow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid threedimensional flow features for several intricate geometrical regions.

Salem, Ali F.↗
NASA NTRS1995

Three-dimensional aerodynamic analysis of a subsonic transport high-lift configuration and comparisons with wind-tunnel test results

The sizing and efficiency of an aircraft is largely determined by the performance of its high-lift system. Subsonic civil transports most often use deployable multi-element airfoils to achieve the maximum-lift requirements for landing, as well as the high lift-to-drag ratios for take-off. However, these systems produce very complex flow fields which are not fully understood by the scientific community. In order to compete in today's market place, aircraft manufacturers will have to design better high-lift systems. Therefore, a more thorough understanding of the flows associated with these systems is desired. Flight and wind-tunnel experiments have been conducted on NASA Langley's B737-100 research aircraft to obtain detailed full-scale flow measurements on a multi-element high-lift system at various flight conditions. As part of this effort, computational aerodynamic tools are being used to provide preliminary flow-field information for instrumentation development, and to provide additional insight during the data analysis and interpretation process. The purpose of this paper is to demonstrate the ability and usefulness of a three-dimensional low-order potential flow solver, PMARC, by comparing computational results with data obtained from 1/8 scale wind-tunnel tests. Overall, correlation of experimental and computational data reveals that the panel method is able to predict reasonably well the pressures of the aircraft's multi-element wing at several spanwise stations. PMARC's versatility and usefulness is also demonstrated by accurately predicting inviscid three-dimensional flow features for several intricate geometrical regions.

Edge, D. Christian↗
NASA NTRS1999

Evaluation of a Scaling Approach for Stiffened Composite Flat Panels Loaded in Compression

Results of an experimental study of the effects of geometric scaling on a graphite-epoxy flat stiffened-skin panel concept loaded in compression are presented. The scaled models were fabricated using an approach to laminate thickness scaling, referred to as the "ply-thickness method." The structural response and failure characteristics of full-, half-, and quarter-scale specimens fabricated with this scaling concept are discussed and compared. The scaled up failure loads of the half- and quarter-scale models agree well with the failure load of the full-scale prototypes tested. The strength scale effects observed in the results were substantially smaller than those in earlier studies that employed other laminate scaling techniques. The experimental results indicate that failure initiated by crippling and delamination in the cap of the longitudinal stiffeners and skin-stiffener separation at the bond-lines, and was followed by failure of the specimen skin. Nonlinear finite element analysis results correlate well with experimental results up to failure.

Rouse, Marshall↗
NASA NTRS1999

Acoustic Treatment Design Scaling Methods: Advanced Treatment Impedance Models for High Frequency Ranges - Volume 2

The primary purpose of this study is to develop improved models for the acoustic impedance of treatment panels at high frequencies, for application to subscale treatment designs. Effects that cause significant deviation of the impedance from simple geometric scaling are examined in detail, an improved high-frequency impedance model is developed, and the improved model is correlated with high-frequency impedance measurements. Only single-degree-of-freedom honeycomb sandwich resonator panels with either perforated sheet or "linear" wiremesh faceplates are considered. The objective is to understand those effects that cause the simple single-degree-of- freedom resonator panels to deviate at the higher-scaled frequency from the impedance that would be obtained at the corresponding full-scale frequency. This will allow the subscale panel to be designed to achieve a specified impedance spectrum over at least a limited range of frequencies. An advanced impedance prediction model has been developed that accounts for some of the known effects at high frequency that have previously been ignored as a small source of error for full-scale frequency ranges.

Kraft, R. E.↗
NASA NTRS2000

Flying Qualities Evaluation of a Commuter Aircraft With an Ice Contaminated Tailplane

During the NASA/FAA (Federal Aviation Administration) Tailplane Icing Program, pilot evaluations of aircraft flying qualities were conducted with various ice shapes attached to the horizontal tailplane of the NASA Twin Otter Icing Research Aircraft. Initially, only NASA pilots conducted these evaluations, assessing the differences in longitudinal flight characteristics between the baseline or clean aircraft, and the aircraft configured with an Ice Contaminated Tailplane (ICT). Longitudinal tests included Constant Airspeed Flap Transitions, Constant Airspeed Thrust Transitions, zero-G Pushovers, Repeat Elevator Doublets, and Simulated Approach and Go-Around tasks. Later in the program, guest pilots from government and industry were invited to fly the NASA Twin Otter configured with a single full-span artificial ice shape attached to the leading edge of the horizontal tailplane. This shape represented ice formed due to a 'Failed Boot' condition, and was generated from tests in the Glenn Icing Research Tunnel on a full-scale tailplane model. Guest pilots performed longitudinal handling tests, similar to those conducted by the NASA pilots, to evaluate the ICT condition. In general, all pilots agreed that longitudinal flying qualities were degraded as flaps were lowered, and further degraded at high thrust settings. Repeat elevator doublets demonstrated reduced pitch damping effects due to ICT, which is a characteristic that results in degraded flying qualities. Pilots identified elevator control force reversals (CFR) in zero-G pushovers at a 20 deg flap setting, a characteristic that fails the FAR 25 no CFR certification requirement. However, when the same pilots used the Cooper-Harper rating scale to perform a simulated approach and go-around task at the 20 deg flap setting, they rated the airplane as having Level I and Level II flying qualities respectively. By comparison, the same task conducted at the 30 deg flap setting, resulted in Level II flying qualities for the approach portion, and Level III for the go-around portion.The results of this program indicate that safe and acceptable flying qualities with an ICT condition, can be effectively assessed by task-oriented pilot maneuvers. In addition, other maneuvers such as repeat elevator doublets provide good qualitative and quantitative assessments of pitch damping and elevator effectiveness, which are characteristics that correlate well with pilot task ratings. The results of this testing indicate that the FAR 25 zero-G pushover maneuver, which requires no CFR during its execution, may be an overly conservative pass/fail criteria for aircraft certification.

Ranaudo, Richard J.↗
NASA NTRS2002

Experimental Investigation of Water Droplet Impingement on Airfoils, Finite Wings, and an S-duct Engine Inlet

Validation of trajectory computer codes, for icing analysis, requires experimental water droplet impingement data for a wide range of aircraft geometries as well as flow and icing conditions. This report presents improved experimental and data reduction methods for obtaining water droplet impingement data and provides a comprehensive water droplet impingement database for a range of test geometries including an MS(1)-0317 airfoil, a GLC-305 airfoil, an NACA 65(sub 2)-415 airfoil, a commercial transport tail section, a 36-inch chord natural laminar flow NLF(1)-0414 airfoil, a 48-inch NLF(1)-0414 section with a 25 percent chord simple flap, a state-of-the-art three-element high lift system, a NACA 64A008 finite span swept business jet tail, a full-scale business jet horizontal tail section, a 25 percent-scale business jet empennage, and an S-duct turboprop engine inlet. The experimental results were obtained at the NASA Glenn Icing Research Tunnel (IRT) for spray clouds with median volumetric diameter (MVD) of 11, 11.5, 21, 92, and 94 microns and for a range of angles of attack. The majority of the impingement experiments were conducted at an air speed of 175 mph corresponding to a Reynolds number of approximately 1.6 million per foot. The maximum difference of repeated tests from the average ranged from 0.24 to 12 percent for most of the experimental results presented. This represents a significant improvement in test repeatability compared to previous experimental studies. The increase in test repeatability was attributed to improvements made to the experimental and data reduction methods. Computations performed with the LEWICE-2D and LEWICE-3D computer codes for all test configurations are presented in this report. For the test cases involving median volumetric diameters of 11 and 21 microns, the correlation between the analytical and experimental impingement efficiency distributions was good. For the median volumetric diameters of 92 and 94-micron cases, however, the analysis produced higher impingement efficiencies and larger impingement limits than the experiment. It is speculated that this discrepancy is due to droplet splashing and breakup experienced by large droplets during impingement.

Papadakis, Michael↗
NASA NTRS2003

Analysis and Test Correlation of Proof of Concept Box for Blended Wing Body-Low Speed Vehicle

The Low Speed Vehicle (LSV) is a 14.2% scale remotely piloted vehicle of the revolutionary Blended Wing Body concept. The design of the LSV includes an all composite airframe. Due to internal manufacturing capability restrictions, room temperature layups were necessary. An extensive materials testing and manufacturing process development effort was underwent to establish a process that would achieve the high modulus/low weight properties required to meet the design requirements. The analysis process involved a loads development effort that incorporated aero loads to determine internal forces that could be applied to a traditional FEM of the vehicle and to conduct detailed component analyses. A new tool, Hypersizer, was added to the design process to address various composite failure modes and to optimize the skin panel thickness of the upper and lower skins for the vehicle. The analysis required an iterative approach as material properties were continually changing. As a part of the material characterization effort, test articles, including a proof of concept wing box and a full-scale wing, were fabricated. The proof of concept box was fabricated based on very preliminary material studies and tested in bending, torsion, and shear. The box was then tested to failure under shear. The proof of concept box was also analyzed using Nastran and Hypersizer. The results of both analyses were scaled to determine the predicted failure load. The test results were compared to both the Nastran and Hypersizer analytical predictions. The actual failure occurred at 899 lbs. The failure was predicted at 1167 lbs based on the Nastran analysis. The Hypersizer analysis predicted a lower failure load of 960 lbs. The Nastran analysis alone was not sufficient to predict the failure load because it does not identify local composite failure modes. This analysis has traditionally been done using closed form solutions. Although Hypersizer is typically used as an optimizer for the design process, the failure prediction was used to help gain acceptance and confidence in this new tool. The correlated models and process were to be used to analyze the full BWB-LSV airframe design. The analysis and correlation with test results of the proof of concept box is presented here, including the comparison of the Nastran and Hypersizer results.

Spellman, Regina L.↗
NASA NTRS2003

Calculation of Rotor Performance and Loads Under Stalled Conditions

Rotor behavior in stalled conditions is investigated using wind tunnel test data of a l/l0-scale CH-47B/C type rotor, which provides a set of test conditions extending from unstalled to light stall to some deep stall conditions over a wide range of advance ratios. The rotor performance measured in the wind tunnel is similar to the main rotor performance measured during the NASA/Army UH-60A Airloads Program, although the two rotors are quite different. The analysis CAMRAD II has been used to predict the rotor performance and loads. Full-scale airfoil test data are corrected for Reynolds number effects for comparison with the model-scale rotor test. The calculated power coefficient shows good correlation with the measurements below stall with the Reynolds number-corrected airfoil table. Various dynamic stall models are used in the calculations. The Boeing model shows the lift augmentation at low advance ratios and the Leishman-Beddoes model shows better correlation of torsion moment than the other models at mu = 0.2. However, the dynamic stall models, in general, show only a small influence on the rotor power and torsion moment predictions especially at higher advance ratios.

Yeo, Hyeonsoo↗
NASA NTRS1947

Correlation of the Trim Limits of Stability Obtained for a PB2Y-3 Flying Boat and a 1/8-Size Powered Dynamic Model

Tests of a PB2Y-3 flying boat were made at the U.S> Naval Air Station, Patuxent River, Md., to determine its hydrodynamic trim limits of stability. Corresponding tests were also made of a 1/8-size powered dynamic model of the same flying boat in Langley tank no. 1. During the tank tests, the full-size testing procedure was reproduced as closely as possible in order to obtain data for a direct correlation of the results. As a nominal gross load of 66,000 pounds, the lower trim limits of the full-size and model were in good agreement above a speed of 80 feet per second. As the speed decreased below 80 feet per second, the difference between the model trim limits and full-scale trim limits gradually became larger. The upper trim limit of the model with flaps deflected 0 deg was higher than that of the full-size, but the difference was small over the speed range compared. At flap deflections greater than 0 deg, it was not possible to trim either the model of the airplane to the upper limit with the center of gravity at 28 percent of the mean aerodynamic chord. The decrease in the lower trim limits with increase in flap deflection showed good agreement for the airplane and model. The lower trim limits obtained at different gross loads for the full-size airplane were reduced to approximately a single curve by plotting trim against the square root of C(sub delta (sub o)) divided by C(sub V).

Garrison, Charlie C.↗