Search NASA⌕ Search

SEARCH · Search NASA

Results for “Cross-Sectional Studies”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1982

Turbulent boundary layer drag reduction using riblets

An experimental study of low-speed turbulent boundary layer flow over longitudinally grooved surfaces (i.e., riblets) is discussed. Results obtained with a highly accurate drag balance indicate that v-groove riblet surfaces can produce consistent net drag reductions as large as 8 percent provided the height and spacing of the grooves in terms of law of the wall variables are less than 25 wall units. Momentum balances confirmed these direct drag measurements. Conditionally sampled data indicate that the burst frequency for riblets is approximately the same as that for a flat plate but turbulence intensity is reduced. Attempts to optimize the net drag reduction by varying riblet cross-sectional geometry and alignment are also discussed.

Walsh, M. J.↗
NASA NTRS1984

Ultrasonic and optical evaluation of surgical implant materials and devices. A durability study of pericardial bioprostheses

Laser Doppler Anemometry (LDA) and accelerated fatigue testing were used in an attempt to assess the durability of two cardiac value bioprostheses. The LDA system was used to monitor the function of the cardiac valves over time. This was done through flow characterization in an aortic flow chamber, designed to closely simulate in vivo conditions, both in the near vicinity (sinuses of valsalva region) and also somewhat downstream (aortic region) from the values. The accelerated fatigue tester was operated by opening and closing the valves at a rate of 1300 R.P.M., about 18 x the normal rate. The results from the two test valves indicate a definite change in the flow characteristics downstream from the valve after certain accelerated test intervals. The high velocity cross-sectional flow area seems to increase over time in use, causing a decrease in the peak velocity. The tissue became more flaccid in certain areas, and tears were apparent at about 9.4 million cycles for the Ionescu-Shiley valve and at 24 million cycles for the Carpentier-Edwards valve. The use of Doppler ultrasound as a technique for monitoring the function of bioprostheses over time in vivo is also discussed.

Schuster, P. R.↗
NASA NTRS1975

Research on metal solidification in zero-g state

The containerless solidification of several pure metals and metallic alloys was studied in a low gravity environment. The tests were performed in the MSFC 4.2 s drop tower using a rapid wire melting apparatus designed and built for this purpose. Pure iron and nickel, and alloys of iron-nickel, iron-carbon, nickel-aluminum and tungsten-rhenium were all melted and solidified at a gravity level of approximately 100.000/-4 g. Interpretation of the results has led to an appreciation of the factors controlling the successful execution of this drop test experiment and to a delineation of the limits of applicability of the apparatus. Preliminary metallurgical evaluations are presented of the overall shapes, lattice parameters, surface microstructure,, cross-sectional microstructures, solidification and transformation sequences, evaporative segregation, and localized solute redistribution observed in the low-gravity specimens. The effects of low gravity on metallic solidification are discussed with particular emphasis on observations of spontaneous undercooling and evaporative segregation in uncontained melts.

Papazian, J. M.↗
NASA NTRS1981

An experimental study of the flow in a wing with a partial span drooped leading edge

The flow field produced by a low aspect ratio wing (AR = 3.0) with a partial span leading edge droop was investigated in a series of low speed wind tunnel tests (Reynolds number based on 17.8 cm chord = 560,000). Photographs were obtained of surface oil flow patterns over an angle of attack range of alpha = 0 to 29 deg. Flow field surveys of the partially stalled wing at alpha = 25 deg were completed using a hot-wire probe, a split-film probe and a Conrad probe. The flow field survey data was presented using a color video display. The data indicated regions of apparent reversed flow in the separation region behind the wing and indicated the general cross-sectional shape of the separated wake flow.

Winkelmann, A. E.↗
NASA NTRS1987

Computational chemistry research

Task 41 is composed of two parts: (1) analysis and design studies related to the Numerical Aerodynamic Simulation (NAS) Extended Operating Configuration (EOC) and (2) computational chemistry. During the first half of 1987, Dr. Levin served as a member of an advanced system planning team to establish the requirements, goals, and principal technical characteristics of the NAS EOC. A paper entitled 'Scaling of Data Communications for an Advanced Supercomputer Network' is included. The high temperature transport properties (such as viscosity, thermal conductivity, etc.) of the major constituents of air (oxygen and nitrogen) were correctly determined. The results of prior ab initio computer solutions of the Schroedinger equation were combined with the best available experimental data to obtain complete interaction potentials for both neutral and ion-atom collision partners. These potentials were then used in a computer program to evaluate the collision cross-sections from which the transport properties could be determined. A paper entitled 'High Temperature Transport Properties of Air' is included.

Levin, Eugene↗
NASA NTRS1985

A Cerenkov-delta E-Cerenkov detector for high energy cosmic ray isotopes and an accelerator study of Ar-40 and Fe-56 fragmentation

A high energy cosmic ray detector--the High Energy Isotope Spectrometer Telescope (HEIST) is described. It is a large area (0.25 m(swp 2) SR) balloon borne isotope spectrometer designed to make high resolution measurements of isotopes in the element range from neon to nickel (10 Z 28) at energies of about 2 GeV/nucleon. HEIST determines the mass of individual nuclei by measuring both the change in the Lorentz factor (delta gamma) that results from traversing the NaI stack, and the energy loss (delta E) in the stack. Since the total energy of an isotope is given by E = (gamma M), the mass M can be determined by M = delta E/delta, gamma. The instrument is designed to achieve a typical mass resolution of 0.2 amu. The isotopic composition of the fragments from the breakup of high energy An-40 and Fe-56 nuclei are measured experimentally. Isotope yields are compared with calculated yields based on semi-empirical cross-section formulae.

Lau, K. H.↗
NASA NTRS1985

High thermal capacity cold plate/hot plate

The results of an analytical study to determine the feasibility of a novel two-phase cold plate/hot plate (CPHP) are presented. A key feature of the CPHP is the use of capillary forces to separate the liquid and vapor phases and distribute the liquid over the evaporating/condensing surface. The liquid phase is held by capillary forces in a reservoir and is carried to the evaporating surface by a wick. The reservoir is replenished at intervals from a valved external liquid supply line. In the hot plate mode, liquid accumulates in the reservoir and is removed by an external condensate line. Performance requirements for the device were capability of handling a power density of 4 watts/sq cm, an outlet quality (percentage of vapor flow to total flow) greater than 90 percent, and operation in a 0-g environment. An analytical model of CPHP operation was developed which concentrated on the liquid and vapor flows. It was found that the liquid carrying capillary grooves of rectangular cross-section gave significantly better predicted performance than V-shaped grooves. Using the analytical model, capillary groove width and length, vapor channel dimensions, and other parameters were selected to meet the performance requirements with a 100-percent margin.

Hwangbo, H.↗
NASA NTRS1982

A study of resonant-cavity and fiberglass-filled parallel baffles as duct silencers

Acoustical performance and pressure drop were measured for two types of splitters designed to attenuate sound propagating in ducts - resonant-cavity baffles and fiberglass-filled baffles. Arrays of four baffles were evaluated in the 7- by 10-foot wind tunnel number 1 at Ames Research Center at flow speeds from 0 to 41 m/sec. The baffles were 2.1 m high, 305 to 406 mm thick, and 3.1 to 4.4 m long. Emphasis was on measurements of silencer insertion loss as affected by variations of such parameters as baffle length, baffle thickness, perforated skin geometry, cavity size and shape, cavity damping, wind speed, and acoustic field directivity. An analytical method for predicting silencer performance is described and compared with measurements. With the addition of cavity damping in the form of 25-mm foam linings, the insertion loss above 250 Hz of the resonant-cavity baffles was improved 2 to 7 db compared with the undamped baffles; the loss became equal to or greater than the insertion loss of comparable size fiberglass baffles at frequencies above 250 Hz. Variations of cavity size and shape showed that a series of cavities with triangular cross-sections (i.e., variable depth) were superior to cavities with rectangular cross sections (i.e., constant depth). In wind, the undamped, resonant-cavity baffles generated loud cavity-resonance tones; the tones could be eliminated by cavity damping.

Soderman, P. T.↗
NASA NTRS1959

Stability Characteristics of Two Missiles of Fineness Ratios 12 and 18 with Six Rectangular Fins of Very Low Aspect Ratio Over a Mach Number Range of 1.4 to 3.2

Two rocket-propelled missiles have been test flown by the Langley Pilotless Aircraft Research Division in order to study the stability characteristics of a body with six rectangular fins of very low aspect ratio. The fins, which had exposed aspect ratios of approximately o.o4 and 0.02 per fin, were mounted on bodies of fineness ratios of 12 and 18, respectively. Each body had a nose with a fineness ratio of 3.5 and a cylindrical afterbody. The body and the fin chord of the model having a fineness ratio of 12 were extended the length of 6 body diameters to produce the model with a fineness ratio of 18. The missiles were disturbed in flight by pulse rockets in order to obtain the stability data. The tests were performed over a Mach number range of 1.4 to 3.2 and a Reynolds number range of 2 x 10(exp 6) to 21 x l0(exp 6). The results of these tests indicate that these configurations with the long rectangular fins of very low aspect ratio showed little induced roll" with the missile of highest fineness ratio and longest fin chord exhibiting the least amount. Extending the body and fin chord of the shorter missile six body diameters and thereby increasing the fin area approximately 115 percent increased the lift-curve slope based on body cross-sectional area approximately 40 to 55 percent, increased the dynamic stability by a substantial amount, and increased the drag from 14 to 33 percent throughout the comparable Mach number range. The center-of-pressure location of both missiles remained constant over the Mach number range.

Henning, Allen B.↗
NASA NTRS1987

Right and left ventricular volumes in vitro by a new nongeometric method

We present an evaluation of a new nongeometric technique for calculating right and left ventricular volumes. This method calculates ventricular chamber volumes from multiple cross-sectional echocardiographic views taken from a single point as the echo beam is tilted progressively through the ventricle. Right and left ventricular volumes are calculated from both the approximate short axis and approximate apical position on 20 in vitro human hearts and compared with the actual chamber volumes. The results for both ventricles from both positions are excellent. Correlation coefficients are > 0.95 for all positions; the standard errors are in the range of 5 to 7 mL and the slopes and intercepts for the regression lines are not significantly different from 1 and 0, respectively (except for the left ventricular short-axis intercept). For all positions, approximately 6 to 8 views are needed for peak accuracy (7.5 degrees to 10 degrees separation). This approach offers several advantages. No geometric assumptions about ventricular shape are made. All images are acquired from a single point (or window), and the digitized points can be used to make a three-dimensional reconstruction of the ventricle. Also, during the calculations a volume distribution curve for the ventricle is produced. The shape of this curve can be characteristic for certain situations (ie, right ventricle, short axis) and can be used to make new simple equations for calculating volume. We conclude that this is an accurate nongeometric method for determining both right and left ventricular volumes in vitro.

NASA Discipline Cardiopulmonary↗
NASA NTRS1972

Elastic scattering of 600-MeV protons from H, D, He-3, and He-4.

Study of the elastic scattering of 600-MeV protons from light nuclei. Differential cross sections have been obtained for the scattering of protons from hydrogen, deuterium, helium-3, and helium-4. Polarization was measured for deuterium and He-4 nuclei. The p-p cross-section data are in excellent agreement with the predictions from the Livermore phase shifts. Small-angle p-D, p-He-3 elastic scattering data are compared with calculations based on the multiple-scattering theories of Watson and Glauber.

Boschitz, E. T.↗
NASA NTRS1975

Heavy Ion Fragmentation Experiments at the Bevatron

Fragmentation processes of heavy nuclei in matter using the heavy-ion capability of the Bevatron were studied. The purpose was to obtain the single particle inclusive spectra of secondary nuclei produced at 0 deg by the fragmentation of heavy ion beam projectiles. The process being examined is B+T yields F + anything, where B is the beam nucleus, T is the target nucleus, and F is the detected fragment. The fragments F are isotopically identified by experimental procedures involving magnetic analysis, energy loss and time-of-flight measurements. Attempts were also made to: (1) measure the total and partial production cross section for all isotopes, (2) test the applicability of high-energy multi-particle interaction theory to nuclear fragmentation, (3) apply the cross-section data and fragmentation probabilities to cosmic ray transport theory, and (4) search for systematic behavior of fragment production as a means to improve existing semi-empirical theories of cross sections.

Heckman, H. H.↗
NASA NTRS1976

Heavy ion fragmentation experiments at the bevatron

Collaborative research efforts to study the fragmentation processes of heavy nuclei in matter using heavy ion beams of the Bevatron/Bevalac are described. The goal of the program is to obtain the single particle inclusive spectra of secondary nuclei produced at 0 deg by the fragmentation of heavy ion beam projectiles. The process being examined is B+T yields F + anything, where B is the beam nucleus, T is the target nucleus, and F is the detected fragment. The fragments F are isotopically identified by experimental procedures involving magnetic analysis, energy loss and time-of-flight measurements. Effects were also made to: (a) study processes of heavy nuclei in matter, (b) measure the total and partial production cross section for all isotopes, (c) test the applicability of high energy multiparticle interaction theory to nuclear fragmentation, (d) apply the cross section data and fragmentation probabilities to cosmic ray transport theory, and (e) search for systematic behavior of fragment production as a means to improve existing semi-empirical theories of cross-sections.

Heckman, H. H.↗
NASA NTRS1981

Effect of laser frequency on a collision-induced radiative process

A review is presented of the principles of collision induced radiative processes, followed by an examination of the effects of laser frequencies on these processes. A one-dimensional problem involving two electron states is considered, and it is found that the Hamiltonian of the radiation field is dominated by electric-dipole interaction which couples states of different parity. Transitions are noted to be dependent on collisions, and the complexities of three-dimensional systems are expressed as considerations of the angular momentum of the photon, the necessity of treating different states simultaneously, and the fact that a radiation field destroys rotational invariance. Changing the radiation frequency alters the crossing point and offers opportunities to study the interplay of potential surfaces with molecular dynamics. Experiments on Na+A systems are outlined for several collision energies and various laser frequencies. Multiple crossings were obtained, although the total cross-section, at all energies, decreased at 18,350/cm.

Devries, P. L.↗
NASA NTRS1980

GOASEX observations of Seasat SAR cross-section modulation from surface winds

L-band data from the Seasat SAR and scatterometer are compared with three SAR data sets from the Gulf of Alaska Seasat Experiment to determine the effectiveness of the L-band for determining surface wind speeds. The SAR scans a 100 km swath several hundred km long. Cross sections from the SAR data were measured at the center, and were found to rise and fall with the observed sea level wind speeds. The L-band backscatter was found to be proportional to the square root of the surface winds, with upwind/crosswind differences as large as 10%. Concerted use of the SAR imagery and the scatterometer data are concluded to offer a capability of accurately describing windspeeds in a 25 x 25 km cell down to a 25 x 25 sq m cell. Implementation is noted to depend on further studies for comparisons of upper and lower air wind data.

Thompson, T. W.↗
NASA NTRS1982

Laboratory studies of UV emissions of H2 by electron impact - The Werner- and Lyman-band systems

The vacuum ultraviolet electron-impact-induced fluorescence emissions of H2 were studied for the Lyman and Werner band systems in the range of 120-170 nm, using an optical system containing a photomultiplier and a spectrometer, over an energy range from threshold to 400 eV. The emission cross sections for the Lyman and Werner transitions at 100 eV are determined. The cross-section ratio is in excellent agreement with theoretical calculations and experimental data for the optical oscillator strengths. The cross-section for cascading to the B state is stated as a percentage of the total emission cross section at both 100 and 300 eV, increasing substantially at 20 eV. The vibrational population distribution of the B state is found to be a function of electron-impact energy as the importance of cascading relative to direct excitation changes with electron-impact energy.

Ajello, J. M.↗
NASA NTRS1985

Electron impact excitation of atomic oxygen - Revised cross sections

Revised cross-section values for the excitation of three O I resonance transitions at 1304, 1027, and 989 A, by electron impact on atomic oxygen are presented from threshold to 300 eV. These results are smaller than the excitation cross sections used in some airglow models by a factor of about 2.8. The revised values are in good agreement with recent quantum-scattering calculations. The downward revision is required by new laboratory studies in which the direct and dissociative cross sections for 1304 A excitation were normalized with small probable error to the O and O2 ionization cross sections. The results also reflect new advances in VUV optical calibration techniques. A number of outstanding airglow problems are simplified by these revisions.

Zipf, E. C.↗
NASA NTRS1985

Absorption Cross-Sections of Sodium Diatomic Molecules

The absorption cross sections of sodium dimers were studied using a heat pipe over operating in the non-heat-pipe mode. Three wavelength regions were observed. They are in the red, the green-blue, and the near ultraviolet regions. The absorption cross section depends on the wavelength of the incident light. Representative peak values for the v"=0 progression in the red and green-blue regions are 2.59 A sup 2 (average value) and 11.77 A sup 2 (T sub ave=624 K). The value for the C greater than X transitions is several tenths A sup 2. The cross sections were measured from absorption spectra taken as a function of temperature.

Fong, Zeng-Shevan↗