Search NASA⌕ Search

SEARCH · Search NASA

Results for “Crystalline properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2024

Revision 1: Characterizing Basalt-Atmosphere Interactions on Venus: A Review of Thermodynamic and Experimental Results

The surface of Venus is in contact with a hot (~470° C), high pressure (92 bars), and caustic (CO 2 with S, but little H 2 O) atmosphere, which should cause progressive alteration of the crust in the form of sulfate and iron-oxide coatings; however, the exact rate of alteration and mineral species are not well constrained. Different experimental approaches, each with its own limitations, are currently being used to constrain mineralogy and alteration rate. One note is that no experimental approach has been able to fully replicate the necessary conditions and sustain them for a significant length of time. Further, geochemical modeling studies can also constrain surface alteration mineralogy, again with different assumptions and limitations. Here we review recent geochemical modeling and experimental studies to constrain the state of the art for alteration mineralogy, rate of alteration, open questions about the surface mineralogy of Venus, and what can be constrained before the fleet of missions arrive later this decade. Combining the new results confirm that basalt on the surface of Venus should react quickly and form coatings of sulfates and iron-oxides; however, the mineralogy and rate of alteration is dependent on physical properties of the protolith (including bulk composition, mineralogy, and crystallinity), as well as atmospheric composition, and surface temperature. Importantly, the geochemically modelling results show that the mineralogy is largely controlled by atmospheric oxygen fugacity, which is not well constrained for the near surface environment on Venus. Therefore, alteration experiments run over a range of oxygen and sulfur fugacities are needed across a wide range of Venus analog materials with varying mineralogy and crystallinity.

Justin Filiberto↗
NASA NTRS1982

The effects of electron and gamma radiation on epoxy-based materials

Specimens of graphite/epoxy composites and epoxy resins were exposed to electron and gamma radiation, followed by mechanical property and fundamental measurements. Measurement techniques included: scanning electron microscopy, X-ray diffraction analysis, and electron spin resonance spectroscopic analysis. Results indicate little or no change in flexural properties of miniature specimens of a graphite/epoxy composite and no change in failure mode at the fiber-resin interface and in the crystallinity of the fiber and the resin. Some doubt in the observation of stable flexural properties is cast by electron paramagnetic resonance spectra of a relatively large number of radiation-generated radicals. These generally lead to a change in cross-linking and in chain-scissioning which should alter mechanical properties.

Fornes, R. E.↗
NASA NTRS2013

Castable Amorphous Metal Mirrors and Mirror Assemblies

A revolutionary way to produce a mirror and mirror assembly is to cast the entire part at once from a metal alloy that combines all of the desired features into the final part: optical smoothness, curvature, flexures, tabs, isogrids, low CTE, and toughness. In this work, it has been demonstrated that castable mirrors are possible using bulk metallic glasses (BMGs, also called amorphous metals) and BMG matrix composites (BMGMCs). These novel alloys have all of the desired mechanical and thermal properties to fabricate an entire mirror assembly without machining, bonding, brazing, welding, or epoxy. BMGs are multi-component metal alloys that have been cooled in such a manner as to avoid crystallization leading to an amorphous (non-crystalline) microstructure. This lack of crystal structure and the fact that these alloys are glasses, leads to a wide assortment of mechanical and thermal properties that are unlike those observed in crystalline metals. Among these are high yield strength, carbide-like hardness, low melting temperatures (making them castable like aluminum), a thermoplastic processing region (for improving smoothness), low stiffness, high strength-to-weight ratios, relatively low CTE, density similar to titanium alloys, high elasticity and ultra-smooth cast parts (as low as 0.2-nm surface roughness has been demonstrated in cast BMGs). BMGMCs are composite alloys that consist of a BMG matrix with crystalline dendrites embedded throughout. BMGMCs are used to overcome the typically brittle failure observed in monolithic BMGs by adding a soft phase that arrests the formation of cracks in the BMG matrix. In some cases, BMGMCs offer superior castability, toughness, and fatigue resistance, if not as good a surface finish as BMGs. This work has demonstrated that BMGs and BMGMCs can be cast into prototype mirrors and mirror assemblies without difficulty.

Hofmann, Douglas C.↗
NASA NTRS1990

Thermodynamic properties and crystallization kinetics at high liquid undercooling

The heat capacities of liquid and crystalline Au-Pb-Sb alloys in the glass-forming composition range were measured with droplet emulsion and bulk samples. Based on the measured C(sub p) data, the entropy, enthalpy, and Gibbs free energy functions of the eutectic, solid mixture, and undercooled liquid were determined as a function of undercooling and compared with theoretical predictions. The results indicate an isentropic temperature at 313 + or - 5 K, which agrees well with experimental data for the glass transition. A kinetics analysis of the nucleation undercooling response suggests that the proper choice for the Gibbs free energy change during crystallization is most important in analyzing the nucleation kinetics. By classical nucleation theory, the prefactors obtained, based on a variety of theoretical predictions for the driving force, can differ by six orders of magnitude. If the nucleation rates are extrapolated to high undercooling, the extrapolations based on measured heat capacity data show agreement, whereas the predicted nucleation rates are inconsistent with results from drop tower experiments. The implications for microg experiments are discussed.

Fecht, Hans J.↗
NASA NTRS1996

Evaluation of Student Outcomes in Materials Science and Technology

This paper specifies 14 benchmarks and exit standards for the introduction of Materials Science and Technology in a secondary school education. Included is the standard that students should be able to name an example of each category of technological materials including metals, glass/ceramics, polymers (plastics) and composites. Students should know that each type of solid material has specific properties that can be measured. Students will learn that all solid materials have either a long range crystalline structure or a short range amorphous structure (i.e., glassy). They should learn the choice of materials for a particular application depends on the properties of the material, and the properties of the material depends on its crystal structure and microstructure. The microstructure may be modified by the methods by which the material is processed; students should explain this by the example of sintering a ceramic body to reduce its porosity and increase its densification and strength. Students will receive exposure to the world of work, post secondary educational opportunities, and in general a learning that will lead to a technologically literate intelligent citizen.

Piippo, Steven↗
NASA NTRS1972

PTFE films with improved flexibility

Development and application of flexible polytetrafluroethylene films for expulsion bladders in spacecraft propellant tanks are described. Flexibility of material is obtained by reducing crystallinity through annealing and quenching in water. Physical and mechanical properties of material are presented.

Muraca, R. F.↗
NASA NTRS1991

Synthesis of imide/arylene ether copolymers for adhesives and composite matrices

A series of imide/arylene ether copolymers were prepared from the reaction of an amorphous arylene ether oligomer and a semi-crystalline imide oligomer. These copolymers were thermally characterized and mechanical properties were measured. One block copolymer was endcapped and the molecular weight was controlled to provide a material that displayed good compression moldability and attractive adhesion and composite properties.

Jensen, B. J.↗
NASA NTRS1974

Magnetic properties of Apollo 16 samples and implications for their mode of formation

The Apollo 16 crystalline rocks have a greater average percentage of metallic iron than any other lunar material and are the most reduced in terms of their metallic iron/total iron ratio. They have greater metal content than the mare basalts, the only primary igneous rocks on the moon, and more iron metal than the associated Apollo 16 breccias and soils. This fact and the relatively coarse grain size suggest reduction of the iron during the formation of the crystalline rocks, probably during melts and partial melts in an impact base surge deposit.

Pearce, G. W.↗
NASA NTRS1992

Chemistry and properties of poly(arylene ether benzoxazole)s

Several new poly(arylene ether benzoxazole)s (PAEBs) were prepared by the nucleophilic displacement reaction of activated aromatic difluorides with two novel bis(hydroxyphenyl benzoxazole), using potassium carbonate. The 6F-containing PAEBs exhibited better solubility and higher Tgs than did the 6,6'-bis-(2-(4-hydroxyphenyl)benzoxazole)-derived polymers. Several of the 6,6'bis(2-(4-hydroxyphenyl)benzoxazole)-derived polymers exhibited crystallinity by DSC and wide-angle X-ray diffraction. Unorientated thin film properties of the 6F-containing PAEBs were comparable to those of other 6F-containing PAEBS that were previously reported. The chemistry and the physical and mechanical properties of the above polymers are discussed.

Smith, J. G., Jr.↗
NASA NTRS2008

Optical Pressure-Temperature Sensor for a Combustion Chamber

A compact sensor for measuring temperature and pressure in a combusti on chamber has been proposed. The proposed sensor would include two optically birefringent, transmissive crystalline wedges: one of sapph ire (Al2O3) and one of magnesium oxide (MgO), the optical properties of both of which vary with temperature and pressure. The wedges wou ld be separated by a vapor-deposited thin-film transducer, which wou ld be primarily temperaturesensitive (in contradistinction to pressur e- sensitive) when attached to a crystalline substrate. The sensor w ould be housed in a rugged probe to survive the extreme temperatures and pressures in a combustion chamber.

Wiley, John↗
NASA NTRS1986

Composition, structure and chemistry of interstellar dust

The observational constraints on the composition of the interstellar dust are analyzed. The dust in the diffuse interstellar medium consists of a mixture of stardust (amorphous silicates, amorphous carbon, polycyclic aromatic hydrocarbons, and graphite) and interstellar medium dust (organic refractory material). Stardust seems to dominate in the local diffuse interstellar medium. Inside molecular clouds, however, icy grain mantles are also important. The structural differences between crystalline and amorphous materials, which lead to differences in the optical properties, are discussed. The astrophysical consequences are briefly examined. The physical principles of grain surface chemistry are discussed and applied to the formation of molecular hydrogen and icy grain mantles inside dense molecular clouds. Transformation of these icy grain mantles into the organic refractory dust component observed in the diffuse interstellar medium requires ultraviolet sources inside molecular clouds as well as radical diffusion promoted by transient heating of the mantle. The latter process also returns a considerable fraction of the molecules in the grain mantle to the gas phase.

Tielens, Alexander G. G. M.↗
NASA NTRS2005

Synthesis of GEMS from Shock-accelerated Crystalline Dust in Superbubbles: Model and Predictions

GEMS (Glass Embedded with Metals and Sulfides) are highly enigmatic yet common components of anhydrous IDPs. We have recently proposed a model of GEMS formation from shock-accelerated crystalline dust in superbubbles[1] which explains the three most perplexing properties of GEMS: pseudomorphism[2], their chemistry[3], and their size range. In this Abstract, we briefly review the main points of the model, and suggest tests that will either prove or rule out this hypothesis.

Westphal, Andrew J.↗
NASA NTRS1986

High efficiency crystalline silicon solar cells

A review of the entire research program since its inception ten years ago is given. The initial effort focused on the effects of impurities on the efficiency of silicon solar cells to provide figures of maximum allowable impurity density for efficiencies up to about 16 to 17%. Highly accurate experimental techniques were extended to characterize the recombination properties of the residual imputities in the silicon solar cell. A numerical simulator of the solar cell was also developed, using the Circuit Technique for Semiconductor Analysis. Recent effort focused on the delineation of the material and device parameters which limited the silicon efficiency to below 20% and on an investigation of cell designs to break the 20% barrier. Designs of the cell device structure and geometry can further reduce recombination losses as well as the sensitivity and criticalness of the fabrication technology required to exceed 20%. Further research is needed on the fundamental characterization of the carrier recombination properties at the chemical impurity and physical defect centers. It is shown that only single crystalline silicon cell technology can be successful in attaining efficiencies greater than 20%.

Sah, C. Tang↗
NASA NTRS2017

IR Spectra and Properties of Solid Acetone, an Interstellar and Cometary Molecule

Mid-infrared spectra of amorphous and crystalline acetone are presented along with measurements of the refractive index and density for both forms of the compound. Infrared band strengths are reported for the first time for amorphous and crystalline acetone, along with IR optical constants. Vapor pressures and a sublimation enthalpy for crystalline acetone also are reported. Positions of (sup 13) C-labeled acetone are measured. Band strengths are compared to gas-phase values and to the results of a density-functional calculation. A 73 percent error in previous work is identified and corrected.

ethers↗
NASA NTRS2017

IR Spectra and Properties of Solid Acetone, an Interstellar and Cometary Molecule

Mid-infrared spectra of amorphous and crystalline acetone are presented along with measurements of the refractive index and density for both forms of the compound. Infrared band strengths are reported for the first time for amorphous and crystalline acetone, along with IR optical constants. Vapor pressures and a sublimation enthalpy for crystalline acetone also are reported. Positions of 13C-labeled acetone are measured. Band strengths are compared to gas-phase values and to the results of a density-functional calculation. A 73% error in previous work is identified and corrected.

IR spectroscopy, band strengths, astrochemistry, a↗