Search NASA⌕ Search

SEARCH · Search NASA

Results for “DAMPING IN ROLL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1954

A study of the problem of designing airplanes with satisfactory inherent damping of the dutch roll oscillation

Considerable interest has recently been shown in means of obtaining satisfactory stability of the dutch roll oscillation for modern high-performance airplanes without resort to complicated artificial stabilizing devices. One approach to this problem is to lay out the airplane in the earliest stages of design so that it will have the greatest practicable inherent stability of the lateral oscillation. The present report presents some preliminary results of a theoretical analysis to determine the design features that appear most promising in providing adequate inherent stability. These preliminary results cover the case of fighter airplanes at subsonic speeds. The investigation indicated that it is possible to design fighter airplanes to have substantially better inherent stability than most current designs. Since the use of low-aspect-ratio swept-back wings is largely responsible for poor dutch roll stability, it is important to design the airplane with the maximum aspect ratio and minimum sweep that will permit attainment of the desired performance. The radius of gyration in roll should be kept as low as possible and the nose-up inclination of the principal longitudinal axis of inertia should be made as great as practicable. (author)

Campbell, John P↗
NASA NTRS1973

Model support roll balance and roll coupling

The design concepts of two specialized wind tunnel model support mechanisms are described. The forced oscillation roll balance mechanism was designed to meet the specific requirement to measure aerodynamic forces and moments to permit determination of the damping-in-roll parameters of winged configurations. A variable speed motor is used to oscillate the model by means of an offset crank. The oscillating motion is resisted by a torsion spring to provide a restoring torque and is attached to the section forward of the strain-gage balance. This spring action allows the model to be oscillated at a frequency for velocity resonance, whereby the mechanical spring and any aerodynamic spring balance. This spring action allows the model to be oscillated at a frequency for velocity resonance, whereby the mechanical spring and any aerodynamic spring balance out the model inertia. The only torque then required to oscillate the model at that particular frequency is equal to that due to aerodynamic damping. The second mechanism, a roll coupling for remotely rotating a model, was designed to invert or roll a model about its longitudinal axis when mounted for testing.

Sharpes, R. E.↗
NASA NTRS1950

Some theoretical low-speed span loading characteristics of swept wings in roll and sideslip

The Weissinger method for determining additional span loading for incompressible flow is used to find the damping in roll, the lateral center of pressure of the rolling for wing plan forms of various aspect ratios, taper ratios, and sweep angles. In addition, the applicability of the method to the determination of certain other aerodynamic derivatives is investigated, and corrections for the first-order effects of compressibility are indicated. The agreement obtained between experimentally and theoretically determined values for the aerodynamic coefficients indicates that the method of Weissinger is well suited to the calculation of such resulting aerodynamic derivatives of wings as do not involve considerations of tip suction.

Bird, John D↗
NASA NTRS2012

Vibration Propagation of Gear Dynamics in a Gear-Bearing-Housing System Using Mathematical Modeling and Finite Element Analysis

Vibration and noise caused by gear dynamics at the meshing teeth propagate through power transmission components to the surrounding environment. This study is devoted to developing computational tools to investigate the vibro-acoustic propagation of gear dynamics through a gearbox using different bearings. Detailed finite element/contact mechanics and boundary element models of the gear/bearing/housing system are established to compute the system vibration and noise propagation. Both vibration and acoustic models are validated by experiments including the vibration modal testing and sound field measurements. The effectiveness of each bearing type to disrupt vibration propagation is speed-dependent. Housing plays an important role in noise radiation .It, however, has limited effects on gear dynamics. Bearings are critical components in drivetrains. Accurate modeling of rolling element bearings is essential to assess vibration and noise of drivetrain systems. This study also seeks to fully describe the vibro-acoustic propagation of gear dynamics through a power-transmission system using rolling element and fluid film wave bearings. Fluid film wave bearings, which have higher damping than rolling element bearings, could offer an energy dissipation mechanism that reduces the gearbox noise. The effectiveness of each bearing type to disrupt vibration propagation in explored using multi-body computational models. These models include gears, shafts, rolling element and fluid film wave bearings, and the housing. Radiated noise is mapped from the gearbox surface to surrounding environment. The effectiveness of rolling element and fluid film wave bearings in breaking the vibro-acoustic propagation path from the gear to the housing is investigated.

Parker, Robert G.↗
NASA NTRS1972

Stability and control of externally blown flap configurations

The results of wind-tunnel investigations on the stability and control characteristics of externally blown jet-flap configurations are presented. Conventional wind-tunnel tests and free-flight model tests have shown that longitudinal trim and stability can be achieved by a properly located horizontal tail of sufficient size, and that lateral trim in the engine-out condition can be produced by combinations of differential flap, spoiler, and rudder deflection. Free-flight model tests have revealed a lightly damped Dutch roll lateral oscillation, and have shown that the oscillation can be stabilized by use of artificial damping.

Parlett, L. P.↗
NASA NTRS1991

Modeling, simulation, and flight characteristics of an aircraft designed to fly at 100,000 feet

A manned real time simulation of a conceptual vehicle, the stratoplane, was developed to study the problems associated with the flight characteristics of a large, lightweight vehicle. Mathematical models of the aerodynamics, mass properties, and propulsion system were developed in support of the simulation and are presented. The simulation was at first conducted without control augmentation to determine the needs for a control system. The unaugmented flying qualities were dominated by lightly damped dutch roll oscillations. Constant pilot workloads were needed at high altitudes. Control augmentation was studied using basic feedbacks. For the longitudinal axis, flight path angle, and pitch rate feedback were sufficient to damp the phugoid mode and to provide good flying qualities. In the lateral directional axis, bank angle, roll rate, and yaw rate feedbacks were sufficient to provide a safe vehicle with acceptable handling qualities. Intentionally stalling the stratoplane to very high angles of attack (deep stall) was studied as a means of enable safe and rapid descent. It was concluded that the deep stall maneuver is viable for this class of vehicle.

Sim, Alex G.↗
NASA NTRS1978

Characteristics of an Air Cushion Landing System incorporating an inelastic trunk

A series of static and dynamic tests performed on an Air Cushion Landing System (ACLS) incorporating inelastic trunk are described. The tests were performed on an apparatus which had provisions to isolate heave-pitch and roll motion on the prototype cushion. The results of the test show that the sides of the trunk behave differently from the trunk ends. The tests also demonstrate that the current ACLS designs suffer from low heave damping, low roll stiffness and fan stall problems.

Boghani, A. B.↗
NASA NTRS1953

Wind-tunnel investigation of the effects of steady rolling on the aerodynamic loading characteristics of a 45 degree sweptback wing at high subsonic speeds

An investigation has been conducted in the Langley high- speed 7- by 10-foot tunnel to determine the effect of steady rolling on the aerodynamic loading characteristics of a 45° sweptback wing of aspect ratio 4 in combination with a fuselage. The investigation covered Mach numbers of 0.70, 0.85, and 0.91 at angles of attack up to 13°. The r esults indicate that the loss in damping in roll previously noted for this wing is due to stalling of the tip sections. The effects of rolling velocity on the span load distrib~tion can be satisfactorily estimated if measured pressure-distribution data in pitch are available.

James W Wiggins↗
NASA NTRS1992

Forebody vortex control for suppressing wing rock on a highly-swept wing configuration

Free-to-roll tests were conducted in a wind tunnel with a configuration that consisted of a highly-slender forebody and a 78 deg swept delta wing. A limit cycle oscillation was observed for angles of attack between 22 and 30 deg. In general, the main flow phenomena responsible for the wing-body-tail wing rock are the interactions between the forebody and the wing vortices. Various blowing techniques were evaluated as means of wing rock suppression. Blowing tangentially aft from leeward side nozzles near the forebody tip can damp the roll motion at low blowing rates and stop it completely at higher blowing rates. At the high rates, significant vortex asymmetries are created, causing the model to stop at a non-zero roll angle. Forward blowing and alternating right/left pulsed blowing appear to be more efficient techniques for suppressing wing rock. The oscillations can be damped almost completely at lower blowing coefficients, and, apparently, no major vortex asymmetries are induced. Good agreement is observed between this study and previous water tunnel tests on the same configuration.

Suarez, Carlos J.↗
NASA NTRS2019

Subsonic Dynamic Testing of a Subscale ADEPT Entry Vehicle

The Adaptive Deployable Entry and Placement Technology (ADEPT) is a mechanically-deployed entry system. A sounding rocket test flight of an ADEPT vehicle, known as ADEPT SR-1, was conducted in September 2018. Prior to this sounding rocket test, an investigation was performed using the NASA Langley Research Center 20-ft Vertical Spin Tunnel (VST) to assess the free-flight dynamic characteristics of ADEPT SR-1 at subsonic speeds. The model of ADEPT SR-1 for this VST test was fabricated at 50-percent geometric scale, with dynamically scaled mass properties (Froude scaled) to represent full-scale flight at an altitude of 1.2 km above sea level. The subsonic dynamic characteristics of ADEPT SR-1 were of interest prior to the sounding rocket test because of payload recovery considerations. At low roll rates the model was found to have acceptable dynamic characteristics. It was statically stable in pitch and yaw, exhibiting limit cycle pitch/yaw oscillations of no greater than 20 degrees (the angle between the model’s longitudinal axis and nadir). The model was able to recover from large upsets in pitch and yaw, although if sufficiently provoked it tumbled. Damping in roll was low. At high roll rates the pitch and yaw oscillations grew in magnitude and rate. This behavior was also observed during the sounding rocket flight test.

Cruz, Juan R.↗
NASA NTRS1987

Analysis of lateral stability of X-29 drop model using system identification methodology

A 22-percent dynamically scaled replica of the X-29 forward-swept-wing aircraft is currently being flown in radio-controlled drop tests at NASA Langley's Plumtree Test Site. Flight data were recorded from early flights in the test program, which consisted mainly of large amplitude maneuvers over wide angle-of-attack ranges with several uncontrolled wing rock episodes. A system identification study of the recorded data was undertaken to examine the stability and control derivatives which influence the lateral behavior of this vehicle with particular emphasis on the wing rock phenomenon. All major lateral stability derivatives and the damping-in-roll derivative were identified for 5-80 deg angle-of-attack by using a data partitioning methodology and a modified stepwise regression algorithm. No control effectiveness derivatives could be identified from the flights conducted so far.

Raney, David L.↗
NASA NTRS1989

Lateral stability analysis for X-29A drop model using system identification methodology

A 22-percent dynamically scaled replica of the X-29A forward-swept-wing airplane has been flown in radio-controlled drop tests at the NASA Langley Research Center. A system identification study of the recorded data was undertaken to examine the stability and control derivatives that influence the lateral behavior of this vehicle with particular emphasis on an observed wing rock phenomenon. All major lateral stability derivatives and the damping-in-roll derivative were identified for angles of attack from 5 to 80 degrees by using a data-partitioning methodology and a modified stepwise regression algorithm.

Raney, David L.↗
NASA NTRS1992

Aerodynamic parameters of the X-31 drop model estimated from flight-data at high angles of attack

Lateral aerodynamic parameters of the X-31 drop model were estimated from flight data at angles of attack between 25 deg and 45 deg. Partitioned data from an ensemble of 12 maneuvers and data from 13 single maneuvers were analyzed by a stepwise regression technique to obtain an aerodynamic model structure and least squares parameter estimates. Because of data collinearity in several maneuvers, these maneuvers were reanalyzed by two biased estimation techniques, mixed estimation and fractional rank regression. The final parameter estimates in the form of stability and control derivatives were plotted against the angle of attack and compared with wind tunnel results and a limited number of estimates from full-scale aircraft data. There was no significant disagreement between parameters from the two sets of drop model data and the full-scale aircraft data. Some differences, however, existed between the dihedral, damping-in-roll, and aileron-effectiveness parameters from flight and wind tunnel data.

Klein, Vladislav↗
NASA NTRS1953

A Flight Study of the Effects on Tracking Performance of Changes in the Lateral-oscillatory Characteristics of a Fighter Airplane

A study of the effects of variations in lateral-oscillatory characteristics on air-to-air tracking performance has been made, using a conventional, propeller-driven fighter airplane equipped with servo devices for varying these characteristics in flight. Tracking runs were made both in smooth air and in simulated rough air. The lateral-oscillation period, damping, and roll coupling were varied over wide ranges during the investigation.

GUSTS, TURBULENCE↗
NASA NTRS1954

A Free-flight Wind Tunnel for Aerodynamic Testing at Hypersonic Speeds

The supersonic free-flight wind tunnel is a facility at the Ames Laboratory of the NACA in which aerodynamic test models are gun-launched at high speed and directed upstream through the test section of a supersonic wind tunnel. In this way, test Mach numbers up to 10 have been attained and indications are that still higher speeds will be realized. An advantage of this technique is that the air and model temperatures simulate those of flight through the atmosphere. Also the Reynolds numbers are high. Aerodynamic measurements are made from photographic observation of the model flight. Instruments and techniques have been developed for measuring the following aerodynamic properties: drag, initial lift-curve slope, initial pitching-moment-curve slope, center of pressure, skin friction, boundary-layer transition, damping in roll, and aileron effectiveness. (author)

Seiff, Alvin↗
NASA NTRS1953

A Vector Study of Linearized Supersonic Flow Applications to Nonplanar Problems

A vector study of the partial-differential equation of steady linearized supersonic flow is presented. General expressions which relate the velocity potential in the stream to the conditions on the disturbing surfaces, are derived. In connection with these general expressions the concept of the finite part of an integral is discussed. A discussion of problems dealing with planar bodies is given and the conditions for the solution to be unique are investigated. Problems concerning nonplanar systems are investigated, and methods are derived for the solution of some simple nonplanar bodies. The surface pressure distribution and the damping in roll are found for rolling tails consisting of four, six, and eight rectangular fins for the Mach number range where the region of interference between adjacent fins does not affect the fin tips.

Martin, John C↗
NASA NTRS1994

Navier-Stokes prediction of large-amplitude forced and free-to-roll delta-wing oscillations

The three-dimensional Reynolds-averaged, Navier-Stokes (RANS) equations are used to numerically simulate nonsteady vortical flow about a 65 degree sweep delta wing at 30 degrees angle of attack. Two large-amplitude, high-rate, forced-roll motions and a damped free-to-roll motion are presented. The free-to-roll motion is computed by coupling the time-dependent RANS equations to the flight dynamic equation of motion. The computed results are compared with experimental forces, moments, and roll-angle time histories. The overall agreement is good. Vortex breakdown is present in each case, which causes significant time lags in the vortex breakdown motions relative to the body motions. This behavior strongly influences the dynamic forces and moments.

Chaderjian, Neal M.↗