Search NASA⌕ Search

SEARCH · Search NASA

Results for “Diamond”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1991

Selective and low temperature synthesis of polycrystalline diamond

Polycrystalline diamond thin films have been deposited on single-crystal silicon substrates at low temperatures (not above 600 C) using a mixture of hydrogen and methane gases by high-pressure microwave plasma-assisted chemical vapor deposition. Low-temperature deposition has been achieved by cooling the substrate holder with nitrogen gas. For deposition at reduced substrate temperature, it has been found that nucleation of diamond will not occur unless the methane/hydrogen ratio is increased significantly from its value at higher substrate temperature. Selective deposition of polycrystalline diamond thin films has been achieved at 600 C. Decrease in the diamond particle size and growth rate and an increase in surface smoothness have been observed with decreasing substrate temperature during the growth of thin films. As-deposited films are identified by Raman spectroscopy, and the morphology is analyzed by scanning electron microscopy.

Ramesham, R.↗
NASA NTRS1991

Implanted He-3, He-4, and Xe in further studies of diamonds from Western Australia

In measurements of the noble gases in additional samples of diamonds from the Argyle and Ellendale lamproites in Western Australia, no neon-rich stones were encountered. No neon was detected above the relatively high blank levels in the glass apparatus. White and brown diamonds showed no differences in noble gas content, nor did samples segregated by the color of long-wave UF fluorescence. The rare gas patterns in the 1.2 Ga Argyle pipe are largely consistent with implanted He-3, He-4, and fissiogenic Xe from U/Th in the matrix rock in which the diamonds have been stored for so long. These implanted species are absent in diamonds from the much younger (about 20 Ma) Ellendale pipe. Implantation formulas for several models of inhomogeneously distributed U/Th are given. Differences in He-3 content between pipe and alluvial Argyle samples are consistent with expected cosmogenic production in the latter. An expanded data base for helium and carbon isotopic data on the same samples supports a negative (He-4)-delta(C-13) correlation seen in earlier work.

Mcconville, P.↗
NASA NTRS1993

Electrical Conductivity Of Diamond Up To 1,200 Degrees C

Report discusses measurements of electrical conductivities of two synthetic diamond films, three synthetic diamondlike films, and two natural type IIa diamonds at temperatures from ambient to 1,200 degrees C. Measurements performed to compare electrical conductivities of state-of-the-art diamond films with those of natural insulating diamond, particularly at temperatures above 700 degrees C.

Vandersande, Jan W.↗
NASA NTRS1993

Electrochemical patterning of amorphous carbon on diamond

The ability to pattern ion-implantation damaged or other nondiamond carbon on a diamond substrate is useful for fabricating a variety of devices. We accomplished such patterning by an unmasked implantation into a diamond substrate followed by photolithography and a selective electrochemical etch. The use of a high resistivity medium coupled with applied biases over 50 V permitted etching without requiring contact between the substrate and an electrode. Many electrolytes gave etches that exhibit high selectivity for nondiamond carbon over both diamond and dielectrics such as photoresist. Optical, electrical, and Raman spectroscopic measurements elucidate the effects of the etch on the implanted diamond surface.

Marchywka, Mike↗
NASA NTRS1993

Diamonds in dense molecular clouds - A challenge to the standard interstellar medium paradigm

Observations of a newly discovered infrared C-H stretching band indicate that interstellar diamond-like material appears to be characteristic of dense clouds. In sharp contrast, the spectral signature of dust in the diffuse interstellar medium is dominated by -CH2- and -CH3 groups. This dichotomy in the aliphatic organic component between the dense and diffuse media challenges standard assumptions about the processes occurring in, and interactions between, these two media. The ubiquity of this interstellar diamond-like material rules out models for meteoritic diamond formation in unusual circumstellar environments and implies that the formation of the diamond-like material is associated with common interstellar processes or stellar types.

Allamandola, L. J.↗
NASA NTRS1991

High quality flame deposited diamond films for infrared optical windows

The IR absorption in polycrystalline diamond films deposited in oxygen-acetylene flames is characterized using FTIR. The one-phonon absorption coefficient in the region from 7 to 12 microns that is related to extrinsic defects in the diamond films shows a strong dependence on the flame conditions as well as the substrate temperature. A high degree of diamond crystalline perfection, as judged from the undetectable one-phonon absorption, is achieved under the optimized deposition conditions for our flame setup. This is further supported by the sharp Raman peak at 1332/cm as well as the high purity in crystal orientation according to the X-ray diffraction pattern measured for the high quality diamond films.

Tzeng, Y.↗
NASA NTRS1993

Classification of multispectral image data by the Binary Diamond neural network and by nonparametric, pixel-by-pixel methods

The classification of multispectral image data obtained from satellites has become an important tool for generating ground cover maps. This study deals with the application of nonparametric pixel-by-pixel classification methods in the classification of pixels, based on their multispectral data. A new neural network, the Binary Diamond, is introduced, and its performance is compared with a nearest neighbor algorithm and a back-propagation network. The Binary Diamond is a multilayer, feed-forward neural network, which learns from examples in unsupervised, 'one-shot' mode. It recruits its neurons according to the actual training set, as it learns. The comparisons of the algorithms were done by using a realistic data base, consisting of approximately 90,000 Landsat 4 Thematic Mapper pixels. The Binary Diamond and the nearest neighbor performances were close, with some advantages to the Binary Diamond. The performance of the back-propagation network lagged behind. An efficient nearest neighbor algorithm, the binned nearest neighbor, is described. Ways for improving the performances, such as merging categories, and analyzing nonboundary pixels, are addressed and evaluated.

Salu, Yehuda↗
NASA NTRS1993

The carbon isotopic composition of Novo Urei diamonds

The carbon isotopic composition of diamond grains isolated from the Novo Urei meteorite are discussed. A diamond separate was obtained from 2g of whole rock using the chemical treatments described aimed at obtaining very pure diamond. X ray diffraction of the residue, which represented 5000 ppm of the parent mass, indicated only the presence of the desired mineral. The diamond crystals were 1-30 microns in diameter, and some grains had a yellow color. The chemical treatments were followed by a size separation to give a 1-10 microns and a 5-30 microns fraction, which were named DNU-1 and DNU-2, respectively.

Fisenko, A. V.↗
NASA NTRS1993

Robust stability of diamond families of polynomials with complex coefficients

Like the interval model of Kharitonov, the diamond model proves to be an alternative powerful device for taking into account the variation of parameters in prescribed ranges. The robust stability of some kinds of diamond polynomial families with complex coefficients are discussed. By exploiting the geometric characterizations of their value sets, we show that, for the family of polynomials with complex coefficients and both their real and imaginary parts lying in a diamond, the stability of eight specially selected extreme point polynomials is necessary as well as sufficient for the stability of the whole family. For the so-called simplex family of polynomials, four extreme point and four exposed edge polynomials of this family need to be checked for the stability of the entire family. The relations between the stability of various diamonds are also discussed.

Xu, Zhong Ling↗
NASA NTRS1995

Diamond and diamondlike carbon as wear-resistant, self-lubricating coatings for silicon nitride

Recent work on the friction and wear properties of as-deposited fine-grain diamond, polished coarse-grain diamond, and as-deposited diamondlike carbon (DLC) films in humid air at a relative humidity of approximately 40 percent and in dry nitrogen is reviewed. Two types of chemical vapor deposition (CVD) processes are used to deposit diamond films on silicon nitride (Si3N4) substrates: microwave-plasma and hot-filament. Ion beams are used to deposit DLC films of Si3N4 substrates. The diamond and DLC films in sliding contact with hemispherical bare Si3N4 pins have low steady-state coefficients of friction (less than 0.2) and low wear rates (less than 10(exp -7) mm(exp 2)/N-m), and thus, can be used effectively as wear-resistant, self-lubricating coatings for Si3N4 in the aforementioned two environments.

Miyoshi, Kazuhisa↗
NASA NTRS1997

Diamond Composite Films for Protective Coatings on Metals and Method of Formation

Composite films consisting of diamond crystallites and hard amorphous films such as diamond-like carbon, titanium nitride, and titanium oxide are provided as protective coatings for metal substrates against extremely harsh environments. A composite layer having diamond crystallites and a hard amorphous film is affixed to a metal substrate via an interlayer including a bottom metal silicide film and a top silicon carbide film. The interlayer is formed either by depositing metal silicide and silicon carbide directly onto the metal substrate, or by first depositing an amorphous silicon film, then allowing top and bottom portions of the amorphous silicon to react during deposition of the diamond crystallites, to yield the desired interlayer structure.

Ong, Tiong P.↗
NASA NTRS1959

Investigation at Mach Numbers of 0.20 to 3.50 of a Blended Diamond Wing and Body Combination of Sonic Design but with Low Wave-Drag Increase with Increasing Mach Number

A diamond wing and body combination was designed to have an area distribution which would result in near optimum zero-lift wave-drag coefficients at a Mach number of 1.00, and decreasing wave-drag coefficient with increasing Mach number up to near sonic leading-edge conditions for the wing. The airfoil section were computed by varying their shape along with the body radii (blending process) to match the selected area distribution and the given plan form. The exposed wing section had an average maximum thickness of about 3 percent of the local chords, and the maximum thickness of the center-line chord was 5.49 percent. The wing had an aspect ratio of 2 and a leading-edge sweep of 45 deg. Test data were obtained throughout the Mach number range from 0.20 to 3.50 at Reynolds numbers based on the mean aerodynamic chord of roughly 6,000,000 to 9,000,000. The zero-lift wave-drag coefficients of the diamond model satisfied the design objectives and were equal to the low values for the Mach number 1.00 equivalent body up to the limit of the transonic tests. From the peak drag coefficient near M = 1.00 there was a gradual decrease in wave-drag coefficient up to M = 1.20. Above sonic leading-edge conditions of the wing there was a rise in the wave-drag coefficient which was attributed in part to the body contouring as well as to the wing geometry. The diamond model had good lift characteristics, in spite of the prediction from low-aspect-ratio theory that the rear half of the diamond wing would carry little lift. The experimental lift-curve slope obtained at supersonic speeds were equal to or greater than the values predicted by linear theory. Similarly the other basic aerodynamic parameters, aerodynamic center position, and maximum lift-drag ratios were satisfactorily predicted at supersonic speeds.

Holdaway, George H.↗
NASA NTRS1999

Computational Study of Field Initiated Surface Reactions for Synthesis of Diamond and Silicon

This project involves using quantum chemistry to simulate surface chemical reactions in the presence of an electric field for nanofabrication of diamond and silicon. A field delivered by a scanning tunneling microscope (STM) to a nanometer scale region of a surface affects chemical reaction potential energy surfaces (PES) to direct atomic scale surface modification to fabricate sub-nanometer structures. Our original hypothesis is that the applied voltage polarizes the charge distribution of the valence electrons and that these distorted molecular orbitals can be manipulated with the STM so as to change the relative stabilities of the electronic configurations over the reaction coordinates and thus the topology of the PES and reaction kinetics. Our objective is to investigate the effect of applied bias on surface reactions and the extent to which STM delivered fields can be used to direct surface chemical reactions on an atomic scale on diamond and silicon. To analyze the fundamentals of field induced chemistry and to investigate the application of this technique for the fabrication of nanostructures, we have employed methods capable of accurately describing molecular electronic structure. The methods we employ are density functional theory (DFT) quantum chemical (QC) methods. To determine the effect of applied bias on surface reactions we have calculated the QC PESs in various applied external fields for various reaction steps for depositing or etching diamond and silicon. We have chosen reactions which are thought to play a role in etching and the chemical vapor deposition growth of Si and diamond. The PESs of the elementary reaction steps involved are then calculated under the applied fields, which we vary in magnitude and configuration. We pay special attention to the change in the reaction barriers, and transition state locations, and search for low energy reaction channels which were inaccessible without the applied bias.

Musgrave, Charles Bruce↗
NASA NTRS1998

Negative Electron Affinity Mechanism for Diamond Surfaces

The energy distribution of the secondary electrons for chemical vacuum deposited diamond films with Negative Electron Affinity (NEA) was investigated. It was found that while for completely hydrogenated diamond surfaces the negative electron affinity peak in the energy spectrum of the secondary electrons is present for any energy of the primary electrons, for partially hydrogenated diamond surfaces there is a critical energy above which the peak is present in the spectrum. This critical energy increases sharply when hydrogen coverage of the diamond surface diminishes. This effect was explained by the change of the NEA from the true type for the completely hydrogenated surface to the effective type for the partially hydrogenated surfaces.

Krainsky, I. L.↗
NASA NTRS2000

The Magnetic Properties Of Aggregate Polycrystalline Diamond: Implications For Carbonado Petrogenesis

Carbonados are a type of diamond, which are made up of many aggregrates of small crystalline diamonds or microdiamonds. The term "carbonado" comes from the Portuguese word carbonated. They are only found in sedimentary deposits in the Central African Republic (CAR) and the Bahia Province of Brazil. They were once the source of the world's supply of industrial diamonds. Their origin is uncertain but several mutually exclusive hypotheses have been proposed. This theories are: (1) extraterrestrial, that is they formed from the dust cloud of original solar nebulae; (2) produced by the high temperatures and pressures of the Earth's mantle; (3) or as the result of an extra-terrestrial impact into a carbon rich layer of sediment. Our study was done to further the understanding of their origin. We measured the magnetic properties on some twenty samples from the CAR. An earlier study was done on whole samples of carbonados and the "common" or kimberlitic diamond. Our work differed in that we started at the surface and subsequently removed the surface layers (by days of acid immersion) into the interior; measuring the magnetic properties at each interval. This procedure permits us to monitor the distribution of magnetic substances within the samples. Our results showed that the magnetic carriers are distributed on the surface including the open pores and that the carbonado interior is essentially non-magnetic. This result suggests that the initial formation environment was deficient in magnetic particles. Such a situation could indicate that their formation was the result of an extra-terrestrial body impacting carbon-rich sediment. Obviously, more work will be required on isotopic and chemical analyses before a more detailed ori-in can be determined.

Kleteschka, Gunther↗
NASA NTRS1999

Measurements and Diagnostics of Diamond Films and Coatings

The commercial potential of chemical-vapor-deposited (CVD) diamond films has been established and a number of applications have been identified through university, industry, and government research studies. This paper discusses the methodologies used for property measurement and diagnostic of CVD diamond films and coatings. Measurement and diagnostic techniques studied include scanning electron microscopy, transmission electron microscopy, atomic force microscopy, stylus profilometry, x-ray diffraction, electron diffraction, Raman spectroscopy, Rutherford backscattering, elastic recoil spectroscopy, and friction examination. Each measurement and diagnostic technique provides unique information. A combination of techniques can provide the technical information required to understand the quality and properties of CVD diamond films, which are important to their application in specific component systems and environments. In this study the combination of measurement and diagnostic techniques was successfully applied to correlate deposition parameters and resultant diamond film composition, crystallinity, grain size, surface roughness, and coefficient of friction.

Miyoshi, Kazuhisa↗
NASA NTRS2001

Proceedings of the Sixth Applied Diamond Conference/Second Frontier Carbon Technology Joint Conference (ADC/FCT 2001)

These are the Proceedings of the Sixth Applied Diamond Conference/Second Frontier Carbon Technology Joint Conference hosted by Auburn University from August 6 to 10, 2001. The diamond CVD process was first reported by Dr. Spitsyn in 1981 and Prof. S. Iijima reported his discovery of carbon nanotubes in 1991. In the past years, both diamond-related materials and novel carbon materials have attracted considerable interest by the scientific, technological, and industrial community. Many practical and commercial products of diamond materials are reported in these proceedings. A broad variety of applications of carbon nanotubes and novel carbons have also been explored and demonstrated. Having more than 200 invited and contributing papers by authors from over 20 countries for presentations at ADC/FCT 2001 clearly demonstrates that these materials, due to the combination of their superior properties, are both scientifically amazing and economically significant.

Tzeng, Y.↗
NASA NTRS2002

The Effects of Proton Radiation on the Structure of Diamond Films

Diamond possesses many of the sought after material properties desired in present day applications and is also quite radiation resistant. These characteristics make it an ideal candidate for insertion into MicroElectroMechanical Systems (MEMS) technologies, particularly for space-based applications. Most prior radiation studies investigated single crystal, bulk diamond specimens, not polycrystalline thin films. This investigation examined the microstructural effects of irradiating polycrystalline diamond films with various proton dosages (10(exp 15) - 10(exp 17) H+/sq cm). Scanning Electron Microscopy, micro-Raman Spectroscopy, and micro-X-ray Diffraction techniques were used to examine the effects as a function of depth. Strain values were calculated. Results indicate that the diamond lattice is retained, even at maximum irradiation levels. Polycrystalline silicon was also examined for comparative purposes.

Newton, Robert Lee↗