Search NASA⌕ Search

SEARCH · Search NASA

Results for “EIS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1996

Effects of Sonic Booms on Marine Mammals: Problem Review and Recommended Research

By flying the High-Speed Civil Transport (HSCT) exclusively over uninhabited areas and mo over water, human annoyance will be reduced to acceptable levels. However, this strategy will for HSCT proponents to contend with the potential effects of sonic booms on animals, particularly ma mammals. What follows is a summary of the environmental regulations that must be addressed, the scientific community's concerns about the potential effects of the HSCT, and recommendations fox research to address the most important concerns. The recommendations included herein are based both on existing scientific evidence and regulatory needs. One cannot over-emphasize the importance of obtaining the appropriate information prior to substantial public exposure. Recent controversies over other human-made acoustic sources in the ocean suggest that the HSCT will receive intense scrutiny. It seems certain that an Environmental Impact Statement (EIS) and Incidental Harassment Authorization (IHA) under the Marine Mammal Protection Act (MMPA) or its equivalent will be necessary.

Bowles, Ann E.↗
NASA NTRS1997

Corrosion Studies of Wrought and Cast NASA-23 Alloy

Corrosion studies were carried out for wrought and cast NASA-23 alloy using electrochemical methods. The scanning reference electrode technique (SRET), the polarization resistance technique (PR), and the electrochemical impedance spectroscopy (EIS) were employed. These studies corroborate the findings of stress corrosion studies performed earlier, in that the material is highly resistant to corrosion.

Danford, M. D.↗
NASA NTRS1997

The Corrosion Protection of Magnesium Alloy AZ31B

Corrosion rates for bare and coated Magnesium alloy AZ31B have been measured. Two coatings, Dow-23(Trademark) and Tagnite(Trademark), have been tested by electrochemical methods and their effectiveness determined. Electrochemical methods employed were the scanning reference electrode technique (SRET), the polarization resistance technique (PR) and the electrochemical impedance spectroscopy technique (EIS). In addition, general corrosion and stress corrosion methods were employed to examine the effectiveness of the above coatings in 90 percent humidity. Results from these studies are presented.

Danford, M. D.↗
NASA NTRS1998

Corrosion Studies of 2195 Al-Li Alloy and 2219 Al Alloy with Differing Surface Treatments

Corrosion studies of 2195 Al-Li and 2219 Al alloys have been conducted using the scanning reference electrode technique (SRET) and the polarization resistance (PR) technique. The SRET was used to study corrosion mechanisms, while corrosion rate measurements were studied with the PR technique. Plates of Al203 blasted, soda blasted and conversion coated 2219 Al were coated with Deft primer and the corrosion rates studied with the EIS technique. Results from all of these studies are presented.

Danford, M. D.↗
NASA NTRS1999

Product Structure, the Heart of Product Definition

This paper describes the LMMSS Product Definition System (PDS) philosophy and approach were the use of each item parts document or software can be traced to a specific end item (EI) serial/tail number of the product. It explains why a part-oriented approach to data organization and configuration management is required. The definition of part-oriented is that all appropriate product definition data products will be collected. Referenced and managed by their linkage/relationship to parts/items, The paper will touch upon how LMMSS store/controls product definition information under each project's top product designator in a two tiered approach. One tier for each product end item and another tier which contain/controls listings of drawings, documents. Specifications and standards that are required for hardware item definition.

DeHoog, C., Jr.↗
NASA NTRS1994

An Optics Free Spectrometer for the Extreme Ultraviolet

The optics-free spectrometer is a photon spectrometer. It provides the photon spectrum of a broadband source by converting photons of energy E into electrons of energy E', according to the Einstein relation, E' = E - Ei. E, is the ionization threshold of the gas target of interest (any of the rare gases are suitable) and E is the incoming photon energy. As is evident from the above equation, only a single order spectrum is produced throughout the energy range between the first and second ionization potentials of the rare gas used. Photons with energy above the second ionization potential produce two groups of electrons, but they are readily distinguished from each other. This feature makes this device extremely useful for determining the true spectrum of a continuum source or a many line source. The principle of operation and the laboratory results obtained with a representative configuration of the optics-free spectrometer are presented.

Judge, D. L.↗
NASA NTRS2001

Impacts of ENSO on the South American Summer Monsoon During 1997-1999

Using the National Center for Environmental Prediction (NCEP) Reanalysis, and CPC Merged Analysis Product (CMAP) rainfall, we have compared and contrasted the anomalies of the South American Summer Monsoon (SASM) during two extreme years of 1997/98 (EI Nino) and 1998/99 (La Nina). The results are assessed against a "canonical" ENSO response (CER) pattern for the SASM obtained from empirical mode decomposition based on a previous period (1980-1995). Overall, the SASM anomalies compare well with CER, but with some important differences. Anomalies occurring in the warm phase of the 1997-98 El Nino are very significant and robust, while those occurring in 1998/99 La Nina, appear to be reversed from 1997/98, but are relatively weak and less well-defined. The most pronounced signal in DJF 1997/98 is the development of drought conditions in northern Brazil, excessive rainfall over northern Peru and Ecuador, and over Uruguay and southern Brazil. The tropical rainfall anomalies are associated with the eastward shift of the Walker circulation, which is represented by pronounced low-level anomalous westerlies over the equatorial eastern Pacific and easterlies over northern Brazil. The easterlies are deflected sharply southeastward by the steep topography of the Andes, enhancing the low-level jet (LLJ) along the eastern foothills of the Andes near 15-20 S. The LLJ penetrates deep into the extratropics, yielding rainfall anomalies further poleward compared to CER. During DJF 1997/98, the eastward expansion of the warm tropospheric temperature over the Nino-3 region causes anomalous geopotential height to develop in the upper troposphere above the Altiplano, leading to a strengthened Bolivian High. An upper-tropospheric jet anomaly maximum is found over the subtropical continent near 30 S, due to increasing meridional gradient of tropospheric temperature, as well as teleconnection patterns linking the South Pacific and the South Atlantic. Consistent with the CER, the South Pacific High is weakened, and the South Atlantic High is strengthened in DJF 1997/98. However, rather than appearing as a coherent large scale signal over the entire Atlantic as in CER, the South Atlantic High anomalies in DJF 1997/98 split into two separate high pressure centers; one located south of the Amazon basin, and another over the southeastern South Atlantic. The former is induced as a Rossby-wave response by ENSO-Induced sinking motion over nor-them and eastern Brazil, and the latter may be associated with extratropical teleconnection signals. Anomalous convection observed over equatorial western Africa may also have contributed to the different circulation response over the Atlantic in DFJ 1997/99 compared to the CER. Comparison of the evolution of the SASM anomalies in 1997-99 with their corresponding annual cycles, suggest that the anomalies are phase-locked to and represent either enhancement or reduction of the annual variations. Results suggest that, from a system perspective the SASM was strengthened during the 1997/98 El Nino and weakened, albeit to a lesser extent, during the 1998/99 La Nina.

Lau, K.-M.↗
NASA NTRS1995

Soot Aerosol In The Atmosphere: Pole-to-Pole Distribution And Contributions by Aircraft

Interest in the distribution of black carbon (soot) aerosol (BCA) in the atmosphere is warranted for the following reasons: (1) BCA has the highest absorption cross section of any compound known, thus it can absorb solar radiation to cause atmospheric warming; (2) BCA is a strong adsorber of gases, thus it can catalyze heterogeneous chemical reactions to modify the chemical composition of the atmosphere; (3) If aircraft emission is the major source of atmospheric BCA, it can serve as an atmospheric tracer of aircraft exhaust. We collect BCA particles greater than or equal to 0.02 micrometer diameter by wires mounted on both the DC-8 and ER-2 aircraft. After return to the laboratory, the wires are examined with a field emission scanning electron microscope to identify BCA particles by their characteristic morphology. Typically, BCA exists in the atmosphere as small particles of complex morphology. The particle sizes at the source are measured in tens of Angstrom units; after a short residence time in the atmosphere, individual particles coalesce to loosely packed agglomerates of typical dimensions 0.01 to 0.1 micrometer. We approximate the size of each BCA aggregate by that of a sphere of equivalent volume. This is done by computing the volume of a sphere whose diameter is the mean between averaged minimum and maximum dimensions of the BCA particle. While this procedure probably underestimates the actual surface area, it permits us to compare BCA size distributions among themselves and with other types of aerosols. When statistically justified, we fit lognormal distributions to the data points to determine number concentrations, geometric mean radii, standard deviations, BCA surface areas and volumes. Results to date permit the following conclusions: (1) BCA concentration in the northern stratosphere averages 0.6 ng per cubic meters. This amount is one part in 10(exp 4) after a volcanic eruption (e.g., Pinatubo) increasing to about one percent during volcanic quiescence. In the northern troposphere, BCA concentration averages 3.2 ng per cubic meters, or 0.3 percent of the background aerosol. (2) Applying an BCA emission index EI(BCA)=5 x 10(exp -5), measured in the exhaust wake of a Concorde supersonic jet aircraft, to realistic estimates of fuel burnt by the current and projected fleets permits us to conclude that: (i) Most BCA in the northern stratosphere results from aircraft emissions; (ii) Most BCA in the northern troposphere results from other sources than aircraft; (iii) A projected supersonic fleet will increase the northern stratospheric BCA concentration by one order of magnitude, unless the emission index is substantially reduced. (3) A strong gradient between the northern and southern hemispheres indicates that mixing across the equator is greatly inhibited in relation to atmospheric residence times of BCA. (4) The single scatter albedo of BCA/"background" aerosol mixtures suggests a cooling effect for most of the globe; an exemption is the Arctic because of the high surface albedo of the snow/ice covered earth's surface.

Pueschel, R. F.↗
NASA NTRS1995

Pole-to-Pole Distribution of Stratospheric Black Carbon (Soot) Aerosol from Aircraft

The distribution of black carbon (soot) aerosol (BCA) in the atmosphere is of interest for several reasons: (1) Because BCA has the highest absorption cross section of any compound known, it can absorb solar radiation to cause atmospheric warming. (2) Because it is a strong adsorber of gases, it can catalyze heterogeneous reactions to change the chemical composition of the atmosphere.(3) If aircraft are a major source of BCA, it is an important tracer of aircraft emissions. Analysis for BCA of impactor samples from Arctic and Antarctic deployments, utilizing particle morphology of scanning electron microscopy images, permits the following conclusions: (1) The BCA concentration in the northern stratosphere varies between 0 and 2.6 ng m-3 averaging 0.6 ng/cu m. (2) This BCA loading is commensurate with estimated fuel consumptions in the stratosphere by the current commercial fleet and an emission index E=0.03 g BCA per kg fuel burnt which was measured in jet exhaust at al titude.Thus, most stratospheric BCA in the northern stratosphere results from aircraft emissions. The background BCA concentration in the southern stratosphere varies between 0 and 0.6 ng cu m averaging 0.1 ng/cu m. This strong meridional gradient implies that stratospheric BCA residence time- is shorter than are mixing times between hemispheres. Projected annual fuel consumption of a future supersonic commercial fleet is 7E13 g. This fleet would increase stratospheric BCA loadings by a factor of 2-3, because almost all fuel would be burnt above the tropopause. An improved EI(BCA) by a factor of ten would result in an increase of stratospheric BCA loadings by approximately 50 %.

Pueschel, R. F.↗
NASA NTRS2001

Low Emissions RQL Flametube Combustor Test Results

The overall objective of this test program was to demonstrate and evaluate the capability of the Rich-burn/Quick-mix/Lean-burn (RQL) combustor concept for HSR applications. This test program was in support of the Pratt & Whitney and GE Aircraft Engines HSR low-NOx Combustor Program. Collaborative programs with Parker Hannifin Corporation and Textron Fuel Systems resulted in the development and testing of the high-flow low-NOx rich-burn zone fuel-to-air ratio research fuel nozzles used in this test program. Based on the results obtained in this test program, several conclusions can be made: (1) The RQL tests gave low NOx and CO emissions results at conditions corresponding to HSR cruise. (2) The Textron fuel nozzle design with optimal multiple partitioning of fuel and air circuits shows potential of providing an acceptable uniform local fuel-rich region in the rich burner. (3) For the parameters studied in this test series, the tests have shown T3 is the dominant factor in the NOx formation for RQL combustors. As T3 increases from 600 to 1100 F, EI(NOx) increases approximately three fold. (4) Factors which appear to have secondary influence on NOx formation are P4, T4, infinity(sub rb), V(sub ref,ov). (5) Low smoke numbers were measured for infinity(sub rb) of 2.0 at P4 of 120 psia.

Chang, Clarence T.↗
NASA NTRS2003

Novel Ordered Crown Ether-Containing Polyimides for Ion Conduction

We report the synthesis and characterization of thermally-stable polyimides for use as battery and fuel cell electrolyte membranes. Dianhydrides used were 1,4,5,8- naphthalenetetracarboxylic dianhydride and/or 4,4'-(hexafluoroisopropylidene)diphthalic anhydride. Diamines used were anti-4,4-diaminodibenzo-l8-crown-6, 4,4'- diaminodibenzo-24-crown-8, 2,2-bis(4-aminophenyl)hexafluoropropane, and/or 2,5- diaminobenzenesulfonic acid. The polymers were characterized using electrochemical impedance spectroscopy (EIS), thermal analysis and X-ray diffraction. Polymers containing the hexafluoroisopropylidene (HFIP) group were soluble in common organic solvents, while polymers without the HFIP group were very poorly soluble. Sulfonation yields polymers that are sparingly soluble in aqueous base and/or methanol. Degree of sulfonation, determined by titration, was between one and three sulfonate groups per repeat unit. Proton conductivity was determined as a function of water content, with a maximum conductivity of l x 10(exp -2) per centimeter when fully hydrated. Crown ether-containing polymers exhibit a high degree of order that may be indicative of crown ether channel formation, which may facilitate Li(+) transport for use in battery membranes.

Irvin, Jennifer A.↗
NASA NTRS2004

Ethnic Differences in Bending Stiffness of the Ulna and Tibia

There is considerable information about the variations in bone mass associated with different opportunity to compare a mechanical property of bone in young college women of Caucasian, Hispanic and Asian descent who gave informed consent to participate in an exercise study. The subjects were sedentary, in good health, eumenorrheic, non-smokers and had body mass indices (BMI) less than 30. Measurements acquired were body weight, kg, and height, cm, calcaneal and wrist bone density, g/square cm (PIXI, Lunar GE) and bending stiffness (EI, Nm(exp 2)) in the ulna and tibia. E1 was determined non-invasively with an instrument called the Mechanical Response Tissue Analyzer (MRTA) that delivers a vibratory stimulus to the center of the ulna or tibia and analyzes the response curve based on the equation E1 = k(sub b) L(exp 3)/48 where k, is lateral bending stiffness, L is the length of the bone, E is Young's modulus of elasticity and I, the bending moment of inertia. The error of the test (CV) based on measurements of an aluminum rod with a known E1 was 4.8%, of calcaneal BMD, 0.54%, and of wrist bone density, 3.45%.

Arnaud, S. B.↗
NASA NTRS2004

Volume and Mass Estimation of Three-Phase High Power Transformers for Space Applications

Spacecraft historically have had sub-1kW(sub e), electrical requirements for GN&C, science, and communications: Galileo at 600W(sub e), and Cassini at 900W(sub e), for example. Because most missions have had the same order of magnitude power requirements, the Power Distribution Systems (PDS) use existing, space-qualified technology and are DC. As science payload and mission duration requirements increase, however, the required electrical power increases. Subsequently, this requires a change from a passive energy conversion (solar arrays and batteries) to dynamic (alternator, solar dynamic, etc.), because dynamic conversion has higher thermal and conversion efficiencies, has higher power densities, and scales more readily to higher power levels. Furthermore, increased power requirements and physical distribution lengths are best served with high-voltage, multi-phase AC to maintain distribution efficiency and minimize voltage drops. The generated AC-voltage must be stepped-up (or down) to interface with various subsystems or electrical hardware. Part of the trade-space design for AC distribution systems is volume and mass estimation of high-power transformers. The volume and mass are functions of the power rating, operating frequency, the ambient and allowable temperature rise, the types and amount of heat transfer available, the core material and shape, the required flux density in a core, the maximum current density, etc. McLyman has tabulated the performance of a number of transformers cores and derived a "cookbook" methodology to determine the volume of transformers, whereas Schawrze had derived an empirical method to estimate the mass of single-phase transformers. Based on the work of McLyman and Schwarze, it is the intent herein to derive an empirical solution to the volume and mass estimation of three-phase, laminated EI-core power transformers, having radiated and conducted heat transfer mechanisms available. Estimation of the mounting hardware, connectors, etc. is not included.

Kimnach, Greg L.↗
NASA NTRS2005

Engineering Ultimate Self-Protection in Autonomic Agents for Space Exploration Missions

NASA's Exploration Initiative (EI) will push space exploration missions to the limit. Future missions will be required to be self-managing as well as self-directed, in order to meet the challenges of human and robotic space exploration. We discuss security and self protection in autonomic agent based-systems, and propose the ultimate self-protection mechanism for such systems-self-destruction. Like other metaphors in Autonomic Computing, this is inspired by biological systems, and is the analog of biological apoptosis. Finally, we discus the role it might play in future NASA space exploration missions.

Sterritt, Roy↗
NASA NTRS1997

AFS and DFS Growth at JPL

The goal for EIS File Service is to develop and deploy a service which encourages all JPL employees and contractors to use DFS to effiently share files, publish web pages, & access tools.

AFS DFS↗
NASA NTRS2002

Improved performance and safety of lithium ion cells with the use of fluorinated carbonate-based electrolytes

There has been increasing interest in developing lithium-ion electrolytes that possess enhanced safety characteristics, while still able to provide the desired stability and performance. Toward this end, our efforts have been focused on the development of lithium-ion electrolytes which contain partially and fully fluorinated carbonate solvents. The advantage of using such solvents is that they possess the requisite stability demonstrated by the hydrocarbon-based carbonates, while also possessing more desirable physical properties imparted by the presence of the fluorine substituents, such as lower melting points, increased stability toward oxidation, and favorable SEI film forming Characteristics on carbon. Specifically, we have demonstrated the beneficial effect of electrolytes which contain the following fluorinated carbonate-based solvents: methyl 2,2,2-trifluoroethyl carbonate (MTFEC), ethyl-2,2,2 trifluoroethyl carbonate (ETFEC), propyl 2,2,2-trifluoroethyl carbonate (PTFEC), methyl-2,2,2,2',2',2' -hexafluoro-i-propyl carbonate (MHFPC), ethyl- 2,2,2,2',2',2' -hexafluoro-i-propyl carbonate (EHFPC), and di-2,2,2-trifluoroethyl carbonate (DTFEC). These solvents have been incorporated into multi-component ternary and quaternary carbonate-based electrolytes and evaluated in lithium-carbon and carbon-LiNio.8Coo.202 cells (equipped with lithium reference electrodes). In addition to determining the charge/discharge behavior of these cells, a number of electrochemical techniques were employed (i.e., Tafel polarization measurements, linear polarization measurements, and electrochemical impedance spectroscopy (EIS)) to further characterize the performance of these electrolytes, including the SEI formation characteristics and lithium intercalatiodde-intercalation kinetics. In addition to their evaluation in experimental cells, cyclic voltammetry (CV) and conductivity measurements were performed on select electrolyte formulations to further our understanding of the trends in stability and ionic mobility imparted by different alkyl substituents in linear carbonates.

li-ion batteries fluorinated carbonate electrolyte↗
NASA NTRS2002

Improved low temperature performance of lithium ion cells with quaternary carbonate-based electrolytes

In order to enable future missions involving the exploration of the surface of Mars with Landers and Rovers, NASA desires long life, high energy density rechargeable batteries which can operate well at very low temperature (down to 40(deg)C). Lithium-ion technology has been identified as being the most promising chemistry, due to high gravimetric and volumetric energy densities, as well as, long life characteristics. However, the state-of-art (SOA) technology is not sufficient to meet the needs of many applications that require excellent low temperature capabilities. To further improve this technology, work at JF'L has been focused upon developing electrolytes that result in lithium-ion cells with wider temperature ranges of operation. These efforts have led to the identification of a number of ternary and quaternary, all carbonate-based electrolytes that have been demonstrated to result in improved low temperature performance in experimental three-electrode MCMB carbon/LiNio.sCoo.zOz cells. A number of electrochemical characterization techniques were performed on these cells (i.e., Tafel polarization measurements, linear polarization measurements, and electrochemical impedance spectroscopy (EIS)) to further enhance our understanding of the performance limitations at low temperature. The most promising electrolyte formulations, namely 1 .O M LiPF6EC+DEC+DMC+EMC (1 : 1: 1 :2 v/v) and 1 .O M LiPF6 EC+DEC+DMC+EMC (1 : 1 : 1 :3 v/v), were incorporated into SAFT prototype DD-size (9 Ahr) lithium- cells for evaluation. A number of electrical tests were performed on these cells, including rate characterization as a function of temperature, cycle life characterization at different temperatures, as well as, many mission specific characterization test to determine their viability to enable future missions to Mars. Excellent performance was observed with the prototype DD-size cells over a wide temperature range (-50 to 4OoC), with high specific energy being delivered at very low temperatures (i.e, over 95 WHrKg being delivered at 40(deg)C using a C/10 discharge rate).

Li-ion low temperature electrolytes↗
NASA NTRS2003

Li-ion cells for terrestrial robots

SAFT prismatic wound 5 Ahr MP series cells were evaluated for potential application in a lithium ion battery designed for Tactical Mobile Robots (TMR). In order to satisfy battery design requirements, a 10 Ahr battery containing two parallel 8-cell strings was proposed. The proposed battery has a weight and volume of approximately 3.2kg and 1.6 liters, respectively. Cell qualification procedures include initial characterization, followed by charge/discharge cycling at 100% DOD with intermittent EIS measurements at various state of charge. Certain cells were also subjected to extreme operational temperatures for worst-case analysis. Excellent specific energy (>130 Whr/kg) was obtained with initial characterization cycles. Even at abusive thermal conditions, the cell capacity fade was less than Ahr after 300 cycles. Rate characterization showed good cell discharge behavior with minimal decrease in capacity. At various state of charge, impedance measurements suggest that the cathode play a more significant role in capacity. At various state of charge impedance measurements suggest that the cathode play a more significant role in capacity fade than the anode.

robots↗