SEARCH · Search NASA

Results for “FINNED BODY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1975

Error in temperature measurements due to conduction along the sensors

When a sensor is embedded in a solid body to measure its internal temperature, any conduction to or from its sensing element may cause the indicated temperature to be different from the true temperature. This paper describes an analysis of the error caused by conduction when there is an arbitrary temperature distribution in the body along the sensor. The sensor is modeled as a cylindrical fin and the appropriate conduction equation is solved. The solution gives a correction for the error which depends on such parameters as, depth of immersion, thermocouple wire and insulation properties, contact between the sensor and the body, and temperature distribution in the body. The latter may not be known, but the measured temperature distribution can be used as a first approximation. The corrected value can then be used to obtain a better estimate of the error. The results show good agreement with experimental observations.

Singh, B. S.↗

NASA NTRS1983

The evaluation of the rolling moments induced by wraparound fins

A possible reason is suggested for the induced rolling moments occurring on wraparound-fin configurations in subsonic flight at zero angle of attack. The subsonic potential flow over the configuration at zero incidence is solved numerically. The body is simulated by a distribution of sources along its axis, and the fins are described by a vortex-lattice method. It is shown that rolling moments can be induced on the antisymmetric fins by the radial flow generated at the base of the configuration, either over the converging separated wake, or over the diverging plume of a rocket motor.

Seginer, A.↗

NASA NTRS1983

The evaluation of the rolling moments induced by wraparound fins

Seginer, A.↗

NASA NTRS1996

Subsonic Aerodynamic Characteristics of a Circular Body Earth-to-Orbit Vehicle

A test of a generic reusable earth-to-orbit transport was conducted in the 7- by 10-Foot high-speed tunnel at the Langley Research Center at Mach number 0.3. The model had a body with a circular cross section and a thick clipped delta wing as the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center vertical fin, wingtip fins, and a nose-mounted vertical fin. The configuration was longitudinally stable about the estimated center-of-gravity position of 0.72 body length and had sufficient pitch-control authority for stable trim over a wide range of angle of attack, regardless of fin arrangement. The maximum trimmed lift/drag ratio for the aft center-fin configuration was less than 5, whereas the other configurations had values of above 6. The aft center-fin configuration was directionally stable for all angles of attack tested. The wingtip and nose fins were not intended to produce directional stability but to be active controllers for artificial stabilization. Small rolling-moment values resulted from yaw control of the nose fin. Large adverse rolling-moment increments resulted from tip-fin controller deflection above 13 deg angle of attack. Flow visualization indicated that the adverse rolling-moment increments were probably caused by the influence of the deflected tip-fin controller on wing flow separation.

Lepsch, Roger A., Jr.↗

NASA NTRS1959

Some Research on the Lift and Stability of Wing-Body Combinations

The present paper summarizes and correlates broadly some of the research results applicable to fin-stabilized ammunition. The discussion and correlation are intended to be comprehensive, rather than detailed, in order to show general trends over the Mach number range up to 7.0. Some discussion of wings, bodies, and wing-body interference is presented, and a list of 179 papers containing further information is included. The present paper is intended to serve more as a bibliography and source of reference material than as a direct source of design information.

Purser, Paul E.↗

NASA NTRS1950

Aerodynamic Characteristics of NACA RM-10 Missile in 8- by 6-foot Supersonic Wind Tunnel at Mach Numbers from 1.49 to 1.98 II : Presentation and Analysis of Force Measurements

Experimental investigation of aerodynamic forces acting on body of revolution (NACA RM-10 missile) with and without stabilizing fins was conducted at Mach numbers from 1.49 to 1.98 at angles of attack from 0 to 9 degrees and at Reynolds number of approximately 30,000,000. Comparison of experimental lift, drag, and pitching-moment coefficients and center of pressure location for body alone is made with linearized potential theory and a semiempirical method. Results indicate that aerodynamic characteristics were predicted more accurately by semiempirical method than by potential theory. Breakdown of measured drag coefficients into components of friction, pressure, and base-pressure drag is presented for body alone at zero angle of attack.

TAIL-BODY COMBINATIONS - MISSILES↗

NASA NTRS2004

The X-38 V-201 Fin Fold Actuation Mechanism

The X-38 Vehicle 201 (V-201) is a space flight prototype lifting body vehicle that was designed to launch to orbit in the Space Shuttle orbiter payload bay. Although the project was cancelled in May 2003, many of the systems were nearly complete. This paper will describe the fin folding actuation mechanism flight subsystems and development units as well as lessons learned in the design, assembly, development testing, and qualification testing. The two vertical tail fins must be stowed (folded inboard) to allow the orbiter payload bay doors to close. The fin folding actuation mechanism is a remotely or extravehicular activity (EVA) actuated single fault tolerant system consisting of seven subsystems capable of repeatedly deploying or stowing the fins.

Lupo, Christian↗

NASA NTRS1972

Space shuttle: Static aerodynamic characteristics and control effectiveness of two delta wing orbiter configurations (M equals 0.6 to 4.96)

Two 0.00325-scale models of a space shuttle orbiter were tested in trisonic wind tunnel to obtain force, static stability, and control effectiveness data by six component internal strain gauge balance. Two separate configurations were tested; however, the fuselage and basic wing were of one-piece construction. The configurations were varied by replacing the straight wing tip extensions with upswept wing tips. Directional stability was provided for one configuration by a centerline vertical tail. Due to the one-piece body/wing construction, no body-alone data were obtained. The effect of tip fins and vertical tail size were, however, investigated. Both configurations were tested over a Mach range of 0.6 to 4.96 with data taken at angles of attack from minus 4 deg to 60 deg and at angles of sideslip from minus 4 deg to 10 deg.

Ellis, R. R.↗

NASA NTRS1956

Calculation of the forces and moments on a slender fuselage and vertical fin penetrating lateral gusts

A theory is presented for calculating the variation with frequency of the lateral-force and yawing-moment coefficients due to sinusoidal side gusts passing over the profile of a simple fuselage-vertical-fin combination. The analysis is based on slender-body theory. The method considers the penetration effect of both fuselage and vertical tail in calculating side force and yawing moment due to side gusts, as opposed to a simple lag concept which considers the flow angle to be uniform over the configuration.

STABILITY, LATERAL AND DIRECTIONAL - DYNAMIC↗

NASA NTRS1994

Experimental study at low supersonic speeds of a missile concept having opposing wraparound tails

A wind-tunnel investigation has been performed at low supersonic speeds (at Mach numbers of 1.60, and 2.16) to evaluate the aerodynamic characteristics of a missile concept capable of being tube launched and controlled with a simple one-axis canard controller. This concept, which features an axisymmetric body with two planar canards and four wraparound tail fins arranged in opposing pairs, must be in rolling motion to be controllable in any radial plane with the planar canards. Thus, producing a constant rolling moment that is invariant with speed and attitude to provide the motion is desirable. Two tail-fin shaping designs, one shaved and one beveled, were evaluated for their efficiency in producing the needed rolling moments, and the results showed that the shaved fins were much more desirable for this task than the beveled fins.

Allen, Jerry M.↗

NASA NTRS1999

X-33 Liquid Hydrogen Tanks

The liquid hydrogen tank is a multi-lobe graphite/epoxy tank with integrally bonded, woven composite joints. The tanks are broken down into three major subgroups: aft dome/bulkhead, mid barrel section, and the forward dome/bulkhead. The vehicle uses two tanks (a left and right hand tank) as the "aft fuselage" of the vehicle, to react all body bending loads, landing gear loads, canted and vertical fin loads and air loads, as well as being used as the cryogenic fuel cells.

Adams, Andrew J.↗

NASA NTRS1979

Pressure and thermal distributions on wings and adjacent surfaces induced by elevon deflections at Mach 6

Surface pressure distributions and heat transfer distributions were obtained on wing half-models in regions where three dimensional separated flow effects are prominent. Unswept and 50 deg and 70 deg swept semispan wings were tested, for trailing-edge-elevon ramp angles of 0 deg, 10 deg, 20 deg, and 30 deg, with and without cylindrical and flat plate center bodies and with and without various wing-tip plates and fins. The data, obtained for a free stream Mach number of 6 and a wing-root-chord Reynolds number of 18.5 million, reveal considerably larger regions of increased pressure and thermal loads than would be anticipated using non-separated flow analyses.

Kaufman, L. G., II↗

NASA NTRS1983

Effect of modifications of aerodynamic characteristics of a single-stage-to-orbit vehicle at Mach 5.9

Hypersonic stability, control, and performance characteristics were determined on a single-stage-to-orbit vehicle based on control-configured stability concepts. The configuration (0.006-scale model) had a large body with a small 50 deg swept wing. Two vertical-fin arrangements were investigated which consisted of a large center-line vertical tail and small wing-tip fins. The wing-tip fins had movable surfaces called controllers which could be deflected outward. Longitudinal and lateral directional characteristics were obtained over an angle-of-attack rage from 0 deg to 40 deg. The effects of tip-fin controller deflection on roll- and yaw-control characteristics at a sideslip angle of 0 deg were obtained. This investigation was conducted in the Langley 20 Inch Mach 6 Tunnel.

Bernot, P. T.↗

NASA NTRS1990

Supersonic aerodynamic characteristics of conformal carriage monoplanar circular missile configurations with low-profile quadriform tail fins

Wind tunnel tests were conducted on monoplanar circular missile configurations with low-profile quadriform tail fins to provide an aerodynamic data base to study and evaluate air-launched missile candidates for efficient conformal carriage on supersonic-cruise-type aircraft. The tests were conducted at Mach numbers from 1.70 to 2.86 for a constant Reynolds number per foot of 2,000,000. Selected test results are presented to show the effects of tail-fin dihedral angle, wing longitudinal and vertical location, and nose-body strakes on the static longitudinal and lateral-directional aerodynamic stability and control characteristics.

Blair, A. B., Jr.↗

NASA NTRS1990

Radiative configuration factors from cylinders to coaxial axisymmetric bodies

Exact solutions are obtained for the radiative configuration factor between differential elements of arbitrary orientation and cylinders. A general method is then proposed for calculating the view factor from a cylinder to a coaxial axisymmetric body using only a single numerical integration. The method is illustrated for axisymmetric bodies with function generators described by a power law equation. The method may be useful in calculating radiative heat transfer between cylindrical bodies and high-density exhaust gases and between annular radiative fins and their bases.

Saltiel, C.↗

NASA NTRS1954

A summary of information on support interference at transonic and supersonic speeds

An experimental investigation was performed to determine the effect on base and forebody pressures of using a sting modified with varying length splitter plates and fins instead of a conventional sting to support a cone-cylinder body of revolution. The investigation was conducted at a Mach number of 3.12 for a Reynolds number range of 2 x 10 to the 6th power to 14 x 10 to the 6th power and for an angle of attack range of 0 degrees to 9 degrees. For Reynolds numbers of 8 x 10 to the 6th power and 14 x 10 to the 6th power there was a negligible effect of the splitter plate modification on the base pressure, and at Reynolds number of 2 x 10 to the 6th power there was a small effect. Positioning the leading edge of the splitter plate at or ahead of the base made no appreciable change in the influence of the modifications on base pressure at a Reynolds number of 14 x 10 to the 6th power. With the fin-type modification there was a small increase in base pressure.

Love, Eugene S↗

NASA NTRS1994

Supersonic aerodynamic characteristics of a circular body Earth-to-Orbit vehicle

The circular body configuration is a generic single- or multi-stage reusable Earth-to-orbit transport. A thick clipped-delta wing is the major lifting surface. For directional control, three different vertical fin arrangements were investigated: a conventional aft-mounted center fin, wingtip fins, and a nose-mounted fin. The tests were conducted in the Langley Unitary Plan Wind Tunnel. The configuration is longitudinally stable about the estimated center of gravity of 0.72 body length up to a Mach number of about 3.0. Above Mach 3.0, the model is longitudinally unstable at low angles of attack but has a stable secondary trim point at angles of attack above 30 deg. The model has sufficient pitch control authority with elevator and body flap to produce stable trim over the test range. The model with the center fin is directionally stable at low angles of attack up to a Mach number of 3.90. The rudder-like surfaces on the tip fins and the all-movable nose fin are designed as active controls to produce artificial directional stability and are effective in producing yawing moment. The wing trailing-edge aileron surfaces are effective in producing rolling moment, but they also produce large adverse yawing moment.

Ware, George M.↗

NASA NTRS1976

Experimental aerodynamic characteristics for slender bodies with thin wings and tail at angles of attack from 0 deg to 58 deg and Mach numbers from 0.6 to 2.0

An experimental investigation was conducted by wind tunnel to measure the static aerodynamic characteristics for bodies of circular and elliptic cross section with various thin flat plate wings and a thin tail consisting of horizontal and vertical parts. The wings had aspect ratios of 4 and taper ratios of about 0, 0.25, and 0.5. Two additional wings, which had taper ratios near 0.25 and aspect ratios of about 3 and 5, were also tested in combination with the bodies and tail. All wings had about the same planform area. The exposed area of the horizontal portion of the tail was about 33 to 36 percent of the exposed area of the wings. The exposed area of the vertical tail fin was about 22 to 24 percent of the exposed area of the wings. The elliptic body, with an a/b = 2 cross section, had the same length and axial distribution of cross sectional area as the circular body. The circular body had a cylindrical aftersection of fineness ratio 7, and it was tested with the wings and tail in combination with tangent ogive noses that had fineness ratios of 2.5, 3.0, 3.5, and 5.0. In addition, an ogive nose with a rounded tip and an ogive nose with two different nose strake arrangements were used. Nineteen configuration combinations were tested at Mach numbers of 0.6, 0.9, 1.5, and 2.0 at angles of attack from 0 to 58 deg. The Reynolds numbers, based on body base diameter, were about 4.3 X 100,000.

Jorgensen, L. H.↗