Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - BODIES COMPRESSIBLE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1972

Quasi-one-dimensional compressible flow across face seals and narrow slots. 2: Computer program

A computer program is presented for compressible fluid flow with friction across face seals and through narrow slots. The computer program carries out a quasi-one-dimensional flow analysis which is valid for laminar and turbulent flows under both subsonic and choked flow conditions for parallel surfaces. The program is written in FORTRAN IV. The input and output variables are in either the International System of Units (SI) or the U.S. customary system.

Zuk, J.↗
NASA NTRS1974

Computer program for quasi-one-dimensional compressible flow with area change and friction - Application to gas film seals

A computer program is presented for compressible fluid flow with friction and area change. The program carries out a quasi-one-dimensional flow analysis which is valid for laminar and turbulent flows under both subsonic and choked flow conditions. The program was written to be applied to gas film seals. The area-change analysis should prove useful for choked flow conditions with small mean thickness, as well as for face seals where radial area change is significant. The program is written in FORTRAN 4.

Zuk, J.↗
NASA NTRS1950

Two-dimensional compressible flow in centrifugal compressors with straight blades

Six numerical examples are presented for steady, two-dimensional, compressible, nonviscous flow in centrifugal compressors with thin straight blades, the center lines of which generate the surface of a right circular cone when rotated about the axis of the compressor. A seventh example is presented for incompressible flow. The solutions were obtained in a region of the compressors, including the impeller tip, that was considered to be unaffected by the diffuser vanes or by the impeller-inlet configuration. Each solution applies to radial and mixed flow compressors with various cone angles but with the same angle between blades on the conic flow surface. The solution also apply to radial and mixed flow turbines with the rotation and the flow direction reversed. The effects of variations in the following parameters were investigated: (1) flow rate, (2) impeller-tip speed, (3) variation of passage height with radius, and (4) angle between blades on conic flow surface. The numerical results are presented in plots of the streamlines and constant Mach number lines. Correlation equations are developed whereby the flow conditions in any impeller with straight blades can be determined (in the region investigated by this analysis) for all operating conditions.

Stanitz, John D↗
NASA NTRS1989

A locally implicit finite element analysis algorithm for 3-D compressible flows

The paper outlines the research results on the development of a finite-element analysis procedure for three-dimensional compressible viscous flows. Some new algorithmic features of the computational model, such as a locally implicit solution scheme which avoids the necessity of computation and assembly of global matrices. The new algorithm makes it applicable to large-scale three-dimensional flow problems of practical interest, for example, the analysis of flows in Space Shuttle Main Engine (SSME).

Reddy, K. C.↗
NASA NTRS1993

Line relaxation methods for the solution of 2D and 3D compressible flows

An implicit finite element based algorithm for the compressible Navier-Stokes equations is outlined, and the solution of the resulting equation by a line relaxation on general meshes of triangles or tetrahedra is described. The problem of generating and adapting unstructured meshes for viscous flows is reexamined, and an approach for both 2D and 3D simulations is proposed. An efficient approach appears to be the use of an implicit/explicit procedure, with the implicit treatment being restricted to those regions of the mesh where viscous effects are known to be dominant. Numerical examples demonstrating the computational performance of the proposed techniques are given.

Hassan, O.↗
NASA NTRS1986

Simple numerical method for predicting steady compressible flows

A numerical method for solving the isenthalpic form of the governing equations for compressible viscous and inviscid flows was developed. The method was based on the concept of flux vector splitting in its implicit form. The method was tested on several demanding inviscid and viscous configurations. Two different forms of the implicit operator were investigated. The time marching to steady state was accelerated by the implementation of the multigrid procedure. Its various forms very effectively increased the rate of convergence of the present scheme. High quality steady state results were obtained in most of the test cases; these required only short computational times due to the relative efficiency of the basic method.

Vonlavante, Ernst↗
NASA NTRS1938

Two-dimensional subsonic compressible flow past elliptic cylinders

The method of Poggi is used to calculate, for perfect fluids, the effect of compressibility upon the flow on the surface of an elliptic cylinder at zero angle of attack and with no circulation. The result is expressed in a closed form and represents a rigorous determination of the velocity of the fluid at the surface of the obstacle insofar as the second approximation is concerned. Comparison is made with Hooker's treatment of the same problem according to the method of Janzen and Rayleight and it is found that, for thick elliptic cylinders, the two methods agree very well. The labor of computation is considerably reduced by the present solution.

Kaplan, Carl↗
NASA NTRS2013

Design of a Variational Multiscale Method for Turbulent Compressible Flows

A spectral-element framework is presented for the simulation of subsonic compressible high-Reynolds-number flows. The focus of the work is maximizing the efficiency of the computational schemes to enable unsteady simulations with a large number of spatial and temporal degrees of freedom. A collocation scheme is combined with optimized computational kernels to provide a residual evaluation with computational cost independent of order of accuracy up to 16th order. The optimized residual routines are used to develop a low-memory implicit scheme based on a matrix-free Newton-Krylov method. A preconditioner based on the finite-difference diagonalized ADI scheme is developed which maintains the low memory of the matrix-free implicit solver, while providing improved convergence properties. Emphasis on low memory usage throughout the solver development is leveraged to implement a coupled space-time DG solver which may offer further efficiency gains through adaptivity in both space and time.

Design↗
NASA NTRS1981

Extension to an analysis of turbulent swirling compressible flow for application to axisymmetric small gas turbine ducts

An existing computer program, the Axisymmetric Diffuser Duct Code (ADD code), which calculates compressible turbulent swirling flow through axisymmetric ducts was modified to permit calculation of flows through small gas turbine ducts with struts, guide vanes and large degrees of turning. The improvements include a coordinate generator, an end-wall loss model, and a generalized geometry capability to describe struts and guide vanes in ducts which turn more than 90 degrees. An improved output format was developed to provide the solution on any arbitrary plane in the duct and an extensive literature survey of calculation procedures used in gas turbine technology was completed which suggests improvements in the computer code. Calculations are presented for the flow through the AGT101 small gas turbine inlet duct and turbine exhaust diffuser which demonstrate the ADD code modifications implemented in the investigation. The computed results compare favorably with experimental results.

Anderson, O. L.↗
NASA NTRS1985

Slow plastic strain rate compressive flow in binary CoAl intermetallics

Constant-velocity elevated temperature compression tests have been conducted on a series of binary CoAl intermetallics produced by hot extrusion of blended prealloyed powders. The as-extruded materials were polycrystalline, and they retained their nominal 10-micron grain size after being tested between 1100 and 1400 K at strain rates ranging from 2 x 10 to the -4th to 2 x 10 to the -7th per sec. Significant plastic flow was obtained in all cases; while cracking was observed, much of this could be due to failure at matrix-oxide interfaces along extrusion stringers rather than to solely intergranular fracture. A maximum in flow strength occurs at an aluminum-to-cobalt ratio of 0.975, and the stress exponent appears to be constant for aluminum-to-cobalt ratios of 0.85 or more. It is likely that very aluminum-deficient materials deform by a different mechanism than do other compositions.

Whittenberger, J. D.↗
NASA NTRS1987

Simple numerical method for predicting steady compressible flows

The present numerical method for the solution of the isenthalpic form of the governing equations for compressible viscous and inviscid flows has its basis in the concept of flux vector splitting in its implicit form, and has been tested in the cases of several difficult viscous and inviscid configurations. An acceleration of time-marching to steady state is accomplished by implementing a multigrid procedure which effectively increases the convergence rate. The steady state results obtained are largely of good quality, and required only short computational times.

Von Lavante, E.↗
NASA NTRS1988

Calculation of the recirculating compressible flow downstream a sudden axisymmetric expansion

Significant progress has been made during the last five years to adapt conventional Navier-Stokes solver for handling nonconservative equations. A primary type of application is to use transport equation turbulence models, but the extension is also possible for describing the transport of nonpassive scalars, such as in reactive media. Among others, combustion and gas dissociation phenomena are topics needing a considerable research effort. An implicit two step scheme based on the well-known MacCormack scheme has been modified to treat compressible turbulent flows on complex geometries. Implicit treatment of nonconservative equations (in the present case a two-equation turbulence model) opens the way to the coupled solution of thermochemical transport equations.

Vandromme, D.↗
NASA NTRSDate not supplied

Enabling Metric-Based Mesh Adaptation for Advanced Compressible Flow Simulations Using US3D

This work presents a metric-based mesh adaptation capability added to the flow solver US3D that is used to improve the accuracy of atmospheric entry simulations. Flow past an entry vehicle in free-flight is usually unsteady and characterized by anisotropic flow features like a strong bow shock and small-scale isotropic flow features like turbulent eddies in the wake. The results presented in this paper demonstrate that we are currently able to iteratively apply metric-based mesh adaptation to improve the solution accuracy by simultaneously targeting isotropic and anisotropic flow features. A simplified workflow of running CFD simulations for entry vehicles is presented where we start off with a coarse initial mesh to compute a first approximation of the flow. This coarse mesh is then iteratively refined using the newly developed metric to improve the resolution of the CFD computation. Furthermore, we demonstrate that we are able to adapt large mesh sizes in a timely fashion which allows us to start thinking about applying this adaptive framework to unsteady atmospheric entry CFD simulations.

Mesh adaptation↗
NASA NTRS1981

On the effect of boundary layer growth on the stability of compressible flows

The method of multiple scales is used to describe a formally correct method based on the nonparallel linear stability theory, that examines the two and three dimensional stability of compressible boundary layer flows. The method is applied to the supersonic flat plate layer at Mach number 4.5. The theoretical growth rates are in good agreement with experimental results. The method is also applied to the infinite-span swept wing transonic boundary layer with suction to evaluate the effect of the nonparallel flow on the development of crossflow disturbances.

El-Hady, N. M.↗
NASA NTRS1975

Experimental investigation of a Mach 6 fixed-geometry inlet featuring a swept external-internal compression flow field

An investigation of a fixed-geometry, swept external-internal compression inlet was conducted at a Mach number of 6.0 and a test-section Reynolds number of 1.55 x 10 to the 7th power per meter. The test conditions was constant for all runs with stagnation pressure and temperature at 20 atmospheres and 500 K, respectively. Tests were made at angles of attack of -5 deg, 0 deg, 3 deg, and 5 deg. Measurements consisted of pitot- and static-pressure surveys in inlet throat, wall static pressures, and surface temperatures. Boundary-layer bleed was provided on the centerbody and on the cowl internal surface. The inlet performance was consistently high over the range of the angle of attack tested, with an overall average total pressure recovery of 78 percent and corresponding adiabatic kinetic-energy efficiency of 99 percent. The inlet throat flow distribution was uniform and the Mach number and pressure level were of the correct magnitude for efficient combustor design. The utilization of a swept compression field to meet the starting requirements of a fixed-geometry inlet produced neither flow instability nor a tendency to unstart.

Torrence, M. G.↗