Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW - PLATES, FLAT - SUPERSONIC”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Hypersonic, stratified gas flows past an obstacle - Direct simulation Monte Carlo calculations

Monte Carlo particle dynamics are presently used to study the interaction of a stratified gas that impinges hypersonically on a solid body, whose size is comparable to the gas scale height. Attention is given to the results of these computations for two representative cases, where the obstacle adopted is a short, uniform cylindrical pipe whose upstream end is fully open, facing directly into the flow, while the downstream end is covered by a flat circular endplate containing an 'orifice' at its center. The cases are those of a completely closed and a fully open orifice; together, these bound the full range of obstructed hypersonic, stratified gas flows of interest.

Roberts, William W., Jr.↗
NASA NTRS1995

A test of a vortex method for the computation of flap side edge noise

Upon approach to landing, a major source location of airframe noise occurs at the side edges of the part span, trailing edge flaps. In the vicinity of these flaps, a complex arrangement of spanwise flow with primary and secondary tip vortices may form. Each of these vortices is observed to become fully three-dimensional. In the present study, a numerical model is developed to investigate the noise radiated from the side edge of a flap. The inherent three-dimensionality of this flow forces us to carefully consider a numerical scheme which will be both accurate in its prediction of the flow acoustics and also computationally efficient. Vortex methods have offered a fast and efficient means of simulating many two and three-dimensional, vortex dominated flows. In vortex methods, the time development of the flow is tracked by following exclusively the vorticity containing regions. Through the Biot-Savart law, knowledge of the vorticity field enables one to obtain flow quantities at any desired location during the flow evolution. In the present study, a numerical procedure has been developed which incorporates the Lagrangian approach of vortex methods into a calculation for the noise radiated by a flow-surface interaction. In particular, the noise generated by a vortex in the presence of a flat half plane is considered. This problem serves as a basic model of flap edge flow. It also permits the direct comparison between our computed results and previous acoustic analyses performed for this problem. In our numerical simulations, the mean flow is represented by the complex potential W(z) = Aiz(exp l/2), which is obtained through conformal mapping techniques. The magnitude of the mean flow is controlled by the parameter A. This mean flow has been used in the acoustic analysis by Hardin and is considered a reasonable model of the flow field in the vicinity of the edge and away from the leading and trailing edges of the flap. To represent the primary vortex which occurs near the flap, a point vortex is introduced just below the flat half plane. Using a technique from panel methods, boundary conditions on the flap surface are satisfied by the introduction of a row of stationary point vortices along the extent of the flap. At each time step in the calculation, the strength of these vortices is chosen to eliminate the normal velocity at intermediary collocation points. The time development of the overall flow field is then tracked using standard techniques from vortex methods. Vortex trajectories obtained through this computation are in good agreement with those predicted by the analytical solution given by Hardin, thus verifying the viability of this procedure for more complex flow arrangements. For the flow acoustics, the Ffowcs Williams-Hawkings equation is numerically integrated. This equation supplies the far field acoustic pressure based upon pressures occurring along the flap surface. With our vortex method solution, surface pressures may be obtained with exceptional resolution. The Ffowcs Williams-Hawkings equation is integrated using a spatially fourth order accurate Simpson's rule. Rational function interpolation is used to obtain the surface pressures at the appropriate retarded times. Comparisons between our numerical results for the acoustic pressure and those predicted by the Hardin analysis have been made. Preliminary results indicate the need for an improved integration technique. In the future, the numerical procedure developed in this study will be applied to the case of a rectangular flap of finite thickness and ultimately modified for application to the fully three-dimensional problem.

Martin, James E.↗
NASA NTRS1954

Investigation of the Jet Effects on a Flat Surface Downstream of the Exit of a Simulated Turbojet Nacelle at a Free-Stream Mach Number of 2.02

An investigation at a free-stream Mach number of 2.02 was made to determine the effects of a propulsive jet on a wing surface located in the vicinity of a choked convergent nozzle. Static-pressure surveys were made on a flat surface that was located in the vicinity of the propulsive jet. The nozzle was operated over a range of exit pressure ratios at different fixed vertical distances from the flat surface. Within the scope of this investigation, it was found that shock waves, formed in the external flow because of the presence of the propulsive jet, impinged on the flat surface and greatly altered the pressure distribution. An integration of this pressure distribution, with the location of the propulsive jet exit varied from 1.450 propulsive-jet exit diameters to 3.392 propulsive-jet exit diameters below the wing, resulted in an incremental lift for all jet locations that was equal to the gross thrust at an exit pressure ratio of 2.86. This incremental lift increased with increase in exit pressure ratio, but not so rapidly as the thrust increased, and was approximately constant at any given exit pressure ratio.

Bressette, Walter E.↗
NASA NTRS2001

Real-time three-dimensional color Doppler echocardiography for characterizing the spatial velocity distribution and quantifying the peak flow rate in the left ventricular outflow tract

Quantification of flow with pulsed-wave Doppler assumes a "flat" velocity profile in the left ventricular outflow tract (LVOT), which observation refutes. Recent development of real-time, three-dimensional (3-D) color Doppler allows one to obtain an entire cross-sectional velocity distribution of the LVOT, which is not possible using conventional 2-D echo. In an animal experiment, the cross-sectional color Doppler images of the LVOT at peak systole were derived and digitally transferred to a computer to visualize and quantify spatial velocity distributions and peak flow rates. Markedly skewed profiles, with higher velocities toward the septum, were consistently observed. Reference peak flow rates by electromagnetic flow meter correlated well with 3-D peak flow rates (r = 0.94), but with an anticipated underestimation. Real-time 3-D color Doppler echocardiography was capable of determining cross-sectional velocity distributions and peak flow rates, demonstrating the utility of this new method for better understanding and quantifying blood flow phenomena.

NASA Discipline Cardiopulmonary↗
NASA NTRS2014

Acoustic Measurements from Wind Tunnel Test of AMELIA - Advanced Model for Extreme Lift and Improved Aeroacoustics

A wind tunnel test has been conducted to measure the aerodynamic and acoustic performance of an active circulation-control aircraft with leading- and trailing- edge slot blowing. The 11 Advanced Model for Extreme Lift and Improved Aeroacoustics (AMELIA) model was tested in the Arnold Engineering Development Center (AEDC) National Full Scale Aerodynamics Complex (NFAC) 40- by 80-Ft wind tunnel. Forward velocities ranged from 0 to Mach 0.15 and total slot mass-flow was varied from 0 to 2.8 lbmsec. Angle-of-attack and sideslip ranges were -5 to 25 and -10 to 10, respectively.This reports summarizes acoustic measurements from the wind tunnel test and the corrections applied to the released acoustic data. The analysis focuses on measurements for the clean wing configuration (turbine propulsion simulators removed) with trailing-and leading-edge slot blowing and with trailing-edge blowing, for systematic variations in slot mass flow from nearly zero to the system maximum. The acoustic measurements from a fixed phased microphone array and seven fixed microphones were corrected for sensor directional response and atmospheric attenuation. Graphs of 13-octave spectra, narrowband spectra, and directional variations in OASPL are presented for each active lift configuration. This report is intended to document the corresponding set of corrected data that is now available for development and verification of new predictive models of the active lift source.For large slot mass flow conditions 13-octave spectral shapes were level and flat, typical of a pink noise source. Little source directivity was present in the OASPL levels for the 0 flap conditions and show only a slight downstream increase with the 60 flap configuration. For moderate to high slot mass flow conditions trailing-edge only blowing spectra were similar to leading- and trailing edge blowing cases. However for the lower mass flows variations of as much as 5 dB were observed.

CCW↗
NASA NTRS1995

The effect of plasma heating on sublimation-driven flow in Io's atmosphere

The atmospheric flow on Io is numerically computed in a flat 2-D axisymmetric geometry for a sublimation atmosphere on the trailing hemisphere subjected to plasma bombardment, UV heating, and IR cooling. Calculations are performed for subsolar vapor pressures of approximately 6.5 x 10(exp -3) Pa (approximately 3 x 10(exp 18) SO2/sq cm) and 6.8 x 10(exp -4) Pa (approximately 4 x 10(exp 17) SO2/sq cm); the latter approximates the vapor pressure of F. P. Fanale et al. (1982). The amount of plasma energy deposited in the atmosphere is 20% of the plasma flow energy due to corotation (J. A. Linker et al., 1988). It is found that plasma heating significantly inflates the upper atmosphere, increasing both the exobase altitude and the amount of surface covered by more than an exospheric column of gas. This in turn controls the supply of the Io plasma torus (M. A. McGrath and R. E. Johnson, 1987). The horizontal flow of mass and energy is also important in determining the exobase altitude; and it is shown that IR cooling can be important, although our use of the equilibrium, cool-to-space approximation for a pure SO2 gas (E. Lellouch et al., 1992) may overestimate this effect. The calculated exobase altitudes are somewhat lower than those suggested by McGrath and Johnson (1987) for supplying the torus, indicating the details of the plasma energy deposition and sputter ejection rate near the exobase, as well as the IR emission from this region need to be examined. In addition, the molecules sublimed (or sputtered) from the surface are transported to the exobase in times short compared to the molecular photodissociation time. Therefore, the exobase is dominated by molecular species and the exobase is supplied by a small region of the surface.

Wong, Mau C.↗
NASA NTRS1978

A study of the structural-acoustic response and interior noise levels of fuselage structures

Models of both flat and curved fuselage panels were tested for their sound transmission characteristics. The effect of external air flow on transmission loss was simulated in a subsonic wind-tunnel. By numerically evaluating the known equations for field-incidence transmission loss of single-walled panels in a computer program, a comparison of the theory with the test results was made. As a further extension to aircraft fuselage simulation, equations for the field-incidence transmission loss of a double-walled panel were derived. Flow is shown to provide a small increase in transmission loss for a flat panel. Curvature is shown to increase transmission loss for low frequencies, while also providing a sharp decrease in transmission loss at the ring frequency of the cylindrical panel. The field-incidence transmission loss of a double-walled panel was found to be approximately twice that for a single-walled panel, with the addition of dips in the transmission loss at the air gap resonances and at the critical frequency of the internal panel.

Koval, L. R.↗
NASA NTRS1977

An experimental investigation of a three dimensional wall jet

One and two point statistical properties are measured in the flow fields of a coflowing turbulent jet. Two different confining surfaces (one flat, one with large curvature) are placed adjacent to the lip of the circular nozzle; and the resultant effects on the flow field are determined. The one point quantities measured include mean velocities, turbulent intensities, velocity and concentration autocorrelations and power spectral densities, and intermittencies. From the autocorrelation curves, the Taylor microscale and the integral length scale are calculated. Two point quantities measured include velocity and concentration space-time correlations and pressure velocity correlations. From the velocity space-time correlations, iso-correlation contours are constructed along with the lines of maximum maximorum. These lines allow a picture of the flow pattern to be determined. The pressures monitored in the pressure velocity correlations are measured both in the flow field and at the surface of the confining wall(s).

Catalano, G. D.↗
DOE OSTI2023

TEAMER: Experimental performance characterization of a shrouded axial-flow turbine

Sitkana has developed a shrouded hydrokinetic turbine with a modular, low-cost design that can be scaled to meet the needs of remote communities. With technical support from the University of Washington, Sitkana sought to experimentally characterize the mechanical power and structural loads of various 1:3.3 scale rotor geometries. In all, 11 different rotor geometries were characterized with variations in height-to-diameter ratio, blade number, and blade type (foiled versus flat). All tests were conducted in Reynolds-independent flow conditions in the Alice C. Tyler Flume at the University of Washington. Results allow Sitkana to (1) refine the optimal rotor geometry, (2) validate numerical models, and (3) predict power output for a full-scale system. This project is part of the TEAMER RFTS 8 (request for technical support) program.

16 TIDAL AND WAVE POWER↗
NASA NTRS1975

Flow-establishment times for blunt bodies in an expansion tube

Flow establishment results are presented as obtained from shock standoff distance, pressure, and heat transfer measurements in the Langley expansion tube. The models tested were flat-faced cylinders with varying radius and a sphere with a constant radius, and they were positioned at the acceleration section exit and tested in the open jet at zero angle of attack. The experimental results were obtained as spinoff from various studies using helium, air, and CO2 test gases at freestream velocities in the range 5-7 km/sec. Time histories of shock detachment distance illustrate that the shock formation about the smaller-radii flat-faced cylinders and the sphere is symmetrical, whereas a complex, asymmetric formation is observed for the larger-radii cylinders. Flow is shown to establish more readily about the sphere than a flat-faced cylinder of the same diameter. A quasi-steady flow exists about relatively large blunt models during two-thirds of the approximate 250-microsec expansion tube test period.

Miller, C. G.↗
NASA NTRS1979

The growth of aspherical structure in the universe - Is the Local Supercluster an unusual system

The growth and subsequent collapse of homogeneous ellipsoidal perturbations in a uniform expanding background is considered as a simple model for the formation of large-scale aspherical structures in the observed universe. Numerical calculations of the evolution of such perturbations turn out to be well described by an approximate analytic solution of the equations of motion, and simple relationships are found between the initial shape of a perturbation and its shape and kinematic properties at the time of collapse. Perturbations do not change their shape significantly until they reach a density contrast of order unity. As a result, structures with the kinematic properties of the Local Supercluster should form much more commonly in a low-density universe than in a flat universe. The homogeneity of the local Hubble flow, the motion of the Milky Way with respect to the microwave background, and the flattening of the Local Supercluster can be successfully accounted for by these models, provided that the initial perturbation is sufficiently flattened. Viable models are obtained only if the ratio of the lengths of the two smaller axes of the initial perturbation is at least 3:1 in an Einstein-de Sitter universe or at least 1.8:1 in a universe for which the density parameter (Omega) is of order 0.1, when the protocluster pancakes.

White, S. D. M.↗
NASA NTRS1989

High-Capacity Heat-Pipe Evaporator

Heat pipe with cylindrical heat-input surface has higher contact thermal conductance than one with usual flat surface. Cylindrical heat absorber promotes nearly uniform flow of heat into pipe at all places around periphery of pipe, helps eliminate hotspots on heat source. Lugs in aluminum pipe carry heat from outer surface to liquid oozing from capillaries of wick. Liquid absorbs heat, evaporates, and passes out of evaporator through interlug passages.

Oren, J. A.↗
NASA NTRS1991

Computational aspects of chemically reacting flows

An implicit, time-dependent approach is taken to solve the inviscid conservative equations in a vertex-based finite-volume formulation. The convective fluxes are estimated by a modified Riemann solver, and higher-order accuracy is obtained by means of the MUSCL. Implicit techniques are adopted to deal with the equation stiffness as a result of the clustered grid and chemical source term. The real-gas Roe matrix and the ADI and LU schemes have been tested on the sample problems: hypersonic flow over blunt configurations, such as the forebody of a double ellipse, and the near wake of a conic aerobrake. Temperature distribution and standoff distance are validated against the shock-fitting, central-differencing results. Equilibrium temperature may be recovered by artificially increasing the chemical rates at the wall. The present method satisfactorily resolves the flow structure, including the strong expansion behind the flat base. The relative merits and performance of the real-gas TVD and implicit schemes are discussed briefly.

Li, C. P.↗
NASA NTRS1991

Static and Dynamic Pressure Distributions in a Short Labyrinth Seal

As part of a study into turbine blade tip destabilizing forces, a seals test rig was built in which spin rate, circular whirl rate, direction and amplitude of inlet swirl angle, and eccentricity can all be controlled over wide ranges, and measurements can be made at gap Reynolds numbers up to about 2 x 10(exp 4). This facility is described and preliminary data is presented for a one cavity labyrinth seal with a flat, stator mounted land. The impact of different flow coefficients for the first and second knives on the rotordynamic coefficients was found. While this effect is dominant for the direct forces, it should also be incorporated into calculations of cross forces where it has an impact under many conditions.

Millsaps, K. T.↗
NASA NTRS1984

Direct numerical simulation of curved turbulent channel flow

Low Reynolds number, mildly curved, turbulent channel flow has been simulated numerically without subgrid scale models. A new spectral numerical method developed for this problem was used, and the computations were performed with 2 million degrees of freedom. A variety of statistical and structural information has been extracted from the computed flow fields. These include mean velocity, turbulence stresses, velocity skewness, and flatness factors, space time correlations and spectra, all the terms in the Reynolds stress balance equations, and contour and vector plots of instantaneous velocity fields. The effects of curvature on this flow were determined by comparing the concave and convex sides of the channel. The observed effects are consistent with experimental observations for mild curvature. The most significant difference in the turbulence statistics between the concave and convex sides was in the Reynolds shear stress. This was accompanied by significant differences in the terms of the Reynolds shear stress balance equations. In addition, it was found that stationary Taylor-Gortler vortices were present and that they had a significant effect on the flow by contributing to the mean Reynolds shear stress, and by affecting the underlying turbulence.

Moser, R. D.↗
NASA NTRS1990

Performance of the Bowen ratio systems on a 22 deg slope

The Bowen ratio energy balance technique was used to assess the energy fluxes on inclined surfaces during the First ISLSCP Field Experiment (FIFE). Since air flow over sloping surface may differ from that over flat terrain, it is important to examine whether Bowen ratio measurements taken on sloping surfaces are valid. In this study, the suitability of using the Bowen ratio technique on sloping surfaces was tested by examining the assumptions that the technique requires for valid measurements. This was accomplished by studying the variation of Bowen ratio measurements along a selected slope at the FIFE site. In September 1988, four Bowen ratio systems were set up in a line along the 22 degree north-facing slope with northerly air flow (wind went up the slope). In July of 1989, six Bowen ratio systems were similarly installed with southerly air flow (the wind went down slope). Results indicated that, at distances between 10 to 40 meters from the top of the slope, no temperature or vapor pressure gradient parallel to the slope was detected. Uniform Bowen ratio values were obtained on the slope, and thus the sensible or latent heat flux should be similar along the slope. This indicates that the assumptions for valid flux measurements are reasonably met at the slope. The Bowen ratio technique should give the best estimates of the energy fluxes on slopes similar to that in this study.

Nie, D.↗
DOE OSTI2021

Impact of Lateral Flow on Surface Water and Energy Budgets over the Southern Great Plains – A Modeling Study

As we see the horizontal grid spacing decrease, treatment of hydrologic processes in land surface models, such as the lateral flow of surface and subsurface flow, need to be explicitly represented. Unlike previous studies that mainly focused on the mountainous regions, in this study the offline WRF-Hydro model is employed to study the impact of lateral flow on soil moisture and energy fluxes over the relatively flat southern Great Plains (SGP). The vast amount of measurements over the SGP provide an unique opportunity to assess the model behavior. In addition, newly developed land surface properties and input forcing are ingested into the model, in an attempt to reduce uncertainties associated with the initial and boundary forcing and help to identify model deficiencies. Our results show that the more realistic inputs (parameters, soil types, forcing) lead to larger underestimation of latent heat flux and dry bias, indicating the existence of model structural uncertainty (embedded errors) in WRF-Hydro that need to be characterized to inform future model development efforts. Including lateral flow processes partly mitigates the model deficiencies in representing hydrologic processes and alleviates the dry bias. In particular, both surface and subsurface lateral flow increase soil moisture mainly over the lower elevations, except that subsurface flow also affects soil moisture over steeper terrains. Additional simulations are performed to assess the effect of routing resolution on model results. When LSM resolution is high, noticeable differences in soil moisture are produced between different routing resolutions especially over steep terrain. Whereas when LSM resolution is coarse, differences between routing resolutions become negligible, especially over flat terrain.

54 ENVIRONMENTAL SCIENCES↗
NASA NTRS1982

Escalator design features evaluation

Escalators are available with design features such as dual speed (90 and 120 fpm), mat operation and flat steps. These design features were evaluated based on the impact of each on capital and operating costs, traffic flow, and safety. A human factors engineering model was developed to analyze the need for flat steps at various speeds. Mat operation of escalators was found to be cost effective in terms of energy savings. Dual speed operation of escalators with the higher speed used during peak hours allows for efficient operation. A minimum number of flat steps required as a function of escalator speed was developed to ensure safety for the elderly.

Zimmerman, W. F.↗