Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLOW DISTRIBUTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1989

CFD simulation of square cross-section, contoured nozzle flows - Comparison with data

Computational analyses have been made of the flow in NASA Langley's Arc-Heated Scramjet Test Facility's Mach 4.7 and Mach 6 square cross-section contoured nozzles, for comparison with experimental results. The analyses, which were performed using a three-dimensional RANS computer code assuming a single species gas with constant specific heats, were intended to provide insight into the nature of the flow development in this type of nozzle. The computational results showed the exit flow distribution to be affected by counter-rotating vortices along the centerline of each nozzle sidewall. Calculated flow properties show general, but not complete, agreement with experimental measurements in both nozzles.

Ostrander, Mark J.↗
NASA NTRS1974

Mean and fluctuating flow measurements in axisymmetric supersonic boundary layer flow subjected to distributed adverse pressure gradients

Measurements have been made of the mean flow properties and turbulent fluctuations in adiabatic turbulent boundary layer flows subjected to distributed adverse pressure gradients. In the freestream region upstream of the adverse pressure gradient the Mach number was 3.86, the unit Reynolds number 5.3 million per foot. The boundary layer developed on the wall of an axisymmetric nozzle and straight test section. In order to avoid the effects of streamwise surface curvature the adverse pressure gradients at the test section wall were induced by contoured centerbodies mounted on the wind tunnel centerline. The flow under study simulated that which might be found in an axially symmetric engine inlet of a supersonic aircraft.

Gootzait, E.↗
NASA NTRS1981

A further study of the annual cycle of the zonal mean circulation in the middle atmosphere

The influence on the stratospheric mean circulation of planetary wavenumber 2 disturbances excited by steady forcing at the 100 mb level is investigated using a global semi-spectral primitive equation model. There exists a critical forcing amplitude below which the waves have little effect on the mean flow, while above which the waves produce subseasonal time scale vacillations in the winter hemisphere, including both major and minor warmings. Wave transience induced by the evolving mean flow distribution is responsible for generating the vacillations, while thermal damping serves to reduce the wave-driven changes in the mean flow.

Holton, J. R.↗
NASA NTRS1992

Simultaneous mapping of the unsteady flow fields by Particle Displacement Velocimetry (PDV)

Current experimental and computational techniques must be improved in order to advance the prediction capability of the longitudinal vortical flows shed by underwater vehicles. The generation, development, and breakdown mechanisms of the shed vortices at high Reynolds numbers are not fully understood. The ability to measure hull separated vortices associated with vehicle maneuvering does not exist at present. The existing point-by-point measurement techniques can only capture approximately the large 'mean' eddies but fail to meet the dynamics of small vortices during the initial stage of generation. A new technique, which offers a previously unavailable capability to measure the unsteady cross-flow distribution in the plane of the laser light sheet, is called Particle Displacement Velocimetry (PDV). PDV consists of illuminating a thin section of the flowfield with a pulsed laser. The water is seeded with microscopic, neutrally buoyant particles containing imbedded fluorescing dye which responds with intense spontaneous fluorescence with the illuminated section. The seeded particles in the vortical flow structure shed by the underwater vehicle are illuminated by the pulse laser and the corresponding particle traces are recorded in a single photographic frame. Two distinct approaches were utilized for determining the velocity distribution from the particle traces. The first method is based on matching the traces of the same particle and measuring the distance between them. The direction of the flow can be identified by keeping one of the pulses longer than the other. The second method is based on selecting a small window within the image and finding the mean shift of all the particles within that region. The computation of the auto-correlation of the intensity distribution within the selected sample window is used to determine the mean displacement of particles. The direction of the flow is identified by varying the intensity of the laser light between pulses. Considerable computational resources are required to compute the auto-correction of the intensity distribution. Parallel processing will be employed to speed up the data reduction. A few examples of measured unsteady vortical flow structures shed by the underwater vehicles will be presented.

Huang, Thomas T.↗
NASA NTRS1989

Comparison of measured induced velocities with results from a closed-form finite state wake model in forward flight

An unsteady, three-dimensional induced-flow model is applied to compute the induced-flow distribution of a rotor in forward flight, and numerical results are compared against LDV measurements for both time-averaged and unsteady induced flow at the disk. The former flow shows good agreement with measured data, except just behind the pylon at the lowest advanced ratio and near the blade tips for rectangular blades at high advance ratios. The method performs as well or better than other codes that have been applied to these data, takes less computing time, and is better suited to aeroelastic analysis. Results with only four harmonics and 15 state variables converge to all fundamental characteristics of the time-averaged flow.

Peters, David A.↗
NASA NTRS1991

Investigations of detail design issues for the high speed acoustic wind tunnel using a 60th scale model tunnel. Part 1: Tests with open circuits

This report summarizes the tests on the 1:60 scale model of the High Speed Acoustic Wind Tunnel (HSAWT) performed during the period of November 1989 to December 1990. Throughout the testing the tunnel was operated in the 'open circuit mode', that is when the airflow was induced by a powerful exhaust fan located outside the tunnel circuit. The tests were first performed with the closed test section and were subsequently repeated with the open test section. While operating with the open test section, a novel device, called the 'nozzle-diffuser,' was also tested in order to establish its usefulness of increasing pressure recovery in the first diffuser. The tests established the viability of the tunnel design. The flow distribution in each tunnel component was found acceptable and pressure recovery in the diffusers were found satisfactory. The diffusers appeared to operate without flow separation. All tests were performed at NASA LaRC.

Barna, P. Stephen↗
NASA NTRS1952

Investigations of Air-Cooled Turbine Rotors for Turbojet Engines. 1: Experimental Disk Temperature Distribution in Modified J33 Split-Disk Rotor at Speeds up to 6000 RPM

An experimental investigation is being conducted at the Lewis laboratory to establish general principles for the design of noncritical turbine rotor configurations. This investigation includes evaluation of cooling effectiveness, structural stability, cooling-air flow distribution characteristics, and methods of supplying cooling air to the turbine rotor blades. Prior to design of a noncritical rotor, a standard turbine rotor of a commerical turbojet engine was split in the plane of rotation and machined to provide a passage for distributing cooling air to the base of each blade. The rotor was fitted with nontwisted, hollow, aircooled blades containing nine tubes in the coolant passage. In the investigation reported herein, the modified turbine rotor operated successfully up to speeds of 6000 rpm with ratios of cooling-air to combustion-gas flow as low as 0.02. The disk temperatures observed at these conditions were below 450 0 F when cooling air at 100 F was used from the laboratory air system. The calculated disk temperatures based on the correlation method presented for rated engine conditions were well below 1000 F at a cooling-air flow ratio of 0.02, which is considered adequate for a noncritical rotor. An appreciable difference in temperature level existed between the forward and rear disks. This temperature difference probably introduced undesirable disk stress distributions as a result of the relative elongations of the two disks. This investigation was terminated at 6000 rpm so that slight changes in the engine configuration could be made to relieve this condition.

Schramm, Wilson B.↗
NASA NTRS1982

Aerothermal modeling program

Some significant features of the approach adopted for the combustor aerothermal modeling program are described. The individual computerized models utilized in the aero design approach are characterized. The preliminary design module provides the overall envelope definition of the burner. The diffuser module provides the detailed contours of the diffuser and combustor cowl region, as well as the pressure loss characteristics into each of the individual flow passages into the dome and around the combustor. The flow distribution module provides the air entry quantities through each of the aperatures and the overall pressure drop. The heat transfer module provides detailed metal temperature distribution throughout the metal structure as input to stress and life analysis that are not part of the aerothermo design effort. Finally, the internal flow module, INTFLOW, is described and the approach for model evaluation using laboratory data is discussed.

Kenworthy, M.↗
NASA NTRS1983

Analysis of coolant entrance boundary shape of porous region to control cooling along exit boundary

A cooled porous region has a plane surface exposed to a specified spatially varying heat flux. The coolant leaves the region through this surface, and it is desired to control the flow distribution to maintain a specified uniform surface temperature. This is accomplished by having the coolant entrance surface shaped to provide in the region the necessary variation of path length and, hence, flow resistance. The surface shape at the coolant entrance is found by solving a Cauchy boundary value problem. An exact solution is obtained that will deal with a wide variety of heating distributions for both two- and three-dimensional shapes.

Siegel, R.↗
NASA NTRS1952

Solutions of laminar-boundary-equations which result in specific-weight-flow profiles locally exceeding free-stream values

Revised solutions of the laminar-boundary-layer equations for cases which involved cooling at the wall combined with large pressure gradients in the main stream produced specific-weight-flow profiles which locally exceeded free-stream values. Heat-transfer and friction coefficients, boundary-layer thicknesses, and velocity, temperature, and specific-weight-flow distributions resulting from the revised solutions are presented for Euler numbers of 0.5 and 1, stream-to-wall temperature ratios of 2 and 4, and cooling-air flow rates through porous walls designated by flow parameters of 0, -0.5, and -1.

HEAT TRANSFER, AERODYNAMIC↗
NASA NTRS1954

Smoke Study of Nozzle Secondary Flows in a Low-speed Turbine

Still and motion pictures were made of boundary-layer and wake secondary-flow phenomena visualized by smoke. Two annular cascades of turbine nozzles were used, both designed for constant discharge angle but differing in blade shape and suction-surface velocity distribution. Flows were similar to those obtained with pressure and angle measurements at near-sonic airspeeds. Boundary-layer cross-channel and trailing-edge radial flows caused vortices and an accumulation of low-momentum air at the hub, which may affect flow in following blade rows. Motion of a downstream rotor blade row produced pulsations in trailing-edge radial flow. The motion-picture supplement may be obtained on loan from NACA Headquarters, Washington, D.C.

Kofskey, Milton G↗
NASA NTRS1973

Liquid rocket propellant feedline dynamics

An analytical and experimental study of liquid rocket propellant feedline dynamics has been performed. The analytical model, which includes the effects of turbulent flow, distributed and local compliances, bellows, side branches, and structural mounting stiffness, was verified by an experimental program. Water was used as the internal fluid and the dynamic perturbations in pressure and flow were created by a piston pulser. Measurements were made to determine the pressure perturbation amplitude and phase at the line terminal due to a sinusoidal pulser excitation. The frequency response of the various line configurations tested were compared with the computed theoretical results.

Holster, J. L.↗
NASA NTRS1990

Unsteady inviscid and viscous computations for vortex-dominated flows

The unsteady supersonic flow around a rigid sharp-edged delta wing is solved using the unsteady Euler and thin-layer Navier-Stokes equations. The problem is formulated relative to a moving frame of reference so that computation of the grid motion is not required. A three-dimensional, implicit, aproximately factored, central-differencing, finite-volume scheme is used to obtain the time-accurate, unsteady, locally conical flow. The inviscid and viscous results are compared during the periodic response of a wing undergoing forced rolling-oscillation motion. The results show substantial differences in the surface pressure results and other distributed flow characteristics. These differences are attributed to the inviscid and viscous flow predictions in the vortex-dominated regions. The results of the total loads do not show any significant differences.

Kandil, Osama A.↗
NASA NTRS1992

A prototype heat pipe heat exchanger for the capillary pumped loop flight experiment

A Capillary Pumped Two-Phase Heat Transport Loop (CAPL) Flight Experiment, currently planned for 1993, will provide microgravity verification of the prototype capillary pumped loop (CPL) thermal control system for EOS. CAPL employs a heat pipe heat exchanger (HPHX) to couple the condenser section of the CPL to the radiator assembly. A prototype HPHX consisting of a heat exchanger (HX), a header heat pipe (HHP), a spreader heat pipe (SHP), and a flow regulator has been designed and tested. The HX transmits heat from the CPL condenser to the HHP, while the HHP and SHP transport heat to the radiator assembly. The flow regulator controls flow distribution among multiple parallel HPHX's. Test results indicated that the prototype HPHX could transport up to 800 watts with an overall heat transfer coefficient of more than 6000 watts/sq m-deg C. Flow regulation among parallel HPHX's was also demonstrated.

Ku, Jentung↗
NASA NTRS1997

Experimental Investigation of the Near Wall Flow Structure of a Low Reynolds Number 3-D Turbulent Boundary Layer

Laser Doppler velocimetry (LDV) measurements and hydrogen bubble flow visualization techniques were used to examine the near-wall flow structure of 2D and 3D turbulent boundary layers (TBLs) over a range of low Reynolds numbers. The goals of this research were (1) an increased understanding of the flow physics in the near wall region of turbulent boundary layers,(2) to observe and quantify differences between 2D and 3D TBL flow structures, and (3) to document Reynolds number effects for 3D TBLs. The LDV data have provided results detailing the turbulence structure of the 2D and 3D TBLs. These results include mean Reynolds stress distributions, flow skewing results, and U and V spectra. Effects of Reynolds number for the 3D flow were also examined. Comparison to results with the same 3D flow geometry but at a significantly higher Reynolds number provided unique insight into the structure of 3D TBLs. While the 3D mean and fluctuating velocities were found to be highly dependent on Reynolds number, a previously defined shear stress parameter was discovered to be invariant with Reynolds number. The hydrogen bubble technique was used as a flow visualization tool to examine the near-wall flow structure of 2D and 3D TBLs. Both the quantitative and qualitative results displayed larger turbulent fluctuations with more highly concentrated vorticity regions for the 2D flow.

FLOW VISUALIZATION↗
NASA NTRS1999

Numerical Prediction of Transient Axial Thrust and Internal Flows in a Rocket Engine Turbopump

This paper presents the application of the Generalized Fluid System Simulation Program (GFSSP) to model the time-dependent flow in a complex secondary flow circuit of the turbopump of the Fastrac engine currently under development at Marshall Space Flight Center. GFSSP is a general purpose computer program for analyzing steady-state and time-dependant flowrates, pressures, temperatures, and concentrations in a complex flow network. The program employs a finite volume formulation of mass, momentum and energy conservation equations in conjunction with the thermodynamic equation of state of real fluids. GFSSP was used to calculate the axial thrust and internal flow distribution of the Fastrac engine turbopump during the start and shut down transients. The models discussed in this paper use boundary conditions that were extracted from turbopump test data. The GFSSP predicted turbopump secondary flow passage pressures and temperatures were compared with actual measured values.

VanHooser, Katherine↗
NASA NTRS2002

Overview of NASA Multi-dimensional Stirling Convertor Code Development and Validation Effort

A NASA grant has been awarded to Cleveland State University (CSU) to develop a multi-dimensional (multi-D) Stirling computer code with the goals of improving loss predictions and identifying component areas for improvements. The University of Minnesota (UMN) and Gedeon Associates are teamed with CSU. Development of test rigs at UMN and CSU and validation of the code against test data are part of the effort. The one-dimensional (1-D) Stirling codes used for design and performance prediction do not rigorously model regions of the working space where abrupt changes in flow area occur (such as manifolds and other transitions between components). Certain hardware experiences have demonstrated large performance gains by varying manifolds and heat exchanger designs to improve flow distributions in the heat exchangers. 1-D codes were not able to predict these performance gains. An accurate multi-D code should improve understanding of the effects of area changes along the main flow axis, sensitivity of performance to slight changes in internal geometry, and, in general, the understanding of various internal thermodynamic losses. The commercial CFD-ACE code has been chosen for development of the multi-D code. This 2-D/3-D code has highly developed pre- and post-processors, and moving boundary capability. Preliminary attempts at validation of CFD-ACE models of MIT gas spring and "two space" test rigs were encouraging. Also, CSU's simulations of the UMN oscillating-flow fig compare well with flow visualization results from UMN. A complementary Department of Energy (DOE) Regenerator Research effort is aiding in development of regenerator matrix models that will be used in the multi-D Stirling code. This paper reports on the progress and challenges of this

Tew, Roy C.↗