Search NASA⌕ Search

SEARCH · Search NASA

Results for “FLUTTER - PROPELLERS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1977

Optimization of active control systems to suppress flutter and minimize turbulence response

A method for optimizing an active control system which will suppress flutter and minimize the response of a lifting surface to atmospheric turbulence is presented. A mathematical search method is developed which will find a control law which will cause an active control system to flutter at a specified freestream velocity, air density, and Mach number. With the flutter velocity of the system held constant, the control law is then modified in such a way that the peak output power spectral density function of the angular response of a lifting surface (as a result of atmospheric turbulence) is minimized for a specified flight velocity which is less than the flutter velocity. The von Karman generalized power spectrum for the transverse components of turbulence is used in an example problem to increase the flutter velocity and minimize the turbulence response of a simplified delta-wing model which has leading and trailing edge control surfaces.

Rudisill, C. S.↗
NASA NTRS1977

Flutter of an elastic plate under tension

The problem of flutter of a tensioned elastic plate is reconsidered on a model of two-dimensional aerodynamic flow over a one-dimensional, infinitely wide plate. The purpose is to clarify the effect of variations in plate bending stiffness on the flutter of a plate under a given tension, and vice versa. On the basis that the flutter mode for the one-dimensional infinitely wide plate is essentially the first plate natural mode for subsonic and low supersonic Mach numbers, and that the dynamic pressure required for flutter is proportional to the square of the first natural mode frequency, it is shown that the membrane paradox disappears for Mach numbers 0 and 1.3, so that reduced bending stiffness reduces the dynamic pressure required for flutter.

Dowell, E. H.↗
NASA NTRS1978

Supersonic unstalled flutter

Flutter analyses were developed to predict the onset of supersonic unstalled flutter of a cascade of two-dimensional airfoils. The first of these analyzes the onset of supersonic flutter at low levels of aerodynamic loading (i.e., backpressure), while the second examines the occurrence of supersonic flutter at moderate levels of aerodynamic loading. Both of these analyses are based on the linearized unsteady inviscid equations of gas dynamics to model the flow field surrounding the cascade. These analyses are utilized in a parametric study to show the effects of cascade geometry, inlet Mach number, and backpressure on the onset of single and multi degree of freedom unstalled supersonic flutter. Several of the results are correlated against experimental qualitative observation to validate the models.

Adamczyk, J. J.↗
NASA NTRS1978

Supersonic unstalled flutter

Recently two flutter analyses have been developed at NASA Lewis Research Center to predict the onset of supersonic unstalled flutter of a cascade of two-dimensional airfoils. The first of these analyzes the onset of supersonic flutter at low levels of aerodynamic loading (i.e., backpressure), while the second examines the occurrence of supersonic flutter at moderate levels of aerodynamic loading. Both of these analyses are based on the linearized unsteady inviscid equations of gas dynamics to model the flow field surrounding the cascade. The details of the development of the solution to each of these models have been published. The objective of the present paper is to utilize these analyses in a parametric study to show the effects of cascade geometry, inlet Mach number, and backpressure on the onset of single and multi degree of freedom unstalled supersonic flutter. Several of the results from this study are correlated against experimental qualitative observation to validate the models.

Adamczyk, J. J.↗
NASA NTRS1979

A computerized method for calculating flutter characteristics of a system characterized by two degrees of freedom

A formulation is given for calculating flutter frequency and flutter speed for a problem with two degrees of freedom. Two different solutions for evaluating the flutter determinant are presented and the results for each method are compared. A program flow diagram, partial program listing, and a sample problem with input and output for the two different methods are included. Although the method was developed for computing flutter characteristics of a pylon installed in the NASA Langley VSTOL tunnel, it is sufficiently general to solve any flutter system that can be characterized by two degrees of freedom.

Stalnaker, W. A.↗
NASA NTRS1980

Minimum mass sizing of a large low-aspect ratio airframe for flutter-free performance

A procedure for sizing an airframe for flutter-free performance is demonstrated on a large, flexible supersonic transport aircraft. The procedure is based on using a two level reduced basis or modal technique for reducing the computational cost of performing the repetitive flutter analyses. The supersonic transport aircraft exhibits complex dynamic behavior, has a well-known flutter problem and requires a large finite element model to predict the vibratory and flutter response. Flutter-free designs were produced with small mass increases relative to the wing structural weight and aircraft payload.

Greene, W. H.↗
NASA NTRS1980

Effects of angle of attack and vertical fin on transonic flutter characteristics of an arrow-wing configuration

Experimental transonic flutter results are presented for a simplified 1/50 size, aspect ratio 1.77, wind tunnel model of an arrow wing design. Flutter results are presented for two configurations; namely, one with and one without a ventral fin mounted at the 0.694 semispan station. Results are presented for both configurations trimmed to zero lift and in a lifting condition at angles of attack up to 4 deg. The results show that the flutter characteristics of both configurations are similar to those usually observed. Increasing angle of attack reduces the flutter dynamic pressure by a small amount (about 13 percent maximum) for both configurations. The addition of the fin to the basic wing increases the flutter dynamic pressure. Calculated results for both configurations in the nonlifting condition obtained by using subsonic doublet lattice unsteady aerodynamic theory correlate reasonably well with the experimental results. Calculated results for the basic wing obtained by using subsonic kernal function unsteady aerodynamic theory did not agree as well with the experimental data.

Doggett, R. V., Jr.↗
NASA NTRS1981

Final design and fabrication of an active control system for flutter suppression on a supercritical aeroelastic research wing

The final design and hardware fabrication was completed for an active control system capable of the required flutter suppression, compatible with and ready for installation in the NASA aeroelastic research wing number 1 (ARW-1) on Firebee II drone flight test vehicle. The flutter suppression system uses vertical acceleration at win buttock line 1.930 (76), with fuselage vertical and roll accelerations subtracted out, to drive wing outboard aileron control surfaces through appropriate symmetric and antisymmetric shaping filters. The goal of providing an increase of 20 percent above the unaugmented vehicle flutter velocity but below the maximum operating condition at Mach 0.98 is exceeded by the final flutter suppression system. Results indicate that the flutter suppression system mechanical and electronic components are ready for installation on the DAST ARW-1 wing and BQM-34E/F drone fuselage.

Hodges, G. E.↗
NASA NTRS1982

Transonic flutter study of a wind-tunnel model of a supercritical wing with/without winglet

The model was a 1/6.5-size, semipan version of a wing proposed for an executive-jet-transport airplane. The model was tested with a normal wingtip, a wingtip with winglet, and a normal wingtip ballasted to simulate the winglet mass properties. Flutter and aerodynamic data were acquired at Mach numbers (M) from 0.6 to 0.95. The measured transonic flutter speed boundary for each wingtip configuration had roughly the same shape with a minimum flutter speed near M=0.82. The winglet addition and wingtip mass ballast decreased the wing flutter speed by about 7 and 5 percent, respectively; thus, the winglet effect on flutter was more a mass effect than an aerodynamic effect.

Ruhlin, C. L.↗
NASA NTRS1982

Minimum mass sizing of a large low-aspect ratio airframe for flutter-free performance

A procedure for sizing an airframe for flutter-free performance is demonstrated on a large, flexible supersonic transport aircraft. The procedure is based on using a two-level reduced basis or modal technique for reducing the computational cost of performing the repetitive flutter analyses. The supersonic transport aircraft exhibits complex dynamic behavior, has a well-known flutter problem and requires a large finite-element model to predict the vibratory and flutter response. Flutter-free designs are produced with small mass increases relative to the wing structural weight and aircraft payload. In view of the ability of the resizing procedure to handle this supersonic transport configuration, it seems likely that the method could be used for many other aircraft.

Greene, W. H.↗
NASA NTRS1982

Evaluation of four subcritical response methods for on-line prediction of flutter onset in wind-tunnel tests

Four subcritical response methods were evaluated for on-line use in transonic wind-tunnel tests where the flutter model is excited solely by airstream turbulence. The methods were: randomdec, power-spectral-density, peak-hold, and cross-spectrum. Subcritical response data were obtained during tests in the Langley Transonic Dynamics Tunnel of a cantilevered flutter model wing. The test procedure was to maintain a constant Mach number and increase the dynamic pressure (q) in incremental steps. The four methods provided damping trends by which the flutter mode could be tracked and extrapolated to a flutter-onset q. A hard flutter point was obtained at M = 0.82. The peak-mold and cross-spectrum methods gave reliable results and could be most readily used for on-line testing.

Ruhlin, C. L.↗
NASA NTRS1982

Measured and calculated effects of angle of attack on the transonic flutter of a supercritical wing

The effects of angle of attack between 0 and 4 degrees were studied. The results indicate that increasing angle of attack from zero can produce substantial changes in the transonic flutter characteristics that are favorable or unfavorable depending on Mach number and angle of attack. The bottom of the transonic flutter-boundary 'bucket' is shown to occur at lower Mach number as angle of attack increases. These flutter results correlate well with the effects of Mach number and angle of attack on aerodynamic behavior, especially on the development of transonic flow phenomena. The calculated flutter characteristics are in good agreement with the experimental data at zero angle of attack, but at nonzero angles of attack the experiments show sharply declining and backward-turning transonic flutter boundaries that are not indicated by the calculations. These may be caused by variations in static aeroelastic deformation.

Yates, E. C., Jr.↗
NASA NTRS1981

Subsonic/transonic stall flutter investigation of a rotating rig

Stall flutter is investigated by obtaining detailed quantitative steady and aerodynamic and aeromechanical measurements in a typical fan rotor. The experimental investigation is made with a 31.3 percent scale model of the Quiet Engine Program Fan C rotor system. Both subsonic/transonic (torsional mode) flutter and supersonic (flexural) flutter are investigated. Extensive steady and unsteady data on the blade deformations and aerodynamic properties surrounding the rotor are acquired while operating in both the steady and flutter modes. Analysis of this data shows that while there may be more than one traveling wave present during flutter, they are all forward traveling waves.

Jutras, R. R.↗
NASA NTRS1984

Winglet effects on the flutter of twin-engine-transport type wing

Flutter characteristics of a cantilevered high aspect ratio wing with winglet were investigated. The configuration represented a current technology, twin-engine airplane. A low-speed and a high-speed model were used to evaluate compressibility effects through transonic Mach numbers and a wide range of mass-density ratios. Four flutter mechanisms were obtained in test, as well as analysis from various combinations of configuration parameters. The coupling between wing tip vertical and chordwise motions was shown to have significant effect under some conditions. It is concluded that, for the flutter model configurations studied, the winglet related flutter was amenable to the conventional flutter analysis techniques.

Bhatia, K. G.↗
NASA NTRS1984

Flutter parametric studies of cantilevered twin-engine-transport type wing with and without winglet. Volume 1: Low-speed investigations

Flutter characteristics of a cantilevered high aspect ratio wing with winglet were investigated. The configuration represented a current technology, twin-engine airplane. A low-speed and high-speed model were used to evaluate compressibility effects through transonic Mach numbers and a wide range of mass-density ratios. Four flutter mechanisms were obtained in test, as well as analysis from various combinations of configuration parameters. The coupling between wing tip vertical and chordwise motions was shown to have significant effect under some conditions. It is concluded that for the flutter model configurations studied, the winglet related flutter was amenable to the conventional flutter analysis techniques.

Bhatia, K. G.↗
NASA NTRS1986

Flight test of a decoupler pylon for wing/store flutter suppression

The decoupler pylon is a NASA concept of passive wing-store flutter suppression achieved by providing a low store-pylon pitch frequency. Flight tests were performed on an F-16 aircraft carrying on each wing an AIM-9J wingtip missile, a GBU-8 bomb near midspan, and an external fuel tank. Baseline flights with the GBU-8 mounted on a standard pylon established that this configuration is characterized by an antisymmetric limited amplitude flutter oscillation within the operational envelope. The airplane was then flown with the GBU-8 mounted on the decoupler pylon. The decoupler pylon successfully suppressed wing-store flutter throughout the flight envelope. A 37-percent increase in flutter velocity over the standard pylon was demonstrated. Maneuvers with load factors to 4g were performed. Although the static store displacements during maneuvers were not sufficiently large to be of concern, a store pitch alignment system was tested and performed successfully. One GBU-8 was ejected demonstrating that weapon separation from the decoupler pylon is normal. Experience with the present decoupler pylon design indicated that friction in the pivoting mechanism could affect its proper functioning as a flutter suppressor.

Cazier, F. W., Jr.↗
NASA NTRS1986

Flight test of a decoupler pylon for wing/store flutter suppression

The decoupler pylon is a NASA concept of passive wing-store flutter suppression achieved by providing a low store-pylon pitch frequency. Flight tests where performed on an F-16 airplane carrying on each wing an AIM-9J wingtip missile, a GBU-8 bomb near midspan, and an external fuel tank. Baseline flights with the GBU-8 mounted on a standard pylon established that this configuration is characterized by an antisymmetric limited amplitude flutter oscillation within the operational envelope. The airplane was then flown with the GBU-8 mounted on the decoupler pylon. The decoupler pylon successfully suppressed wing-store flutter thoughout the flight envelope. A 37-percent increase in flutter velocity over the standard pylon was demonstrated. Maneuvers with load factors to 4g were performed. Although the static store displacements during maneuvers were not sufficiently large to be of concern, a store pitch alignment system was tested and performed successfully. One GBU-8 was ejected demonstrating that weapon separation from the decoupler pylon is normal. Experience with the present decoupler pylon design indicated that friction in the pivoting mechanism could affect its proper functioning as a flutter suppressor.

Cazier, F. W., Jr.↗
NASA NTRS1984

Optimization of cascade blade mistuning under flutter and forced response constraints

In the development of modern turbomachinery, problems of flutter instabilities and excessive forced response of a cascade of blades that were encountered have often turned out to be extremely difficult to eliminate. The study of these instabilities and the forced response is complicated by the presence of mistuning; that is, small differences among the individual blades. The theory of mistuned cascade behavior shows that mistuning can have a beneficial effect on the stability of the rotor. This beneficial effect is produced by the coupling between the more stable and less stable flutter modes introduced by mistuning. The effect of mistuning on the forced response can be either beneficial or adverse. Kaza and Kielb have studied the effects of two types of mistuning on the flutter and forced response: alternate mistuning where alternte blades are identical and random mistuning. The objective is to investigate other patterns of mistuning which maximize the beneficial effects on the flutter and forced response of the cascade. Numerical optimization techniques are employed to obtain optimal mistuning patterns. The optimization program seeks to minimize the amount of mistuning required to satisfy constraints on flutter speed and forced response.

Murthy, D. V.↗