Search NASA⌕ Search

SEARCH · Search NASA

Results for “FOSS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Effects of Boattail Area Contouring and Simulated Turbojet Exhaust on the Loading and Fuselage-tail Component Drag of a Twin-engine Fighter-type Airplane Model

An investigation of a twin-engine fighter-type airplane model has been conducted in the Langley 16-foot transonic tunnel to determine the effect on drag of a fuselage volume addition incorporating streamline contouring and more extensive boattailing of the engine shrouds. The effect of hot exhausts from the turbojet engines was simulated with hydrogen peroxide gas generators using scaled nonafterburning engine nozzles. Afterbody pressure distributions, base drag coefficients, and forces on the fuselage-tail configurations are presented at Mach numbers from 0.80 to 1.05 angles of attack of 0 degree and 4 degrees for jet pressure ratios from 1 to 7. The effect of jet operation on both the basic and modified models was generally to decrease base pressures but to increase most other afterbody pressures and, therefore, to result in an overall decrease in fuselage-tail component drag. The addition of volume to the basic model reduced the base drag coefficient by 0.0010 with the jets off and 0.0018 at a typical cruise operating condition of a jet pressure ratio of 3, a Mach number of 0.85, and an angle of attack of 4 degrees. The overall jet-off reduction in fuselage-tail component drag due to the volume addition was a maximum of 0.0040 at a Mach number of 0.90 for an angle of attack of 4 degrees.

Foss, Willard E , Jr↗
NASA NTRS1994

Transverse vorticity measurements in the NASA Ames 80 x 120 wind tunnel boundary layer

The MSU compact four-wire transverse vorticity probe permits omega(sub z)(t) measurements in a nominally 1 sq mm domain. Note that a conventional coordinate system is used with x and y in the streamwise and normal directions respectively. The purpose of this investigation was to acquire time series data in the same access port at the ceiling of the 80 ft x 120 ft wind tunnel (NASA Ames Research Center) as earlier used by the Wallace group from the University of Maryland and to compare the present results with those of the three-component vorticity probe used in that earlier study.

Foss, John F.↗
NASA NTRS1996

Effect of a delta tab on fine scale mixing in a turbulent two-stream shear layer

The fine scale mixing produced by a delta tab in a shear layer has been studied experimentally. The tab was placed at the trailing edge of a splitter plate which produced a turbulent two-stream mixing layer. The tab apex tilted downstream and into the high speed stream. Hot-wire measurements in the 3-D space behind the tab detailed the three velocity components as well as the small scale population distributions. These small scale eddies, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. It was found that the small scale populations were greater in the shear region behind the tab, with the greatest increase occurring where the shear layer underwent a sharp turn. This location was near, but not coincident, with the core of the streamwise vortex, and away from the region exhibiting maximum turbulence intensity. Moreover, the tab increased the most probably frequency and strain rate of the small scales. It made the small scales smaller and more energetic.

Foss, J. K.↗
NASA NTRS1997

An Experimental Study of the Near Field Region of a Free Jet with Passive Mixing Tabs

An experimental study was performed to determine the flow characteristics of a tabbed free jet. Results were acquired in the near field (nominally 2 tab widths upstream to 2 tab widths downstream of the exit plane) of a tabbed jet. Upstream pressure results showed static pressure distributions in both the x-and y-directions along the top surface of the tunnel. Hot-wire measurements showed rapid expansion of the core fluid into the ambient region. Two counter rotating regions of streamwise vorticity were shown on each side of the primary tab. An enhancement of the tabbed jet concept was proposed and tested. Specifically, two tabs, half the scale of the primary tab, were added to the primary tab to provide attachment surfaces for the normally occurring ejection of fluid. The secondary tabs caused a slight increase in the streamwise vorticity created from the upstream static pressure gradient while significantly increasing the re-oriented boundary layer vorticity. The combined pumping effect of the two counter rotating regions of vorticity caused a significant increase in the transport of the jet core fluid into the surrounding region.

Bohl, D. G.↗
NASA NTRS1996

The Effect of Tabs on a Jet in a Cross-Flow

A tab placed on the leeward side of the nozzle was expected to increase jet penetration into the cross-flow. An experiment at UTRC showed insignificant effect. The primary objective of the present study was to confirm and explain the ineffectiveness. The overall approach of the study was to conduct experiments in a low-speed wind tunnel and to conduct hot-wire measurements for mean velocity and streamwise vorticity fields.

Khairul Bmq Zaman↗
NASA NTRS1997

The Effect of Vortex Generators on a Jet in a Cross-Flow

The effect of vortex generators in the form of tabs on the penetration and spreading of a jet in a cross-flow has been studied experimentally. It is found that the tab has very little effect when placed on the leeward side, i.e., on the downstream edge of the jet nozzle relative to the free-stream flow. A study of the static pressure distribution reveals significantly lower pressures on the leeward side. Thus, when placed on that side the tab does not produce a "pressure hill" of sufficient magnitude that is the primary source of streamwise vorticity in the flow field over the tab. This qualitatively explains the ineffectiveness. In comparison, there is a significant effect on the flow field when the tab is placed on the windward side, The sense of vorticity generated by the tab in the latter configuration is opposite to that of the bound vortex pair that otherwise characterizes the flow. Thus, the strength of the bound vortex pair is diminished and the jet penetration is reduced.

Zaman, K. B. M. Q.↗
NASA NTRS1999

Investigation of Dynamic Flight Maneuvers With an Iced Tailplane

A detailed analysis of two of the dynamic maneuvers, the pushover and elevator doublet, from the NASA/FAA Tailplane Icing Program are discussed. For this series of flight tests, artificial ice shapes were attached to the leading edge of the horizontal stabilizer of the NASA Lewis Research Center icing aircraft, a DHC-6 Twin Otter. The purpose of these tests was to learn more about ice-contaminated tailplane stall (ICTS), the known cause of 16 accidents resulting in 139 fatalities. The pushover has been employed by the FAA, JAA and Transport Canada for tailplane icing certification. This research analyzes the pushover and reports on the maneuver performance degradation due to ice shape severity and flap deflection. A repeatability analysis suggests tolerances for meeting the required targets of the maneuver. A second maneuver, the elevator doublet, is also studied.

VanZante, Judith Foss↗
NASA NTRS1999

NASA/FAA Tailplane Icing Program Overview

The effects of tailplane icing were investigated in a four-year NASA/FAA Tailplane Icing, Program (TIP). This research program was developed to improve the understanding, of iced tailplane aeroperformance and aircraft aerodynamics, and to develop design and training aides to help reduce the number of incidents and accidents caused by tailplane icing. To do this, the TIP was constructed with elements that included icing, wind tunnel testing, dry-air aerodynamic wind tunnel testing, flight tests, and analytical code development. This paper provides an overview of the entire program demonstrating the interconnectivity of the program elements and reports on current accomplishments.

Ratvasky, Thomas P.↗
NASA NTRS1999

In-Flight Aerodynamic Measurements of an Iced Horizontal Tailplane

The effects of tailplane icing on aircraft dynamics and tailplane aerodynamics were investigated using, NASA's modified DHC-6 Twin Otter icing research aircraft. This flight program was a major element of the four-year NASA/FAA research program that also included icing wind tunnel testing, dry-air aerodynamic wind tunnel testing, and analytical code development. Flight tests were conducted to obtain aircraft dynamics and tailplane aerodynamics of the DHC-6 with four tailplane leading-edge configurations. These configurations included a clean (baseline) and three different artificial ice shapes. Quasi-steady and various dynamic flight maneuvers were performed over the full range of angles of attack and wing flap settings with each iced tailplane configuration. This paper presents results from the quasi-steady state flight conditions and describes the range of flow fields at the horizontal tailplane, the aeroperformance effect of various ice shapes on tailplane lift and elevator hinge moment, and suggests three paths that can lead toward ice-contaminated tailplane stall. It was found that wing, flap deflection was the most significant factor in driving the tailplane angle of attack toward alpha(tail stall). However, within a given flap setting, an increase in airspeed also drove the tailplane angle of attack toward alpha(tail stall). Moreover, increasing engine thrust setting also pushed the tailplane to critical performance limits, which resulted in premature tailplane stall.

Ratvasky, Thomas P.↗
NASA NTRS1997

Optimal Configuration of an Array of Tabs for Mixing Enhancement in a Shear Layer

The large and small scale vortical motions produced by delta tabs in a two-stream shear layer have been studied experimentally. The tabs were placed at the trailing edge of a splitter plate, mounted in the test section of a wind tunnel, that produced the shear layer. Hot-wire measurements detailed the velocity, vorticity and small scale population distributions in the 3-D space behind the tabs. Small scale structures, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. The optimal tab inclination angle, theta, and the optimal spanwise spacing, S, for a multiple tab array were identified. The optimal condition was that which maximized the small scale population and generated the strongest streamwise vorticity. Increasing the tab pitch angle from flush to normal to the splitter plate increased the streamwise vorticity as well as the overall small scale population. In fact, the increase in the overall small scale population correlated strongly with the increase in streamwise vorticity intensity. The optimal conditions for peak streamwise vorticity and peak small scale population, with minimum area blockage, were determined to be theta = 45deg and S = 1.5 tab widths.

Foss, J. K.↗
NASA NTRS2000

NASA/FAA Tailplane Icing Program: Flight Test Report

This report presents results from research flights that explored the characteristics of an ice-contaminated tailplane using various simulated ice shapes attached to the leading edge of the horizontal tailplane. A clean leading edge provided the baseline case, then three ice shapes were flown in order of increasing severity. Flight tests included both steady state and dynamic maneuvers. The steady state points were 1G wings level and steady heading sideslips. The primary dynamic maneuvers were pushovers to various G-levels; elevator doublets; and thrust transitions. These maneuvers were conducted for a full range of flap positions and aircraft angle of attack where possible. The analysis of this data set has clearly demonstrated the detrimental effects of ice contamination on aircraft stability and controllability. Paths to tailplane stall were revealed through parameter isolation and transition studies. These paths are (1) increasing ice shape severity, (2) increasing flap deflection, (3) high or low speeds, depending on whether the aircraft is in a steady state (high speed) or pushover maneuver (low speed), and (4) increasing thrust. The flight research effort was very comprehensive, but did not examine effects of tailplane design and location, or other aircraft geometry configuration effects. However, this effort provided the role of some of the parameters in promoting tailplane stall. The lessons learned will provide guidance to regulatory agencies, aircraft manufacturers, and operators on ice-contaminated tailplane stall in the effort to increase aviation safety and reduce the fatal accident rate.

Ratvasky, Thomas P.↗
NASA NTRS1961

Transonic Loads Characteristics of a 3-Percent-Thick 60 deg Delta-Wing-Body

An investigation has been made in the Langley 16-foot transonic tunnel to determine the aerodynamic loading characteristics of a 3-percent-thick, aspect-ratio - 2.06, 60 deg delta-wing-body combination. The Mach number range was from 0.80 t o 1.05 and the average Reynolds number based on wing mean aerodynamic chord was 10 x 10(exp 6). The angle-of-attack range was from 0 deg to 26 deg but was limited at the highest Mach numbers by tunnel drive power. Pressure distributions, spanwise loadings, integrated wing coefficients, and tabulated pressure coefficients are presented for the range of Mach numbers and angles of attack. The results indicate that a free leading-edge separation vortex is the dominant flow-field phenomenon at all Mach numbers and that, consequently, there are only slight changes in the spanwise loadings with Mach number. There is a slight outboard shift in center of pressure with an increase in Mach number. The chord-wise position of the center of pressure varies from 46 t o 55 percent of the mean aerodynamic chord when the Mach number i s increased from 0.80 to l.05.

Swihart, John M.↗
NASA NTRS2004

In-Flight Icing Training for Pilots Using Multimedia Technology

Over the last five years, the Aircraft Icing Project of the NASA Aviation Safety Program has developed a number of in-flight icing education and training aids to support increased awareness for pilots of the hazards associated with atmospheric icing conditions. Through the development of this work, a number of new instructional design approaches and media delivery methods have been introduced to enhance the learning experience, expand user interactivity and participation, and, hopefully, increase the learner retention rates. The goal of using these multimedia techniques is to increase the effectiveness of the training materials. This paper will describe the mutlimedia technology that has been introduced and give examples of how it was used.

Burke, Kevin M.↗
NASA NTRS1993

Pathways of organic carbon oxidation in three continental margin sediments

We have combined several different methodologies to quantify rates of organic carbon mineralization by the various electron acceptors in sediments from the coast of Denmark and Norway. Rates of NH4+ and Sigma CO2 liberation sediment incubations were used with O2 penetration depths to conclude that O2 respiration accounted for only between 3.6-17.4% of the total organic carbon oxidation. Dentrification was limited to a narrow zone just below the depth of O2 penetration, and was not a major carbon oxidation pathway. The processes of Fe reduction, Mn reduction and sulfate reduction dominated organic carbon mineralization, but their relative significance varied depending on the sediment. Where high concentrations of Mn-oxide were found (3-4 wt% Mn), only Mn reduction occurred. With lower Mn oxide concentrations more typical of coastal sediments, Fe reduction and sulfate reduction were most important and of a similar magnitude. Overall, most of the measured O2 flux into the sediment was used to oxidized reduced inorganic species and not organic carbon. We suspect that the importance of O2 respiration in many coastal sediments has been overestimated, whereas metal oxide reduction (both Fe and Mn reduction) has probably been well underestimated.

NASA Discipline Exobiology↗
NASA NTRS2005

Cryogenic Performance of Trex SiC Mirror

Low cost, high performance lightweight Silicon Carbide (Sic) mirrors provide an alternative to Beryllium mirrors. A Trex Enterprises 0.25m diameter lightweight Sic mirror using its patented Chemical Vapor Composites (CVC) technology was evaluated for its optical performance. CVC Sic is chemically pure, thermally stable, and mechanically stiff. CVC technology yields higher growth rate than that of CVD Sic. NASA has funded lightweight optical materials technology development efforts involving Sic mirrors for future space based telescope programs. As part of these efforts, a Trex Sic was measured interferometrically from room temperature to 30 degrees Kelvin. This paper will discuss the test goals, the test instrumentation, test results, and lessons learned.

Foss, Colby↗
NASA NTRS2007

A Database of Supercooled Large Droplet Ice Accretions

A unique, publicly available database regarding supercooled large droplet ice accretions has been developed in NASA Glenn's Icing Research Tunnel. Identical cloud and flight conditions were generated for five different airfoil models. The models chosen represent a variety of aircraft types from the horizontal stabilizer of a large trans-port aircraft to the wings of regional, business, and general aviation aircraft. In addition to the standard documentation methods of 2D ice shape tracing and imagery, ice mass measurements were also taken. This database will also be used to validate and verify the extension of the ice accretion code, LEWICE, into the SLD realm.

VanZante, Judith Foss↗
NASA NTRS2007

A Database of Supercooled Large Droplet Ice Accretions [Supplement]

A unique, publicly available database regarding supercooled large droplet (SLD) ice accretions has been developed in NASA Glenn's Icing Research Tunnel. Identical cloud and flight conditions were generated for five different airfoil models. The models chosen represent a variety of aircraft types from the horizontal stabilizer of a large transport aircraft to the wings of regional, business, and general aviation aircraft. In addition to the standard documentation methods of 2D ice shape tracing and imagery, ice mass measurements were also taken. This database will also be used to validate and verify the extension of the ice accretion code, LEWICE, into the SLD realm.

VanZante, Judith Foss↗
NASA NTRS2012

Flow Quality Surveys in the Settling Chamber of the NASA Glenn Icing Research Tunnel (2011 Tests)

In 2011, the heat exchanger and refrigeration plant for NASA Glenn Research Center's Icing Research Tunnel (IRT) were upgraded. Flow quality surveys were performed in the settling chamber of the IRT in order to understand the effect that the new heat exchanger had on the flow quality upstream of the spray bars. Measurements were made of the total pressure, static pressure, total temperature, airspeed, and ow angle (pitch and yaw). These measurements were directly compared to measurements taken in 2000, after the previous heat exchanger was installed. In general, the flow quality appears to have improved with the new heat exchanger.

Steen, Laura E.↗