Search NASA⌕ Search

SEARCH · Search NASA

Results for “FUSELAGES - BENDING MOMENTS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

The generation of rolling moments with the superconducting solenoid model

The superconducting solenoid model is a pilot model core for levitation in a wind tunnel magnetic suspension system. This type of core would replace the ferromagnetic core typically installed in the model fuselage. For suspension purposes, the solenoid is operated upon by a set of electromagnets surrounding the wind tunnel which are to support and restrain the model at required positions and orientations under the influence of powerful aerodynamic disturbances. The subject of providing sources of magnets rolling moment for use when spanwise magnets, which can be used for winged models, are not available is covered. Several methods have emerged for generating a rolling moment based on the use of additional superconducting loops or magnetic poles positioned around or within the solenoid. Predictions of the moment capacities of superconducting loops in models sized for a large wind tunnel are presented. An existing prototype superconducting model proved a suitable vehicle for demonstrating and calibrating, at a smaller scale, some of the other roll elements based on magnetic pole devices. Calibration data are included.

Goodyear, M. J.↗
NASA NTRS1995

A guide to the use of the pressure disk rotor model as implemented in INS3D-UP

This is a guide for the use of the pressure disk rotor model that has been placed in the incompressible Navier-Stokes code INS3D-UP. The pressure disk rotor model approximates a helicopter rotor or propeller in a time averaged manner and is intended to simulate the effect of a rotor in forward flight on the fuselage or the effect of a propeller on other aerodynamic components. The model uses a modified actuator disk that allows the pressure jump across the disk to vary with radius and azimuth. The cyclic and collective blade pitch angles needed to achieve a specified thrust coefficient and zero moment about the hub are predicted. The method has been validated with experimentally measured mean induced inflow velocities as well as surface pressures on a generic fuselage. Overset grids, sometimes referred to as Chimera grids, are used to simplify the grid generation process. The pressure disk model is applied to a cylindrical grid which is embedded in the grid or grids used for the rest of the configuration. This document will outline the development of the method, and present input and results for a sample case.

Chaffin, Mark S.↗
NASA NTRS2008

Rotor Airloads Prediction Using Unstructured Meshes and Loose CFD/CSD Coupling

The FUN3D unsteady Reynolds-averaged Navier-Stokes solver for unstructured grids has been modified to allow prediction of trimmed rotorcraft airloads. The trim of the rotorcraft and the aeroelastic deformation of the rotor blades are accounted for via loose coupling with the CAMRAD II rotorcraft computational structural dynamics code. The set of codes is used to analyze the HART-II Baseline, Minimum Noise and Minimum Vibration test conditions. The loose coupling approach is found to be stable and convergent for the cases considered. Comparison of the resulting airloads and structural deformations with experimentally measured data is presented. The effect of grid resolution and temporal accuracy is examined. Rotorcraft airloads prediction presents a very substantial challenge for Computational Fluid Dynamics (CFD). Not only must the unsteady nature of the flow be accurately modeled, but since most rotorcraft blades are not structurally stiff, an accurate simulation must account for the blade structural dynamics. In addition, trim of the rotorcraft to desired thrust and moment targets depends on both aerodynamic loads and structural deformation, and vice versa. Further, interaction of the fuselage with the rotor flow field can be important, so that relative motion between the blades and the fuselage must be accommodated. Thus a complete simulation requires coupled aerodynamics, structures and trim, with the ability to model geometrically complex configurations. NASA has recently initiated a Subsonic Rotary Wing (SRW) Project under the overall Fundamental Aeronautics Program. Within the context of SRW are efforts aimed at furthering the state of the art of high-fidelity rotorcraft flow simulations, using both structured and unstructured meshes. Structured-mesh solvers have an advantage in computation speed, but even though remarkably complex configurations may be accommodated using the overset grid approach, generation of complex structured-mesh systems can require months to set up. As a result, many rotorcraft simulations using structured-grid CFD neglect the fuselage. On the other hand, unstructured-mesh solvers are easily able to handle complex geometries, but suffer from slower execution speed. However, advances in both computer hardware and CFD algorithms have made previously state-of-the-art computations routine for unstructured-mesh solvers, so that rotorcraft simulations using unstructured grids are now viable. The aim of the present work is to develop a first principles rotorcraft simulation tool based on an unstructured CFD solver.

Biedron, Robert T.↗
NASA NTRS1979

Design study results of a supersonic cruise fighter wing

A study has been conducted to explore the use of existing aerodynamic techniques to design a new supersonic cruise wing for an existing fighter wind-tunnel model. In addition to the usual wing design constraints of lift, pitching moment, and minimum drag, a ground rule was imposed that the wing had to fit on the existing fuselage. Experimental wind-tunnel results were obtained for a camber design and a reference flat wing. The flat wing was also fitted with leading-edge flaps which approximate the cruise camber design. The experimental results indicate that significant improvements in supersonic cruise capability can be obtained by a new wing designed using existing supersonic aerodynamic techniques.

Miller, D. S.↗
NASA NTRS1989

A user's manual for the method of moments Aircraft Modeling Code (AMC)

This report serves as a user's manual for the Aircraft Modeling Code or AMC. AMC is a user-oriented computer code, based on the method of moments (MM), for the analysis of the radiation and/or scattering from geometries consisting of a main body or fuselage shape with attached wings and fins. The shape of the main body is described by defining its cross section at several stations along its length. Wings, fins, rotor blades, and radiating monopoles can then be attached to the main body. Although AMC was specifically designed for aircraft or helicopter shapes, it can also be applied to missiles, ships, submarines, jet inlets, automobiles, spacecraft, etc. The problem geometry and run control parameters are specified via a two character command language input format. The input command language is described and several examples which illustrate typical code inputs and outputs are also included.

Peters, M. E.↗
NASA NTRS1994

A users manual for the method of moments Aircraft Modeling Code (AMC), version 2

This report serves as a user's manual for Version 2 of the 'Aircraft Modeling Code' or AMC. AMC is a user-oriented computer code, based on the method of moments (MM), for the analysis of the radiation and/or scattering from geometries consisting of a main body or fuselage shape with attached wings and fins. The shape of the main body is described by defining its cross section at several stations along its length. Wings, fins, rotor blades, and radiating monopoles can then be attached to the main body. Although AMC was specifically designed for aircraft or helicopter shapes, it can also be applied to missiles, ships, submarines, jet inlets, automobiles, spacecraft, etc. The problem geometry and run control parameters are specified via a two character command language input format. This report describes the input command language and also includes several examples which illustrate typical code inputs and outputs.

Peters, M. E.↗
NASA NTRS1985

Dual towline spin-recovery device

A device which corrects aerodynamic spin is described wherein a parachute exerts antispin forces on an aircraft to effect spin recovery. The dual parachute towlines and are each attached to the parachute and are attached to the rear fuselage equidistant to and on opposite sides of the aircraft centerline. As the parachute is deployed during spin, the parachute force acts through only the towing and exerts its force outboard of center on the aircraft. As a result, the parachute exerts not only an antispin torque, but additionally causes the aircraft to roll, creating a gyroscopic antispin rolling moment. The additional antispin rolling moment facilitates spin recovery by permitting a relatively smaller parachute to accomplish spin recovery equivalent to that of a larger parachute attached to the center of the rear fuselage.

White, W. L.↗
NASA NTRS1960

Experimental Determination of the Effects of Frequency and Amplitude of Oscillation on the Roll-Stability Derivatives for a 60 Degree Delta-Wing Airplane Model

A 60' delta-wing airplane model was oscillated in roll for several frequencies and amplitudes of oscillation to determine the effects of the oscillatory motion on the roll-stability derivatives for the model. The derivatives were measured at a Reynolds number of 1,600,000 for the wing alone, the wing-fuselage combination, and the complete model which included a triangular-plan-form vertical tail. Both rolling and yawing moments due to rolling velocity exhibited large frequency effects for angles of attack higher than 16 degrees. Variations in these derivatives were measured for the lowest frequencies of oscillation; as the frequency increased, the derivatives because more nearly linear with angle of attack. Both velocity derivatives were considerably different at high angles of attack from the corresponding derivatives measured by the steady-state rolling-flow technique. Rolling and yawing moments due to rolling acceleration were measured and similarly found to be highly dependent on frequency at high angles of attack. Some period and time-to-damp computations, which were made to reveal the significance of the acceleration derivatives, indicated that inclusion of the measured derivatives in the equations of motion lengthened the period of the lateral oscillation by 10 percent for a typical delta-wing airplane and increased the time to damp to one-half amplitude by 50 percent.

Fisher, Lewis R.↗
NASA NTRS1947

Longitudinal Characteristics of a Semispan Model of the Grumman Airplane Design 83 having a Sweptback Wing and of the Model with a Straight Wing as Determined from Wing-Flow Tests at Transonic Speeds, TED No. NACA DE337

An investigation has been made by the NACA wing-flow method to provide information on the relative longitudinal characteristics of a straight and sweptback wing in the transonic speed range. Tests were made of a semispan model of the Grumman airplane design 83 (XFlOF) incorporating a wing swept back 42.5deg with reference to quarter-chord line and also of the model with the swept wing replaced by a straight wing similar to that of the XF9F airplane. The airfoil sections were symmetrical 64l-series, with thickness ratios of 12 percent for the straight wing and 10 percent for the sweptback wing parallel to the stream direction. Measurements were made of normal force, chord force, and pitching moment at various angles of attack with the two wings both with and without the empennage, and with the fuselage alone. The tests covered a range of effective Mach numbers at the wing of the model from 0.65 to 1.10.

Silsby, Norman S.↗
NASA NTRS1993

Forebody vortex control with jet and slot blowing on an F/A-18

A wind tunnel test program was conducted in October, 1992, on a 6-percent F/A-18 model, to determine the most effective methods of forebody vortex control for providing increased yaw control at high angles of attack. A series of circular jet blowing configurations were investigated with variations in blowing rate, fuselage station, circumferential position, and blowing angle. Slot configurations were also tested and included variations in blowing rate, forward fuselage station, and length. The optimum jet and slot configurations were then also tested at -10 deg of sideslip. Yawing moments from both the jet and slot blowing configurations were found to have very good trends with increasing blowing rates and the maximum yaw control available at 50-deg angle of attack (where rudder power had dropped to near zero) was found to be 40 percent greater than the level provided by the rudder at 0-deg angle of attack.

Kramer, Brian R.↗
NASA NTRS1959

Longitudinal Aerodynamic Characteristics of a Wing-Body-Tail Model Having a Highly Tapered, Cambered 45 degree Swept Wing of Aspect Ratio 4 at Transonic Speeds

The longitudinal aerodynamic characteristics of a wing-body-horizontal-tail configuration designed for efficient performance at transonic speeds has been investigated at Mach numbers from 0.80 to 1.03 in the Langley 16-foot transonic tunnel. The effect of adding an outboard leading-edge chord-extension to the highly tapered 45 deg. swept wing was also obtained. The average Reynolds number for this investigation was 6.7 x 10(exp 6) based on the wing mean aerodynamic chord. The relatively low tail placement as well as the addition of a chord-extension achieved some alleviation of the pitchup tendencies of the wing-fuselage configuration. The maximum trimmed lift-drag ratio was 16.5 up to a Mach number of 0.9, with the moment center located at the quarter-chord point of the mean aerodynamic chord. For the untrimmed case, the maximum lift-drag ratio was approximately 19.5 up to a Mach number of 0.9.

West, F. E., Jr.↗
NASA NTRS1961

Transonic Investigation of Aerodynamic Characteristics of a Swept-Wing Fighter-Airplane Model with Leading-Edge Droop in Combination with Outboard Chord-Extensions and Notches

An investigation of the effects of several wing leading-edge modifications on the aerodynamic characteristics of a 45 degree swept-wing fighter-airplane model has been conducted in the Langley 16-foot transonic tunnel at low and high lifting conditions at Mach numbers from 0.85 to 1.03. The investigation included the determination of the effect on longitudinal stability and performance characteristics of wing leading-edge and chord-extension droops of 60 and 20 degrees chord-extension overhangs of 0.075c and 0.15c (where c inboard end of the 0.075c chord-extension to depths of 0.075c and 0.l25c, and indention of the model fuselage to conform partially to the supersonic area rule for a Mach number of 1.20. Lift, drag, and pitching-moment data were obtained for configurations with the tail on and off. Comparisons of data obtained from the present model with data from a configuration with leading-edge slats are included. Generally, the model wing modifications provided only slight improvements of the airplane longitudinal stability characteristics, but did substantially reduce the airplane drag coefficients at moderate and high lifting conditions.

Whitcomb, Charles F.↗
NASA NTRS1988

Measurements of pressures on the tail and aft fuselage of an airplane model during rotary motions at spin attitudes

The NASA-Langley Spin Tunnel was used to determine the empennage and aft fuselage surfaces of an aircraft model while it was rotated at spinning-event attitudes, in order to ascertain stern flow conditions and the effects of horizontal tail, as well as the wings, on the vertical tail. A substantial horizontal tail influence is noted on both sides of the vertical tail; the removal of the horizontal tail was found to change the propelling or damping moment characteristics of the vertical tail. The wing was also found to have a large influence on the magnitude of the pressures measured on both the empennage and the aft-fuselage areas.

Hultberg, Randy S.↗
NASA NTRS1989

Low-speed, high-lift aerodynamic characteristics of slender, hypersonic accelerator-type configurations

Two investigations were conducted in the Langley 14 by 22 Foot Subsonic Tunnel to determine the low-speed aerodynamic characteristics of a generic hypersonic accelerator-type configuration. The model was a delta wing configuration incorporating a conical forebody, a simulated wrap-around engine package, and a truncated conical aftbody. Six-component force and moment data were obtained over a range of attack from -4 to 30 degrees and for a sideslip range of + or - 20 degrees. In addition to tests of the basic configuration, component build-up tests were conducted; and the effects of power, forebody nose geometry, canard surfaces, fuselage strakes, and engines on the lower surface alone were also determined. Control power available from deflections of wing flaps and aftbody flaps was also investigated and found to be significantly increased during power-on conditions. Large yawing moments resulted from asymmetric flow fields exhibited by the forebody as revealed by both surface pressure data and flow visualization. Increasing nose bluntness reduced the yawing-moment asymmetry, and the addition of a canard eliminated the yawing-moment asymmetry.

Gatlin, Gregory M.↗
NASA NTRS1974

Theoretical prediction of thick wing and pylon-fuselage-fanpod-nacelle aerodynamic characteristics at subcritical speeds. Part 2: Computer program description

The procedures required to operate the thick wing and pylon-fuselage-fanpod-nacelle computer program are presented. The program computes surface velocities and pressure, section loads, and total configuration loads and pitching moment. Potential flow theory is used to compute the surface pressures and the associated lift, moment, and vortex drag. The skin friction drag is also computed.

Kojima, J.↗
NASA NTRS1980

Rolling flow wind tunnel tests of F-18 aircraft

The lateral directional characteristics of an F-18 aircraft was investigated. Aerodynamic derivatives associated with pure roll rate, or the 'p' derivatives were obtained. The model is described and the procedures used to obtain and correct the data, and a graphical presentation of the results are presented. These results include graphs of the lateral directional static stability derivatives versus angle of attack, and the lateral directional force and moment coefficients versus nondimensional roll rate. Results are presented for several configurations including complete, complete without vertical tails, complete without horizontal tails, fuselage wing and fuselage alone. Each of these configuations was tested with and without wing leading edge extensions. The basic control surfaces were deflected and the results were investigated.

Lutze, F. H.↗
NASA NTRS1958

Effect of Nose Length, Fuselage Length, and Nose Fineness Ratio on the Longitudinal Aerodynamic Characteristics of Two Complete Models at High Subsonic Speeds

An investigation has been made of the effects of nose length, fuselage length, and nose fineness ratio on the static longitudinal aerodynamic characteristics of an airplane model with a swept wing and low tail and of a second model with a highly tapered wing of moderate sweep and a T-tail. The tests were conducted in the Langley high-speed 7- by 10-foot tunnel at Mach numbers from 0.60 to 0.92. The nose and body cross sections were circular. For either the model with the swept wing and low tail or the model with the highly tapered wing of moderate sweep and the T-tail, the effects of forebody changes amounted primarily to rotations of the pitching-moment curves (changes in static margin) over the test ranges of angle of attack and Mach number. For the range of body shapes investigated the longitudinal stability at low lift is decreased by an increase in nose length or in fuselage length or by a reduction in nose fineness ratio when the fuselage length is held constant. In general, the stability for all model configurations showed substantially the same variation with changes in forebody area moment. The forebody changes did not alter the angle of attack at which an unstable break occurred in the moment contribution of the T-tail but did alter somewhat the magnitude of the instability.

Goodson, Kenneth W.↗