Search NASA⌕ Search

SEARCH · Search NASA

Results for “Fast Flux”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Investigation of temperature dependence of fracture toughness in high-dose HT9 steel using small-specimen reuse technique

The temperature dependence of fracture toughness in HT9 steel irradiated to 3–145 dpa at 380–503 degrees*C was investigated using miniature three-point bend (TPB) fracture specimens. A miniature-specimen reuse technique has been established: the tested halves of subsize Charpy impact specimens with dimensions of 27 mm *3mm* 4 mm were reused for this fracture test campaign by cutting a notch with a diamond-saw in the middle of each half, and by fatigue-precracking to generate a sharp crack tip. It was confirmed that the fracture toughness of HT9 steel in the dose range depends more strongly on the irradiation temperature than the irradiation dose. At an irradiation temperature <430 *degreesC, the fracture toughness of irradiated HT9 increased with the test temperature, reached an upper shelf of 180—200 MPa*m^.5 at 350–450 degrees*C, and then decreased with the test temperature. At an irradiation temperature >430 degrees*C, the fracture toughness was nearly unchanged up to about 450 *degreesC and decreased slowly with test temperatures in a higher temperature range. Such a rather monotonic test temperature dependence after high-temperature irradiation is similar to that observed for an archive material generally showing a higher degree of toughness. A brittle fracture without stable crack growth occurred in only a few specimens with relatively lower irradiation and test temperatures. In this discussion, these TPB fracture toughness data are compared with previously published data from 12.7 mm diameter disc compact tension (DCT) specimens.

Baek, Jong-Hyuk↗

High energy X-ray diffraction study of the relationship between the macroscopic mechanical properties and microstructure of irradiated HT-9 steel

Samples harvested from an HT-9 fuel test assembly (ACO-3) irradiated for six years in the Fast Flux Test Facility (FFTF) reaching 2–147 dpa at 382–504°C were deformed in-situ while collecting high-energy X-ray diffraction data to monitor microstructure evolution. With the initiation of plastic deformation, all samples exhibited a clear load transfer from the ferrite matrix to carbide particulate. This behavior was confirmed by modeling of the control material. The evolution of dislocation density in the material as a result of deformation was characterized through full pattern line profile analysis. The dislocation densities increased substantially after deformation, the level of dislocation evolution observed was highly dependent upon the irradiation temperature of the sample. The differences in both the yield and hardening behavior between samples irradiated at higher and lower temperatures suggest the existence of a transition in tensile behavior at an irradiation temperature near 420°C dividing regions of distinct damage effects.

36 MATERIALS SCIENCE↗

HT9 swelling in high burnup fast reactor fuel pin components

The irradiation-induced void swelling of HT9 stainless steel has been observed many times, but there are little data available to quantify the amount of swelling expected as a function of neutron exposure and temperature. This is further complicated by potential heat-to-heat chemical variations or heat treatment conditions during fabrication. Herein, this paper summarizes the results of most of the relevant previously completed studies, then focuses on the swelling behavior of HT9 mixed-oxide fuel cladding and wrapper wire irradiated to high neutron exposures. Note that the hexagonal duct used for the ACO-3 experiment (in the Fast Flux Test Facility, or FFTF) was also made from HT9 and has been studied previously by other researchers. The cladding enables a wider range of operating temperatures. Immersion density and transmission electron microscopy were used to identify a peak in the amount of swelling located axially, just below core centerline, for both the cladding and the wire. The peak roughly coincided with a peak seen in the cladding diameter profile. The wrapper wire showed enhanced swelling compared to the cladding, likely due to over-tempering during wire fabrication heat treatment. The grains showed decreased martensitic structure were larger in size. These data do not provide for the means to fully characterize the swelling of HT9, but do provide further insight into the factors controlling it. The onset of breakaway swelling was not indicated in this data.

36 MATERIALS SCIENCE↗

Thermal analysis of projected molten salt compositions during FFTF and EBR-II used nuclear fuel processing

This work studies the change in liquidus temperature of the salt used in the Mk-IV electrorefiner at the Idaho National Laboratory during processing campaigns of sodium-bonded driver fuels from Experimental Breeder Reactor II and the Fast Flux Test Facility reactor. Modeling and Simulation Tool for Electrochemical Recycling Systems (MASTERS), an INL proprietary pyroprocessing flowsheet simulation tool, was used to simulate the processing campaigns and determine the resulting composition changes of the Mark-IV electrorefiner salt. Surrogate salt samples simulating the Mk-IV electrorefiner salt during the fuel processing campaigns were prepared, and the thermal properties were measured via differential scanning calorimetry. Results from this study indicate that after processing approximately 2,150 kg of uranium metal from used fuel, the liquidus temperature of the molten salt exceeds 520°C, which is a significant increase from 352°C (the melting temperature of eutectic LiCl-KCl). It was also discovered that the liquidus temperature is strongly dependent on the amount of NaCl accumulating in the Mk-IV electrorefiner salt. Thus, the assessment of the liquidus temperature during the subsequent fuel processing campaigns can be simplified by considering the ternary LiCl-KCl-NaCl system only.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Post-irradiation examinations of annular mixed oxide fuels with average burnup 4 and 5% FIMA

In this paper, we present post-irradiation examination results on two type of annular mixed oxide fuel pins irradiated in the Fast Flux Test Facility (FFTF) sodium cooled reactor to an average burnup between 4% and 5% fission of initial heavy atom (FIMA). The pins differed only from the initial Pu content, which was 22 wt% and 26 wt%, respectively. The overall performance of the pins was excellent, in line with previous historical results. The pins with higher Pu content experienced higher irradiation temperatures which influenced the fission gas release, fuel swelling, and Cs distribution compared to the other pins. All the post-irradiation examinations results are discussed against the irradiation parameters. In particular, the pins with higher initial Pu content, i.e., 26 wt%, experienced higher power that resulted in enhanced fission gas release compared to the other two pins with 22 wt% initial Pu content. For the pins with higher fission gas release, onset of Cs redistribution was observed. The two pins that had lower initial Pu content and burnup showed a Cs axial distribution similar to the as-produced one.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The application of synchrotron micro-computed tomography to characterize the three-dimensional microstructure in irradiated nuclear fuel

This research demonstrated the first time that synchrotron X-ray micro-computed tomography (μ-CT) was utilized to analyze the three-dimensional (3-D) morphology of the microstructure of irradiated nuclear fuel. Both absorption contrast and propagation-based phase contrast enhanced μ-CT techniques were evaluated. Porosity and phase region volumes were determined in neutron irradiated uranium 10 wt.% zirconium (U-10Zr) using propagation-based phase contrast enhanced μ-CT. Volumes were determined by image processing software and algorithms, with the porosity volume subsequently compared to the ASTM E562 method. The 3-D porosity of a small region (~ 8 x 10 5 µm 3 ) located in the intermediate fuel redistribution zone that was removed via a focused ion beam was determined to be 7.2% via image processing. A detailed 3-D analysis of the porosity with respect to volume and morphology was provided. Five growth stages of pore evolution were observed including: nucleation, growth, coalescence, interconnected porosity, and extended/interconnected porosity. Four distinct phase regions were identified, including the pores, via both absorption contrast and propagation-based phase contrast enhanced μ-CT. A quantitative comparison of fuel swelling between this localized microscopic U-10Zr fuel region, previously irradiated in the Fast Flux Test Facility, and historic U-10Zr fuels irradiated in the Experimental Breeder Reactor-II (EBR-II) was conducted. It was determined that for similar burnups, the localized swelling in this microscopic fuel region was 7.7%, which was approximately one-half of the value of the macroscopic swelling reported in EBR-II irradiated fuel. With the advent of new specimen preparation tools for irradiated materials, as well as advances in characterization techniques, researchers can now obtain previously inaccessible microstructural insight into irradiated fuels. This possibility naturally lends itself to improved fuel performance models for the nuclear community.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Transmission electron microscopy study of a high burnup U-10Zr metallic fuel

To support the development of U-10 wt.% Zr (U-10Zr) metallic fuel for Gen IV sodium-cooled fast reactors, we analysed a solid, Na-bonded, U-10Zr (by weight percent) fuel cross section that was irradiated to a burnup of ~ 12.4 % at.% at the Fast Flux Test Facility (FFTF). Advanced characterization techniques, including site specific sample preparation by focused ion beam (FIB) and phase/chemical determination by transmission electron microscopy (TEM), were used to reveal the constituent redistribution of Zr, characterize the fuel phases and the secondary phases (such as solid fission products) present at the end of life. It is shown that the fuel pin cross section is divided into three major concentric zones: a Zr-rich central region, a Zr-lean intermediate region, and a Zr intermediate peripherical region. The phase characterization revealed that the irradiation environment enhanced the development and stabilization of phases not predicted by the standard equilibrium U-Zr phase diagrams. Comparing the current results with the ones from previous studies, it is reaffirmed that the irradiation temperature and the time spent in the reactor, rather than the fuel burnup, are the two factors that most influence the formation of redistribution zones and their extension along the fuel cross section. Various solid fission products precipitated inside the fission gas pores, such as lanthanides, ZrRu, BaTe, CsI, and Ba and Sr oxides. Here, this study provides unprecedented nanoscale understandings in the U-10Zr fuel system that may benefit fuel performance modelling and advanced fuel development.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The effect of temperature and burnup on U-10Zr metallic fuel chemical interaction with HT-9: A SEM-EDS study

The fuel cladding chemical interaction (FCCI) between Uranium-Zirconium-based metallic fuel and cladding materials during in-pile service is one of the most constraining phenomena affecting the performance of this fuel system. In this study, we investigated the effect of temperature and burnup on the FCCI development in two U-10 wt.% Zr (U-10Zr) fuel samples with HT-9 cladding irradiated as part of the MFF-3 irradiation test in the Fast Flux Test Facility (FFTF). One sample achieved a burnup of 13.1 at.% and operated with an average inner cladding temperature of 530°C, while the other achieved a burnup of 8.5 at.% and was subjected to an average inner cladding temperature of 615°C. Automated scanning electron microscopy (SEM) back-scattered electron (BSE) imaging of entire fuel cross-sections and SEM energy dispersive x-ray spectroscopy (EDS) analysis on specific fuel-cladding interface regions successfully provided a comprehensive characterization of the depth and type of interaction happening under different irradiation conditions. Further, our analysis shows that FCCI development on both fuel and cladding side is strongly influenced by the inner cladding temperature and, to some extent, the formation and integrity of Zr-rich layers between the fuel and cladding, while the impact of burnup and power is negligible. Measured FCCI thicknesses were compared to BISON simulations using both an empirical model based upon legacy data from the Experimental Breeder Reactor II (EBR II) irradiations and a mechanistic model currently under development for the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, showing satisfactory agreement. Nonetheless, this comparison supports the need for additional microstructural characterization in intermediate ranges of temperature, power, and burnups in prototypic-length pins.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Impact of composition modification induced by ion beam Coulomb-drag effects on the nanoindentation hardness of HT9

Accelerator-based ion irradiation is commonly used to simulate neutron damage, in lieu of neutron irradiation due to limited availability of fast flux facilities and little to no activation of the samples. Neutron atypical effects, however, must be recognized and their impact minimized in order to achieve the most accurate microstructural evolution under ion bombardment. Mechanical property changes, which arise from the synergy of numerous radiation-induced changes, are especially susceptible to these neutron atypical effects. Of these effects, a recently studied neutron atypical effect, arising from Coulomb-drag of vacuum contaminants and subsequent compositional alteration, was shown to substantially suppress swelling. Through the use of an ion beam filtering system, the resulting void swelling was shown to closely match neutron irradiation data. In this study, the impact of compositional modification via Coulomb-drag on the mechanical property changes is examined through the use of nanoindentation on a ferritic/martensitic alloy, HT9, irradiated with and without the use of the ion beam filtering system.

36 MATERIALS SCIENCE↗

Development and preliminary validation of a mechanistic multiscale model for fuel-cladding chemical interaction in metallic nuclear fuels

Despite decades of fuel rod material and design improvements, fuel-cladding chemical interaction (FCCI) remains the single-most lifetime-limiting behavior for modern metallic fuel rods. Constraining fuel lifetime increases operating costs, limiting the economic viability of commercializing metallic nuclear fuel technology. A mechanistic multiscale model utilizing the finite element method-based MARMOT and BISON codes was developed to more confidently predict cladding-side FCCI and its impact on fuel performance. The new BISON model incorporates mesoscale models for the effects of fuel microstructure evolution on the transport of wastage-inducing lanthanides through the fuel and for the kinetics of cladding wastage layer growth. The mesoscale models, in turn, build on lanthanide transport property data obtained from the atomistic scale. Preliminary validation studies using wastage thickness and cladding profilometry data from four fuel rods irradiated in Experimental Breeder Reactor II experiment X447 and one fuel rod from Fast Flux Test Facility experiment IFR1 show that the new model predicts cladding wastage and its effects on cladding deformation as well as existing empirical FCCI correlations. The new model is expected to aid in the design of new metallic fuel concepts, including fuel additives, cladding liners, and sodium-free annular fuel geometries. In conclusion, future work will focus on broader validation and refinement of the model’s treatment of different fuel alloys and cladding materials.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of multi-objective core optimization framework and application to sodium-cooled fast test reactors

The optimization of a Sodium-cooled Fast Reactor (SFR) core is a challenging process, due to the large number of design parameters, the nonlinearities among inputs and outputs, and the complicated correlation among output parameters. This study attempts to develop a generalized framework for the SFR core optimization by coupling the sensitivity analysis, advanced optimization algorithm, and optionally the surrogate modeling. The framework is built based on the fast reactor modeling capability of the Argonne Reactor Computation (ARC) suite and the sensitivity analysis and optimization modules embedded in the DAKOTA code, both have been integrated within the NEAMS Workbench. The genetic algorithm is selected as the optimization method for its robustness, while the option of surrogate modeling is also explored to alleviate the computational burden caused by employing the ARC direct core physics simulation and thus enhance the efficiency of the optimization. Finally, the normalized deviations of performance parameters of the near-optimal solution from those of the ideal core are calculated and used as criteria to down select the final core design. The developed framework is applied to the Advanced Burner Test Reactor (ABTR) core, and optimal solutions are determined by balancing various objectives simultaneously, including peak fast flux, core volume, power, reactivity swing, plutonium mass feed, while at the same time satisfying the predefined constraints due to safety or economics considerations. The optimal ABTR core design obtained using the direct physical simulation and surrogated model are compared and discussed. It is found that using the accurately constructed surrogate models can significantly reduce the required computational time while maintaining satisfactory accuracy.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Emulation of reactor irradiation damage using ion beams

The continued operation of existing light water nuclear reactors and the development of advanced nuclear reactor depend heavily on understanding how damage by radiation to levels degrades materials that serve as the structural components in reactor cores. The first high dose ion irradiation experiments on a ferritic-martensitic steel showing that ion irradiation closely emulates the full radiation damage microstructure created in-reactor are described. Ferritic-martensitic alloy HT9 (heat 84425) in the form of a hexagonal fuel bundle duct (ACO-3) accumulated 155 dpa at an average temperature of 443°C in the Fast Flux Test Facility (FFTF). Using invariance theory as a guide, irradiation of the same heat was conducted using self-ions (Fe++) at 5 MeV at a temperature of 460°C and to a dose of 188 displacements per atom. The void swelling was nearly identical between the two irradiation and the size and density of precipitates and loops following ion irradiation are within a factor of two of those for neutron irradiation. The level of agreement across all of the principal microstructure changes between ion and reactor irradiation establishes the capability of tailoring ion irradiation to emulate the reactor-irradiated microstructure.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Magnetic reconnection process in transient coaxial helicity injection

The physics of magnetic reconnection and fast flux closure in transient coaxial helicity injection experiments in NSTX is examined using resistive MHD simulations. These simulations have been performed using the NIMROD code with fixed boundary flux (including NSTX poloidal coil currents) in the NSTX experimental geometry. Simulations show that an X point is formed in the injector region, followed by formation of closed flux surfaces within 0.5 ms after the driven injector voltage and injector current begin to rapidly decrease. As the injector voltage is turned off, the field lines tend to untwist in the toroidal direction and magnetic field compression exerts a radial J × B force and generates a bi-directional radial E{sub toroidal}×B{sub poloidal} pinch flow to bring oppositely directed field lines closer together to reconnect. At sufficiently low magnetic diffusivity (high Lundquist number), and with a sufficiently narrow injector flux footprint width, the oppositely directed field lines have sufficient time to reconnect (before dissipating), leading to the formation of closed flux surfaces. The reconnection process is shown to have transient Sweet-Parker characteristics.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Physics of forced magnetic reconnection in coaxial helicity injection experiments in National Spherical Torus Experiment

We numerically examine the physics of fast flux closure in transient coaxial helicity injection (CHI) experiments in National Spherical Torus Experiment (NSTX). By performing resistive Magnetohydrodynamics (MHD) simulations with poloidal injector coil currents held constant in time, we find that closed flux surfaces are formed through forced magnetic reconnection. Through a local Sweet-Parker type reconnection with an elongated current sheet in the injector region, closed flux surfaces expand in the NSTX global domain. Simulations demonstrate outflows approaching poloidally Alfvénic flows and reconnection times consistent with the Sweet-Parker model. Critical requirements for magnetic reconnection and flux closure are studied in detail. These primary effects, which are magnetic diffusivity, injector flux, injector flux footprint width, and rate of injector voltage reduction, are simulated for transient CHI experiments. The relevant time scales for effective reconnection are τ{sub V}<τ{sub rec}≈τ{sub A}√(S)(1+Pm){sup 1/4}<τ{sub R}, where τ{sub V} is the time for the injector voltage reduction, τ{sub A} is the poloidal Alfvén transit time, τ{sub R} is the global resistive diffusion time, and Pm and S are Prandtl and Lundquist numbers.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

THE SHOCKING TRUTH: THE SMALL CONTRIBUTION TO HYDROGEN REIONIZATION FROM GRAVITATIONAL INFALL

It is commonly thought that stars are responsible for reionizing the universe. However, deep searches for star-forming galaxies during the epoch of reionization have not yet found sufficient galaxies to provide the necessary ionizing flux. Fast accretion shocks associated with gravitational infall of baryons during the formation of galaxies have recently been proposed as an alternative method of generating the required ionizing photons. Here we assess the contribution to hydrogen reionization from shocked gas associated with gravitational infall. We find that shocks can ionize no more than a few percent of the cosmic hydrogen by z {approx} 6. However, the small fraction of ionizing radiation produced by fast accretion shocks would be significantly more biased than that associated with stars, leading to a modification of the luminosity weighted source clustering by {approx}10%. This modification of the bias may be measurable with future precision experiments utilizing the redshifted 21 cm line to study the distribution of hydrogen during the reionization era.

79 ASTRONOMY AND ASTROPHYSICS↗

EVOLUTION OF MAGNETIC FIELD AND ENERGY IN A MAJOR ERUPTIVE ACTIVE REGION BASED ON SDO/HMI OBSERVATION

We report the evolution of the magnetic field and its energy in NOAA active region 11158 over five days based on a vector magnetogram series from the Helioseismic and Magnetic Imager (HMI) on board the Solar Dynamic Observatory (SDO). Fast flux emergence and strong shearing motion led to a quadrupolar sunspot complex that produced several major eruptions, including the first X-class flare of Solar Cycle 24. Extrapolated nonlinear force-free coronal fields show substantial electric current and free energy increase during early flux emergence near a low-lying sigmoidal filament with a sheared kilogauss field in the filament channel. The computed magnetic free energy reaches a maximum of {approx}2.6 Multiplication-Sign 10{sup 32} erg, about 50% of which is stored below 6 Mm. It decreases by {approx}0.3 Multiplication-Sign 10{sup 32} erg within 1 hr of the X-class flare, which is likely an underestimation of the actual energy loss. During the flare, the photospheric field changed rapidly: the horizontal field was enhanced by 28% in the core region, becoming more inclined and more parallel to the polarity inversion line. Such change is consistent with the conjectured coronal field 'implosion' and is supported by the coronal loop retraction observed by the Atmospheric Imaging Assembly (AIA). The extrapolated field becomes more 'compact' after the flare, with shorter loops in the core region, probably because of reconnection. The coronal field becomes slightly more sheared in the lowest layer, relaxes faster with height, and is overall less energetic.

79 ASTRONOMY AND ASTROPHYSICS↗

Experimental advances with the QICK (Quantum Instrumentation Control Kit) for superconducting quantum hardware

The Quantum Instrumentation Control Kit (QICK) is a standalone open-source qubit controller that was first introduced in 2022. In this follow-up work, we present recent upgrades to the QICK and the experimental use cases they uniquely enabled for superconducting qubit systems. These include multiplexed signal generation and readout, mixer-free readout, predistorted fast flux pulses, and phase-coherent pulses for parametric operations, including high-fidelity parametric entangling gates. We explain in detail how the QICK was used to enable these experiments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Overview of the ultrasonic instrumentation research in the MYRRHA project

The Belgian Nuclear Research Centre SCK.CEN is in the process of developing MYRRHA, a new generation IV fast flux research reactor to replace the aging BR2. MYRRHA is conceptualized as an accelerator driven system cooled with lead bismuth eutectic mixture (LBE). As LBE is opaque to visual light, ultrasonic measurement techniques are employed as the main technology to provide feedback where needed. This paper we will give an overview of the R and D at SCK.CEN with respect to ultrasonic instrumentation in heavy liquid metals. High temperature ultrasonic transducers are deployed into the reactor to generate and receive the required ultrasonic signals. The ultrasonic waves are generated and sensed by means of a piezo-electric disc at the heart of the transducer. The acoustic properties of commonly used piezo-electric materials match rather well with the acoustic properties of heavy liquid metals, simplifying the design and construction of high bandwidth ultrasonic transducers for use in heavy liquid metals. The ultrasonic transducers will operate in a liquid metal environment, where radiation and high temperature limit the choice of materials for construction. Moreover, the high surface tension of the liquid metal hinders proper wetting of the transducer, required for optimal transmission and reception of the ultrasonic waves. In a first part of the paper, we will discuss the effect of these parameters on the performance of the overall ultrasonic system. In the second part of the paper, past, present and future ultrasonic experiments in LBE will be reviewed. We will show the results of an experiment where a transducer is scanned near the free surface of an LBE pool to render ultrasonic images of objects submerged in the heavy liquid metal. Additionally, the preliminary results of an ongoing experiment that measures the evolution of LBE wetting on different types of metals and various surface conditions will be reported. The evolution of wetting is an important parameter to assess the performance of ultrasonic systems that are submerged in LBE over longer time periods. In the last part we will briefly present the overall design of the two main ultrasonic systems that will be deployed in MYRRHA: the ultrasonic fuel identification system and the ultrasonic lost fuel localization system. (authors)

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗