Search NASA⌕ Search

SEARCH · Search NASA

Results for “Forced Oscillation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Study of the force coefficients on plates using an open source numerical wave tank

An open source numerical wave tank based on the OpenFOAM® software was setup and tested to solve the Navier-Stokes equations. This work focused on submerged plates because of their simple geometry, their importance as a design component (e.g., heave plates), and the broad availability of published experimental results. Two-dimensional plates in an oscillatory flow, as well as three-dimensional circular disks and square plates undergoing forced oscillations were simulated in conditions where the nonlinearity of hydrodynamic viscous drag and inertia forces can be probed easily. The effect of plate thickness as well as the ability of the numerical simulations to predict wave radiation damping at shallow plate submergence were also considered. Overall, force coefficient predictions were very satisfactory when compared to experimental data, and generally exhibited less scatter. Here, the influence of both Keulegan-Carpenter number and frequency parameter on the hydrodynamic force could be assessed as well from these numerical simulations as from past laboratory experiments.

13 HYDRO ENERGY↗

Non-linear dynamic response of a wind turbine blade

The paper outlines the nonlinear dynamic analysis of an isolated three-degree flap-lag-feather wind turbine blade under a gravity field and with shear flow. Lagrangian equations are used to derive the nonlinear equations of motion of blade for arbitrarily large angular deflections. The limit cycle analysis for forced oscillations and the determination of the principal parametric resonance of the blade due to periodic forces from the gravity field and wind shear are performed using the harmonic balance method. Results are obtained first for a two-degree flap-lag blade, then the effect of the third degree of freedom (feather) is studied. The self-excited flutter solutions are obtained for a uniform wind and with gravity forces neglected. The effects of several parameters on the blade stability are examined, including coning angle, structural damping, Lock number, and feather frequency. The limit cycle flutter solution of a typical configuration shows a substantial nonlinear softening spring behavior.

Chopra, I.↗

Shear Strength and Release of Large Cryogenic Pellets from the Barrel of a Shattered Pellet Injector for Disruption Mitigation

Shattered pellet injection (SPI) has been chosen as the baseline disruption mitigation system on ITER due to its ability to rapidly inject material deep into the plasma to greatly increase the plasma density and radiate the thermal energy. SPI utilizes a mechanical punch or high-pressure gas to release and accelerate a pellet that has been cryogenically desublimated in the barrel of a pipe gun. Various material injection combinations could possibly be implemented during different phases of a disruption event to radiate plasma energy, reduce electromagnetic loads on machine components, avoid the formation of runaway electrons, or to dissipate runaway electrons that form. Each injection phase could possibly utilize combinations of deuterium, neon, or argon. In this paper we outline experimental measurements of pellet material shear strength at SPI operating temperatures to understand the force needed to release SPI pellets. Deuterium, neon, argon, and deuterium-neon mixture pellets with diameters of 8.5, 12.5, and 15.7 mm are formed at a range of relevant gas pressures and temperatures and dislodged from the cold zone with a slow-moving piston driven by a motor. The slow-moving piston is kept above the triple point temperature of the material while the pellet is forming, then cooled to below the triple point temperature before contacting the pellet to minimize any thermal conduction to the pellet. The piston incorporates a load cell to measure the force applied when the pellet breaks away from the cold zone in the barrel.The ability of the gas and punch methods to exceed the shear strength of the studied pellet materials for release has been analyzed. High pressure gas delivered by fast opening valves produce pressure shock to the pellet due to supersonic expansion of the propellant gas. Pressure (and therefore, force) oscillations are present due to transverse density propagation throughout the breech volume. Mechanical punches deliver an impact force through a high-kinetic energy impact. The effect of the mechanical shock on the pellet has been explored and will be presented in this paper. Scaling to larger ITER size SPI pellets will be described.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Interface dynamics of a two-component Bose-Einstein condensate driven by an external force

The dynamics of an interface in a two-component Bose-Einstein condensate driven by a spatially uniform time-dependent force is studied. Starting from the Gross-Pitaevskii Lagrangian, the dispersion relation for linear waves and instabilities at the interface is derived by means of a variational approach. A number of diverse dynamical effects for different types of driving force is demonstrated, which includes the Rayleigh-Taylor instability for a constant force, the Richtmyer-Meshkov instability for a pulse force, dynamic stabilization of the Rayleigh-Taylor instability and onset of the parametric instability for an oscillating force. Gaussian Markovian and non-Markovian stochastic forces are also considered. It is found that the Markovian stochastic force does not produce any average effect on the dynamics of the interface, while the non-Markovian force leads to exponential perturbation growth.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Dynamical Casimir-Polder force in a one-dimensional cavity with quasimodes

In this article, we consider the dynamic Casimir-Polder force between an atom and a conducting wall in a one-dimensional cavity. Using quasimode theory to describe the dissipation of the electromagnetic fields in the cavity, our investigation shows that the force oscillations are damped in a short time, and tend to a final, steady, negative value. We discuss in detail the effects on the force of the quasimode decay rate, the cavity size, and the atom-wall distance.

74 ATOMIC AND MOLECULAR PHYSICS↗

Acoustically induced oscillation and rotation of a large drop in space

A 2.5 cm diameter water drop was successfully deployed and manipulated in a triaxial acoustic resonance chamber during a 240 sec low-gravity SPAR rocket flight. Oscillation and rotation were induced by modulating and phase shifting the signals to the speakers. Portions of the film record were digitized and analyzed. Spectral analysis brought out the n = 2, 3, 4 free oscillation modes of the drop, its very low-frequency center-of-mass motion in the acoustic potential well, and the forced oscillation frequency. The drop boundaries were least-square fitted to general ellipses, providing eccentricities of the distorted drop. The normalized equatorial area of the rotating drop was plotted vs a rotational parameter, and was in excellent agreement with values derived from the theory of equilibrium shapes of rotating liquid drops.

Jacobi, N.↗

Unsteady supersonic flow around delta wings with symmetric and asymmetric flaps oscillation

A parametric study is presented to investigate the effect of reduced frequency of the leading-edge flaps on the locally-conical, unsteady, supersonic flow around a delta wing. This study covers symmetric and antisymmetric forced oscillation of the leading-edge flaps. The effects of the freestream Mach number and angle of attack are also presented. The problem is solved using time-accurate integration of the unsteady, compressible, thin-layer Navier-Stokes equations and the unsteady, linearized, Navier-displacement equations. The delta wing is of aspect ratio of 1.5 and its leading-edge flaps are hinged at 65 percent of the local-half span length. The reduced frequency is varied between 2 pi and pi/2. Two supersonic flow conditions have been investigated; the first is for a freestream Mach number of 2.4 and an angle of attack of 19 deg and the second is for a freestream Mach number of 1.5 and an angle attack of 15 deg.

Kandil, Osama A.↗

Subsonic and Transonic Dynamic Stability Characteristics of the X-33

Dynamic stability testing was conducted on a 2.5% scale model of the X-33 technology demonstrator sub-orbital flight-test vehicle. This testing was conducted at the NASA Langley Research Center (LaRC) l6-Foot Transonic Wind Tunnel with the LaRC High-speed Dynamic Stability system. Forced oscillation data were acquired for various configurations over a Mach number range of 0.3 to 1.15 measuring pitch, roll and yaw damping, as well as the normal force due to pitch rate and the cross derivatives. The test angle of attack range was from -2 to 24 degrees, except for those cases where load constraints limited the higher angles of attack at the higher Mach numbers. A variety of model configurations with and without control surfaces were employed, including a body alone configuration. Stable pitch damping is exhibited for the baseline configuration throughout the angle of attack range for Mach numbers 0.3, 0.8, and 1.15. Stable pitch damping is present for Mach numbers 0.9 and 0.6 with the exception of angles 2 and 16 degrees, respectively. Constant and stable roll damping were present for the baseline configuration over the range of Mach numbers up to an angle of attack of 16 degrees. The yaw damping for the baseline is somewhat stable and constant for the angle of attack range from -2 to 8 degrees, with the exception of Mach numbers 0.6 and 0.8. Yaw damping becomes highly unstable for all Mach numbers at angles of attack greater than 8 degrees.

Tomek, D.↗

Shock-Buffet Prediction Report in Support of the High Angle Working Group at the Third Aeroelastic Prediction Workshop

This paper presents a summary of the computational shock-buffet results associated with the third Aeroelastic Prediction Workshop (AePW-3) High-Angle Working Group. The computational results are compared against experimental data collected during the Oscillating Turn Table (OTT) Benchmark Supercritical Wing (BSCW) test campaign conducted in NASA Langley Research Center Transonic Dynamics Tunnel (TDT) in early 2000. In addition to experimental forced oscillation data, unsteady pressure data was collected at a single spanwise station at transonic Mach numbers, several values of dynamic pressure, and fixed angles of attack. It is acknowledged that the current experimental data are limited, but future experiments are planned to obtain pressure data at two wingspan stations in addition to unsteady Pressure Sensitive Paint (uPSP). With that, the computational results presented here are considered to be semi-blind. The results are presented in the form of time-varying pressure coefficients, running-mean values of the pressure coefficients, Power Spectral Density (PSD) and Strouhal number computations. The results are split into two parts. In the first part, the computational results obtained by each team using their flow solvers and grids are compared. In the second part, a single computational tool was used to compute unsteady pressure on participant-generated grids. In addition, a description of each participating team’s software and methods is included.

Pawel Chwalowski↗

Suppression of quantum decoherence via infrared-driven coherent exciton-plasmon coupling: Undamped field and Rabi oscillations

We show that when a semiconductor quantum dot is in the vicinity of a metallic nanoparticle and driven by a mid-infrared laser field, its coherent dynamics caused by interaction with a visible laser field can become free of quantum decoherence. We demonstrate that this process, which can offer undamped Rabi and field oscillations, is the result of coherent normalization of the “effective” polarization dephasing time of the quantum dot (T{sub 2}{sup *}). This process indicates formation of infrared-induced coherently forced oscillations, which allows us to control the value of T{sub 2}{sup *} using the infrared laser. The results offer decay-free ultrafast modulation of the effective field experienced by the quantum dot when neither the visible laser field nor the infrared laser changes with time.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Field Characteristics of Spin-Torque Diode Sensitivity in the Presence of a Bias Current

The use of the spin-torque diode effect, which is generated upon the current-induced transfer of spin angular momentum in magnetic tunnel junctions, opens the prospect of considerably improving microwave sensitivity in the gigahertz frequency band over that of semiconductor Schottky diodes. In this work, the spin-diode effect of microwave signal rectification in a magnetic tunnel junction upon the resonant excitation of spin waves in the free magnetic layer as a result of the current-induced spin-transfer torque effect is analyzed theoretically. Frequency characteristics of the resonant response of a spin-torque diode to a microwave signal are calculated in the linear macrospin approximation as functions of the direction and value of the applied magnetic field and bias current. It is shown that with zero bias current, the maximum rectified voltage across a junction is obtained in the geometry of mutually perpendicular magnetizations of magnetic layers; as the resonant frequency of oscillations in a magnetic field increases, this voltage drops at the retained equilibrium orientation of spins in the layers. After the bias current is switched on, the resonance amplitude of forced oscillations of the free layer spins upon microwave excitation grows sharply at the critical point of the spin-torque diode’s loss of equilibrium state stability. The linewidth at this point is limited only by nonlinear effects. Improving spin-torque diode sensitivity is important for its use in microwave holographic vision systems.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Preliminary Measurement of Pitch Damping of Blunt Entry Vehicles in a Subsonic Magnetic Suspension Wind Tunnel

Blunt bodies have been magnetically suspended in a 6-inch octagonal test-section low-subsonic wind tunnel in a free-to oscillate configuration. Capsule oscillations of two entry vehicle geometries were measured from high speed video of repeated test runs. An analytical solution to the 1degree-of-freedom equations of motion was fit to the measured oscillation histories to solve for a pitch damping coefficient. A six degree-of-freedom simulation was used to predict the wind tunnel data and assess the effect of magnetic forces on capsule dynamics. The predicted effect was used in the data reduction methodology to improved the pitch damping measurement. Pitch damping measurements are compared with heritage forced oscillation data and are in good agreement. Preliminary uncertainties are included with recommendations for improved data reduction.

Dynamic Stability↗

Estimation of Longitudinal Unsteady Aerodynamics of a Wing-Tail Combination From Wind Tunnel Data

This paper presents an initial step toward model identification from wind tunnel data for an airliner configuration. Two approaches to modeling a transport configuration are considered and applied to both steady and large-amplitude forced-oscillation wind tunnel data taken over a wide range of angles of attack. Only limited conclusions could be drawn from this initial data set. Although model estimated time histories of normal force and pitching moment agree reasonably well with the corresponding measured values, model damping parameters did not, for some cases, have values consistent with small amplitude oscillatory data. In addition, large parameter standard errors implied poor information content for model structure determination and parameter estimation. Further investigation of the modeling problem for more general aerodynamic models is recommended with close attention to experiment design for obtaining parameters with high accuracy.

Murphy, Patrick C.↗

Coordinated Polar Spacecraft, Geosynchronous Spacecraft, and Ground-based Observations of Magnetopause Oscillations and Pc5 Waves in the Magnetosphere

In this paper, we present in situ observations of surface waves at the magnetopause and oscillatory magnetospheric field lines, and coordinated observations Pc5 waves at geosynchronous orbit by the GOES spacecraft, and on the ground by CANOPUS and 210 Degree Magnetic Meridian (210MMJ magnetometer arrays. On February 7,2002 during a highspeed solar wind stream, the Polar spacecraft was skimming the magnetopause in a post-noon meridian plane for approximately 3 hours. During this interval, it made two short excursions and a few partial crossings into the magnetosheath and observed quasi-periodic cold ion bursts in the region adjacent to the magnetopause current layer. The multiple magnetopause crossings as well as the velocity of the cold ion bursts indicate that the magnetopause was oscillating with about 6 minute period. Simultaneous observations of Pc5 waves at geosynchronous orbit by the GOES spacecraft and on the ground by the CANOPUS magnetometer array reveal that these magnetospheric pulsations were forced oscillations of magnetic field lines directly driven by the magnetopause oscillations. The magnetospheric pulsations occurred only in a limited longitudinal region in the post-noon dayside sector, and were not a global phenomenon as one would expect for global field line resonance. Thus, the magnetopause oscillations at the source were also limited to a localized region spanning about 4 hours in local time.

Le, G.↗

Improvement of force factor of magnetostrictive vibration power generator for high efficiency

We develop high power magnetostrictive vibration power generator for battery-free wireless electronics. The generator is based on a cantilever of parallel beam structure consisting of coil-wound Galfenol and stainless plates with permanent magnet for bias. Oscillating force exerted on the tip bends the cantilever in vibration yields stress variation of Galfenol plate, which causes flux variation and generates voltage on coil due to the law of induction. This generator has advantages over conventional, such as piezoelectric or moving magnet types, in the point of high efficiency, highly robust, and low electrical impedance. Our concern is the improvement of energy conversion efficiency dependent on the dimension. Especially, force factor, the conversion ratio of the electromotive force (voltage) on the tip velocity in vibration, has an important role in energy conversion process. First, the theoretical value of the force factor is formulated and then the validity was verified by experiments, where we compare four types of prototype with parameters of the dimension using 7.0 × 1.5 × 50 mm beams of Galfenol with 1606-turn wound coil. In addition, the energy conversion efficiency of the prototypes depending on load resistance was measured. The most efficient prototype exhibits the maximum instantaneous power of 0.73 W and energy of 4.7 mJ at a free vibration of frequency of 202 Hz in the case of applied force is 25 N. Further, it was found that energy conversion efficiency depends not only on the force factor but also on the damping (mechanical loss) of the vibration.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Test Cases for the Benchmark Active Controls: Spoiler and Control Surface Oscillations and Flutter

As a portion of the Benchmark Models Program at NASA Langley, a simple generic model was developed for active controls research and was called BACT for Benchmark Active Controls Technology model. This model was based on the previously-tested Benchmark Models rectangular wing with the NACA 0012 airfoil section that was mounted on the Pitch and Plunge Apparatus (PAPA) for flutter testing. The BACT model had an upper surface spoiler, a lower surface spoiler, and a trailing edge control surface for use in flutter suppression and dynamic response excitation. Previous experience with flutter suppression indicated a need for measured control surface aerodynamics for accurate control law design. Three different types of flutter instability boundaries had also been determined for the NACA 0012/PAPA model, a classical flutter boundary, a transonic stall flutter boundary at angle of attack, and a plunge instability near M = 0.9. Therefore an extensive set of steady and control surface oscillation data was generated spanning the range of the three types of instabilities. This information was subsequently used to design control laws to suppress each flutter instability. There have been three tests of the BACT model. The objective of the first test, TDT Test 485, was to generate a data set of steady and unsteady control surface effectiveness data, and to determine the open loop dynamic characteristics of the control systems including the actuators. Unsteady pressures, loads, and transfer functions were measured. The other two tests, TDT Test 502 and TDT Test 5 18, were primarily oriented towards active controls research, but some data supplementary to the first test were obtained. Dynamic response of the flexible system to control surface excitation and open loop flutter characteristics were determined during Test 502. Loads were not measured during the last two tests. During these tests, a database of over 3000 data sets was obtained. A reasonably extensive subset of the data sets from the first two tests have been chosen for Test Cases for computational comparisons concentrating on static conditions and cases with harmonically oscillating control surfaces. Several flutter Test Cases from both tests have also been included. Some aerodynamic comparisons with the BACT data have been made using computational fluid dynamics codes at the Navier-Stokes level (and in the accompanying chapter SC). Some mechanical and active control studies have been presented. In this report several Test Cases are selected to illustrate trends for a variety of different conditions with emphasis on transonic flow effects. Cases for static angles of attack, static trailing-edge and upper-surface spoiler deflections are included for a range of conditions near those for the oscillation cases. Cases for trailing-edge control and upper-surface spoiler oscillations for a range of Mach numbers, angle of attack, and static control deflections are included. Cases for all three types of flutter instability are selected. In addition some cases are included for dynamic response measurements during forced oscillations of the controls on the flexible mount. An overview of the model and tests is given, and the standard formulary for these data is listed. Some sample data and sample results of calculations are presented. Only the static pressures and the first harmonic real and imaginary parts of the pressures are included in the data for the Test Cases, but digitized time histories have been archived. The data for the Test Cases are also available as separate electronic files.

Bennett, Robert M.↗

The measured and estimated rotary stability derivatives of the X-15 airplane

Measurements of the rotary derivatives of the X-15 aircraft were made in several of the wind tunnels of the National Advisory Committee for Aeronautics. The speed range was from landing speed up to Mach number, 3.5. The measurements were made on the steady-state, forced-oscillation equipment. The apparatus measures the rotary derivatives during small-amplitude, single-degree-of-freedom oscillations. In this paper the results of the wind-tunnel tests are compared with the values of the rotary derivatives estimated by the available procedures. Whenever possible, the results of wind-tunnel measurements of the static forces and moments on the X-15 have been utilized in the estimation procedures to obtain lift-curve slopes and centers of pressure of the tail surfaces. In this way, at least a partial account is taken of the effects of the fuselage and wing downwash and pressure field on the tail surfaces.

Tinling, Bruce↗

Dual-scale folding in cutting of commercially pure aluminum alloys

We examine a, hitherto, little-studied and curious machining chip morphology, with tell-tale signs of folding at two different length scales, that is common in cutting of certain ductile and highly strain-hardening metals like soft aluminum alloys, tantalum and niobium. This chip morphology does not appear in the usual catalogues of common chip types. The mechanics of formation of the “dual-scale folded chip” is studied in model material systems of commercially pure aluminum alloys (AA 1100 and AA 8040), that prominently exhibit this chip morphology. The flow, folding and associated plastic instabilities are investigated using micro/macro structure observations of the chip in a plane-strain cutting framework, with high-speed in situ imaging and image analysis of material flow; and force measurements. The smaller-scale folding is shown to develop in the primary deformation zone while the larger-scale folding occurs as the chip traverses the rake face of the tool. The resulting chip is composed of irregularly-spaced large folds, superimposed onto which are the quasi periodic small folds. The representative wavelengths of the two folds differ on average by an order of magnitude, 0.1 mm vs. 2 mm. The observations reveal a direct coupling between the material flow and chip morphology, and how specific attributes of the dual-scale folded chip arise from the flow mechanism. Plastic buckling is found to play a key role in the folding at both length scales. The small-scale folds are characteristic of a sinuous plastic flow mode, while the large-scale folding is characterized by buckling and stick-slip along the tool rake face, triggered by adhesive pinning of the chip to the tool. Important consequences of the dualscale folding are very large cutting forces, and force oscillations of large amplitude, despite the alloys being very soft, only ~ 25 HV. Here, the dual-scale folding is why many of these alloys are classified as “gummy” to machine. Since the dual-scale folded chip is associated with large cutting forces and poor surface quality, there is much to be gained by disrupting this flow type in practical machining applications. Methods for controlling the folding to improve machining performance with the gummy alloys are briefly discussed.

36 MATERIALS SCIENCE↗