Search NASA⌕ Search

SEARCH · Search NASA

Results for “Frequency estimation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

High-dynamic GPS tracking

The results of comparing four different frequency estimation schemes in the presence of high dynamics and low carrier-to-noise ratios are given. The comparison is based on measured data from a hardware demonstration. The tested algorithms include a digital phase-locked loop, a cross-product automatic frequency tracking loop, and extended Kalman filter, and finally, a fast Fourier transformation-aided cross-product frequency tracking loop. The tracking algorithms are compared on their frequency error performance and their ability to maintain lock during severe maneuvers at various carrier-to-noise ratios. The measured results are shown to agree with simulation results carried out and reported previously.

Hinedi, S.↗

Friction Velocity Estimation Using Dual-Frequency Altimeter Data

Global estimation of wind speeds near the sea-surface can be obtained using normalized radar cross sections sigma(o) from satellite-borne single-frequency altimeters. Indeed recent validation studies of Geosat altimeter-derived wind speeds show that several often cited semiempirical algorithms yield linear trends between wind-speeds from altimeter data and wind speeds from (a) ships of opportunity (Etcheto 1992), (b) buoys (Carter 1992), and (c) atmospheric models (Guillaume 1992). Although the linear trends are striking, there is considerable scatter since the range of standard deviations is from 1.5 to 3 m/s. In fact, the scatter of some particular measurements about the regressions is striking because they depart from the 'standard' by as much as +/- 5 m/s, which is large - even for full gale winds of 20 m/s. These anomalies can cause serious problems for gas exchange, heat, and aerosol estimates. They can also induce considerable errors in wind-driven oceanic circulation models and sea-surface wave models. This paper explores the possibility of improving the accuracy of wind speed estimation using dual-frequency altimeters.

Bliven, Larry F.↗

Efficient detection and signal parameter estimation with applications to high dynamic GPS receivers

A novel technique for simultaneously detecting data and estimating the parameters of a received carrier signal phase modulated by unknown data and experiencing very high Doppler, Doppler rate, etc. is discussed. Such a situation arises, for example, in the case of Global Positioning Systems (DPS) where the signal parameters are directly related to the position, velocity and acceleration of the GPS receiver. The proposed scheme is based upon first estimating the received signal local (data dependent) parameters over two consecutive bit periods, followed by the detection of a possible jump in these parameters. The presence of a detected jump signifies a data transition which is then removed from the received signal. This effectively demodulated signal is then processed to provide the estimates of global (data independent) parameters of the signal related to the position, velocity, etc. of the receiver. One of the key features of the proposed algorithm is the introduction of two different schemes which can provide an improvement of up to 3 dB over the conventional implementation of Kalman filter as applied to phase and frequency estimation, under low to medium signal-to-noise ratio conditions.

Kumar, R.↗

Real-Time Detection and Localization of Line Trip Event Via Relative Phase Angles

Line trip events widely exist in power systems. They can result in power outages and a huge economic loss if not promptly detected and localized. To provide a fast and precise solution, this paper presents a Complete Coverage of Voltage Measurement (CCVM)-based line trip event detection algorithm and a Relative Phase Angle (RPA)-based line trip event localization algorithm. First, frequency and relative phase angle features during a line trip event are calculated. Then, the CCVM-based algorithm is proposed from both frequency and rate of change of frequency estimation algorithm aspects. Additionally, the RPA-based algorithm is presented, and two cases are studied to demonstrate the uniqueness of the proposed algorithm. Various experiments are conducted, where the simulation results demonstrate that the proposed CCVM-based algorithm can detect a line trip event as short as 2.07 ms. In addition, the RPA-based algorithm has 1.26 times higher localization accuracy compared with the frequency magnitude-based and phase angle-based algorithms. In conclusion, the experiment results on the examples from two interconnected power systems in the U.S. verified the performance of the proposed algorithms in wide-area power systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Detection of Periodic Forced Oscillations in Power Systems

An algorithm for the detection and frequency estimation of forced oscillations in power systems is proposed. The method operates by comparing the periodogram of synchrophasor measurements to a detection threshold. This threshold is established by deriving a general expression for the distribution of the periodogram and is related to the algorithm's probabilities of false alarm and detection. Unlike classic detection algorithms designed for use with white Gaussian noise, the proposed algorithm uses a detection threshold that varies with frequency to account for the colored nature of synchrophasor measurements. Further, a detection scheme based on multiple segments of data is proposed to improve the algorithm's performance as a monitoring tool in the online environment. A design approach that helps to ensure that the best-available probability of detection from any one detection segment is constantly increasing with the duration of the forced oscillation is also developed. Results from application of the detection algorithm to simulated and measured power system data suggest that the algorithm provides the expected detection performance and can be used to detect forced oscillations in practical monitoring of power systems.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Synchronized Wireless Measurement of High-Voltage Power System Frequency Using Mobile Embedded Systems

This paper focuses on synchronized wireless measurement of high-voltage (HV) power system frequency using mobile embedded systems (MESs) integrated with a wireless electric field sensor (WEFS). Unlike traditional synchronized frequency measurement devices, which rely on potential transformers and current transformers physically connected to system elements, a WEFS is used to realize wireless signal acquisition in the vicinity of any HV apparatus. The MES performs real-time frequency estimation using a recursive discrete Fourier transform based algorithm. Network time protocol (NTP) is used for time synchronization, increasing the system flexibility by eliminating global positioning system reliance. An NTP-based synchronized sampling control method is proposed and implemented in MES to compensate the sampling time error caused by local time drift and division residue. The proposed system has the advantages of portability and lower cost, making it highly accessible and useful for a wide array of synchronized frequency measurement applications. Experiment results verify the accuracy and effectiveness of the proposed system.

24 POWER TRANSMISSION AND DISTRIBUTION↗

On the detectability of strong lensing in near-infrared surveys

We present new lensing frequency estimates for existing and forthcoming deep near-infrared surveys, including those from JWST and VISTA. The estimates are based on the JAdes extragalactic Ultradeep Artificial Realisations (JAGUAR) galaxy catalogue accounting for the full photometry and morphologies for each galaxy. Due to the limited area of the JAGUAR simulations, they are less suited to wide-area surveys; however, we also present extrapolations to the surveys carried out by Euclid and the Nancy Grace Roman Space Telescope. The methodology does not make assumptions about the nature of the lens itself and probes a wide range of lens masses. The lenses and sources are selected from the same catalogue and extend the analysis from the visible bands into the near-infrared. After generating realistic simulated lensed sources and selecting those that are detectable with SNR > 20, we verify the lensing frequency expectations against published lens samples selected in the visible, finding them to be broadly consistent. We find that JWST could yield ~65 lensed systems in COSMOS-Web, of which ~25 per cent have source redshifts >4. Deeper, narrower programs (e.g. JADES-Medium) will probe more typical source galaxies (in flux and mass) but will find fewer systems (~25). Of the surveys we investigate, we find 55–80 per cent have detectable multiple imaging. Forthcoming NIR surveys will likely reveal new and diverse strong lens systems including lensed sources that are at higher redshift (JWST) and dustier, more massive and older (Euclid NISP) than those typically detected in the corresponding visible surveys.

79 ASTRONOMY AND ASTROPHYSICS↗

Reconciling Ground-Based and Space-Based Estimates of the Frequency of Occurrence and Radiative Effect of Clouds around Darwin, Australia

The objective of this paper is to investigate whether estimates of the cloud frequency of occurrence and associated cloud radiative forcing as derived from ground-based and satellite active remote sensing and radiative transfer calculations can be reconciled over a well instrumented active remote sensing site located in Darwin, Australia, despite the very different viewing geometry and instrument characteristics. It is found that the ground-based radar-lidar combination at Darwin does not detect most of the cirrus clouds above 10 km (due to limited lidar detection capability and signal obscuration by low-level clouds) and that the CloudSat radar - Cloud-Aerosol Lidar with Orthogonal Polarization (CALIOP) combination underreports the hydrometeor frequency of occurrence below 2 km height, due to instrument limitations at these heights. The radiative impact associated with these differences in cloud frequency of occurrence is large on the surface downwelling shortwave fluxes (ground and satellite) and the top-of atmosphere upwelling shortwave and longwave fluxes (ground). Good agreement is found for other radiative fluxes. Large differences in radiative heating rate as derived from ground and satellite radar-lidar instruments and RT calculations are also found above 10 km (up to 0.35 Kday-1 for the shortwave and 0.8 Kday-1 for the longwave). Given that the ground-based and satellite estimates of cloud frequency of occurrence and radiative impact cannot be fully reconciled over Darwin, caution should be exercised when evaluating the representation of clouds and cloud-radiation interactions in large-scale models and limitations of each set of instrumentation should be considered when interpreting model-observations differences.

clouds↗

NSLS-II: Nonlinear Model Calibration for Synchrotrons

This tech note is essentially a summary of a lecture we delivered to the Acc. Phys. Journal Club Apr, 2010. However, since the estimated accuracy of these methods has been naive and misleading in the field of particle accelerators, i.e., ignores the impact of noise, we will elaborate on this in some detail. A prerequisite for a calibration of the nonlinear Hamiltonian is that the quadratic part has been understood, i.e., that the linear optics for the real accelerator has been calibrated. For synchrotron light source operations, this problem has been solved by the interactive LOCO technique/tool (Linear Optics from Closed Orbits). Before that, in the context of hadron accelerators, it has been done by signal processing of turn-by-turn BPM data. We have outlined how to make a basic calibration of the nonlinear model for synchrotrons. In particular, we have shown how this was done for LEAR, CERN (antiprotons) in the mid-80s. Specifically, our accuracy for frequency estimation was {approx} 1 x 10{sup -5} for 1024 turns (to calibrate the linear optics) and {approx} 1 x 10{sup -4} for 256 turns for tune footprint and betatron spectrum. For a comparison, the estimated tune footprint for stable beam for NSLS-II is {approx}0.1. Since the transverse damping time is {approx}20 msec, i.e., {approx}4,000 turns. There is no fundamental difference for: antiprotons, protons, and electrons in this case. Because the estimated accuracy for these methods in the field of particle accelerators has been naive, i.e., ignoring the impact of noise, we have also derived explicit formula, from first principles, for a quantitative statement. For e.g. N = 256 and 5% noise we obtain {delta}{nu} {approx} 1 x 10{sup -5}. A comparison with the state-of-the-arts in e.g. telecomm and electrical engineering since the 60s is quite revealing. For example, Kalman filter (1960), crucial for the: Ranger, Mariner, and Apollo (including the Lunar Module) missions during the 60s. Or Claude Shannon et al since the 40s for that matter. Conclusion: what's elementary in the latter is considered 'advanced', if at all, in the former. It is little surprise then that published measurements typically contains neither error bars (for the random errors) nor estimates for the systematic in the former discipline. We have also showed how to estimate the state space by turn-by-turn data from two adjacent BPMs. And how to improve the resolution of the nonlinear resonance spectrum by Fourier analyzing the linear action variables instead of the betatron motion. In fact, the state estimator could be further improved by adding a Kalman filter. For transparency, we have also summarized on how these techniques provide a framework- and method for a TQM (Total Quality Management) approach for the main ring. Of course, to make the ($2.5M) turn-by-turn data acquisition system that is being implemented (for all the BPMs) useful, a means ({approx}10% contingency for the BPM system) to drive the beam is obviously required.

43 PARTICLE ACCELERATORS↗

Estimation of pipe failure frequencies in the absence of operational experience data: A pilot study

Probabilistic failure metrics such as leak frequency and rupture frequency are commonly used to characterize piping reliability. The methodologies for calculating the failure metrics rely on a complex set of input parameters. Operating experience data and experimental data play an important role in informing the different input parameters. The paper describes results and conclusions of a coordinated research project to benchmark three different reliability models using a four-step procedure: reference case definition of relevance to advanced reactor designs, input parameter calibration, validation of results, and application of different methodologies upon completion of the calibration and validation steps. The reference case is a weld consisting of nickel-base alloy 152/52 and located within a primary pressure boundary of an advanced reactor. This alloy is a class of structural materials known to be highly resistant to stress corrosion cracking. Synergies between the different methods are noted and the importance of a multi-disciplinary approach to input parameter development is underscored. A key conclusion is that the three methods are equally suitable for estimating failure frequencies. In any specific application, a selection of the most practical or effective computational tool can be considered. The comparison of alternative models confirms and helps to gain confidence in the computed failure frequency estimates. The study was part of a coordinated research project organized by the International Atomic Energy Agency.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

The Transmission of ULF Waves From the Solar Wind to the Magnetosphere: An Analysis of Some Critical Aspects

Several critical aspects may influence the analysis of the relationship between the solar wind (SW) and magnetospheric fluctuations, for example, the characteristics and frequency of SW fluctuations that are expected to impinge the magnetosphere may not be the same when they are observed by spacecraft located at different places in front of the magnetosphere; similarly, the choice of analytical methods adopted for the spectral analysis might influence the frequency estimate (as well as the wave identification itself) both in the SW and magnetosphere. Focusing our attention on these aspects, we present an analysis of SW compressional fluctuations (f ≈ 1–5 mHz), following two interplanetary shocks observed by two interplanetary spacecraft, regarded as two different situations in terms of spacecraft separation and distance from the magnetosphere. Our results show that some differences in the characteristics of SW fluctuations emerge when the same stream is observed at different places and confirm the critical role of analytical methods in determining fluctuation characteristics. We compared aspects of SW fluctuations with those of magnetospheric fluctuations following the sudden impulses due to the impact of interplanetary shocks. For this scope, we examined observations by two satellites at geostationary orbit and at several ground-based stations. We found that the magnetospheric fluctuations were related to compressional SW fluctuations approximately at the same frequencies, with no evidence for wave activity of internal origin or directly driven by the shock impact.

ULF waves↗

Assessment and Control of Spacecraft Charging Risks on the International Space Station

Electrical interactions between the F2 region ionospheric plasma and the 160V photovoltaic (PV) electrical power system on the International Space Station (ISS) can produce floating potentials (FP) on the ISS conducting structure of greater magnitude than are usually observed on spacecraft in low-Earth orbit. Flight through the geomagnetic field also causes magnetic induction charging of ISS conducting structure. Charging processes resulting from interaction of ISS with auroral electrons may also contribute to charging albeit rarely. The magnitude and frequency of occurrence of possibly hazardous charging events depends on the ISS assembly stage (six more 160V PV arrays will be added to ISS), ISS flight configuration, ISS position (latitude and longitude), and the natural variability in the ionospheric flight environment. At present, ISS is equipped with two plasma contactors designed to control ISS FP to within 40 volts of the ambient F2 plasma. The negative-polarity grounding scheme utilized in the ISS 160V power system leads, naturally, to negative values of ISS FP. A negative ISS structural FP leads to application of electrostatic fields across the dielectrics that separate conducting structure from the ambient F2 plasma, thereby enabling dielectric breakdown and arcing. Degradation of some thermal control coatings and noise in electrical systems can result. Continued review and evaluation of the putative charging hazards, as required by the ISS Program Office, revealed that ISS charging could produce a risk of electric shock to the ISS crew during extra vehicular activity. ISS charging risks are being evaluated in ongoing ISS charging measurements and analysis campaigns. The results of ISS charging measurements are combined with a recently developed detailed model of the ISS charging process and an extensive analysis of historical ionospheric variability data, to assess ISS charging risks using Probabilistic Risk Assessment (PRA) methods. The PRA analysis (estimated frequency of occurrence and severity of the charging hazards) are then used to select the hazard control strategy that provides the best overall safety and mission success environment for ISS and the ISS crew. This paper presents: 1) a summary of ISS spacecraft charging analysis, measurements, observations made to date, 2) plans for future ISS spacecraft charging measurement campaigns, and 3) a detailed discussion of the PRA strategy used to assess ISS spacecraft charging risks and select charging hazard control strategies

Koontz, Steve↗

Stochastic Simulation of Daily Suspended Sediment Concentration Using Multivariate Copulas

Estimation of daily suspended sediment concentration (SSC) is required for water resources and environment management. In this paper, a copula-based stochastic method was proposed for daily SSC simulation. Here, the multivariate copula function, constructed based on a bivariate copula and two bivariate conditional probability distributions, was used to model the temporal and cross dependence structures in daily SSCs. Then, the daily SSCs were generated by sampling from the multivariate conditional distribution. As a result, synthetic long-term SSCs data beyond the limited observation period can be provided for water resources managers, which plays a critical role in accurately estimating frequency and magnitude of extreme SSCs events. The proposed method was under rigorous examination by applying to a case study at Pingshan station in the Jinsha River Basin, China. Results showed that the generated daily SSC sequences not only had a high degree of accuracy in preserving the statistical characteristics of the daily SSC observations, but also captured both the temporal correlation and the cross-correlation between the daily streamflow and daily SSC. Specifically, the average daily relative error values corresponding to mean, standard deviation, skewness, lag-1 temporal correlation, and cross correlation were 0.87%, 4.24%, 7.52%, 0.51% and 2.02%, respectively. The multivariate copula framework proposed here can accurately and efficiently generate long-term daily SSC data for water resources management such as frequency analysis and risk assessment of extreme SSC events.

54 ENVIRONMENTAL SCIENCES↗

A workflow for automatic generation and efficient refinement of individual pressure-dependent networks

Manual chemical kinetic model construction often requires modelists to at least implicitly guess all possible decay pathways and their relative fluxes for all important species. We present a workflow and associated tool for automatic generation and re finement of pressure-dependent networks that should enable modelists to efficiently and comprehensively identify decay pathways and estimate respective parameters for chemical species. This tool combines the capabilities of the Reaction Mechanism Generator (RMG) software to generate possible reaction paths, determine thermochemistry, approximate rate coefficients and estimate frequencies with the capabilities of the Arkane software to use quantum chemical parameters to compute thermochemistry and pressure dependent rates. A flux-based algorithm is used to decide which isomers to add to the network. Isomers added to the network are reacted to form other channels. When enough of the flux is accounted for by the isomers and bimolecular product channels, the generation process terminates to yield a comprehensive network. Network sensitivity analysis is applied to the network to identify the most important wells and barriers that can be refined using quantum chemistry calculations. Iterative refinement can then be used to achieve accuracy. The comprehensive network can be easily reduced using energy and flux-based algorithms to the most important channels and isomers in the network.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Fault-tolerant grid frequency measurement algorithm during transients

Many critical electric grid operations rely on accurate grid frequency measurements. Unfortunately, the measurement accuracy can be easily undermined by power system transient faults. During a power system transient fault, the power grid voltages and currents are usually highly distorted by high-frequency components. What is worse, the power grid signals could have discontinuity during some system transient faults such as phase angle jump, and the discontinuity could result in large measurement errors to state-of-the-art grid measurement algorithms. In this study, a fault-tolerant grid frequency measurement algorithm during transients is proposed. The new algorithm consists of two stages. The first stage is a transient detector, and it can detect the occurrence of system transient faults instantaneously. The second stage is the intelligent frequency estimator, and it will adapt its measurements according to the transient detector. The performance of the algorithm is evaluated under different steady-state and transient conditions. Both dependability and security of the fault-tolerant algorithm are assessed by using PSCAD simulation data and IEEE Standard test data.

24 POWER TRANSMISSION AND DISTRIBUTION↗

Communicating the Impacts of Projected Climate Change on Heavy Rainfall Using a Weighted Ensemble Approach

Urban flood risks are often determined by the frequency analysis of observed rainfall data, communicated using isohyetal maps showing rainfall totals for a range of durations and recurrence intervals. However, to assess future changes in heavy rainfall, it is necessary to study the future projected rainfall time series. Impacts of climate change are typically assessed using climate projections based on global climate model (GCM) outputs and downscaled to finer temporal and spatial scales. The projected data, however, are not generated in a format that urban planners and engineers can easily use to design for future conditions. This paper presents a method to analyze and express climate data in a format that can be readily used in hydrologic models to assess the effects of future extreme rainfall events. Future conditions’ climate data were analyzed using a weighted ensemble approach, which resulted in projected rainfall frequency estimates and their confidence limits. Two multimodel data sets were selected to illustrate this approach in Cook County, Illinois, which belongs to the Chicago metropolitan area. The first data set included statistical downscaling data based on the Intergovernmental Panel for Climate Change’s (IPCC) Coupled Model Intercomparison Project Phase 3 (CMIP3) data. The weighted ensemble analysis applied to this data set produced results that indicated significant increases in projected heavy rainfall. For example, for CMIP3 Scenario A2, for the late 21st century, the 100-year, 24-h rainfall in the northern parts of the county was 29% larger than the model-generated rainfall for the present time. Finally, for the same time horizon and scenario, the confidence interval based on projected data was 87% wider compared with that of the published source (NOAA Atlas 14), calculated using the past observed data. Also, equal-weight delta-corrected IPCC CMIP5-based dynamical downscaling data were applied to the same region for the mid-21st century, producing increases in heavy rainfall fairly similar to those of CMIP3.

54 ENVIRONMENTAL SCIENCES↗

Circuit model of the ITER-like antenna for JET and simulation of its control algorithms

The ITER-like Antenna (ILA) for JET [1] is a 2 toroidal by 2 poloidal array of Resonant Double Loops (RDL) featuring in-vessel matching capacitors feeding RF current straps in conjugate-T manner, a low impedance quarter-wave impedance transformer, a service stub allowing hydraulic actuator and water cooling services to reach the aforementioned capacitors and a 2nd stage phase-shifter-stub matching circuit allowing to correct/choose the conjugate-T working impedance. Toroidally adjacent RDLs are fed from a 3dB hybrid splitter. It has been operated at 33, 42 and 47MHz on plasma (2008-2009) while it presently estimated frequency range is from 29 to 49MHz. At the time of the design (2001-2004) as well as the experiments the circuit models of the ILA were quite basic. The ILA front face and strap array Topica model was relatively crude and failed to correctly represent the poloidal central septum, Faraday Screen attachment as well as the segmented antenna central septum limiter. The ILA matching capacitors, T-junction, Vacuum Transmission Line (VTL) and Service Stubs were represented by lumped circuit elements and simple transmission line models. The assessment of the ILA results carried out to decide on the repair of the ILA identified that achieving routine full array operation requires a better understanding of the RF circuit, a feedback control algorithm for the 2nd stage matching as well as tighter calibrations of RF measurements. The paper presents the progress in modelling of the ILA comprising a more detailed Topica model of the front face for various plasma Scrape Off Layer profiles, a comprehensive HFSS model of the matching capacitors including internal bellows and electrode cylinders, 3D-EM models of the VTL including vacuum ceramic window, Service stub, a transmission line model of the 2nd stage matching circuit and main transmission lines including the 3dB hybrid splitters. A time evolving simulation using the improved circuit model allowed to design and simulate the effectiveness of a feedback control algorithm for the 2nd stage matching and demonstrates the simultaneous matching and control of the 4 RDLs: 11 feedback loops control 21 actuators (8 capacitors, 4 phase shifters and 4 stubs for the 2nd stage matching, 4 main phase shifters controlling of the toroidal phasing and the electronically controlled phase between RF sources feeding top and bottom parts of the array and determines the poloidal phasing of the array which is solved explicitly at each time step) on (simulated) ELMy plasmas.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

INTERACTING GALAXIES IN THE A901/902 SUPERCLUSTER WITH STAGES

We present a study of galaxy mergers and the influence of environment in the Abell 901/902 supercluster at zapprox 0.165, based on 893 bright (R{sub Vega}<= 24) intermediate-mass (M{sub *} >= 10{sup 9} M{sub sun}) galaxies. We use HST ACS F606W data from the Space Telescope A901/902 Galaxy Evolution Survey, COMBO-17, Spitzer 24 mum, and XMM-Newton X-ray data. Our analysis utilizes both a physically driven visual classification system and quantitative CAS parameters to identify systems which show evidence of a recent or ongoing merger of mass ratio >1/10 (i.e., major and minor mergers). Our results are (1) after visual classification and minimizing the contamination from false projection pairs, we find that the merger fraction f{sub merge} is 0.023 +- 0.007. The estimated fractions of likely major mergers, likely minor mergers, and ambiguous cases are 0.01 +- 0.004, 0.006 +- 0.003, and 0.007 +- 0.003, respectively. (2) All the mergers lie outside the cluster core of radius R< 0.25 Mpc: the lack of mergers in the core is likely due to the large galaxy velocity dispersion in the core. The mergers, instead, populate the region (0.25 Mpc <R<= 2 Mpc) between the core and the cluster outskirt. In this region, the estimated frequency of mergers is similar to those seen at typical group overdensities in N-body simulations of accreting groups in the A901/902 clusters. This suggests the ongoing growth of the clusters via accretion of group and field galaxies. (3) We compare our observed merger fraction with those reported in other clusters and groups out to zapprox 0.4. Existing data points on the merger fraction for L <= L* galaxies in clusters allow for a wide spectrum of scenarios, ranging from no evolution to evolution by a factor of approx5 over zapprox 0.17-0.4. (4) In A901/902, the fraction of interacting galaxies, which lie on the blue cloud is 80% +- 18% (16/20) versus 34% +- 7% or (294/866) for non-interacting galaxies, implying that interacting galaxies are preferentially blue. (5) The average star formation rate (SFR), based on UV or a combination of UV+IR data, is enhanced by a factor of approx1.5-2 in mergers compared to non-interacting galaxies. However, mergers in the A901/902 clusters contribute only a small fraction (between 10% and 15%) of the total SFR density, while the rest of the SFR density comes from non-interacting galaxies.

79 ASTRONOMY AND ASTROPHYSICS↗