Search NASA⌕ Search

SEARCH · Search NASA

Results for “GAS HEATING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Thermal-Flow Code for Modeling Gas Dynamics and Heat Transfer in Space Shuttle Solid Rocket Motor Joints

A new, thermal-flow simulation code, called SFLOW. has been developed to model the gas dynamics, heat transfer, as well as O-ring and flow path erosion inside the space shuttle solid rocket motor joints by combining SINDA/Glo, a commercial thermal analyzer. and SHARPO, a general-purpose CFD code developed at Thiokol Propulsion. SHARP was modified so that friction, heat transfer, mass addition, as well as minor losses in one-dimensional flow can be taken into account. The pressure, temperature and velocity of the combustion gas in the leak paths are calculated in SHARP by solving the time-dependent Navier-Stokes equations while the heat conduction in the solid is modeled by SINDA/G. The two codes are coupled by the heat flux at the solid-gas interface. A few test cases are presented and the results from SFLOW agree very well with the exact solutions or experimental data. These cases include Fanno flow where friction is important, Rayleigh flow where heat transfer between gas and solid is important, flow with mass addition due to the erosion of the solid wall, a transient volume venting process, as well as some transient one-dimensional flows with analytical solutions. In addition, SFLOW is applied to model the RSRM nozzle joint 4 subscale hot-flow tests and the predicted pressures, temperatures (both gas and solid), and O-ring erosions agree well with the experimental data. It was also found that the heat transfer between gas and solid has a major effect on the pressures and temperatures of the fill bottles in the RSRM nozzle joint 4 configuration No. 8 test.

Wang, Qunzhen↗
NASA NTRS2005

Diode Laser Sensors for Arc-Jet Characterization

The development and application of tunable diode laser (TDL) absorption sensors to monitor the health and operating conditions in the large-scale 60 MW arc-heated- plasma wind-tunnel at NASA Ames Research Center is reported. The interactive heating facility (THF) produces re-entry flow conditions by expanding the gas heated in a constricted plasma arc-heater to flow at high velocity over a model located in a test cabin. This facility provides the conditions needed to test thermal protective systems for spacecraft re-entering the earth s atmosphere. TDL sensors are developed to monitor gas flows in both the high-temperature constricted flow and the supersonic expansion flow into test cabin. These sensors utilize wavelength-tuned diode lasers to measure absorption transitions of atomic oxygen near 777.2 nm, atomic nitrogen near 856.8 nm, and atomic copper near 793.3 nm. The oxygen and nitrogen sensors measure the population density in exited electronic states of these atoms. The measurements combined with the assumption of local thermal and chemical equilibrium yield gas temperature (typically near 7,000K). The nitrogen and oxygen population temperatures are redundant, and their close agreement provides an important test of the local thermal equilibrium assumption. These temperature sensors provide time-resolved monitors of the operating conditions of the arc-heater and can be used to verify and control the test conditions. An additional TDL sensor was developed to monitor the copper concentration in the arc-heater flow yielding values as high as 13 ppm. Measurements of copper in the flow can identify flow conditions with unacceptably rapid electrode erosion, and hence this sensor provides valuable information needed to schedule maintenance to avoid costly arc-heater failure. TDL sensors were also developed for measurements in the test cabin, where absorption measurements of the populations of argon and molecular nitrogen in excited metastable electronic states established that the number density of these excited species is much lower than estimated using frozen-chemistry approximations. This key finding suggests that in the post-expansion region there is not a significant energy sequestration in electronically excited species. Finally, TDL measurements of atomic potassium seeded into the test cabin flow were used to directly measure the static temperature of the test gas. The results of this study illustrate the high potential of time-resolved TDL measurements for routine and economical sensing of arc-heater health (gas temperature and electrode erosion) as well as the time-resolved test-cabin-flow conditions in front of the model.

Hanson, Ronald K.↗
NASA NTRS1971

Mathematical analysis of a Vuilleumier refrigerator.

A comprehensive analysis of the Vuilleumier refrigerator was conducted. This analysis includes the effects of nonisothermal gas heat addition and rejection, hot and cold regenerator inefficiencies, conduction losses, and gas leakage losses. A computer program was written which solves the equations resulting from the analysis. The program calculates internal pressures, temperatures, and gas flow rates as functions of refrigerator crank angle, as well as overall refrigerator cooling load and power input. Comparisons between the program results and available data show good agreement, with a marked improvement over the predictions of the ideal model.

Sherman, A.↗
NASA NTRSDate not supplied

Application of Analytical Hierarchy Process for Narrowing Down Nep Candidate Reactor Designs

Nuclear electric propulsion (NEP)-powered vehicles have been contemplated for human Mars missions. The nuclear power system contemplates using a high temperature light-weight nuclear reactor for the production of electrical power in the range of 2-5 MWe with a 3-10 year service life. A myriad of technology options exist for achieving these mission objectives. The analytic hierarchy process (AHP), a multi-attribute decision method, is being used to narrow down the candidate designs. The AHP is a structured decision process that fuses model-supplied quantitative data with subjective assessments to facilitate decisions that involve multiple competing criteria. Proven end-to-end nuclear design and systems analysis tools will be used to provide quantitative performance data such as end-to-end system reliability, system robustness to recover from off-normal conditions, system specific weight (α in kg/kWe), and the ability to meet the service life-time and power level requirements. Three high assay low enriched uranium (HALEU) reactor concepts, namely, gas-, heat pipe- and pumped liquid-cooled nuclear cores coupled to a He/Xe gas or supercritical CO2- Brayton power conversion system are being modeled using the AHP to understand the trade-offs associated with these design combinations. In addition to the reactor and power conversion options, there are a myriad of additional components and subsystems – e.g., radiators, heat exchangers, and recuperators – that also figure into the evaluation process. The choice of the right overall system is a multidimensional problem that has to include not only quantitative data, but also the so called “external factors”, examples of which include the component and subsystem Technology Readiness Levels (TRLs), the associated Advancement Degrees of Difficulty (AD2), the cost and schedule required to achieve a technical maturity consistent with mission infusion, alignment with the priorities of NASA’s Space Nuclear Propulsion program, and alignment with other ongoing government and commercial investments in micro reactors. Focused expert elicitations form the basis for qualitative data set. As a final step, decision-makers individually express their opinions regarding the relative importance of the criteria and preferences among the alternatives through pairwise comparisons. The paper will describe the AHP approach, progress to-date applying it to the NEP human Mars mission problem, and preliminary results. Use of AHP provides sufficient flexibility for incorporating industry input at different stages as the technologies evolve through additional research and development. It is expected that the decision process will be ongoing and expanded to examine additional options and technology choices, culminating in a defensible set of candidate reactor concepts that will form the basis for developing a multi-year NEP technology maturation strategy. .

Dasari V Rao↗
NASA NTRS1991

Large-scale gas dynamical processes affecting the origin and evolution of gaseous galactic halos

Observations of galactic halo gas are consistent with an interpretation in terms of the galactic fountain model in which supernova heated gas in the galactic disk escapes into the halo, radiatively cools and forms clouds which fall back to the disk. The results of a new study of several large-scale gas dynamical effects which are expected to occur in such a model for the origin and evolution of galactic halo gas will be summarized, including the following: (1) nonequilibrium absorption line and emission spectrum diagnostics for radiatively cooling halo gas in our own galaxy, as well the implications of such absorption line diagnostics for the origin of quasar absorption lines in galactic halo clouds of high redshift galaxies; (2) numerical MHD simulations and analytical analysis of large-scale explosions ad superbubbles in the galactic disk and halo; (3) numerical MHD simulations of halo cloud formation by thermal instability, with and without magnetic field; and (4) the effect of the galactic fountain on the galactic dynamo.

Shapiro, Paul R.↗
NASA NTRS1991

Response of a confined gas to volumetric heating in the absence of gravity. I - Slow transients

A one-dimensional model for bulk motion induced by a transient volumetric heat source in a confined gas at zero gravity is considered. Rational approximation methods are used to derive a quantitative theory for the gas response to a spatiallly distributed, time-dependent internal power deposition. The resulting low Mach number compressible flow equations are solved by using perturbation methods. Solutions are given for a conduction-free core and thin conductive boundary layers adjacent to the end walls. It is found that may any spatially nonuniform power deposition will cause fluid motion. Net mass transport in the closed container will occur for certain spatially distributed heating. The model mimics the thermal effects of an exothermic gas phase reaction in vapor transport experiments conducted in space. The solutions demonstrate that thermally induced mass transport can be as large as diffusive mass transport in a typical experiment.

Herczynski, A.↗
NASA NTRS1973

User's manual for the TRW gaspipe 2 program: A vapor-gas front analysis program for heat pipes containing non-condensible gas

A digital computer program for design and analysis of heat pipes which contain non-condensible gases, either for temperature control or to aid in start-up from the frozen state, is presented. Some of the calculations which are possible with the program are: (1) wall temperature profile along a gas-loaded heat pipe, (2) amount of gas loading necessary to obtain desired evaporator temperature at a desired heat load, (3) heat load versus evaporator temperature for a fixed amount of gas in the pipe, and (4) heat and mass transfer along the pipe, including the vapor-gas front region.

Edwards, D. K.↗
NASA NTRS1982

Low NO sub x heavy fuel combustor concept program. Phase 1A: Combustion technology generation coal gas fuels

Combustion tests of two scaled burners using actual coal gas from a 25 ton/day fluidized bed coal gasifier are described. The two combustor configurations studied were a ceramic lined, staged rich/lean burner and an integral, all metal multiannual swirl burner (MASB). The tests were conducted over a range of temperature and pressures representative of current industrial combustion turbine inlet conditions. Tests on the rich lean burner were conducted at three levels of product gas heating values: 104, 197 and 254 btu/scf. Corresponding levels of NOx emissions were 5, 20 and 70 ppmv. Nitrogen was added to the fuel in the form of ammonia, and conversion efficiencies of fuel nitrogen to NOx were on the order of 4 percent to 12 percent, which is somewhat lower than the 14 percent to 18 percent conversion efficiency when src-2 liquid fuel was used. The MASB was tested only on medium btu gas (220 to 270 btu/scf), and produced approximately 80 ppmv NOx at rated engine conditions. Both burners operated similarly on actual coal gas and erbs fuel, and all heating values tested can be successfully burned in current machines.

Sherlock, T. P.↗
NASA NTRS1998

Hybrid IR-Gas Heater for Automated Tow Placement

A hybrid infrared-hot gas heat source has been developed and tested for the NASA Langley Tow Placement Facility. The IR heat source provides supplemental heat to the nip region. The additional heat is intended to reduce the need for conduction heating by the compaction roller, which causes (he roller to stick to the panel surface. Initial bench scale testing was performed to identify the most effective means of focusing IR energy into the nip region. A compact lamp and reflector that placed the lamp as close to the nip point as possible was found to deliver the highest heat flux in the nip region. A prototype heater was installed on the NASA Langley tow placement robot. Panels placed with a 400 C (sticking) compaction roller gave DCB initiation toughness numbers comparable to those reported for autoclave processed panels but were found to have unexpectedly high void contents. Placement with compaction roller temperatures that prevented roller sticking resulted in mode I fracture toughness approximately 70% that reported for autoclave processed panels. The variability in strength among specimens placed with reduced roller temperature was found to be greatly reduced, which implies that use of supplemental nip point heat may improve the robustness of the tow placement process. Use of the IR heat source permitted placement with a compaction roller temperature that would have resulted in negligible interfacial strength with the hot gas torch alone. The roller temperature reductions eliminated the need for the robot operator to attend placement operations.

Grenoble, Ray W.↗
NASA NTRS2011

Fission Surface Power Technology Development Update

Power is a critical consideration in planning exploration of the surfaces of the Moon, Mars, and places beyond. Nuclear power is an important option, especially for locations in the solar system where sunlight is limited or environmental conditions are challenging (e.g., extreme cold, dust storms). NASA and the Department of Energy are maintaining the option for fission surface power for the Moon and Mars by developing and demonstrating technology for a fission surface power system. The Fission Surface Power Systems project has focused on subscale component and subsystem demonstrations to address the feasibility of a low-risk, low-cost approach to space nuclear power for surface missions. Laboratory demonstrations of the liquid metal pump, reactor control drum drive, power conversion, heat rejection, and power management and distribution technologies have validated that the fundamental characteristics and performance of these components and subsystems are consistent with a Fission Surface Power preliminary reference concept. In addition, subscale versions of a non-nuclear reactor simulator, using electric resistance heating in place of the reactor fuel, have been built and operated with liquid metal sodium-potassium and helium/xenon gas heat transfer loops, demonstrating the viability of establishing system-level performance and characteristics of fission surface power technologies without requiring a nuclear reactor. While some component and subsystem testing will continue through 2011 and beyond, the results to date provide sufficient confidence to proceed with system level technology readiness demonstration. To demonstrate the system level readiness of fission surface power in an operationally relevant environment (the primary goal of the Fission Surface Power Systems project), a full scale, 1/4 power Technology Demonstration Unit (TDU) is under development. The TDU will consist of a non-nuclear reactor simulator, a sodium-potassium heat transfer loop, a power conversion unit with electrical controls, and a heat rejection system with a multi-panel radiator assembly. Testing is planned at the Glenn Research Center Vacuum Facility 6 starting in 2012, with vacuum and liquid-nitrogen cold walls to provide simulation of operationally relevant environments. A nominal two-year test campaign is planned including a Phase 1 reactor simulator and power conversion test followed by a Phase 2 integrated system test with radiator panel heat rejection. The testing is expected to demonstrate the readiness and availability of fission surface power as a viable power system option for NASA's exploration needs. In addition to surface power, technology development work within this project is also directly applicable to in-space fission power and propulsion systems.

Palac, Donald T.↗
NASA NTRS1986

Impact erosion of planetary atmospheres

The amount of gas imparted to the atmosphere by an interaction of an impactor with a planet is estimated. The interaction of an impactor with a planet is described. The enthalpy of the gas, the kinetic energy of mass motion, and the evaporation of the impactor are examined. The properties of the shock-heated gas are calculated and analyzed. It is observed that the mass of atmospheric gas driven off into space by an impact is proportional to the mass of atmospheric gas encountered by the impactor.

Walker, James C. G.↗
NASA NTRS1993

The ISM in the M82 starburst

We have observed (O 1) (63 microns) and (Si 2) (35 microns) in the central 700 pc of the starburst galaxy M82. The luminosities in these transitions are 7.1 x 10(exp 7) solar luminosity and 6.2 x 10(exp 7) solar luminosity, respectively, which are each approx. 0.15% of the bolometric luminosity from this region. The ratios of (O 1) line luminosity to (O 3), (Si 2) (35 microns), and to bolometric luminosities in M82 are similar to those in M42, M17, and Sgr A. These similarities, and the association of the bulk of the (O 1) and (Si 2) emission with the ionized emission, suggest that the dominant emission mechanism for (O 1) and (Si 2) in M82 is the same as in these Galactic regions, namely warm gas photodissociated by UV flux from the OB stars responsible for the nearby H 2 regions. We argue that shock or x ray heated gas or H 2 plasma is a minor contributor to the intensities of these fine structure lines. Both the (O 1) (53 microns) and the (Si 2) (35 microns) spectrum show an asymmetric line profile indistinguishable in shape from those of the (O 3) (52 and 88 microns) and (N 3) (57 microns) lines and similar to that of the more extended (C 2) 158 micron line measured previously in M82. We detect two distinct velocity components, which we attribute to emission from two regions at either end of the central bar, where the bar connects to an orbiting torus of neutral gas seen in H 1 and CO J = 1-0. We model separately the two velocity components and derive the physical conditions in these two regions. The clouds in these regions are small, R approx. 1-2 pc, have warm neutral gas surfaces, T approx. 200 K, and are concentrated with volume filling factors of approx. 0.02 and area filling factors of 1-5. The entire central region (R approx. 700 pc) is characterized by a large number, approx. 5 x 10(exp 4), of 2 x 10(exp 3) solar mass clouds with surface densities of approx. 3 x 10(exp 4) cm(exp -3), illuminated by FUV fluxes 10(exp 4) times the average local interstellar value for the Milky Way. These clouds reside in the harsh conditions of a starburst nucleus, with photoevaporation times of 10(exp 6) yr, and collision timescales only about an order of magnitude longer.

Lord, Steven↗
NASA NTRS1977

Techniques for increasing boron fiber fracture strain

Improvement in the strain-to-failure of CVD boron fibers is shown possible by contracting the tungsten boride core region and its inherent flaws. The results of three methods are presented in which etching and thermal processing techniques were employed to achieve core flaw contraction by internal stresses available in the boron sheath. After commercially and treatment induced surface flaws were removed from 203 micrometers (8 mil) fibers, the core flaw was observed to be essentially the only source of fiber fracture. Thus, fiber strain-to-failure was found to improve by an amount equal to the treatment induced contraction on the core flaw. Commercial feasibility considerations suggest as the most cost effective technique that method in which as-produced fibers are given a rapid heat treatment above 700 C. Preliminary results concerning the contraction kinetics and fracture behavior observed are presented and discussed both for high vacuum and argon gas heat treatment environments.

Dicarlo, J. A.↗