Search NASA⌕ Search

SEARCH · Search NASA

Results for “GAS WELDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Microstructure-Property Correlations in Fiber Laser Welded Nb-Ti Microalloyed C-Mn Steel

Mechanical Performance of traditional gas-shielded arc welded joints of 700 MPa grade microalloyed C-Mn steel cannot meet service requirements. Laser welding, with its characteristic high energy density, is known to improve the welding performance of experimental steels. In the present study, Nb-Ti microalloyed steel with a thickness of 4.5 mm was welded using a 4 kW fiber laser. The microstructure, precipitation, and mechanical properties of the welded joints were studied. The hardness and tensile strength of the welded joints were higher than those of the base metal (BM). The microstructure of the fusion zone (FZ) and coarse grain heat affected zone (CGHAZ) was lath martensite (LM), while the microstructure of the fine grain HAZ and mixed grain HAZ consisted of ferrite and martensite/austenite islands. Although LM was observed in both the FZ and CGHAZ, the hardness and calculated tensile strength of the FZ were lower than those of the CGHAZ, due to a reduction in solid solution strengthening by element loss and the dissolution of high-hardness precipitates in FZ. Most precipitates such as [(Nb,Ti)C and (Nb,Ti)(C,N)] that were present in the BM were dissolved, which led to an increase in C and N in solid solution in the FZ. Thus, the elastic modulus of the FZ was higher than that of the BM. Similarly, the elastic modulus of the CGHAZ was higher than that of the BM due to the segregation of C and N atoms during the welding process. The toughness of the FZ was superior to that of the BM, and the toughness of the HAZ approached 91% of that of the BM. The change in toughness primarily depended on the microstructural refinement, the increase in the fraction of grains with high misorientation, the residual austenite in the FZ and CGHAZ, and the dissolution of coarse precipitates.

36 MATERIALS SCIENCE↗

Evolution of carbide precipitates in Hastelloy N joints during welding and post weld heat treatment

Highlights: • The formation and spheroidization of the eutectic-like carbides are found in the Hastelloy N alloy during welding and PWHT. • All precipitates in the joints before and after the PWHT are identified as a M{sub 6}C type carbide with different morphology. • The diffusion of main element of Mo leads to the decrease of lattice parameter of the carbide during the welding and PWHT. - Abstract: The effects of welding and post weld heat treatment (PWHT) on the morphology, composition and lattice parameter of the precipitates in the welding joints of Hastelloy N alloy have been investigated. Joint samples were prepared using a gas tungsten arc welding process with ERNiMo-2 fillers, and then solid-solution treated at 1100 °C for 20 min. After welding, eutectic M{sub 6}C carbides can be observed in the heat affected zones (HAZ) and weld zones (WZ). These eutectic M{sub 6}C carbides become spheroidized during the following PWHT. The concentration of Si decreases during the transformation from the primary ones to eutectic ones, and then increases during the spheroidizing process. The total concentration of Si + Cr in M{sub 6}C carbides remains stable during welding and PWHT. At the same time, the heat leads to the outward diffusion of Mo from the M{sub 6}C carbides, which results in a decrease of the lattice parameter.

36 MATERIALS SCIENCE↗

Comparative study of microstructure and properties of low-alloy-steel/nickel-based-alloy interfaces in dissimilar metal weld joints prepared by different GTAW methods

Highlights: • Number of type I and type II boundaries: H-DMWJ > C-DMWJ > W-DMWJ. • Width carbon depleted zones and carbon enriched zones: H-DMWJ > C-DMWJ > W-DMWJ. • Type I and type II boundaries are susceptible to SCC and cracked during mechanical bending. • C-DMWJ has the best performance while H-DMWJ has the worst one. - Abstract: Low-alloy-steel/buttering (or welding) metal interfaces in safe-end dissimilar metal weld joints (DMWJs) at nuclear power plants are weak parts. To optimize the quality of the safe-end DMWJs used for the construction of domestic nuclear power plants and to improve the welding productivity, a series of DMWJs in full-size have been manufactured by using different gas tungsten arc welding (GTAW) methods. The microstructure, chemical composition distribution and local properties across the SA508/52(M) interfaces in these DMWJs are studied. The high heat input and long high temperature duration during hot-wire GTAW process promote the carbon diffusion and grain boundary migration and hence the DMWJ by hot-wire GTAW has the largest amount of type I and type II boundaries and the widest carbon depleted zones and carbon enriched zones, which resulting in the worst performance among the DMWJs in simulated primary water. Type I and type II boundaries are high angle random grain boundaries (RGBs) and Cr-depleted zones are found along type II boundaries resulting in their high susceptibility to SCC. In addition, these boundaries are prone to be cracked during mechanical bending process.

36 MATERIALS SCIENCE↗

High-Speed and High-Quality Field Welding Repair Based on Advanced Non-Destructive Evaluation and Numerical Modeling

Creep strength-enhanced ferritic (CSEF) steels such as Grade 91 (9Cr-1Mo-V) and Grade 92 (Fe-9Cr-2W-0.5Mo) steels are widely used in the fossil-fuel-fired and nuclear power plants. The weld integrity of these steels is crucial for power plants' safe and reliable operations. Due to harsh service conditions, the steel weld can become susceptible to environmental degradation. Field welding repair is used to restore the degraded weld’s performance where a controlled temper-bead welding technique is commonly used to temper the freshly formed martensite during welding. However, knowledge of weld repairability is limited and experimental trial and error optimization to achieve desired microstructure and joint properties is expensive and time-consuming. Many existing computational models, e.g., finite element models, are limited to solving heat conduction equation and ignoring convective heat transfer due to molten metal flow. These models can result in over-prediction of peak temperatures of weld pool and heat-affected zone (HAZ), which in turn can affect the accuracy of tempering prediction. Moreover, these finite element models require an input of the deposit profiles in advance and thus limits the usability of these models. Here, a molten pool-based, multi-pass multi-layer model has been developed based on computational fluid dynamics (CFD) approach with the Volume of Fluid (VOF) method. The model calculates the bead formation, thereby eliminating the need for pre-determined bead profiles required by finite element models. For computational efficiency, a coordinate system attached to the moving heat source is utilized. A subroutine is developed to convert the temperature profiles in the reference frame stationary to the heat source to that stationary to the workpiece. The converted thermal cycles are then imported into a microstructure model to compute the tempering kinetics and resultant hardness using a Johnson-Mehl-Avrami-Kolmogorov (JMAK), and modified Grange-Baughman parameter. The modeling approach is first developed and validated on single- and multi-pass deposition of stainless steel filler metal onto a SA-533 high strength steel substrate. The models are then applied to a multi-pass V-groove repair weld of Grade 91 steel plate as well as directed energy deposition of Grade 92 steel. Non-destructive characterization of microstructures was performed on Grade 91 and 92 steel welds. Two welding processes, cold metal transfer (CMT) and flux-cored arc welding (FCAW), were investigated for the Grade 91 steel weld samples. For the Grade 92 weld samples, three different heat inputs (low, medium, and high) of gas tungsten arc welding (GTAW) were utilized to replicate traditional field welding processes. The non-destructive evaluation (NDE) method used for this research was immersion ultrasonic testing (UT) using a micro-resolution ultrasonic imaging methodology specifically designed to operate in the through-transmission configuration operating at 20 MHz of frequency. The system used a focused ultrasonic beam spot size diameter between 250-300 μm, and a 6 μm laser vibrometer spot size for detection, to produce highly defined images with longitudinal and mode-converted shear waves. From the micro-resolution ultrasonic C-scan images, three microstructural regions, i.e., weld metal (WM), HAZ, and base metal (BM), were clearly identifiable. Various levels of ultrasonic amplitudes distributed over the three regions were correlated with electron beam backscattered diffraction (EBSD) images using grain size, grain boundaries, and dislocation densities. The results showed that areas with relatively higher ultrasonic amplitude levels were associated with smaller grains and higher dislocation densities, while areas with lower amplitude levels were associated with larger grains and lower dislocation densities. In addition, ultrasonic velocity data obtained across the three different weld microstructural regions of Grade 91 test samples were correlated with optical metallographic images and hardness measurements. The results showed distinctive decreases in ultrasonic velocity and hardness over the HAZ region, where weld failures often occur during service.

36 MATERIALS SCIENCE↗

Monitoring Weld Pool Surface and Penetration Using Reversed Electrode Images

The three­-dimensional weld pool top surface shape provides important informa­tion about the state of weld penetration during welding. In this study, a method was developed to quantitatively relate weld pool surface height to the reversed electrode image (REI) on the weld pool surface. This new feature was extracted from the weld pool image using a passive vision-­based monitoring system during gas tungsten arc welding (GTAW). Due to the specular reflection of the weld pool top surface, the REI is visible on the weld pool surface during GTAW. The position of the REI was determined with a robust image processing algorithm. Based on the principle of light reflection, the distance between the electrode tip and the REI (DERI) was related to the weld pool surface height. By assuming the weld pool surface was a spherical mirror, a reflection model was established to calculate the surface height (SH) index based on the measurement of the DERI, arc length, and weld pool geometry. The pro­posed method was verified with bead­-on­plate welding experiments. The SH was positively related to the face reinforcement or depression of the weld bead. This method was applied to monitor the penetration state during bead­on­plate autoge­nous welding, particularly when a complete penetration weld was formed.

42 ENGINEERING↗

Modeling of Keyhole-Induced Pore Formation in Laser-Arc Hybrid Welding of Aluminum Alloy with a Horizontal Fillet Joint

A three-dimensional transient model is proposed to investigate the weld pool dynamic behavior in laser + metal inert gas (MIG) hybrid fillet welding of aluminum alloy in the horizontal position, which allows for the joint configuration and coupling of the keyhole, droplet and weld pool as well as the heat and mass exchange between gas and liquid phases and is able to simulate the temperature distribution, fluid flow and formation process of a keyhole-induced pore in hybrid welding with a horizontal fillet joint. The weld porosity is also measured using x-ray nondestructive testing technology. Keyhole behavior and the formation mechanism of keyhole-induced porosity were analyzed. The calculated results are in generally good agreement with the experimental ones. A clockwise vortex always exists at the middle part of the weld pool. The formation and growth of the molten metal bulge on the keyhole wall are responsible for the occurrence of a gas bubble, which has a variation in size and shape and can be split during welding. The keyhole collapses easily at its middle or upper part in horizontal fillet welding, and the capture of the bubble by the upper molten pool boundary enhances the possibility of porosity formation to some degree. The keyhole-induced pore is mainly formed at the regions near the keyhole bottom and the upper fusion line of the weld pool.

36 MATERIALS SCIENCE↗

Assessment of Mechanical Properties for Dissimilar Metal Welds: A Nondestructive Approach

Several engineering components are fabricated by joining similar or dissimilar materials. In the present investigation, welded joints between low alloy steel and austenitic stainless steel were considered. This assembly is one of the critical components in the heat transport system of water-cooled reactors of nuclear power plants. 309L austenitic stainless steel and IN 182 alloys were used for buttering low alloy steel during fabrication of joints. Weld metal was 308L austenitic stainless steel and IN 182, respectively, for the two assemblies. Buttering by 309L SS was performed by gas tungsten arc welding, and the same was done by shield metal arc welding at the time of applying IN 182. Joining of 304L SS and buttered assembly in both the cases was carried out by shield metal arc welding. Evaluation of Vickers micro-hardness was done across the weld centerline for both joints. Microstructure of different regions was examined for the joints. Apart from conventional destructive tests, ultrasonic evaluation of joints was also carried out to ensure weld integrity. In this respect, ultrasonic velocity in longitudinal and shear mode was measured along the transverse direction of the weld. Young’s modulus was determined using ultrasonic tests as well as from the average hardness of different regions. The obtained Young’s modulus by two different techniques revealed satisfactory co-relation. The Young’s modulus obtained from ultrasonic measurements was used to determine the yield strength of different regions across the welds. This technique proved to be useful in identifying the failure prone area across the welded joint.

36 MATERIALS SCIENCE↗

Welded and Hydrogen Charged Zircaloy-4 and Welded Stainless Steel 347 Property Data and Microstructures for the Target Solution Vessel and Support Lines of SHINE

SHINE Medical Technologies is developing a facility that will produce molybdenum-99 for medical isotope procedures. As part of this facility, a metal tank, called the target solution vessel (TSV), will hold a uranyl sulfite solution. The TSV must withstand neutron irradiation near room temperature and potential corrosion from the aqueous solution. The large cylindrical TSV will be fabricated by welding and will have numerous pipes and connections also attached via welding. The vessel and those pipes will have varying thicknesses so both gas tungsten arc welding (GTAW) and flux-cored arc welding (FCAW) will be necessary to fabricate different sections. The original material under consideration for the TSV was Zircaloy-4 (Zry-4), but it is known to form a hydride which can degrade its mechanical properties. Thus, some investigation here is focused on the effects of hydrogen uptake in the Zry-4. Additionally, the alternative material being considered is AISI 347, a stainless steel. Both materials have little existing data for their neutron irradiation behavior below 100°C, and both have open questions on the weld behavior under neutron irradiation. Testing has focused on characterizing their weld properties with tensile tests and performing neutron irradiation of samples in the High Flux Isotope Reactor (HFIR) at Oak Ridge National Laboratory (ORNL).

07 ISOTOPE AND RADIATION SOURCES↗

Characterization of microstructures and mechanical properties of Inconel 617/310 stainless steel dissimilar welds

The microstructure and mechanical properties of Inconel 617/310 austenitic stainless steel dissimilar welds were investigated in this work. Three types of filler materials, Inconel 617, Inconel 82 and 310 austenitic stainless steels were used to obtain dissimilar joint using the gas tungsten arc welding process. Microstructural observations showed that there was no evidence of any possible cracking in the weldments achieved by the nickel-base filler materials. The welds produced by 617 and 310 filler materials displayed the highest and the lowest ultimate tensile strength and total elongation, respectively. The impact test results indicated that all specimens exhibited ductile fracture. Among the fillers, Inconel 617 exhibited superlative fracture toughness (205 J). The mechanical properties of the Inconel 617 filler material were much better than those of other fillers. - Research Highlights: {yields} A fine dendritic structure was seen for the Inconel 617 weld metal. {yields} A number of cracks were initiated when the 310 SS filler metal was used. {yields} All welded samples showed ductile fracture. {yields} The Inconel 617 filler material presents the optimum mechanical properties.

36 MATERIALS SCIENCE↗

Optimization of a Welding Procedure for Making Critical Aluminum Welds on the LBNF Absorber Core Block

The LBNF Absorber consists of thirteen 6061-T6 aluminum core blocks. The core blocks are water cooled with de-ionized (DI) water which becomes radioactive during beam operations. The cooling water flows through gun-drilled channels in the core blocks. A weld quality optimization was performed to produce National Aeronautical Standard 1514 Class I quality welds on the aluminum core blocks. This was not successful in all cases. An existing Gas Tungsten Arc Welding Procedure Specification was fine tuned to minimize, in most cases, and eliminate detect-able tungsten inclusions in the welds. All the weld coupons, however passed welding inspection as per the piping code: ASME B31.3 Normal Fluid Service. Tungsten electrode diameter, type, and manufacturer were varied. Some of the samples were pre-heated and others were not. It was observed that larger diameter electrodes, 5/32 in., with pre-heated joints resulted in welds with the least number of tungsten inclusions. It is hypothesized that thinner electrodes breakdown easily and get lodged into the weld pool during the welding process. This breakdown is further enhanced by the large temperature differential between the un-preheated sample and the hot electrode.

43 PARTICLE ACCELERATORS↗

Optimization of a Welding Procedure for Making Critical Aluminum Welds on the LBNF Absorber Core Block

he LBNF Absorber consists of thirteen 6061-T6 aluminum core blocks. The core blocks are water cooled with de-ionized (DI) water which becomes radioactive during beam operations. The cooling water flows through gun-drilled channels in the core blocks. A weld quality optimization was performed to produce National Aeronautical Standard (NAS) 1514 Class I quality welds on the aluminum core blocks. This was not successful in all cases. An existing Gas Tungsten Arc Welding (GTAW) Welding Procedure Specification (WPS) was fine tuned to minimize, in most cases, and eliminate detectable tungsten inclusions in the welds. All the weld coupons however, passed welding inspection as per the piping code: ASME B31.3 Normal Fluid Service. Tungsten electrode diameter, type, and manufacturer were varied. Some of the samples were pre-heated and others were not. It was observed that larger diameter electrodes, 5/32 in., with pre-heated joints resulted in welds with the least number of tungsten inclusions. It is hypothesized that thinner electrodes breakdown easily and get lodged into the weld pool during the welding process. This breakdown is further enhanced by the large temperature differential between the un-preheated sample and the hot electrode.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Report on FY 2023 Welding R&D at ORNL in support of ASME Alloy 709 Code Case Development

As part of the Alloy 709 (A709) ASME Code Case development effort under the Advanced Reactor Technologies (ART) Program, this work covers the development of the technical basis for weld fabrication and weld qualification of A709. This report summarizes the A709 welding research conducted at Oak Ridge National Laboratory (ORNL) in FY 2023. One of the focuses of the A709 welding research at ORNL is to relax the restriction of the P content in the A709 filler metal weld wire. In this report, we show the success in welding of high phosphorus (P) commercial A709 plates using A709 weld wires with relaxed P content of 80 wppm. A test weld was fabricated with the 80 wppm weld wire on the first commercial heat A709 base metal with 140 wppm P content using gas tungsten arc welding (GTAW). The test weld passed all weld qualification tests without issues. This study concludes that A709 matching filler metal with moderate amount of P of less than 80 wppm could be used to produce code qualified A709 welds with standard welding process without special treatment. It is recommended that the P level in the weld wire to be kept low to avoid hot cracking. Cross-weld specimens were machined from the two A709 production welds.. Cross welding creep rupture Code Case testing on these two production welds was initiated . The preliminary cross-weld creep tests results continue to show little or no creep strength reduction relative to the base metal.

36 MATERIALS SCIENCE↗

Effect of Through-Thickness Friction Stir Processing Parameters on Weld Repair and Modification of Fusion-Welded AA6061 Aluminum Alloy

Through-thickness friction stir processing was successfully carried out for microstructure modification and elimination of fusion defects of the gas metal arc welds by applying the process on as-welded joints. Variation in rotational speed from 750 to 1050 rpm and traveling speed from 50 to 200 mm/min resulted in minor changes (approximately 1 µm) in the grain size of nugget zone, while this variation in elongation result was up to 40%. The hardness profile, the width of softening zone, minimum hardness and fracture location also changed for different processing conditions. Furthermore, the defects were vanished efficiently across the welds profile by this method. The results also verified the geometric dynamic recrystallization phenomena as a dominant mechanism of microstructural modification.

36 MATERIALS SCIENCE↗

Integrated Recycling Test Fuel Fabrication

The Integrated Recycling Test is a collaborative irradiation test that will electrochemically recycle used light water reactor fuel into metallic fuel feedstock. The feedstock will be fabricated into a metallic fast reactor type fuel that will be irradiation tested in a drop in capsule test in the Advanced Test Reactor on the Idaho National Laboratory site. This paper will summarize the fuel fabrication activities and design efforts. Casting development will include developing a casting process and system. The closure welding system will be based on the gas tungsten arc burst welding process. The settler/bonder system has been designed to be a simple system which provides heating and controllable impact energy to ensure wetting between the fuel and cladding. The final major pieces of equipment to be designed are the weld and sodium bond inspection system. Both x-radiography and ultrasonic inspection techniques have been examine experimentally and found to be feasible, however the final remote system has not been designed. Conceptual designs for radiography and an ultrasonic system have been made.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗