Search NASA⌕ Search

SEARCH · Search NASA

Results for “HULL - IMPACT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-boat Hull - N.A.C.A. Model No.11-A

Model No. 11-A was designed as an improvement over N.A.C.A. Model No. 11, a complete test of which is described in N.A.C.A. Technical Note No. 464. In contrast with the longitudinal upward curvature in the planing bottom forward of the main step on Model 11-A was made as flat as practicable. Otherwise, the two models have very nearly the same form. The results of towing tests made on Model 11-A in the N.A.C.A. tank over a wide range of speed, load on the water, and trim angle are presented, both as original test data and as non dimensional coefficients. A comparison is made with similar results from the test of Model No. 11. The practical significance of the improvement obtained is demonstrated by applying the data from the new form to the illustrative design problem use in the note on Model NO. 11.

Parkinson, John B↗
NASA NTRS1935

The effect of depth of step on the water performance of a flying-boat hull model

NACA model 11-C was tested with four different depths of step to obtain information as to the effect of the depth of step on the water performance. The depths of step were selected to cover the practicable range of depths and in each case the included angle between the forebody and afterbody keels was kept the same 6-1/2 degrees. Small depths of step were found to give lower resistance at speeds below and at the hump speed of the model and greater depths of step lower resistance at high speeds. For low resistance throughout the speed range of the model investigated the most desirable depth of step is from 2.5 to 4.0 percent of the beam. The change of the best trim angle caused by variation of the depth of step was not appreciable. Increased depth of step caused increases in the maximum positive trimming moments at all trim angles investigated.

Bell, Joe W↗
NASA NTRS1935

Tank Tests of a Model of a Flying-boat Hull Having a Longitudinally Concave Planing Bottom

The NACA model 11-B, which has a longitudinally concave planing bottom forward of the step, was tested over a wide range of loading. The results of the tests are presented as curves of resistance and trimming moment plotted against speed for various trim angles and as curves of resistance coefficient at best trim angle, and trimming-moment coefficient. The characteristics of the form at the optimum trim are compared with those of NACA model 11-C which has the same form with the exception of a planing bottom longitudinally straight near the step. Photographs of the models being towed in the tank are included for a comparison of the spray patterns. At the best angles of trim in each case model 11-B has lower resistance at high speeds, a higher maximum positive trimming moment near the hump speed, and a more favorable spray pattern than of model 11-C.

Parkinson, J B↗
NASA NTRS1933

A complete tank test of a model of a flying-boat hull-N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M↗