Search NASA⌕ Search

SEARCH · Search NASA

Results for “High activity”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2021

High Mg activation in implanted GaN by high temperature and ultrahigh pressure annealing

Not provided.We demonstrate high p-type conductivity and hole concentrations >10 18 cm -3 in Mg-implanted GaN. The implantation was performed at room temperature and by post-implantation annealing at 1 GPa of N 2 and in a temperature range of 1200–1400 °C. The high pressure thermodynamically stabilized the GaN surface without the need of a capping layer. We introduce a “diffusion budget,” related to the diffusion length, as a convenient engineering parameter for comparing samples annealed at different temperatures and for different times. Although damage recovery, as measured by XRD, was achieved at relatively low diffusion budgets, these samples did not show p-type conductivity. Further analyses showed heavy compensation by the implantation-induced defects. Higher diffusion budgets resulted in a low Mg ionization energy (~115 meV) and almost complete Mg activation. For even higher diffusion budgets, we observed significant loss of Mg to the surface and a commensurate reduction in the hole conductivity. High compensation at low diffusion budgets and loss of Mg at high diffusion budgets present a unique challenge for shallow implants. A direct control of the formation of compensating defects arising from the implantation damage may be necessary to achieve both hole conductivity and low Mg diffusion.

36 MATERIALS SCIENCE↗
DOE OSTI2022

What Is the Right Level of Activation of a High-Spin {FeNO} 7 Complex to Enable Direct N–N Coupling? Mechanistic Insight into Flavodiiron NO Reductases

Flavodiiron nitric oxide reductases (FNORs), found in pathogenic bacteria, are capable of reducing nitric oxide (NO) to nitrous oxide (N 2 O) to detoxify NO released by the human immune system. Previously, we reported the first FNOR model system that mediates direct NO reduction (Dong, H. T.; et al. J. Am. Chem. Soc. 2018, 140, 13429-13440), but no intermediate of the reaction could be characterized. Here, we present a new set of model complexes that, depending on the ligand substitution, can either mediate direct NO reduction or stabilize a highly activated high-spin (hs) {FeNO} 7 complex, the first intermediate of the reaction. The precursors, [{Fe II (MPA-(RPhO) 2 )} 2 ] (1, R = H and 2, R = t Bu, Me), were prepared first and fully characterized. Complex 1 (without steric protection) directly reduces NO to N 2 O almost quantitatively, which constitutes only the second example of this reaction in model systems. Contrarily, the reaction of sterically protected 2 with NO forms the stable mononitrosyl complex 3, which shows one of the lowest N-O stretching frequencies (1689 cm -1 ) observed so far for a mononuclear hs-{FeNO} 7 complex. Here this study confirms that an N-O stretch & LE;1700 cm -1 represents the appropriate level of activation of the FeNO unit to enable direct NO reduction. The higher activation level of these hs-{FeNO} 7 complexes required for NO reduction compared to those formed in FNORs emphasizes the importance of hydrogen bonding residues in the active sites of FNORs to activate the bound NO ligands for direct N-N coupling and N2O formation. The implications of these results for FNORs are further discussed.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1982

Interplanetary magnetic field control of high-latitude activity on July 29, 1977

Multisatellite particle and magnetic field data for the substorms of July 29, 1977, show auroral-like activity above 80 deg invariant latitude during the recovery period. The movement of auroral zone activity to high latitudes followed the substorm sequence, at which time the inferred interplanetary magnetic field (IMF) was strongly northward. Electron energy spectra indicative of a field-aligned potential drop, and the absence of supporting precipitating ions, are found at latitudes greater than 80 deg. The north-south symmetry of these observations suggests that the events are on closed field lines. It is noted the very strong northward IMF connected to the sunward tilted geomagnetic dipole field plays a role in the driving of strong Birkeland and ionospheric current systems in the northern polar regions, while eliminating them from the southern polar regions.

Zanetti, L. J.↗
DOE OSTI2020

Removal of High Specific Activity Fission Products from Uranyl Sulfate Waste Solutions

The Savannah River National Laboratory (SRNL) is currently providing support to SHINE Medical Technologies (SHINE) which plans to deploy a low energy, accelerator-based neutron source to fission low enriched U in a uranyl sulfate target solution for 99 Mo production. The 99 Mo is initially separated from the fission products and target solution by an extraction column. Subsequent washing of the column will generate waste solutions containing residual U and fission product activity. A small number of high specific activity fission products (e.g., 90 Sr, 137 Cs, and 144 Ce) in these streams will likely control the classification of the low level waste (LLW). If a sufficient amount of the high specific activity isotopes are separated from the SHINE waste streams and concentrated into a waste form, it would be possible to treat a majority of the wash solutions from the column operations as a lower class of LLW (Class A versus Class B or C or Class B versus Class C). The high specific activity fission product elements could then be dispositioned as a much smaller volume of waste rather than requiring the disposal of the entire waste stream at the higher waste classification. The Savannah River Site (SRS) has experience with using monosodium titanate (MST) and crystalline silicotitanate (CST) to remove Cs and Sr from high salt content waste solutions generated during the reprocessing of nuclear fuels and targets. Both of these materials have worked very well for their intended purposes at the SRS where the fission product elements are removed from highly alkaline waste. On the other hand, SHINE waste streams from the extraction column contain H 2 SO 4 which makes the solution acidic. Additionally, the SRS waste streams do not contain other fission product elements such as transition metals or lanthanides because they precipitate upon neutralization of the SRS waste and are not present in the supernate which is dispositioned as LLW following treatment. As such, there are inherent differences between SHINE and SRS waste treatment strategies. Savannah River National Laboratory was tasked with performing scoping studies to see if MST and CST would remove Sr, Cs, and Ce from an acidic mixed metal simulant solution. Batch contact experiments were performed using MST and two CST type materials. The MST material is a 15 wt % powder in 0.15 M NaOH slurry. The MST showed low adsorption for elements of interest from acidic solution. Furthermore, the powder size makes MST non-ideal for column operations. A CST IE-911 ion exchange material had high Cs adsorption, moderate Sr, and marginal Ce adsorption. Based on adsorption of all species, the ion exchange capacity was found to be 0.032 meq/mL. A bench-top column experiment to measure elemental breakthrough curves was performed using CST IE-911 where chromatographic separations of the mixed simulant were expected to occur. While most elements behaved as expected, the lanthanide series, containing Ce, broke though the column earlier than expected. The second CST material, CST R9120, displayed high adsorption for all elements in the acidic mixed simulant solutions in a batch contact study, and had a calculated loading capacity of 0.091 meq/mL. Future studies to develop a waste treatment flowsheet should focus on CST R9120 to treat SHINE waste solutions.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Dual‐Gradient Construction on Li‐Rich Cathodes for High Stability Lithium Battery

Abstract The practical applications of high‐energy Li‐rich layered oxides (LLOs) have been hindered by the severe performance degradation including voltage decay and capacity fading. The gradient construction toward high‐activity interior and high‐stability exterior, typically realized by gradually changed transition metal (TM) gradient in LLOs, can alleviate the performance degradation to certain degrees. In this study, a gradient design of Al/Mg dopants is demonstrated for the TM‐gradient LLOs to further harmonize the high‐activity interior and high‐stability exterior, thereby forming the dual (TM and doping) gradient. As a result, superior capacity retention of 86% and a minor voltage decay of 0.54 mV cycle −1 are achieved at 1 C after 300 cycles. The improved electrochemical stability of the dual‐gradient LLO is attributed to the enhanced surface stability and suppressed bulk structure degeneration of LLOs upon electrochemical cycling. The dual‐gradient design serves as an important approach to fabricate high‐performance bulk LLOs toward applications.

Wu, Tianhao↗
DOE OSTI2020

Overcoming challenges to support US resumption of high specific activity cobalt-60

Domestic production of high specific activity 60 Co was halted after a target rupture in 2012 at the Advanced Test Reactor (ATR). The Isotope Program (IP) within the US Department of Energy (DOE) Office of Science tasked a multilaboratory team of researchers and managers from Oak Ridge and Idaho National Laboratories with the redesign the radioisotope capsule. The objective of this effort was to create a more robust and reliable design, compared to the pre-2012 target. The team successfully completed this task to produce the DOE-IP cobalt (Co) production capsule design. Furthermore, 66 capsules were successfully fabricated by Oak Ridge National Laboratory (ORNL) and delivered to Idaho National Laboratory (INL) for irradiation in the ATR between January 2014 and October 2016. This paper describes the efforts of the team to prepare and disposition the two initial DOE-IP Co production capsules that were processed in March 2020. These efforts include performing accurate production predictions, experimentally validating predictions with assay measurements, shipping with the Orano-furnished Battelle Energy Alliance Research Reactor shipping package, and disassembling capsules at the isotope vendor site.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Degradation of Magnetic Materials for High-Temperature Active Magnetic Bearing Applications in CO₂-Based Environments

High-temperature Active Magnetic Bearings (AMBs) are a promising alternative to conventional bearings in hermetically sealed turbomachinery for supercritical CO₂ (sCO₂) systems. They offer reduced CO₂ leakage, lower windage losses, enhanced misalignment tolerance, reduced wear, and built-in diagnostic capabilities. A critical challenge, however, is ensuring long-term material stability in harsh CO₂-rich environments. This study investigated the degradation behavior of permanent and soft magnetic materials (Alnico 9C, Alnico 5-7C, SmCo 18-T550, Hiperco-50, and coated variants) after up to 6,000 hours of exposure in gaseous CO₂, sCO₂, or air at 450 °C and 550 °C. The evaluation included post-exposure mass change measurements, scanning electron microscopy (SEM) analysis, and magnetic property assessments. The results demonstrate oxidation rates, microstructural evolution, and retention of magnetic performance across conditions. The findings offer essential insights into the thermal corrosion behavior of magnetic materials under CO₂ rich environments and serve as a reference for material selection in AMB system designs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

In-Canal Assay of High Specific Activity 60 Co at the Advanced Test Reactor

Production of high specific activity (HSA) 60 Co has recently resumed at the Advanced Test Reactor (ATR) at the Idaho National Laboratory. The technical steps of performing in-canal assay of HSA 60 Co targets at the ATR are described herein. The HSA targets are assayed on a regular basis, between cycles at the ATR, in order to assess the progress of activation. The targets are also assayed at the conclusion of the irradiation in order to provide activity estimates for the distributor and to be used for safety and shipping evaluations. These target assay activities must take place in the ATR canal to provide sufficient radiological shielding. Furthermore, a specialized assay fixture is used in conjunction with custom 60 Co radiation standards to assess the irradiated target. The specific activity of each irradiated target was determined by first measuring the 60 Co standards to determine a sensitivity factor. Then, each irradiated target was measured, and the integrated measurement was multiplied by the sensitivity factor to determine the total activity of the irradiated target. Finally, a correction factor was determined to adjust the reported activity, accounting for differences in the physical geometries of the standards and targets. These methods were used to accurately assay the gross activity of nine irradiated 60 Co targets, two of which were delivered to the distributor where confirmatory hot-cell assays were performed verifying the accuracy of the in-canal assay method.

07 ISOTOPE AND RADIATION SOURCES↗
NASA NTRS2012

Highly Stable and Active Catalyst for Sabatier Reactions

Highly active Ru/TiO2 catalysts for Sabatier reaction have been developed. The catalysts have shown to be stable under repeated shutting down/startup conditions. When the Ru/TiO2 catalyst is coated on the engineered substrate Fe-CrAlY felt, activity enhancement is more than doubled when compared with an identically prepared engineered catalyst made from commercial Degussa catalyst. Also, bimetallic Ru-Rh/TiO2 catalysts show high activity at high throughput.

Hu, Jianli↗
DOE OSTI2026

Finding the Pareto front for high-entropy-alloy catalysts

Finding catalysts that have both high activity and high stability presents a long-standing challenge. Since optimizing activity and stability are conflicting objectives, the best one can do is find the Pareto front that yields optimal tradeoffs between these features. On the Pareto front, there is a trade-off where a portion of catalytic activity must be sacrificed to gain further stability and vice versa . Here, we provide a method to optimize the front by designing a multi-objective genetic algorithm that combines machine learning, graph neural network calculations, and density functional calculations. The application considered is the oxygen evolution reaction catalyzed by high-entropy alloys. We find that the Pareto front generally contains alloys with diverse elements, but that enhancing stability inevitably inflicts a toll on activity. We compare the general conclusions of our work to a survey of 545 experiments.

Zhang, Chengyi [Univ. of Auckland (New Zealand)]↗
DOE OSTI2022

Evaluation of 186 WS 2 target material for production of high specific activity 186 Re via proton irradiation: separation, radiolabeling and recovery/recycling

Enriched tungsten disulfide ( 186 WS 2 ) was evaluated at increasing proton beam currents (20-50 µA) and times (up to 4 h) on a GE PETtrace cyclotron for production of high specific activity (HSA) 186 Re. The HSA 186 Re was separated from the irradiated target as [ 186 Re][ReO 4 ] - by a liquid-liquid extraction method and radiolabeled with a new N 2 S 2 ligand (222-MAMA-N-ethylpropionate). The enriched 186 W was recovered from the extraction process, analyzed for purity and enrichment, and converted back to the disulfide ( 186 WS 2 ). The results demonstrate that the 186 WS 2 is an easily pressed target material that can withstand relatively high currents and can be readily recovered and recycled. The 186 Re produced was isolated in high specific activity and readily formed the radiotracers [ 186 Re][ReO(222-MAMA-N ethylpropionate)] and [ 186 Re][Re(CO) 3 (OH 2 ) 3 ] + .

186Re,N2S2 ligand↗
DOE OSTI2024

Amorphous Iridium Oxide-Integrated Anode Electrodes with Ultrahigh Material Utilization for Hydrogen Production at Industrial Current Densities

Herein, ionomer-free amorphous iridium oxide (IrO x ) thin electrodes are first developed as highly active anodes for proton exchange membrane electrolyzer cells (PEMECs) via low-cost, environmentally friendly, and easily scalable electrodeposition at room temperature. Combined with a Nafion 117 membrane, the IrO x -integrated electrode with an ultralow loading of 0.075 mg cm –2 delivers a high cell efficiency of about 90%, achieving more than 96% catalyst savings and 42-fold higher catalyst utilization compared to commercial catalyst-coated membrane (2 mg cm –2 ). Additionally, the IrO x electrode demonstrates superior performance, higher catalyst utilization and significantly simplified fabrication with easy scalability compared with the most previously reported anodes. Notably, the remarkable performance could be mainly due to the amorphous phase property, sufficient Ir 3+ content, and rich surface hydroxide groups in catalysts. Overall, due to the high activity, high cell efficiency, an economical, greatly simplified and easily scalable fabrication process, and ultrahigh material utilization, the IrO x electrode shows great potential to be applied in industry and accelerates the commercialization of PEMECs and renewable energy evolution.

08 HYDROGEN↗
NASA NTRS2006

Mars Odyssey: Off-nadir Imaging

Science Objectives for off-nadir imaging: a) Daily observations of high activity and high interest targets in the Polar Regions; b) Daily imaging of regions of gas jetting through vents and the formation of dark spots and fans; c) Increases likelihood of observing these processes in an active phase; d) Stereo imaging for geographical analysis and landing site characterization; and e) Fill in existing gaps and gores.

off nadir imaging↗
DOE OSTI2021

High-Performance Catalytic Four-Channel Hollow Fibers with Highly Dispersed Nickel Nanoparticles Prepared by Atomic Layer Deposition for Dry Reforming of Methane

In this study, highly dispersed nickel (Ni) nanoparticles (NPs) with an average particle size of 4.3 nm were uniformly deposited on the outer surface, the inner channel surface, and inside the pores of 20-cm long 4-channel α-Al 2 O 3 hollow fibers (HFs) by atomic layer deposition (ALD) for dry reforming of methane (DRM). Cerium oxide (CeO 2 ) was added to promote the catalytic performance of Ni/Al 2 O 3 -HF catalysts. Rationally designed filling methods, by tuning the reactor size and inert fillings, can reduce the catalyst bed voidage in a fixed bed reactor for better reactant gas distribution, effectively utilize the Ni reactive sites, and achieve excellent catalytic performance. It was found that the CeO 2 -promoted Ni/Al 2 O 3 -HF catalyst was highly active and highly stable without deactivation during an overall 400-hr DRM test at 850 ºC. CeO 2 with reversible valence states could participate in surface reactions; especially, the formation of CeAlO 3 provided sufficient surface Ce 3+ for CO 2 activation and enhanced the stability and reusability of the HF catalysts.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Kinetics and selectivity of methane oxidation on an IrO 2 (110) film

Undercoordinated, bridging O-atoms (O br ) are highly active as H-acceptors in alkane dehydrogenation on IrO 2 (110) surfaces but transform to HO br groups that are inactive toward hydrocarbons. The low C–H activity and high stability of the HO br groups cause the kinetics and product selectivity during CH 4 oxidation on IrO 2 (110) to depend sensitively on the availability of O br atoms prior to the onset of product desorption. From temperature programmed reaction spectroscopy (TPRS) and kinetic simulations, we identified two O br -coverage regimes that distinguish the kinetics and product formation during CH 4 oxidation on IrO 2 (110). Under excess O br conditions, when the initial O br coverage is greater than that needed to oxidize all the CH 4 to CO 2 and HO br groups, complete CH 4 oxidation is dominant and produces CO 2 in a single TPRS peak between 450 and 500 K. However, under O br -limited conditions, nearly all the initial O br atoms are deactivated by conversion to HO br or abstracted after only a fraction of the initially adsorbed CH 4 oxidizes to CO 2 and CO below 500 K. Thereafter, some of the excess CH x groups abstract H and desorb as CH 4 above ~500 K while the remainder oxidize to CO 2 and CO at a rate that is controlled by the rate at which Obr atoms are regenerated from HObr during the formation of CH 4 and H 2 O products. We also show that chemisorbed O-atoms ('on-top O') on IrO 2 (110) enhance CO 2 production below 500 K by efficiently abstracting H from Obr atoms and thereby increasing the coverage of O br atoms available to completely oxidize CH x groups at low temperature. Furthermore, our results provide new insights for understanding factors which govern the kinetics and selectivity during CH 4 oxidation on IrO 2 (110) surfaces.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗