Search NASA⌕ Search

SEARCH · Search NASA

Results for “High-Temperature Alloys”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

Wrought FeCrAl alloy (C26M) cladding behavior and burst under simulated loss-of-coolant accident conditions

Cladding burst experiments for FeCrAl cladding were performed in the Severe Accident Test Station facility at Oak Ridge National Laboratory. These experiments were simulated using the BISON fuel performance code to better understand the cladding plastic behavior and failure under simulated loss-of-coolant accident conditions. 3D cladding surface boundary conditions were generated using composite axial and azimuthal profiles from experiment thermocouple data. To improve the simulation analysis capabilities in BISON for cladding burst behavior, new thermal creep, plasticity, and failure stress models specific to C26M, a wrought FeCrAl alloy, were developed and implemented. Initial cladding burst results indicated a general underprediction in the failure temperature of the six cladding burst simulations versus the observed failure temperatures. Close investigation of the experiment timing versus the underlying tensile test data revealed that, compared with the tensile specimens, the cladding tubes did not experience the same long holding time at high temperatures. New tensile tests were performed at high temperatures using a temperature ramp similar to the simulated loss-of-coolant accident experiments. These new tensile curves showed an approximately 80% increase in the ultimate tensile strength of the C26M alloy, indicating that a holding time of 10 min at 700 °C and 800 °C allows annealing to change the material microstructure. Using the updated tensile properties, the burst temperatures and stresses from the simulations showed remarkable agreement with the experimental results. This study was then extended by varying the initial pressure to highlight the burst temperature difference between standard Zircaloy-4 and C26M cladding under equivalent conditions. The results show that C26M has a burst temperature that is approximately 70–130 K greater than that of Zircaloy-4. In conclusion, these modeling predictions can be further improved by collecting high-temperature tensile data for C26M beyond the temperature ranges used in this work.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Reduced order modeling of a fluidized bed particle receiver for concentrating solar power with thermal energy storage

Oxide particles can serve as both the heat transfer and thermal energy storage (TES) media for next-generation concentrating solar power (CSP) plants where high-temperature TES enables dispatchable electricity from efficient power cycles with firing temperatures above 600 °C. Transferring heat to flowing particles at such high temperatures in a MW-scale central tower receiver remains a challenge for the CSP community. For indirect receivers with external walls to contain the particles, maintaining wall temperatures below the limits of structural metal alloys requires high heat transfer coefficients between the wall and the moving particle stream. Bubbling fluidization of downward-flowing particles can sustain high bed-wall heat transfer coefficients (> 1000 W m -2 K -1 ). Using experimentally calibrated correlations for bed-wall heat transfer and vertical particle dispersion, this study implements an axially discretized zonal model of a counterflow fluidized bed receiver to explore how bubbling fluidization may enable indirect cavity particle receivers. High bed-wall heat transfer coefficients support solar fluxes on angled cavity walls > 200 kW m -2 at peak aperture fluxes of 980 kW m -2 while maintaining external wall temperatures < 950 °C. Lateral particle dispersion enables hotter particles near the receiver leading edge to mix with cooler particles further from the leading edge to lower maximum external wall temperatures. Parametric studies identify how mass fluxes, particle dispersion, and solar concentrations impact indirect receiver thermal efficiency and uniformity for a CSP plant. These studies provide a basis for the design of indirect fluidized-bed cavity receivers that can maintain particle outlet temperatures for TES above 750 °C.

14 SOLAR ENERGY↗
DOE OSTI2025

First-Principles Studies on Sc 2 RuZ (Z = Si, Ge, Sn) Inverse Heusler Alloys: Structural, Electronic, and Transport Properties

The continuous demand for efficient, nontoxic, and thermally stable materials for room-temperature energy conversion motivates the exploration of novel thermoelectric systems beyond the traditional magnetic Heusler alloys. While full and half-Heusler compounds, especially Co-, Ni-, and Mn-based systems, have demonstrated promising thermoelectric properties, their typically high operating temperatures and magnetic complexities limit their applicability in ambient thermal management. In this context, we investigate whether Sc-based inverse Heusler alloys can offer a viable nonmagnetic alternative with competitive thermoelectric performance. In this work, we perform a systematic first-principles study of the inverse Heusler compounds Sc 2 RuZ (Z = Si, Ge, Sn), focusing on their structural, electronic, mechanical, and thermodynamic-thermoelectric properties. Density Functional Theory (DFT) was employed to compute optimized lattice structures and band dispersion, while dynamical stability was assessed via phonon calculations. Thermoelectric transport coefficients, including Seebeck coefficient, electrical conductivity, and thermal conductivity, were estimated using the semiclassical Boltzmann transport theory within the constant relaxation time approximation. Our results show that all Sc 2 RuZ compounds are thermodynamically stable semiconductors with indirect band gaps of 0.12–0.16 eV and exhibit high elastic moduli, especially Sc 2 RuSn, which demonstrates superior stiffness and incompressibility. Importantly, all compounds display promising room-temperature thermoelectric characteristics, including high Seebeck coefficients and power factors. These findings reveal that Sc 2 RuZ alloys represent a rare class of stable, nonmagnetic inverse Heusler semiconductors with intrinsic thermoelectric potential at room temperature, unlike many existing Heusler systems optimized for spintronics or high-temperature operation. This work expands the known design space for Heusler-based thermoelectrics and offers a theoretical basis for experimental realization of efficient, low-temperature, nonmagnetic thermoelectric materials.

alloys↗
DOE OSTI2025

Versatile Cell Design for Molten Fluoride Salt Spectroscopy: Investigating Metal-Ion Speciation in Molten Fluoride Salts

Fluoride-based molten salts are widely used in industrial applications including aluminum production, thermal energy storage, optical crystal growth, and advanced nuclear reactor designs. Despite the wide range of uses, fundamental understandings of coordination chemistry and methods for probing molten fluorides are scarce, likely due to the difficulty of probing fluoride melts with spectroscopic techniques. Performing spectroscopic measurements of fluoride-based salts is challenging due to the highly corrosive nature of these salts, which can degrade many common optical materials. Here, in this work, we present a versatile optical cell design that enables spectroscopic measurements of corrosive melts. This innovative cell design overcomes the challenges posed by the corrosive nature of the salts, allowing for an accurate and consistent spectroscopic analysis. This work reports temperature-dependent absorption measurements for Co 2+ , Ni 2+ , and Cr 3+ analytes in LiF-NaF-KF eutectic salt (i.e., FLiNaK), which are common corrosion products originating from structural alloys in molten-fluoride handling. Absorption spectra were used to understand interactions of these analytes with FLiNaK, particularly ligand field coordination. The analysis of absorption spectra was complemented by structural analyses using ab initio molecular dynamics (AIMD) simulations, providing deeper insights into the behavior of the analytes in FLiNaK. Our findings indicate that the analytes studied in this work exist in octahedral or near-octahedral coordination states that remain stable across the temperature range of 500–600 °C. This work not only highlights an applied solution to performing optical spectroscopy in corrosive, high-temperature melts but also provides important fundamental insight on coordination behavior of transition-metal species in molten fluorides.

Fluoride salt spectroscopy↗
DOE OSTI2026

Mechanical behaviour of additively manufactured metals

Additive manufacturing is reshaping the production of engineering components in diverse industries, such as the automotive, aerospace, defense, and biomedical sectors, by offering unprecedented design flexibility. The non-equilibrium processing conditions of additive manufacturing generate materials with unique microstructures and tailored mechanical properties that are often unattainable through conventional routes. This review focuses on recent advances in additively manufactured metals that demonstrate distinctive mechanical behaviors, including strength-ductility synergy, microstresses and gradient plasticity, fracture and fatigue resistance, and high-temperature creep performance. Here, we examine the mechanisms and micromechanical effects arising from the heterogeneous microstructures fabricated by additive manufacturing, to guide the design of a wide range of high-performance structural materials. Furthermore, we discuss critical research needs and emerging opportunities in process control, alloy design, advanced characterization, high-fidelity computational modeling, and machine learning aimed at achieving exceptional mechanical properties in additively manufactured metals.

Additive Manufacturing↗
DOE OSTI2026

Achieving high tensile strength and ductility in refractory alloys by tuning electronic structure

The energy efficiency of heat engines (gas and steam turbines) for electricity production and propulsion is determined by the Carnot cycle and scales with operating temperature. Commercial nickel- and cobalt-based superalloys melt near 1,500 °C and rapidly lose mechanical strength beyond 1,000 °C. Refractory metals melt well above 2,000 °C but have inherent manufacturability challenges that are barriers to adoption, such as high ductile-to-brittle transition temperatures. Using density functional theory-guided design, we demonstrate tailored local lattice distortions that promote phase-stable, non-equiatomic refractory concentrated solid solutions with both high ductility and strength. Here, we exemplify this for single-phase, body-centred cubic Nb 4 Ta 4 V 3 Ti that exhibits castability, excellent room-temperature tensile yield strength (∼1 GPa) and ductility (approaching 20% uniform strain), and exceptional high-temperature tensile strength (500 MPa at 1,000 °C). These findings illustrate a path for designing materials that hold great potential for advancing next-generation technologies such as Generation IV fission reactors, first-generation fusion-plasma reactors, and more efficient gas turbines for electricity generation and propulsion.

DFT↗
DOE OSTI2025

Electrified vapour deposition at ultrahigh temperature and atmospheric pressure for nanomaterials synthesis

Vapour-phase synthesis methods have shown promise for the scalable synthesis of nanomaterials and coatings. However, the vaporization of different precursors for the synthesis of a broad nanomaterial space, particularly at atmospheric pressure, while maintaining compositional and structural control of the final product is challenging. Here we report the generation of an ultrahigh-temperature atomic vapour at atmospheric pressure based on electrified heating, for the growth of multi-elemental nanomaterials and thin films. This process relies on a reactor design whereby solid-state precursors are vaporized within a semi-confined space beneath an electrified heater that can reach ~3,000 K. The proximity of the heater rapidly breaks down the bonds of metal salt precursors and decomposes them into an atomic vapour that expands into a high-temperature (>2,000 K), highly reactive and high-flux vapour (10 21 –10 22 atoms per cm 2 per second) that travels upwards in a directional flow. When mixed with entrained ambient gases, the highly reactive atomic species rapidly nucleate and grow into the desired final products, including alloys, oxides, sulfides and thin films, which can be deposited on a low-temperature substrate. This EVD approach can synthesize a broad range of functional nanomaterials at atmospheric pressure, including single-phase multi-elemental nanomaterials formed under thermodynamically non-equilibrium conditions.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Ab initio prediction of FeCr sigma (001)/FCC Fe(111) interfacial energy: Effect of interfacial doping of C, B, and N

Interfacial energy plays a crucial role for high-temperature material systems in determining their microstructure evolution and mechanical properties. Optimizing the interfacial energy through doping can improve the stability, performance, and overall functionality of these materials. Here, the present study delivers theoretical investigation on the sigma FeCr (001)//FCC Fe (111) interfacial energy using ab initio methods, focusing on the implications of interfacial doping with important interstitial elements carbon (C), boron (B), and nitrogen (N). The calculated interfacial energy without doping is 0.183J/m 2 . Upon doping, notable reductions in interfacial energy were observed. Doping with B decreased the interfacial energy to 0.046J/m 2 , with single C doping to 0.126J/m 2 , with two C doping to 0.098J/m 2 , and with a single N doping to 0.071J/m 2 . These findings not only shed light on the atomistic origin for the effect of stabilizing the microstructure of stainless steel at elevated temperatures by interstitial doping, but also present a systematic, thorough ab initio approach to predict interfacial doping properties and guide alloy design to enhance the performance and stability.

FeCr sigma phase↗
DOE OSTI2025

Oxygen Reduction on Platinum-Nickel and Platinum-Cobalt Alloy Based Catalysts for High Temperature Proton Exchange Membrane Fuel Cells

Catalyst layers, with commercial PtNi/TKK (TECNiE52; platinum 46.5 wt%), PtCo/TKK (TEC36E52; platinum 45.8 wt%) catalysts, and an in-house catalyst PtNi-NC (platinum 38.4 wt%), synthesised using acoustic mixer and a tube furnace, are prepared using three different ionomers: 20 wt% Nafion®, 60 wt% polytetrafluoroethylene (PTFE), and an in-house 5 wt% ionomer (‘Ionomer X’). These inks are bar-coated onto carbon paper gas diffusion layers (GDLs), which are cut into 3 cm × 5 cm pieces. The coated layers are tested for oxygen reduction in a commercial gas diffusion electrode (GDE) test cell, FlexCell® (Gaskatel GmbH, Germany), using 85 wt% phosphoric acid at both room temperature and at 155°C. This study evaluates the polynorbornene (PNB)-based in-house ionomer performance as binder and in-house catalyst oxygen reduction reaction (ORR) activity in comparison to commercial products. The catalyst layers are characterised using X-ray diffraction (XRD) analysis, X-ray photoelectron spectroscopy (XPS), and high-angle annular dark-field scanning transmission electron microscopy (HAADF-STEM). Among the catalyst layers prepared with PTFE ionomer and tested at 155°C, the in-house catalyst demonstrates the highest ORR activity. Ionomer X proves to be a good candidate to be used as a per- and polyfluoroalkyl-free binder for high-temperature (HT) proton exchange membrane fuel cell (PEMFC) applications.

85 wt% phosphoric acid↗
DOE OSTI2024

Metal-to-Ceramic Joining Methods to Support Development of Advanced Ceramic-Based CSP Components

The National Renewable Energy Laboratory, Missouri University of Science and Technology (MS&T), Massachusetts Institute of Technology (MIT), and Colorado School of Mines (CSM) collaborated to design, develop, and test a material concept at bench scale which will be used to achieve a ceramic-to-metal (C2M) joint between a selected metal HTF loop material and a selected ceramic material used by the Gen3 CSP technology pathway. The final joint assembly will need to possess sufficient mechanical properties to withstand static high-temperature (650 degrees-700 degrees C) and high-pressure (20 MPa) and thermal cycling (between 650 degrees C and 100 degrees C) conditions. The material concept consists of three key components: (1) a ceramic matrix composite (CMC) that serves as a compliant transition material aiming to mitigate the stresses due to the mismatch of coefficient of thermal expansion (CTE) from a direct ceramic-to-metal joint, (2) a metal-end joint utilizing a multi-principal element alloy (MPEA) with changing percentage of particle loading to bond the candidate metal to the CMC, and (3) a ceramic-end joint utilizing a glass ceramic to bond the candidate ceramic to the CMC.

14 SOLAR ENERGY↗
DOE OSTI2024

High-Temperature Oxidation Behavior of Wrought and Additive Manufactured H282 in Direct-Fired Supercritical CO2 Power Cycle Environments

Materials selection is a key concern for corrosion resistance in high temperature and pressure direct-fired supercritical CO2 power cycles. The effect of elevated pressure on corrosion resistance can be critical, as impurities within the supercritical fluid such as H2O and O2 can result in additional corrosion behaviors. Utilizing additive manufacturing (AM) methods for construction of power cycle components requiring both compact and complex designs could be advantageous. AM H282 produced by laser powder bed fusion was exposed to direct-fired conditions (95CO2 – 4H2O – 1 O2) at 750 °C at both atmospheric pressure and supercritical conditions (20 MPa) for up to 4,000 hours. Oxidation behavior, sub-surface carbide formation, and chromia scale volatilization was dependent upon AM preparation techniques and surface modifications. These results are discussed in terms of the potential compatibility issues that may arise when using AM alloys in high temperature regions of direct-fired sCO2 power cycles, particularly for thin-walled components.

Carney, Casey↗
DOE OSTI2024

Evaluating Microchannel Heat Exchanger Lifetime for Concentrating Solar Power Applications FY24Q4 (RPPR-1)

Microchannel heat exchanger technology is being pursued for next generation CSP concepts for primary power cycle heat addition and power cycle heat recuperation due to the high heat transfer coefficients and pressure containment advantages of small sCO 2 channels. The economics of future CSP plants as dictated by the SETO 2020 or 2030 targets depend on a heat exchanger with a 30-year lifetime (resisting creep, fatigue, corrosion, erosion) and operational characteristics such as fast ramping and the ability to withstand thermal shock. However, the lifetime and operational limits of microchannel heat exchangers operating at high-temperatures, particularly those constructed from high-nickel alloys, are not well known. This uncertainty has resulted in heat exchanger vendors not being able to accurately forecast heat exchanger lifetime as required by customers, specify operational limits as required by process engineers to prevent premature heat exchanger failure, or overdesign heat exchanger which leads to higher cost than necessary. Our goal is to evaluate heat exchanger lifetime and operational limits for the manufacturing and prototype design for next-generation CSP heat exchanger technology through a combination of collecting experimental data and modeling studies.

14 SOLAR ENERGY↗
DOE OSTI2024

Environmental Compatibility Issues for Ni-Based Alloys in Direct-Fired Supercritical CO2 Power Cycles

Direct-fired supercritical CO2 (sCO2) power cycles offer potential for high-efficiency power generation from natural gas and other fossil fuels with built-in carbon capture. Ni-based superalloys are the leading candidates for the hottest portions of these systems, where they must endure long-term exposure to high-temperature, high-pressure, high-velocity, impure CO2-rich environments. Herein we describe results of various experimental testing campaigns conduced at NETL showing that under such conditions, several simultaneously occurring degradation modes may be active including surface oxidation, alloy carburization, and oxide volatilization. It will be shown that the rates of degradation can be strongly affected by the alloy composition, impurities in the CO2, manufacturing method (wrought vs additive), and other factors. The influence of these factors in controlling alloy degradation are discussed in the context of potential compatibility issues for components in real sCO2 systems, such as compact heat exchangers. Finally, as a potential remedial measure, ongoing work involving protective coatings suitable for complex geometries is presented.

alloy oxidation↗
DOE OSTI2024

Microstructure Optimization and Novel Processing Development of ODS Steels for Fusion Environments (Final ARPA-E Report)

This project aimed to develop scalable, cost-effective fabrication of high-performance, oxide- dispersion-strengthened (ODS) steel using advanced manufacturing methods (AMMs) for fusion blanket-breeding applications. Gas atomization reaction synthesis (GARS) enables the synthesis of precursor ODS steel powders without prolonged mechanical alloying. This process creates a chromium (Cr)-enriched surface oxide with yttrium/titanium (Y/Ti)-enriched intermetallics in powder interiors. GARS powders were consolidated to >99% of the theoretical density using a first-of-a-kind shear assisted processing and extrusion (ShAPE) and laser-based powder bed fusion (L-PBF) AM processes. These processes led to ODS steels containing a high-density of nano-oxide dispersoids that enhance high-temperature mechanical properties. Such scalable, cost-effective fabrication of ODS steels can enable efficient power conversion cycles (=40%) at operating temperatures beyond 900 K in future fusion power plants.

36 MATERIALS SCIENCE↗
DOE OSTI2025

LAROMance Grade 91 Model Integration in NEML2

New reactor designs are targeting higher operating temperatures for increased thermal efficiency when compared to the current fleet of light water reactors. Designing structural components for these high temperature environments with reliable long-term operations requires material models that can accurately capture the deformation mechanisms active in these environments. The LAROMance surrogate material models are based on a database of mechanistic crystal plasticity simulations for high-temperature conditions. Inputs to the LAROMance models reflect the microstructural pedigree of the material, like dislocation densities and precipitate contents. Based on the evolution of these microstructural features, the LAROMance model provides the engineering scale constitutive model response. The LAROMance model was recently parameterized for Grade 91, a high temperature alloy. In the present work, the Grade 91 LAROMance model is implemented in the New Material Model Library, version 2 (NEML2). NEML2 provides a modular way to build material models from smaller blocks and was developed to vectorize the material update to efficiently run on modern computational architectures with graphics processing unit accelerators. NEML2 constitutive models can be used in simulations based on the multiphysics object-oriented simulation environment (MOOSE). This report provides details on the implementation of the Grade 91 LAROMance model in NEML2 and its verification of engineering scale finite element simulations in MOOSE.

42 - ENGINEERING↗
DOE OSTI2025

Manufacturability and performance response of developed Ni-based alloys for reactor environments

Under the Advanced Materials and Manufacturing Technologies program, two Ni-based alloys fabricated by laser powder bed fusion (LPBF) at Oak Ridge National Laboratory and by laser powder directed energy deposition (LP-DED) at Idaho National Laboratory have been evaluated: γ′-strengthened Haynes 282 and solution-strengthened Inconel 625. Printing defects were observed in the LPBF 282 alloy fabricated using a Renishaw AM250 machine, likely due to particle spattering during printing. For both the LPBF and LP-DED 282 alloys, annealing at 1,180°C for 1 h resulted in partial recrystallization and a bimodal grain distribution, and subsequent aging for 4 h at 800°C led to the formation of a high density of nano-size γ′-strengthening precipitates. Creep testing performed at 750°C revealed lower creep life and ductility for the LPBF and LP-DED 282 compared with wrought 282. X-ray computed tomography combined with optical and scanning electron microscopy microstructural characterization revealed crack formation in the LPBF 282 alloy during creep testing, initiated either from printing defects or from creep cavitation at grain boundaries. Creep cavitation and cracking at grain boundaries were also observed for the LP-DED 282 alloy, and optimization of the printing strategies and postheat treatments will be needed to fabricate high-performance 282 components for high-temperature nuclear applications.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Radiation Damage Mitigation in FeCrAl Alloy at Sub-Recrystallization Temperatures

Traditional defect recovery methods rely on high-temperature annealing, often exceeding 750 °C for FeCrAl. In this study, we introduce electron wind force (EWF)-assisted annealing as an alternative approach to mitigate irradiation-induced defects at significantly lower temperatures. FeCrAl samples irradiated with 5 MeV Zr 2+ ions at a dose of 10 14 cm −2 were annealed using EWF at 250 °C for 60 s. We demonstrate a remarkable transformation in the irradiated microstructure, where significant increases in kernel average misorientation (KAM) and low-angle grain boundaries (LAGBs) typically indicate heightened defect density; the use of EWF annealing reversed these effects. X-ray diffraction (XRD) confirmed these findings, showing substantial reductions in full width at half maximum (FWHM) values and a realignment of peak positions toward their original states, indicative of stress and defect recovery. To compare the effectiveness of EWF, we also conducted traditional thermal annealing at 250 °C for 7 h, which proved less effective in defect recovery as evidenced by less pronounced improvements in XRD FWHM values.

FeCrAl alloys↗
DOE OSTI2024

Microstructural and Oxidation Effects of Nb Additions to U3Si2

U3Si2 is a long term, accident-tolerant nuclear fuel candidate for light-water reactors because of its superior thermal conductivity and increased uranium density when compared to traditional uranium dioxide (UO2). While reducing internal thermal stresses and increasing efficiency, U3Si2 exhibits energetic oxidation during certain off-normal and accident scenarios, which include coolant or steam exposure. To mitigate this, Nb is investigated as an alloy constituent to enhance corrosion resistance and increase mechanical strength. The work presented investigates the response of Nb-alloyed U3Si2 to steam atmospheres. A thermogravimetric analysis is conducted in flowing steam to T > 1000 °C to assess oxidation resistance. The phase characterization of as-melted, thermally annealed and post-oxidation compositions with up to 12 vol% Nb by powder X-ray diffraction, scanning electron microscopy, and energy dispersive spectroscopy is reported.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗