Search NASA⌕ Search

SEARCH · Search NASA

Results for “Homojunction”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Breakdown characteristics analysis of kV-class vertical GaN PIN rectifiers by wafer-level sub-bandgap photoluminescence mapping

This work reports analysis of the reverse-bias breakdown characteristics of homojunction gallium nitride (GaN) p–i–n (PIN) rectifiers fabricated on bulk GaN substrates. Sub-bandgap photoluminescence mapping at room temperature as a contactless, non-destructive wafer inspection method was performed to analyze the impact of material properties on grown GaN PIN diodes and to study the correlation between defect types and breakdown characteristics of vertical GaN PIN rectifiers. Under the sub-bandgap excitation, yellow luminescence is dominant. The premature breakdown characteristics of the fabricated kV-class vertical GaN PIN rectifiers with nitrogen-implanted floating guard rings are found to be associated with material defects and deep level complexes. Photoluminescence mapping has demonstrated its effectiveness in quantitative analysis of dislocations and other types of defects.

42 ENGINEERING↗

All-MOCVD-grown gallium nitride diodes with ultra-low resistance tunnel junctions

In this work, we carefully investigate three important effects including postgrowth activation annealing, delta (δ) dose and magnesium (Mg) buildup delay as well as experimentally demonstrate their influence on the electrical properties of GaN homojunction p–n diodes with a tunnel junction (TJ). The diodes were monolithically grown by metalorganic chemical vapor deposition (MOCVD) in a single growth step. By optimizing the annealing parameters for Mg activation, δ-dose for both donors and acceptors at TJ interfaces, and p + -GaN layer thickness, a significant improvement in tunneling properties is achieved. For the TJs embedded within the continuously-grown, all-MOCVD GaN diode structures, ultra-low voltage penalties of 158 mV and 490 mV are obtained at current densities of 20 A cm –2 and 100 A cm –2 , respectively. The diodes with the engineered TJs show a record-low differential resistivity of 1.6 × 10 –4 Ω cm 2 at 5 kA cm –2 .

42 ENGINEERING↗

Development of GaInP Solar Cells Grown by Hydride Vapor Phase Epitaxy

We demonstrate the growth of homojunction GaInP solar cells by dynamic hydride vapor phase epitaxy for the first time. Simple unpassivated n-on-p structures grown in an inverted configuration with gold back reflectors were analyzed. Short wavelength performance varied strongly with emitter thickness, since collection in the emitter was limited by the lack of surface passivation. Collection in the base increased strongly with decreasing doping density, in the range 1 x 10 16 - 5 x 10 17 cm -3 . Optical modeling indicated that, in our best device, doped ~1 x 10 16 cm -3 , almost 94% of photons that passed through the emitter were collected. Modeling also indicated that the majority of collection occurs in the depletion region with this design, suggesting that nonradiative recombination there might limit device performance. In agreement with this observation, the experimental dark J-V curve exhibited an ideality factor near n = 2. Thus, limitation of deep level carrier traps in the material is a path to improved performance. Preliminary experiments indicate that a reduced V/III ratio, which potentially affects the density of these presumed traps, improves cell performance. With reduced V/III ratio, we demonstrate a ~13% efficient GaInP cell measured under the 1-sun AM1.5G spectrum. In conclusion, this cell had an antireflective coating, but no front surface passivation.

14 SOLAR ENERGY↗

Effect of Window-Layer Materials on p-n Junction Location in Cu(In,Ga)Se 2 Solar Cells

We report on measurements of junction location in Cu(In,Ga)Se $_{2}$ (CIGS) solar cells with different window-layer materials by nm-resolution electrical potential/field profiling across the junction using Kelvin probe force microscopy imaging on cross-section of the devices. The results illustrate that the device with a CdS window layer (CdS/CIGS) has a buried homojunction located inside the CIGS absorber with ~40-nm junction depth, whereas the ZnOS/CIGS devices with and without partial electrolyte treatment prior to the window-layer deposition are similar, exhibiting a heterointerface junction. This junction location may contribute in part to the highest efficiency of the CdS/CIGS device among the three devices.

14 SOLAR ENERGY↗

Reverse Heterojunction (Al)GaInP Solar Cells for Improved Efficiency at Concentration

Mitigating series resistance is crucial to the efficiency of concentrator solar cells at high current density. Conventional AlGaInP junction designs for the top junction of III-V multijunction cells present a challenging tradeoff between series resistance on the one hand and current collection and voltage on the other hand. In this article we discuss the physics of a reverse heterojunction solar cell that aims to improve on this tradeoff by combining a high bandgap Al 0.18 Ga 0.33 In 0.49 P base and a lower bandgap (Al)GaInP emitter. The high mobility of the emitter leads to a relatively low series resistance, compared with a high bandgap homojunction cell. Furthermore, the electroluminescence spectrum shows emission peaks from both the emitter and base, leading to an open-circuit voltage that is not strictly dominated by either layer. The reverse heterojunction design is increasingly beneficial as the one-sun voltage increases.

14 SOLAR ENERGY↗

15.3% AM1.5G Efficiency GaAs Solar Cells Fabricated via an Epitaxy-Free Process

Here, we report simple and potentially low-cost techniques for creating high-quality n-type gallium arsenide (GaAs) and GaAs p/n junctions and fabricate GaAs p/n junction solar cells. Detailed-balance modeling suggests that 20% AM1.5G efficiency p/n homojunction devices may be possible if the surface doping concentration can be limited to values less than ∼ 5 × 10 19 cm −3 . Our process exploits an open-tube, vapor-phase, deposition-free, zinc diffusion technique for forming p-type layers in melt-grown n-GaAs substrates that results in sheet resistances less than 1 kΩ/$\square$. In addition, we have improved the minority carrier diffusion lengths of melt-grown GaAs from less than one micron to over five microns using an open-tube, vacuum-free, annealing process which reduces the density of EL2 midgap defects. Finally, we have combined these advances to fabricate epitaxy-free, GaAs solar cells with a validated AM1.5G efficiency of 15.3%.

14 SOLAR ENERGY↗

Imaging the Solar Cell P-N Junction and Depletion Region Using Secondary Electron Contrast

We report on secondary electron (SE) images of cross-sectioned multicrystalline Si and GaAs/GaInP solar cell devices, focusing on quantifying the relationship between the apparent n{sup +}-p contrast and characteristic electronic features of the device. These samples allow us to compare the SE signal from devices which have very different physical characteristics: differing materials, diffused junction versus abrupt junction, heterojunction versus homojunction. Despite these differences, we find that the SE image contrast for both types of sample, and as a function of reverse bias across the diode, closely agrees with PC1D simulations of the bulk electrostatic potential in the device, accurately yielding the depletion edge and width. A spatial derivative of the SE data shows a local maximum at the metallurgical junction. Such data are valuable, for example, in studying the conformity of a diffused junction to the textured surface topography. These data also extend our understanding of the origin of the SE contrast.

14 SOLAR ENERGY↗

Nanoscale Measurements of the Surface Photovoltage in Cu(In,Ga)Se2, Cu2ZnSnS4, and Cu2ZnSnSe4 Thin Films: The Role of the Surface Electronics on the Efficiency of Solar Cells

We report on recent advances in the development of nanoscale measurements of the surface photovoltage (SPV) based on scanning tunneling microscopy (STM) and its application to the kesterites Cu{sub 2}ZnSnS{sub 4} (CZTS) and Cu{sub 2}ZnSnSe{sub 4} (CZTSe). One critical aspect of the electronic structure of Cu(In, Ga)Se{sub 2} (CIGS) that has yet to be determined in their related kesterite compounds is the character of the surface electronics. In CIGS, spontaneous deviations in the stoichiometry of the surface cause a depletion (or even a type inversion) region that reinforces the CIGS homojunction. First-principle calculations predict that this inversion region will be more difficult to form in CZTS. In this contribution, the characteristics of the surface space charge region for both CIGS and CZTS(e) are investigated by STM. The implications of the results of these measurements on the future development of CZTS solar cells will be discussed.

14 SOLAR ENERGY↗

Determination of the Electrical Junction in Cu(In, Ga)Se2 and Cu2ZnSnSe4 Solar Cells with 20-nm Spatial Resolution

We located the electrical junction (EJ) of Cu(In, Ga)Se2 (CIGS) and Cu2ZnSnSe4 (CZTS) solar cells with ~20-nm accuracy using a scanning capacitance spectroscopy (SCS) technique. A procedure was developed to prepare the cross-sectional samples and grow critical high-quality insulating layers for the SCS measurement. We found that CIGS has a buried homojunction with the EJ located at ~40 nm inside the CIGS/CdS interface. An n-type CIGS was probed in the region 10-30 nm away from the interface. By contrast, the CZTS/CdS cells have a heterointerface junction with a shallower EJ (~20 nm) than CIGS. The EJ is ~20 nm from the CZTS/CdS interface, which is consistent with asymmetrical carrier concentrations of the p-CZTS and n-CdS in a heterojunction cell. The unambiguous determination of the junction locations helped explain the large open circuit voltage difference between the state-of-the-art devices of CIGS and CZTS.

14 SOLAR ENERGY↗

GaLnAsP Solar Cells Grown by Hydride Vapor Phase Epitaxy for One-Sun & Low-Concentration III-V/Si Photovoltaics

Dynamic hydride vapor phase epitaxy (D-HVPE) has recently reemerged as a low-cost alternative to metalorganic chemical vapor deposition (MOCVD) for the growth of highefficiency III-V solar cells. Quaternary GaInAsP solar cells in the bandgap range of ~1.6-1.8 eV are promising top-cell candidates for III-V/Si tandem solar cells. In this work, we report on the development of lattice-matched GaInAsP (Eg~1.66 eV) solar cells grown via low-cost HVPE at very high growth rates of ~0.7 um/min (~42 um/h). We demonstrate for the first time HVPE grown passivated GaInAsP homojunction solar cells that show substantial improvement in the short-wavelength photoresponse attributed to the incorporation of a GaInP window layer. The heterointerfaces in these multilayer devices were characterized by transmission electron microscopy. The best device achieved a certified one-sun efficiency of 18.7% under AM1.5G, demonstrating the viability of HVPE to grow multilayered structures comprising ternary and quaternary alloys. This work represents a promising step towards low-cost III-V/Si tandem photovoltaics with one-sun efficiencies exceeding 30%.

14 SOLAR ENERGY↗

Metal Induced Recombination Parameter Extraction using High Resolution Photoluminescence Imaging for Silicon Solar Cells

Metal induced recombination (i.e., contact recombination) is a significant loss mechanism for homojunction crystalline silicon solar cells. In this work, a method is proposed to extract the metal induced recombination parameters using highresolution photoluminescence PL imaging. By calculating the voltage distribution profile between fingers, the total current flow from the semiconductor to the finger, per area, can be obtained. The total recombination current at the semiconductor area and the metal contact area are then calculated and used to calculate the reverse saturation current for each region. The metal induced reverse saturation current (j 0m ) is then obtained. This measurement allows the extraction of j 0m on finished solar cells without the need to make special metal test structures. This is a big advantage over existing methods.

14 SOLAR ENERGY↗

1.2-kV Vertical GaN PIN Rectifier With Ion-Implanted Floating Guard Rings

Here, this work reports on the fabrication and properties of a homojunction gallium nitride (GaN) p-i-n (PIN) rectifier fabricated on a free-standing GaN substrate. Uniform device performance is achieved with breakdown voltage (BV) >1.2 kV and low ON-resistance × area ( R ON A ). The statistics of the BV measurements show 58.5% of devices achieve BV >1.3 kV, and 71.1% of devices achieve BV >1.2 kV, as attributed to high quality and control in both epitaxial growth and device process. At room temperature, R ON A is 0.23 mΩ∙ cm 2 at a current density ( J ) of 6.9 kA/cm2. The corresponding Baliga’s figure of merit is >5.97 GW/cm 2 . Temperature-dependent reverse I – V measurements were performed and show a positive temperature coefficient of 0.42 V/K, indicating the avalanche capability of reverse breakdown. Further analysis with the Poole-Frenkel model on the temperature-dependent measurement suggested that a trap-assisted tunneling process contributed to the reverse leakage current. Floating guard rings (FGRs) formed by nitrogen implantation serve as an effective edge termination technique in these GaN PIN rectifiers, resulting in uniform performance in both forward and reverse bias.

42 ENGINEERING↗

Si/TiO 2 Tandem-Junction Microwire Arrays for Unassisted Solar-Driven Water Splitting

In this work, tandem-junction microwire array photoelectrodes have been fabricated by coating np + -Si radial homojunction microwire arrays sequentially with fluorine-doped tin oxide (FTO) and titanium dioxide (TiO 2 ). These photoelectrodes effected unassisted water splitting under simulated 1 Sun conditions with an open-circuit potential ($E_{\text{oc}}$) of –1.5 V vs the formal potential for oxygen evolution, $E^0$'(OH – /O 2 ), a current density at $E = E^0$'(OH – /O 2 ) of 0.78 mA cm –2 , a fill factor ($\textit{ff}$) = 0.51, and a photovoltaic-biased photoelectrochemical ideal regenerative cell efficiency of 0.6%.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Analysis of the Junction Properties of CdS/CdTe Devices in Substrate and Superstrate Configurations

The best efficiency of CdS/CdTe devices fabricated in the substrate configuration reported to date is about 8%, which is about half the 17.3% reported for the conventional superstrate configuration. The performance of substrate devices is affected by lower open-circuit voltage (Voc), about 700 mV, and low fill factor (FF), which indicates that these devices are primarily limited by non-idealjunction properties and possibly by the ohmic contact to CdTe. In our study of the junction properties of superstrate devices, we show that lower-Voc devices (< 720 mV) with SnO2/CdTe and CdS/CdTe structures are true heterojunction devices. High charged defect density at the heterointerfaces is present in the depletion region and contributes to the dark current density, thereby reducingVoc. On the other hand, for higher-performance devices with Voc > 800 mV, the junction is between an n-type, Te-rich CdSTe alloy with a bandgap of 1.45 eV and p-type CdTe with a bandgap of 1.5 eV. Because the crystal structure of both the Te-rich alloy and the CdTe is cubic zinc blende, and the lattice mismatch between the two is minimal, the device in this case can be considered aquasi-homojunction. These higher-Voc devices are therefore affected less by the high charged defect density at the hetero-interface, which lies outside of the depletion region. We present analysis of the junction properties of our recent and improved substrate-configuration devices with Voc well in excess of 800 mV, FF approaching 60%, and efficiencies around 10%. We also compare devicesfabricated in both the substrate and superstrate configurations and with comparable Voc in the range of 700 to more than 800 mV. Photoluminescence (PL) and temperature-dependent PL, current density-voltage and quantum efficiency analysis, and modulated reflectance measurements are used to study device properties.

14 SOLAR ENERGY↗

Economical fabrication process produces high quality junction transistors

A convenient, three-step fabrication process, with a p-type layer of gallium arsenide vapor deposited on a starting wafer of germanium, is used to produce heterojunction-homojunction p-n-p transistors. These are of high quality with good injection efficiency and low capacitance.

Source record↗

A study of the electrical properties of p-n junctions formed by ion-implantation into gallium arsenide

In the process of ion implantation, ion beams bombard the surface and create undesirable surface effects. The surface effects were investigated, and surface leakage currents were shown to be reduced by surface treatment. I-V characteristics and C-V measurements were obtained for the Zn-GaAs and Zn-(In,Ga)As junction is considered as a p-i-n heterojunction, without generation-recombination current. The Zn-GaAs junction is considered as a p-n homojunction with appreciable generation-recombination currents.

Lin, A. H.↗