Search NASA⌕ Search

SEARCH · Search NASA

Results for “ID”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1994

An improved plating process

An alternative to the immersion process for the electrodeposition of chromium from aqueous solutions on the inside diameter (ID) of long tubes is described. The Vessel Plating Process eliminates the need for deep processing tanks, large volumes of solutions, and associated safety and environmental concerns. Vessel Plating allows the process to be monitored and controlled by computer thus increasing reliability, flexibility and quality. Elimination of the trivalent chromium accumulation normally associated with ID plating is intrinsic to the Vessel Plating Process. The construction and operation of a prototype Vessel Plating Facility with emphasis on materials of construction, engineered and operational safety and a unique system for rinse water recovery are described.

Askew, John C.↗
NASA NTRS1997

Bidirectional Brush Seals: Post-Test Analysis

A post-test analysis of a set of inside-diameter/outside-diameter (ID/OD) bidirectional brush seals used in three-port wave rotor tests was undertaken to determine brush bristle and configuration wear, pullout, and rotor coating wear. The results suggest that sharp changes in the pressure profiles were not well reflected in bristle tip configuration patterns or wear. Also, positive-to-negative changes in axial pressure gradients appeared to have little effect on the backing plates. Although the brushes had similar porosities, they had very different unpacked arrays. This difference could explain the departure of experimental data from computational fluid dynamics flow predictions for well-packed arrays at higher pressure drops. The rotor wear led to "car-track" scars (upper and lower wear bands) with a whipped surface between the bands. Those bands may have resulted from bristle stiffening at the fence and gap plates during alternate portions of the rotor cycle. Within the bristle response range the wear surface reflected the pressure distribution effect on bristle motion. No sacrificial metallurgical data were taken. The bristles did wear, with correspondingly more wear on the ID brush configurations than on the OD configurations; the complexity in constructing the ID brush was a factor.

Hendricks, Robert C.↗
NASA NTRS1998

Integrated Display System for Low Visibility Landing and Surface Operations

This report summarizes the software products and system architectures developed by Lockheed Martin in support of the Low Visibility Landing and Surface Operations (LVLASO) program at NASA Langley Research Center. It presents an overview of the technical aspects, capabilities, and system integration issues associated with an integrated display system (IDS) that collects, processes and presents information to an aircraft flight crew during all phases of landing, roll-out, turn-off, inbound taxi, outbound taxi and takeoff. Communications hardware, drivers, and software provide continuous real-time data at varying rates and from many different sources to the display programs for presentation on a head-down display (HDD) and/or a head-up display (HUD). An electronic moving map of the airport surface is implemented on the HDD which includes the taxi route assigned by air traffic control, a text messaging system, and surface traffic and runway status information. Typical HUD symbology for navigation and control of the aircraft is augmented to provide aircraft deceleration guidance after touchdown to a pilot selected exit and taxi guidance along the route assigned by ATC. HUD displays include scene-linked symbolic runways, runway exits and taxiways that are conformal with the actual locations on the airport surface. Display formats, system architectures, and the various IDS programs are discussed.

Beskenis, Sharon Otero↗
NASA NTRS1999

Using the World Wide Web for GIDEP Problem Data Processing at Marshall Space Flight Center

Since April 1997, Marshall Space Flight Center has been using electronic transfer and the web to support our processing of the Government-Industry Data Exchange Program (GIDEP) and NASA ALERT information. Specific aspects include: (1) Extraction of ASCII text information from GIDEP for loading into Word documents for e-mail to ALERT actionees; (2) Downloading of GIDEP form image formats in Adobe Acrobat (.pdf) for internal storage display on the MSFC ALERT web page; (3) Linkage of stored GRDEP problem forms with summary information for access from the MSFC ALERT Distribution Summary Chart or from an html table of released MSFC ALERTs (4) Archival of historic ALERTs for reference by GIDEP ID, MSFC ID, or MSFC release date; (5) On-line tracking of ALERT response status using a Microsoft Access database and the web (6) On-line response to ALERTs from MSFC actionees through interactive web forms. The technique, benefits, effort, coordination, and lessons learned for each aspect are covered herein.

McPherson, John W.↗
NASA NTRS1997

Optical Verification Laboratory Demonstration System for High Security Identification Cards

Document fraud including unauthorized duplication of identification cards and credit cards is a serious problem facing the government, banks, businesses, and consumers. In addition, counterfeit products such as computer chips, and compact discs, are arriving on our shores in great numbers. With the rapid advances in computers, CCD technology, image processing hardware and software, printers, scanners, and copiers, it is becoming increasingly easy to reproduce pictures, logos, symbols, paper currency, or patterns. These problems have stimulated an interest in research, development and publications in security technology. Some ID cards, credit cards and passports currently use holograms as a security measure to thwart copying. The holograms are inspected by the human eye. In theory, the hologram cannot be reproduced by an unauthorized person using commercially-available optical components; in practice, however, technology has advanced to the point where the holographic image can be acquired from a credit card-photographed or captured with by a CCD camera-and a new hologram synthesized using commercially-available optical components or hologram-producing equipment. Therefore, a pattern that can be read by a conventional light source and a CCD camera can be reproduced. An optical security and anti-copying device that provides significant security improvements over existing security technology was demonstrated. The system can be applied for security verification of credit cards, passports, and other IDs so that they cannot easily be reproduced. We have used a new scheme of complex phase/amplitude patterns that cannot be seen and cannot be copied by an intensity-sensitive detector such as a CCD camera. A random phase mask is bonded to a primary identification pattern which could also be phase encoded. The pattern could be a fingerprint, a picture of a face, or a signature. The proposed optical processing device is designed to identify both the random phase mask and the primary pattern [1-3]. We have demonstrated experimentally an optical processor for security verification of objects, products, and persons. This demonstration is very important to encourage industries to consider the proposed system for research and development.

Javidi, Bahram↗
NASA NTRS1996

Improving Conceptual Design for Launch Vehicles

This report summarizes activities performed during the second year of a three year cooperative agreement between NASA - Langley Research Center and Georgia Tech. Year 1 of the project resulted in the creation of a new Cost and Business Assessment Model (CABAM) for estimating the economic performance of advanced reusable launch vehicles including non-recurring costs, recurring costs, and revenue. The current year (second year) activities were focused on the evaluation of automated, collaborative design frameworks (computation architectures or computational frameworks) for automating the design process in advanced space vehicle design. Consistent with NASA's new thrust area in developing and understanding Intelligent Synthesis Environments (ISE), the goals of this year's research efforts were to develop and apply computer integration techniques and near-term computational frameworks for conducting advanced space vehicle design. NASA - Langley (VAB) has taken a lead role in developing a web-based computing architectures within which the designer can interact with disciplinary analysis tools through a flexible web interface. The advantages of this approach are, 1) flexible access to the designer interface through a simple web browser (e.g. Netscape Navigator), 2) ability to include existing 'legacy' codes, and 3) ability to include distributed analysis tools running on remote computers. To date, VAB's internal emphasis has been on developing this test system for the planetary entry mission under the joint Integrated Design System (IDS) program with NASA - Ames and JPL. Georgia Tech's complementary goals this year were to: 1) Examine an alternate 'custom' computational architecture for the three-discipline IDS planetary entry problem to assess the advantages and disadvantages relative to the web-based approach.and 2) Develop and examine a web-based interface and framework for a typical launch vehicle design problem.

John R. Olds↗
NASA NTRS1999

RXTE Observation of 4U 1630-47 During its 1998 Outburst

During the 1998 outburst of 4U 1630-47 it was extensively observed with the Rossi X-ray Timing Explorer (RXTE). In order to cover the outburst more thoroughly our data (Obs. ID: 30178-0[1-2]- ) were combined with those of Cui et al. (Obs. ID: 30188-02-). These observations were later compared with the complementary observations. Power density and energy spectra have been made for each observation. The data was used to place radio and hard X-ray observations within context. Analysis of SAX (Satellite per Astronomia a raggi X) and BATSE (Burst and Transient Source Experiment) data was also included within the study. The count rate and position in hardness-intensity, color-color diagrams and simple spectral fits are used to track the concurrent spectral changes. The source showed seven distinct types of timing behavior, most of which show differences with the canonical black hole spectral/timing states. In marked contrast to previous outbursts, we find quasi-periodic oscillation (QPO) signals during nearly all stages of the outburst with frequencies between 0.06 Hz and 14 Hz and a remarkable variety of other characteristics. In particular we find large (up to 23% rms) amplitude QPO on the early rise. Later, slow 0.1 Hz semi- regular short (- 5 sec), 9 to 16% deep dips dominate the light curve. At this time there are two QPOS, one stable near 13.5 Hz and the other whose frequency drops from 6-8 Hz to - 4.5 Hz during the dips. BeppoSAX observations during the very late declining phase show 4U 1630-47 in a low state. These results will shortly be published. We are completing a detailed analysis of the energy spectra (in preparation). The QPO/noise properties are being correlated with the concurrent spectral changes. Detailed studies of the QPO are being undertaken using sophisticated timing analysis methods. Finally a comparison with the other outbursts of 1630-47 is being made.

Dieters, Stefan W.↗
NASA NTRS1991

Rollout of Endeavour at Palmdale, California (Part 1 of 2)

Footage shows the rollout ceremonies for Endeavour, including the display of colors, invocation, and speeches by Sam Iacobellis, Executive Vice-President and CEO of Rockwell International, Richard H. Truly, Administrator for NASA, and Senator Jake Garn (Utah). The tape ends during the speech by Senator Garn and continues on part two (Input Processing ID 2000152220, Document ID 20010010951). Endeavour rolls out to music provided by the band on-site.

Source record↗
NASA NTRS1991

Rollout of Endeavour at Palmdale, California (Part 2 of 2)

A continuation of the video 'Rollout of Endeavour at Palmdale, California (Part 1 of 2)' (Input Processing ID 2000152226, Document ID 20010010950), Senator Jake Garn (Utah) concludes his speech during the rollout ceremonies for the Endeavour Orbiter. Congressman Tom Lewis (Florida) and Dr. Robert Duce of the University of Rhode Island also give speeches. Commander Daniel C. Brandenstein introduces the crew of STS-49, Pilot Kevin P. Chilton, and Mission Specialists Pierre J. Thuot, Kathryn C. Thornton, Richard J. Hieb, Thomas D. Akers, and Bruce E. Melnick, and gives an overview of the Endeavour Orbiter and the mission objectives.

Source record↗
NASA NTRS2001

STS-97 Mission Highlights Resource Tape

Various clips give an overview of the STS-97 Endeavour mission. Footage includes Endeavour on the launch pad, the crew of STS-97 (Commander Brent W. Jett, Pilot Michael J. Bloomfield, and Mission Specialists Joseph R. Tanner, Carlos I. Noriega, and Marc Garneau) suiting up, replays of the nighttime launch, Launch Control Center at Kenendy Space Center during countdown, and the activities of flight days one through three. The activities of flight days four through six can be seen on 'STS-97 Mission Highlights Resource Tape, Part 2 of 3' (document ID 20010020282). The activities of flight days seven through eleven and Endeavour's landing can be found on 'STS-97 Mission Highlights Resource Tape, Part 3 of 3' (document ID 20010020283).

Source record↗
NASA NTRS2001

STS-97 Mission Highlights Resource Tape

A continuation of 'STS-97 Mission Highlights Resource Tape, Part 1 of 3' (document ID 20010020281), the activities of flight days four through six are seen. Footage includes the spacewalks performed by Noriega and Tanner, the deployment of the Solar Array Blanket Box (SABB), various shots of Endeavour's payload bay and the International Space Station (ISS), and the deployment of the solar radiators on the ISS. Flight days seven through eleven and Endeavour's landing are shown in 'STS-97 Mission Highlights Resource Tape, Part 3 of 3' (document ID 20010020283).

Source record↗
NASA NTRS2001

STS-97 Mission Highlights Resource Tape

A continuation of 'STS-97 Mission Highlights Resource Tape, Part 1 of 3' (document ID 20010020281) and 'STS-97 Mission Highlights Resource Tape, Part 2 of 3' (document ID 20010020282), the activities of flight days seven through eleven are seen. Footage includes the crew discussing repair procedures for the Solar Array Wing (SAW) with mission managers, shots of the shuttle's payload bay, the International Space Station (ISS) with Earth in the background, the Node Micrometeoroid/Orbital Debris Shield removal, the spacewalks performed by Mission Specialists Joseph Tanner and Carlos Noriega, the undocking of Endeavour and ISS, the Orbital Maneuvering System (OMS) firing, the payload bay doors closing, and the landing sequence of Endeavour. The Aurora Borealis and a night view of the French Rivera are seen from space.

Source record↗
NASA NTRS2001

STS-98 Mission Highlights Resource Tape

A continuation of 'STS-98 Mission Highlights Resource Tape, Part 1 of 3' (internal ID 2001054058), this video shows the activities of flight days four through seven of the STS-98 mission on Atlantis. 'STS-98 Mission Highlights Resource Tape, Part 3 of 3' (internal ID 2001054060) shows footage from flight days 8-11.

Source record↗
NASA NTRS2001

STS-98 Mission Highlights Resource Tape

A continuation of 'STS-98 Mission Highlights Resource Tape, Part 1 of 3' (internal ID 2001054058) and 'STS-98 Mission Highlights Resource Tape, Part 2 of 3' (internal ID 2001054059), this video concludes the overview of the STS-98 mission. Footage shows the activities of flight days 8 through 11 and the landing of Atlantis.

Source record↗
NASA NTRS2001

STS-98 Mission Highlights Resource Tape

An overview of the STS-98 mission is given through footage from each flight day, starting with the prelaunch preparations (crew breakfast, suitup, and boarding of Atlantis), countdown, and Atlantis' launch and ending with the activities of flight day four. Footage from the fourth flight day is continued on the video 'STS-98 Mission Highlights Resource Tape, Part 2 of 3' (internal ID 2001054059), which shows mission activities through flight day seven. 'STS-98 Mission Highlights Resource Tape, Part 3 of 3' (internal ID 2001054060) shows the end of the mission, including footage from flight days 8-11 and the landing of Atlantis.

Source record↗
NASA NTRS2000

2D Quantum Mechanical Study of Nanoscale MOSFETs

With the onset of quantum confinement in the inversion layer in nanoscale MOSFETs, behavior of the resonant level inevitably determines all device characteristics. While most classical device simulators take quantization into account in some simplified manner, the important details of electrostatics are missing. Our work addresses this shortcoming and provides: (a) a framework to quantitatively explore device physics issues such as the source-drain and gate leakage currents, DIBL, and threshold voltage shift due to quantization, and b) a means of benchmarking quantum corrections to semiclassical models (such as density-gradient and quantum-corrected MEDICI). We have developed physical approximations and computer code capable of realistically simulating 2-D nanoscale transistors, using the non-equilibrium Green's function (NEGF) method. This is the most accurate full quantum model yet applied to 2-D device simulation. Open boundary conditions and oxide tunneling are treated on an equal footing. Electrons in the ellipsoids of the conduction band are treated within the anisotropic effective mass approximation. We present the results of our simulations of MIT 25, 50 and 90 nm "well-tempered" MOSFETs and compare them to those of classical and quantum corrected models. The important feature of quantum model is smaller slope of Id-Vg curve and consequently higher threshold voltage. Surprisingly, the self-consistent potential profile shows lower injection barrier in the channel in quantum case. These results are qualitatively consistent with ID Schroedinger-Poisson calculations. The effect of gate length on gate-oxide leakage and subthreshold current has been studied. The shorter gate length device has an order of magnitude smaller current at zero gate bias than the longer gate length device without a significant trade-off in on-current. This should be a device design consideration.

Svizhenko, Alexei↗
NASA NTRS2001

Thermal Analysis of the MC1 Engine Turbopump

The MC1 Engine turbopump supplied the propellants to the main injector. The turbopump consisted of four parts; lox pump, interpropellant seal package (IPS), RP pump and turbine. The thermal analysis was divided into two 2D finite element models; Housing or stationary parts and rotor or rotating parts. Both models were analyzed at the same boundary conditions using SINDA. The housing model consisted of, lox pump housing, ips housing, RP housing, turbine inlet housing, turbine housing, exit guide vane, heat shield and both bearing outer races. The rotor model consisted of the lox impeller; lox end bearing and id race, RP impeller, and RP bearing and id race, shaft and turbine disk. The objectives of the analysis were to: (1) verified the original design and recommend modifications to it, (2) submitted a thermal environment to support the structural analysis, (3) support the component and engine test program. and (4) to support the X34 vehicle program.

Roman, Jose↗
NASA NTRS2002

Project to Interface Climate Modeling on Global and Regional Scales with Earth Observing (EOS) Observations

This ten-year NASA IDS project began in 1990. Its initial work plan adopted the NASA provided timeline that data would become available for new Earth Observing System (EOS) platforms beginning in 1995. Over its first phase, it was based at NCAR, which had submitted the original proposal and involved activities of a substantial number of co-investigators at NCAR who engaged in research over several areas related to the observations expected to be received from the EOS platforms. Their focus was the theme of use of EOS data for improving climate models for projecting global change. From the climate system viewpoint, the IDS addressed land, clouds-hydrological cycle, radiative fluxes and especially aerosol impacts, ocean and sea-ice, and stratosphere. Other research addressed issues of data assimilation, diagnostic analyses, and data set development from current satellite systems, especially use of SAR data for climate models.

Dickinson, Robert E.↗