Ignition and ignition propagation in solid propellant motors.
Solid propellant ignition and ignition propagation for rocket exhaust and hypergolic-type igniters
SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Solid propellant ignition and ignition propagation for rocket exhaust and hypergolic-type igniters
Small high-speed single-cylinder compression-ignition engines were tested to determine their performance characteristics under high supercharging. Calculations were made on the energy available in the exhaust gas of the compression-ignition engines. The maximum power at any given maximum cylinder pressure was obtained when the compression pressure was equal to the maximum cylinder pressure. Constant-pressure combustion was found possible at an engine speed of 2200 rpm. Exhaust pressures and temperatures were determined from an analysis of indicator cards. The analysis showed that, at rich mixtures with the exhaust back pressure equal to the inlet-air pressure, there is excess energy available for driving a turbine over that required for supercharging. The presence of this excess energy indicates that a highly supercharged compression-ignition engine might be desirable as a compressor and combustion chamber for a turbine.
A new hohlraum geometry or “Frustraum” is proposed that may enable 2–3× higher capsule absorbed x-ray energy than for nominally sized capsules in standard cylinders. The Frustraum geometry comprises two truncated conical halves (or “frusta”) joined at the waist. An associated larger waist volume above the capsule allows fielding ∼50% larger capsules than the nominal 1 mm (radius) scale. A key feature of the Frustraum is that the outer laser cones strike the Frustraum ends at a higher glancing angle (by ∼23°) compared with a cylinder and generate more specular reflection. A scenario for boosted symmetry control from the outer cones reflecting off a glancing angle hohlraum wall depends on the choice of electron flux limit in the simulations. Recent data from the National Ignition Facility using oversized aluminum shells in rugby-shaped hohlraums [Ping et al., Nat. Phys. 15, 138 (2019)] come closest to approximating a Frustraum and are consistent with a flux limit of 0.03–0.04 in matching the simulated Dante drive history, the backlit trajectory of the Al shell, neutron yield, and implosion time. Applying this simulation methodology to hot-spot ignition designs in a Frustraum shows effective symmetry control and sufficient drive (∼290 eV) to enable high yield, moderate convergence implosions. Simulations suggest that adjusting the obliquity of the Frustraum wall is a robust lever for symmetry tuning. A high adiabat (α = 4.6) ignition design with a shortened laser pulse (<7 ns) is proposed to provide further margin to potential late-time loss of symmetry control from hohlraum filling and anomalous sources of fuel preheat.
Laser–plasma interaction instabilities can be detrimental for direct-drive inertial confinement fusion by generating high-energy electrons that preheat the target. Moreover, an experimental platform has been developed and fielded on the National Ignition Facility to investigate hot-electron production from laser–plasma instabilities at direct-drive ignition-relevant conditions. The radiation-hydrodynamic code DRACO has been used to design planar-target experiments that generate plasma and interaction conditions comparable to direct-drive ignition designs: I L ~10 15 W/cm 2 , T e > 3 keV, and density-gradient scale lengths of L n ~ 600 μ m in the quarter-critical density region. The hot-electron properties were inferred by comparing the experimentally observed hard x-ray spectra to Monte Carlo simulations of hard x-ray emission from hot electrons depositing energy in the target. Hot-electron temperatures of ~40 keV to 60 keV and the fraction of laser energy converted to hot electrons of ~0.5% to 5% were inferred in plastic targets for laser intensities at the quarter-critical density surface of (~4 to 14) × 10 14 W/cm 2 . The use of silicon ablators was found to mitigate the hot-electron preheat by increasing the threshold laser intensity for hot-electron generation from ~3.5 × 10 14 W/cm 2 in plastic to ~6 × 10 14 W/cm 2 in silicon. The overall hot-electron production is further reduced in silicon ablators when the intensity threshold is exceeded.
A recent experiment conducted on the National Ignition Facility (NIF) described in the study by Abu-Shawareb et al. achieved a fusion yield output of 1.3 MJ from ~ 220 kJ of x-ray energy absorbed by the capsule, demonstrating remarkable progress in the field of laser driven inertial confinement fusion. In the study by A. R. Christopherson [“Effects of charged particle heating on the hydrodynamics of inertially confined plasmas,” Ph.D. thesis (2020)], the plasma conditions needed to claim the onset of ignition and burn propagation were outlined and multiple criterion were provided to assess progress in inertial fusion experiments. In this work, we modify the metrics from A. R. Christopherson to accurately calculate performance metrics for indirect-drive experiments on the NIF. We also show that performance metric trends observed in NIF data are consistent with theory and simulations. This analysis indicates that all the identified criterion for ignition and burn propagation have been exceeded by experiment 210 808.
We describe our current understanding of the variability and degradation mechanisms observed through a series of five indirectly driven inertial fusion implosions fielded at the National Ignition Facility in the fall of 2021, four of which attempted to reproduce the first experiment to achieve Lawson's criterion for ignition with a thermonuclear yield of 1.35 MJ on August 8, 2021. A large number of absolutely calibrated (imaging, time-resolved, and spectrally resolved) x-ray and neutron diagnostics are fielded on the NIF along multiple lines of sight for each experiment. This allows for a reconstruction of the DT fuel and ablator mix injected into the hotspot around peak burn. We show that nuclear yield variations are well reproduced by numerical modeling when the measured low mode asymmetries and mix mass are included. Furthermore, these observed perturbations during burn are linked to small variations in laser delivery and capsule defects. Stringent specifications are then set to achieve robust ignition with the implosion design studied in this paper.
This paper reviews scientific results from the pursuit of indirect drive ignition on the National Ignition Facility (NIF) and describes the program's forward looking research directions. In indirect drive on the NIF, laser beams heat an x-ray enclosure called a hohlraum that surrounds a spherical pellet. X-ray radiation ablates the surface of the pellet, imploding a thin shell of deuterium/tritium (DT) that must accelerate to high velocity (v > 350 km s –1 ) and compress by a factor of several thousand. Since 2009, substantial progress has been made in understanding the major challenges to ignition: Rayleigh Taylor (RT) instability seeded by target imperfections; and low-mode asymmetries in the hohlraum x-ray drive, exacerbated by laser-plasma instabilities (LPI). Requirements on velocity, symmetry, and compression have been demonstrated separately on the NIF but have not been achieved simultaneously. We now know that the RT instability, seeded mainly by the capsule support tent, severely degraded DT implosions from 2009–2012. Experiments using a 'high-foot' drive with demonstrated lower RT growth improved the thermonuclear yield by a factor of 10, resulting in yield amplification due to alpha particle heating by more than a factor of 2. Furthermore, large time dependent drive asymmetry in the LPI-dominated hohlraums remains unchanged, preventing further improvements. High fidelity 3D hydrodynamic calculations explain these results. Future research efforts focus on improved capsule mounting techniques and on hohlraums with little LPI and controllable symmetry. In parallel, we are pursuing improvements to the basic physics models used in the design codes through focused physics experiments.
Here, we use a subignition scale laser, the 30 kJ Omega, and a novel shallow-cone target to study laser-plasma interactions at the ablation-plasma density scale lengths and laser intensities anticipated for direct drive shock-ignition implosions at National Ignition Facility scale. Our results show that, under these conditions, the dominant instability is convective stimulated Raman scatter with experimental evidence of two plasmon decay (TPD) only when the density scale length is reduced. Particle-in-cell simulations indicate this is due to TPD being shifted to lower densities, removing the experimental back-scatter signature and reducing the hot-electron temperature. The experimental laser energy-coupling to hot electrons was found to be 1%–2.5%, with electron temperatures between 35 and 45 keV. Radiation-hydrodynamics simulations employing these hot-electron characteristics indicate that they should not preheat the fuel in MJ-scale shock ignition experiments.
Here, an inertial confinement fusion experiment, carried out at the National Ignition Facility, has achieved ignition by generating fusion energy exceeding the laser energy that drove the experiment. Prior to the experiment, a generative machine learning model that combines radiation hydrodynamics simulations, deep learning, experimental data, and Bayesian statistics was used to predict, with a probability greater than 70%, that ignition was the most likely outcome for this shot.
Hydrodynamic instability growth and its effects on capsule implosion performance are being studied at the National Ignition Facility (NIF). Experimental results have shown that low-mode instabilities are the primary culprit for yield degradation. Ignition type capsules with machined 2D sinusoidal defects were used to measure low-mode hydrodynamic instability growth in the acceleration phase of the capsule implosion. The capsules were imploded using ignition-relevant laser pulses and the ablation-front modulation growth was measured using x-ray radiography. The experimentally measured growth was in good agreement with simulations.
The ignition of a combustible gas mixture by a hot cylinder under the effect of a gravity field for steady state conditions is examined. For this purpose a horizontal cylinder is considered with gravity as a parameter together with a finite chemical reacting flow generated by free convection with the additional effect of diffusion. Both mass transfer and zero mass transfer cases are considered. By defining an ignition criterion the surface temperature and species are obtained from the analysis as a function of the gravity field. It is supposed that at the point of ignition the heat evolved in the gas is sufficiently high to attain a sustained combustion without any energy from the hot cylinder.
Extensive test data exist on the ignitability of nonmetallic materials in pure oxygen, but these characteristics are not as well understood for lesser oxygen concentrations. In this study, autogenous ignition temperature testing and pneumatic impact testing were used to better understand the effects of oxygen concentration on ignition of nonmetallic materials. Tests were performed using oxygen concentrations of 21, 34, 45, and 100 %. The following materials were tested: PTFE Teflon(Registered Trademark), Buna-N, Silicone, Zytel(Registered Trademark) 42, Viton(registered Trademark) A, and Vespel(Registered Trademark) SP-21.
The pursuit of demonstrating thermonuclear ignition and energy gain with single-shell targets on the National Ignition Facility (NIF) is ongoing since 2009. These targets rely on the formation of a high-temperature (~12 keV) “spark” in the deuterium-tritium (DT) fuel near capsule center that triggers an outwardly propagating self-sustaining burn or deflagration wave to the surrounding higher density fuel for realizing appreciable energy gain. This mode of thermonuclear burn is known as ‘hot spot’ ignition. Recent experiments with ‘high foot’ laser drive histories have demonstrated (~2x) net energy gain from the hot spot, but with no appreciable burn propagation into the dense fuel.
With the development of various low temperature engine combustion strategies, the behavior of gasoline-type fuels under compression ignition conditions has attracted extensive research interest. In this study, gasoline surrogates based on toluene primary reference fuel blends (TPRF) with different research and motor octane numbers (i.e., RON and MON) and fuel octane sensitivity (OS) have been strategically designed using a recently established surrogate model, and their combustion chemistry is further described using a well-validated kinetic mechanism. Based on a typical advanced compression ignition engine configuration, the crank angle corresponding to 50% total heat release (CA50) was utilized as an indicator of the overall fuel reactivity, and representative engine operating conditions have been selected based on the regime exhibited from the CA50 iso-contours. By combining the thermodynamic trajectory and ignition delay isocontours, useful insights on the fuel reactivity and sensitivity have been obtained to evaluate the fuel performance under various engine operating regimes with distinct chemistry, accounting for the effects of equivalence ratio and ratio of exhaust gas recirculation (EGR). This study provides useful insight on the different effects of engine operating conditions on a fuel’s performance following different engine trajectories, based on the different controlling fuel chemistry.
As the National Ignition Facility continues its campaign to achieve ignition, new methods and tools will be required to measure the quality of the target capsules used to achieve this goal. Techniques have been developed to measure capsule surface features using a phase-shifting diffraction interferometer and Leica Microsystems confocal microscope. These instruments produce multi-gigabyte datasets which consist of tens to hundreds of files. Existing software can handle viewing a small subset of an entire dataset, but none can view a dataset in its entirety. Additionally, without an established mode of transport that keeps the target capsules properly aligned throughout the assembly process, a means of aligning the two dataset coordinate systems is needed. The goal of this project is to develop web based software utilizing WebGL which will provide high level overview visualization of an entire dataset, with the capability to retrieve finer details on demand, in addition to facilitating alignment of multiple datasets with one another based on common features that have been visually identified by users of the system.
A summary of data and results from the first neutron images produced by the National Ignition Facility (NIF), Lawrence Livermore National Laboratory, Livermore, CA, USA are presented. An overview of the neutron imaging technique is presented, as well as a synopsis of the data collected and measurements made to date. Data form directly driven, DT filled microballoons, as well as, indirectly driven, cryogenically layered ignition experiments are presented. The data presented show that the primary cores from directly driven implosions are approximately twice as large, 64 {+-} 3 {mu}m, as indirect cores 25 {+-} 4 and 29 {+-} 4 {mu}m and more asymmetric, P2/P0 = 47% vs. -14% and 7%. Further, comparison with the size and shape of X-ray image data on the same implosions show good agreement, indicating X-ray emission is dominated by the hot regions of the implosion.
The National Ignition Facility (NIF) is a 192-beam Nd-glass laser facility presently under construction at Lawrence Livermore National Laboratory (LLNL) in support of inertial confinement fusion (ICF) and high-energy-density (HED) science. NIF will produce 1.8 MJ, 500 TW of ultraviolet light, making it the world's largest and most powerful laser system. NIF will be the world's preeminent facility for the study of matter at extreme temperatures and densities and for producing and developing ICF. The ignition studies will be the next important step in developing inertial fusion energy.
Measuring the shape of implosions is critical to inertial confinement fusion experiments at the National Ignition Facility. We have developed techniques that have proven successful for extracting shape information from images of x-ray self-emission recorded by a variety of diagnostic instruments for both DT-filled targets and low-yield surrogates. These key results help determine optimal laser and target parameters leading to ignition. We have compensated for instrumental response and have employed a variety of image processing methods to remove artifacts from the images while retaining salient features. The implosion shape has been characterized by decomposing intensity contours into Fourier and Legendre modes for different lines of sight. We also describe procedures we have developed for estimating uncertainties in these measurements.