Search NASA⌕ Search

SEARCH · Search NASA

Results for “Impurity diffusion”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

The role of B T -dependent flows on W accumulation at the edge of the confined plasma

Abstract Near-separatrix impurity accumulation between the crown and the outer midplane of tokamaks is a common feature in results from codes such as SOLPS-ITER and DIVIMP; however, experimental evidence of accumulation has only recently been obtained and is reported here. The codes find that the poloidal distribution of impurity ions in the scrape-off layer (SOL) depends primarily on toroidal field ( B T )-dependent parallel flow patterns of the background plasma and the parallel ion temperature gradient (∇ ‖ T ion ) force. Experimentally, Mach probes used in L-mode plasmas with favorable (for H-mode access) B T measure fast ( M ∼ 0.3–0.5) inner-target-directed (ITD) background plasma flows at the crown of single-null discharges. This study reports a set of DIVIMP simulations for two similar H-mode discharges from the DIII-D W metal rings campaign differing primarily in B T -direction to assess the effect that fast ITD flows have on the distribution of W ions in the SOL. It is found that for imposed ITD flows of M = 0.3, W ions that otherwise accumulate due to the ∇ ‖ T ion -force are largely flushed out. It is also found that doubling the radial diffusion coefficient from 0.3 to 0.6 m 2 s −1 prevents accumulation due to rapid cross-field transport into the far-SOL, where background plasma flows drain W ions to the divertors. Far-SOL W distributions from DIVIMP are then used to specify input to the impurity transport code 3DLIM, which is used to interpretively model collector probe (CP) deposition patterns measured in the ‘wall-SOL’. It is demonstrated that the deposition patterns are consistent with the DIVIMP predictions of near-SOL accumulation for the unfavorable- B T direction, and little/no accumulation for the favorable- B T direction. The wall-SOL CPs have thus provided the first experimental evidence, albeit indirect, of near-SOL W accumulation—finding it occurs for the unfavorable- B T direction only. For the favorable- B T direction, fast flows can largely prevent accumulation from occurring.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Tetrahedral Zn 2+ doping LiNi 0.6 Mn 0.2 Co 0.2 O 2 improves discharge capacity retention by altering surface Ni valence during cycling and preventing oxygen evolution

5 mol-% Zn 2+ was added to the co-precipitation synthesis of LiNi 0.6 Mn 0.2 Co 0.2 O 2 (NMC622) to understand Zn's effect on the structural and electronic properties of NMC622. Zn is determined to successfully dope into the NMC crystal lattice as there is an increase in d-spacing along the [003], [104], and [110] directions and an increase in molar volume (100.75 cm 3 mol -1 for NMC622 and 101.00 cm 3 mol -1 for Zn-NMC). Through XPS, Zn is determined to dope on the tetrahedral 6c Wyckoff site in the NMC structure and TEM-EDS reveals that despite a slight ZnO impurity phase, 1.4 mol-% Zn successfully dopes into the crystal structure. Furthermore, cyclic voltammetry shows a suppressed anodic wave associated with oxygen evolution and EIS demonstrates that Zn-doped NMC decreases charge transfer resistance and increases Li diffusion by an order of magnitude. After the formation cycles, NMC has a higher 1 C accessible capacity, 141 mAh/g, over Zn-NMC (132 mAh/g), but after long term cycling Zn-NMC has a higher accessible capacity (117 mAh/g compared to 96 mAh/g for NMC) and increases discharge capacity retention by 18% leading to longer cycle life.

Electrochemistry↗
DOE OSTI2020

Ultra-thin passivation layers in Cu(In,Ga)Se 2 thin-film solar cells: full-area passivated front contacts and their impact on bulk doping

In the search for highly transparent and non-toxic alternative front layers replacing state-of-the-art CdS in Cu(In,Ga)Se 2 thin-film solar cells, alternatives rarely exceed reference devices in terms of efficiency. Full-area ultra-thin aluminium oxide tunnelling layers do not require any contact patterning and thus overcome the main drawback of insulating passivation layers. Even a few monolayers of aluminium oxide can be deposited in a controlled manner by atomic layer deposition, they show excellent interface passivation properties, low absorption, and suitable current transport characteristics on test devices. Depositing a ZnO-based transparent front contact, however, results in extremely poor solar cell performance. The issue is not necessarily a low quality of the alternative front layer, but rather the intricate relation between front layer processing and electronic bulk properties in the absorber layer. We identify three challenges critical for the development of novel front passivation approaches:(i) both Cd and Zn impurities beneficially reduce the high native net dopant concentration in the space charge region, (ii) sputter deposition of ZnO damages the passivation layer resulting in increased interface recombination, (iii) thermal treatments of devices with ZnO layer result in substantial Zn diffusion, which can penetrate the full absorber thickness already at moderate temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2020

Enhancing nanostructured nickel-rich lithium-ion battery cathodes via surface stabilization

Layered, nickel-rich lithium transition metal oxides have emerged as leading candidates for lithium-ion battery (LIB) cathode materials. High-performance applications for nickel-rich cathodes, such as electric vehicles and grid-level energy storage, demand electrodes that deliver high power without compromising cell lifetimes or impedance. Nanoparticle-based nickel-rich cathodes seemingly present a solution to this challenge due to shorter lithium-ion diffusion lengths compared to incumbent micrometer-scale active material particles. However, since smaller particle sizes imply that surface effects become increasingly important, particle surface chemistry must be well characterized and controlled to achieve robust electrochemical properties. Moreover, residual surface impurities can disrupt commonly used carbon coating schemes, which result in compromised cell performance. Using x-ray photoelectron spectroscopy, here we present a detailed characterization of the surface chemistry of LiNi0.8Al0.15Co0.05O2 (NCA) nanoparticles, ultimately identifying surface impurities that limit LIB performance. With this chemical insight, annealing procedures are developed that minimize these surface impurities, thus improving electrochemical properties and enabling conformal graphene coatings that reduce cell impedance, maximize electrode packing density, and enhance cell lifetime fourfold. Overall, this work demonstrates that controlling and stabilizing surface chemistry enables the full potential of nanostructured nickel-rich cathodes to be realized in high-performance LIB technology.

Lim, Jin-Myoung↗
DOE OSTI2026

Fully generalized, turbulent trace impurity transport with Gkeyll and Flan in the DIII-D far-SOL

The Monte Carlo trace impurity turbulent transport code Flan is introduced for the first time. Flan follows impurities in a turbulent background plasma from Gkeyll using the Lorentz force to resolve the full particle gyro orbit. Collisions are handled using the Nanbu collision algorithm (Nanbu 1997 Phys. Rev. E 55 4642–52), and ionization/recombination is handled via ADAS coupling. The far-SOL of a generic DIII-D L-mode is simulated with and without the collision model to show how collisions affect radial tungsten transport. Anomalous diffusion coefficient (D r ) and pinch velocity (v p ) profiles are extracted from fits to the results. With collisions, D r and v p are between 0–1.0 m 2 s −1 and −100–100 m s −1 , respectively. Without collisions, D r and v p are between 0–0.3 m 2 s −1 and −50–50 m s −1 , respectively. Exponential fits to the radial W density profiles and experimental data from W deposition along a collector probe are in good agreement, demonstrating Flan as a useful interpretive modeling tool. Additional simulations show that impurity transport away from the wall increases with atomic number, though it is not clear why. Flan has the potential to better interpret existing data and improve reactor scale predictions of core contamination because the underlying physics model is very general and does not rely on arbitrary user-defined transport coefficients.

DIII-D↗
DOE OSTI2023

The physics basis to integrate an MHD stable, high-power hybrid scenario to a cool divertor for steady-state reactor operation

Abstract Coupling a high-performance core to a low heat flux divertor is a crucial step for ITER and a Fusion Pilot Plant or DEMO. Experiments in DIII-D recently expanded the steady-state hybrid scenario to high density and divertor impurity injection to study the feasibility of a radiating mantle solution. This work presents the physics basis for trade-offs between density, current drive and stability to tearing modes (TMs) at high β. EC power is crucial to tailor the plasma profiles into a passively stable state, and to eject impurities from the core. Off-axis EC depositions decrease the heating efficiency, but calculated electron heat transport coefficients show that this effect is partially mitigated by improved confinement inside the EC deposition. Additionally, the reduction in pressure is recovered by increasing the density. This favourable scaling of confinement with density was observed in high power plasmas for years, and this work provides a comprehensive explanation. ELITE predictions indicate that a path in peeling-ballooning stability opens up for certain conditions of density, power, q 95 and shaping, allowing the edge pressure to continue increasing without encountering a limit. In the core, calculated anomalous fast-ion diffusion coefficients are consistent with density fluctuation measurements in the toroidicity-induced Alfvén eigenmode range, showing that smaller fast-ion losses contribute to the enhanced confinement at high density. The edge integration study shows that divertor heat loads can be reduced with Ne and Ar injection, but this eventually triggers a cascade of n = 1, 2, 3 core TMs. We can now show that impurity radiation in the core is small and it is not the cause for the drop in confinement at high Ar and Ne injection rates. The overlap between the core TMs is consistent with the loss of pressure as estimated by the Belt model for the coupled rational surfaces. Optimization of these trade-offs has achieved plasmas with sustained H 98y2 = 1.7, f GW = 0.7 and ∼85% mantle radiation. The scenario and its variations at higher density and on- vs off-axis EC heating has been studied as a candidate for an integrated solution for several reactor designs, such as ITER, ARC, and the ARIES-ACT1 case, showing promising results in terms of fusion power and gain.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Amorphization and siliconization of silicon carbide as a first wall material

The understanding and prediction of silicon carbide (SiC) material evolution exposed to SOL plasma conditions is of prime interest because SiC represents a promising main chamber wall plasma-facing material for next-step fusion devices (low hydrogenic diffusion, good mechanical and thermal properties under neutron irradiation). Gross and net Si erosion rates from SiC surfaces in contact with a well-diagnosed L-mode plasma in the DIII-D tokamak have been simulated and the surface concentrations of impurities have been tracked as a function of time. Coupled simulation of surface model and impurity transport demonstrates amorphization of crystalline SiC exposed to L-mode plasma due to the accumulation of displacement damages under ion irradiation. This affects the lifetime of SiC plasma facing components. Surface evolution is tightly coupled to impurity transport in the plasma and therefore needs to be integrated with impurity transport simulations to effectively predict Si erosion rates and sub-surface concentrations as a function of time. The simulation workflow couples a semi-analytical surface model to the impurity transport code GITR. The surface model is a homogeneous mixed-material model that tracks physical & chemical sputtering and reflection of impurities. Gross erosion is primarily influenced by the background plasma parameters and redeposition patterns are mainly influenced by the prompt redeposition due to the gyro-orbits of impurity ions. Although crystalline form of SiC is preferable for fusion wall applications because of resistance to neutron irradiation, this work indicates that crystalline SiC will undergo amorphization under D plasma contact with implications of higher sputtering and fuel retention. These results direct us to explore the effects of amorphization on crystalline SiC and further the physics basis of SiC usage as first wall material for fusion environments.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Molecular-scale investigation of the oxidation behavior of chromia-forming alloys in high-temperature CO2

Abstract Current and future power systems require chromia-forming alloys compatible with high-temperature CO 2 . Important questions concerning the mechanisms of oxidation and carburization remain unanswered. Herein we shed light onto these processes by studying the very initial stages of oxidation of Fe22Cr and Fe22Ni22Cr model alloys. Ambient-pressure X-ray photoelectron spectroscopy enabled in situ analysis of the oxidizing surface under 1 mbar of flowing CO 2 at temperatures up to 530 °C, while postexposure analyses revealed the structure and composition of the oxidized surface at the near-atomic scale. We found that gas purity played a critical role in the kinetics of the reaction, where high purity CO 2 promoted the deposition of carbon and the selective oxidation of Cr. In contrast, no carbon deposition occurred in low purity CO 2 and Fe oxidation ensued, thus highlighting the critical role of impurities in defining the early oxidation pathway of the alloy. The Cr-rich oxide formed on Fe22Cr in high purity CO 2 was both thicker and more permeable to carbon compared to that formed on Fe22Ni22Cr, where carbon transport appeared to occur by atomic diffusion through the oxide. Alternatively, the Fe-rich oxide formed in low purity CO 2 suggested carbon transport by molecular CO 2 .

36 MATERIALS SCIENCE↗
DOE OSTI2022

Mechanical and Thermophysical properties of low enriched uranium-10wt% molybdenum rolled foils

In this study, low-enriched (~19.75% 235 U) U-10Mo(wt%) foils were evaluated for both mechanical and thermophysical properties to establish baseline characteristics prior to irradiation testing. Cast U-10Mo ingots were sequentially hot and cold rolled to two different final foil thicknesses, resulting in different levels of cold work being present in the finished foils. The mechanical response of the U-10Mo foils was evaluated in the temperature range of 293–623 K. Increasing test temperatures resulted in decreases of both yield and ultimate tensile strength. Comparison of results to earlier work performed on depleted U-10Mo rolled foils indicates that the material in this study has lower strength and increased ductility. However, a comparison of the two different foil thicknesses in this study found that they were nearly identical in yield and ultimate tensile strength, differing by only 10–20 MPa (<2%). Thermal conductivity was calculated from the measurements of specific heat, linear thermal expansion, and thermal diffusivity from 323 to 1273 K on both thicknesses of the foils. These data were approximately 5–10% lower than previously published data above 573 K and were similar to data for temperature ranges below 573 K. Differences are likely related to differences in grain size and/or impurity content and variation in fabrication history.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Wear Performance of incoloy 800HT and inconel 617 in various surface conditions for high-temperature gas-cooled reactor components

Incoloy™ 800HT and Inconel™ 617 are primary candidate structural materials for high-temperature gas-cooled reactors (HTGRs). Impurities (e.g., H 2 O, CH 4 ) in the coolant induce corrosion reactions that affect tribological behavior. We investigate the high-temperature tribological performance of the alloys under surface conditions including: conditioned in H 2 O-containing helium at elevated temperatures, hardened via the carbon-diffusion Kolsterising® treatment, and conditioned after hardening. Initial friction coefficients and volume removed serve as metrics for wear performance. In this work, we find that wear mechanisms including scuffing, glaze-oxide formation, and oxide-layer wear and break-through are governed by surface hardness, chemistry, and applied load. The formation of a glaze-oxide layer is achieved with an oxide of sufficient mechanical integrity if the oxide-substrate interface is strong and the load is low.

42 ENGINEERING↗
DOE OSTI2021

Chemical Complexity of Phosphorous-bearing Species in Various Regions of the Interstellar Medium

Phosphorus-related species are not known to be as omnipresent in space as hydrogen, carbon, nitrogen, oxygen, and sulfur-bearing species. Astronomers spotted very few P-bearing molecules in the interstellar medium and circumstellar envelopes. Limited discovery of the P-bearing species imposes severe constraints in modeling the P-chemistry. In this paper, we carry out extensive chemical models to follow the fate of P-bearing species in diffuse clouds, photon-dominated or photodissociation regions (PDRs), and hot cores/corinos. We notice a curious correlation between the abundances of PO and PN and atomic nitrogen. Since N atoms are more abundant in diffuse clouds and PDRs than in the hot core/corino region, PO/PN reflects <1 in diffuse clouds, ≪1 in PDRs, and >1 in the late warm-up evolutionary stage of the hot core/corino regions. During the end of the post-warm-up stage, we obtain PO/PN > 1 for hot core and <1 for its low-mass analog. We employ a radiative transfer model to investigate the transitions of some of the P-bearing species in diffuse cloud and hot core regions and estimate the line profiles. Our study estimates the required integration time to observe these transitions with ground-based and space-based telescopes. We also carry out quantum chemical computation of the infrared features of PH{sub 3}, along with various impurities. We notice that SO{sub 2} overlaps with the PH{sub 3} bending-scissoring modes around ∼1000–1100 cm{sup −1}. We also find that the presence of CO{sub 2} can strongly influence the intensity of the stretching modes around ∼2400 cm{sup −1} of PH{sub 3}.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Effect of Carbon on Void Nucleation in Iron

The study reports the significance of carbon presence in affecting void nucleation in Fe. Without carbon, void nucleation rates decrease gradually at high temperatures but remain significantly high and almost saturated at low temperatures. With carbon present, even at 1 atomic parts per million, void nucleation rates show a low-temperature cutoff. With higher carbon levels, the nucleation temperature window becomes narrower, the maximum nucleation rate becomes lower, and the temperature of maximum void nucleation shifts to a higher temperature. Fundamentally, this is caused by the change in effective vacancy diffusivity due to the formation of carbon-vacancy complexes. The high sensitivity of void nucleation to carbon comes from the high sensitivity of void nucleation to the vacancy arrival rate in a void. The void nucleation is calculated by first obtaining the effective vacancy diffusivity considering the carbon effect, then calculating the defect concentration and defect flux change considering both carbon effects and pre-existing dislocations, and finally calculating the void nucleation rate based on the recently corrected homogeneous void nucleation theory. The study is important not only in the fundamental understanding of impurity effects in ion/neutron irradiation but also in alloy engineering for judiciously introducing impurities to increase swelling resistance, as well as in the development of simulation and modeling methodologies applicable to other metals.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Upgrading the Performance and Stability of Lithium, Manganese-Rich Layered Oxide Cathodes with Combined-Formic Acid and Spinel Coating Treatment

We report improving sluggish rate performance and cycling stability of Li, Mn-rich cathode materials (LMR) is of great importance for practical implementation. Here, dual surface modification on LMR particles with formic acid washing and spinel coating improves the electrochemical performance. Dilute formic acid can remove the Li2CO3 surface impurities and selectively reduce Ni while significantly increasing specific surface area by ~32 %, unlocking more electrochemically active surfaces. Spinel coating enhances cycle stability by suppressing detrimental side reactions at electrode-electrolyte interfaces at high voltage. Post-annealing temperature was found to significantly affect the cathode performance. Higher temperature favors diffusion of transition metal (TM)/Li ions of the spinel coating from surface to the bulk, removing the coating by possible reconstruction into the layered structure and thus degrading the performance. The spinel coating also appears to increase Co 3+ segregation on the particle surface. Compared to the original material, the optimized sample demonstrates 47 % higher capacity retention at 3C and retains 89 % of initial capacity after 150 cycles at 0.5C. Besides, the specific energy density of 523 Wh kg -1 can be attained after 150 cycles at 0.5C. Moreover, the post-cycling analysis of modified sample verifies a better structural integrity with less particle cracking. Altogether, this study portrays an alternative strategy to overcome the shortcomings of LMR cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2022

First lithium experiments in HIDRA and evidence of helium retention during quasi-steady-state stellarator plasma operations

Recent experiments in Hybrid Illinois Device for Research and Applications (HIDRA) have had operational discharges between t discharge = 60 and 1000 s using electron cyclotron resonant heating (ECRH) of the plasma. This means that quasi-steady-state plasma discharges reach conditions to study long-pulse plasma material interactions (PMIs). The newly commissioned HIDRA-Material Analysis Test-stand PMI diagnostic is used to place a drop of lithium onto a heated tungsten surface, transfer the sample in-vacuo and expose it in a helium plasma. Helium is of interest as there is an open question to whether lithium will be able to remove helium ash in real fusion devices. The introduction of the W-Li sample in HIDRA resulted in evaporation of lithium into the helium plasma during a 600 s pulse and caused a reduction of over 90% in neutral pressure during the discharge. It was also observed that the plasma density and temperature increased by over 2.5 times. Using spectroscopy and a helium collisional radiative model, the peak temperature and density of the helium plasma can be monitored during the discharge. During lithium evaporation, as significant lithium ionization occurs, there is a 85% drop in the HIDRA vessel neutral pressure, despite a constant flow rate of He gas. This reduction in neutral pressure is supported by spectroscopy data with corresponding reductions in He I line intensities (587 nm, 667 nm, 706 nm, and 728 nm), as well as those of other impurities. At one point in the discharge a lithium plasma is created, as indicated by an increase in Li + emission and a complete reduction in He + emission, but the electron density jumps from ne = 3 × 10 18 m –3 to over ne = 8 × 10 18 m –3 while the core temperature stays relatively constant between Te = 16 eV and 20 eV. Once lithium has completely evaporated from the sample and the majority of the ionized lithium has diffused from the plasma to the vessel walls, pressure and spectroscopy data paired with He collisional radiative model calculations shows a re-establishment of a helium plasma in a low recycling regime. In this regime, the density drops down to ne = 2 × 10 18 m –3 and the electron temperature increases from T e = 20 eV to over T e = 50 eV indicating an increase in helium heating efficiency. This is also indicated by the He+ emission re-establishing and having a higher intensity. Here, we show the results from the first lithium campaign in HIDRA. In the presence of lithium, and in particular when lithium ions are present, the helium disappears from the plasma via an as of yet unknown complex relationship that needs to be further studied. The most likely explanation is that the lithium ions are distributed around the vessel and able to trap helium to the surface turning HIDRA into a large gettering surface. These results have potential implications on future plasma facing component design using liquid lithium for impurity and recycling control using limiters and divertors.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2026

Revealing short- and long-range Li-ion diffusion in Li 2 MnO 3 from finite-temperature dynamical mean field theory

Li 2 MnO 3 is a key component of Li-excess layered cathodes of the form (1 − x), LiMO 2 + x, Li 2 MnO 3 (M = Mn, Ni, Co, …), yet its role in setting Li-ion transport limitations remains under debate. Here, in this study, we combine DFT+U, finite-temperature DFT+DMFT with a continuous-time quantum Monte Carlo impurity solver, and nudged-elastic-band (NEB) calculations to study Li + migration in paramagnetic Li 2 MnO 3 in the presence of a single Li vacancy. Evaluating DMFT total energies along the DFT+U NEB geometries reveals that dynamical correlations strongly renormalize the lowest-barrier processes, reducing the activation energies to E a = 0.18 eV for the shortest-range hop and E a = 0.50 eV for the next-lowest (transport-controlling) step. The 0.18 eV barrier quantitatively reproduces the short-range activation energy from µ+SR, while the 0.50 eV barrier is consistent with the long-range transport scale extracted from ac-impedance measurements. This single-vacancy, paramagnetic DMFT description thus provides a unified interpretation of local and macroscopic probes without invoking clustered vacancy configurations or strong extrinsic disorder, consistent with nearly stoichiometric Li 2 MnO 3 powders. More broadly, our results highlight finite-temperature dynamical correlations as an essential ingredient for predicting ionic migration energetics in correlated oxide electrodes.

Lee, Alex Taekyung [University of Illinois, Chicag↗
DOE OSTI2023

Defects of perovskite semiconductor CsPbBr3 investigated via photoluminescence and thermally stimulated current spectroscopies

Halide perovskites are essential materials for hard radiation detectors at ambient temperature. To improve detector performance, charge transport must be investigated and optimized. Using photoluminescence (PL) and thermally stimulated current (TSC) spectroscopies, we investigate photogenerated charge carriers in Bridgman-grown CsPbBr3 single crystals to understand the nature of charge transport. PL spectroscopy of these halide perovskites revealed the presence of strong emission bands at the band edge, which were attributed to free or bound excitons. It is shown that a wide broadening of the excitonic linewidth in these halide perovskites arises from strong exciton–phonon coupling, which is substantially dominated by longitudinal optical phonons via Fröhlich interaction. An additional contribution due to the presence of ionized impurities was also observed. Crystals with a detectable sensitivity to high-energy gamma radiation are characterized by a higher intensity and a narrower linewidth of the principal PL peak at 2.326 eV. Defect states beyond 2.214 eV have a negative impact on detector sensitivity to high-energy gamma radiation. TSC spectroscopy reveals an array of trap levels spanning 0.15–0.70 eV, attributed to intrinsic point defects and multiple extrinsic defects involving dopants or impurities. Defects identified included Cs and Br vacancies, as well as Pb interstitials with concentrations in the 1011–1016 cm−3 range. Understanding how the synthesis process impacts the types and concentrations of the defects present is currently under investigation. Elimination or suppression of the defect/trap states should result in halide perovskite materials with longer carrier diffusion lengths and improved detector characteristics.

Physics↗
DOE OSTI2023

Robust Millisecond Coherence Times of Erbium Electron Spins

Erbium doped solids are prime candidates for quantum memories in optical quantum networks given their telecom-compatible photon emission. An electron spin of erbium with millisecond coherence time is desirable for generating remote entanglement between adjacent quantum network nodes. Here, in this study, we report GHz-range electron spin transitions of 167 Er 3+ in yttrium oxide (Y 2 O 3 ) matrix with coherence times that are consistently longer than a millisecond. By polarizing para magnetic impurity spins we achieve a spin T 2 up to 1.46 ms, and up to 7.1 ms after dynamical decoupling. These coherence lifetimes are among the longest found for erbium in crystalline matrices despite the presence of host nuclear spins. We further enhance the coherence time beyond conventional dynamical decoupling, using customized sequences to simultaneously mitigate spectral diffusion and dipolar interactions. Our study not only establishes 167 Er 3+ : Y 2 O 3 as a significant quantum memory platform but also provides a guideline for engineering long-lived erbium spins in a variety of host materials for quantum technologies.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2020

Superconducting magnesium diboride films for levitation of laser targets

Inertial confinement fusion targets would benefit from being levitated inside hohlraums to avoid capsule support-related implosion perturbations. Levitation inside a magnetic trap requires coating the capsule with a thin film that is superconducting at 20 K. Such non-epitaxial film growth on non-planar substrates is challenging. Here, we study Mg vapor annealing and solid-phase reactive inter-diffusion methods to form superconducting magnesium diboride (MgB 2 ) films on different planar and spherical carbon substrates, evaluating glassy carbon, polycrystalline diamond made by chemical vapor deposition, and carbon deposited by magnetron sputtering of graphite targets. Thin films of B and Mg are produced by magnetron sputtering onto stationary planar or rolling spherical substrates and annealed at either 600 or 850 °C in Mg vapor. The films are characterized by a combination of high-energy ion scattering, electron microscopy, and magnetometry. Results show that the critical superconducting temperature of resultant films depends on film microstructure and oxygen impurity content. The formation of MgB 2 films is also strongly substrate dependent, even in this case of non-epitaxial growth. Important factors to consider are oxygen outgassing of the substrate during thermal processing, substrate surface roughness, and the matching of thermal expansion coefficients of different layers in the multilayer structure.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗