Search NASA⌕ Search

SEARCH · Search NASA

Results for “InP”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2004

High Beginning-of-Life Efficiency p/n InP Solar Cells

We have achieved a new record efficiency of 17.6%, (AM0) for a p/n InP homo-epitaxy solar cell. In addition, we have eliminated a previously observed photo-degradation of cell performance, which was due to losses in J(sub sc). Cells soaked in AM0 spectrum at one-sun intensity for an hour showed no significant change in cell performance. We have discovered carrier passivation effects when using Zn as the p-type dopant in the OMVPE growth of InP and have found a method to avoid the unexpected effects which result from typical operation of OMVPE cell growth.

Hoffman, Richard W., Jr.↗
NASA NTRS2004

Hydrogen Passivation of Interstitial Zn Defects in Heteroepitaxial InP Cell Structures and Influence on Device Characteristics

Hydrogen passivation of heteroepitaxial InP solar cells is of recent interest for deactivation of dislocations and other defects caused by the cell/substrate lattice mismatch that currently limit the photovoltaic performance of these devices. In this paper we present strong evidence that, in addition to direct hydrogen-dislocation interactions, hydrogen forms complexes with the high concentration of interstitial Zn defects present within the p(+) Zn-doped emitter of MOCVD-grown heteroepitaxial InP devices, resulting in a dramatic increase of the forward bias turn-on voltage by as much as 280 mV, from ~680 mV to ~960 mV. This shift is reproducible and thermally reversible and no such effect is observed for either n(+)p structures or homoepitaxial p(+)n structures grown under identical conditions. A combination of photoluminescence (PL), electrochemical C-V dopant profiling, SIMS and I-V measurements were performed on a set of samples having undergone a matrix of hydrogenation and post-hydrogenation annealing conditions to investigate the source of this voltage enhancement and confirm the expected role of interstitial Zn and hydrogen. A precise correlation between all measurements is demonstrated which indicates that Zn interstitials within the p(+) emitter and their interaction with hydrogen are indeed responsible for this device behavior.

Ringel, S. A.↗
NASA NTRS2005

Beyond G-band : a 235 GHz InP MMIC amplifier

We present results on an InP monolithic millimeter- wave integrated circuit (MMIC) amplifier having 10-dB gain at 235 GHz. We designed this circuit and fabricated the chip in Northrop Grumman Space Technology's (NGST) 0.07- m InP high electron mobility transistor (HEMT) process. Using a WR3 (220-325 GHz) waveguide vector network analyzer system interfaced to waveguide wafer probes, we measured this chip on-wafer for -parameters. To our knowledge, this is the first time a WR3 waveguide on-wafer measurement system has been used to measure gain in a MMIC amplifier above 230 GHz.

high electron mobility transistors (HEMTs)↗
NASA NTRS2009

InP Heterojunction Bipolar Transistor Amplifiers to 255 GHz

Two single-stage InP heterojunction bipolar transistor (HBT) amplifiers operate at 184 and 255 GHz, using Northrop Grumman Corporation s InP HBT MMIC (monolithic microwave integrated circuit) technology. At the time of this reporting, these are reported to be the highest HBT amplifiers ever created. The purpose of the amplifier design is to evaluate the technology capability for high-frequency designs and verify the model for future development work.

Radisic, Vesna↗
NASA NTRS2008

Three-Stage InP Submillimeter-Wave MMIC Amplifier

A submillimeter-wave monolithic integrated- circuit (S-MMIC) amplifier has been designed and fabricated using an indium phosphide (InP) 35-nm gate-length high electron mobility transistor (HEMT) device, developed at Northrop Grumman Corporation. The HEMT device employs two fingers each 15 micrometers wide. The HEMT wafers are grown by molecular beam epitaxy (MBE) and make use of a pseudomorphic In0.75Ga0.25As channel, a silicon delta-doping layer as the electron supply, an In0.52Al0.48As buffer layer, and an InP substrate. The three-stage design uses coplanar waveguide topology with a very narrow ground-to-ground spacing of 14 micrometers. Quarter-wave matching transmission lines, on-chip metal-insulator-metal shunt capacitors, series thin-film resistors, and matching stubs were used in the design. Series resistors in the shunt branch arm provide the basic circuit stabilization. The S-MMIC amplifier was measured for S-parameters and found to be centered at 320 GHz with 13-15-dB gain from 300-345 GHz. This chip was developed as part of the DARPA Submillimeter Wave Imaging Focal Plane Technology (SWIFT) program (see figure). Submillimeter-wave amplifiers could enable more sensitive receivers for earth science, planetary remote sensing, and astrophysics telescopes, particularly in radio astronomy, both from the ground and in space. A small atmospheric window at 340 GHz exists and could enable ground-based observations. However, the submillimeter-wave regime (above 300 GHz) is best used for space telescopes as Earth s atmosphere attenuates most of the signal through water and oxygen absorption. Future radio telescopes could make use of S-MMIC amplifiers for wideband, low noise, instantaneous frequency coverage, particularly in the case of heterodyne array receivers.

Pukala, David↗
NASA NTRS2009

Differential InP HEMT MMIC Amplifiers Embedded in Waveguides

Monolithic microwave integrated-circuit (MMIC) amplifiers of a type now being developed for operation at frequencies of hundreds of gigahertz contain InP high-electron-mobility transistors (HEMTs) in a differential configuration. The differential configuration makes it possible to obtain gains greater than those of amplifiers having the single-ended configuration. To reduce losses associated with packaging, the MMIC chips are designed integrally with, and embedded in, waveguide packages, with the additional benefit that the packages are compact enough to fit into phased transmitting and/or receiving antenna arrays. Differential configurations (which are inherently balanced) have been used to extend the upper limits of operating frequencies of complementary metal oxide/semiconductor (CMOS) amplifiers to the microwave range but, until now, have not been applied in millimeter- wave amplifier circuits. Baluns have traditionally been used to transform from single-ended to balanced configurations, but baluns tend to be lossy. Instead of baluns, finlines are used to effect this transformation in the present line of development. Finlines have been used extensively to drive millimeter- wave mixers in balanced configurations. In the present extension of the finline balancing concept, finline transitions are integrated onto the affected MMICs (see figure). The differential configuration creates a virtual ground within each pair of InP HEMT gate fingers, eliminating the need for inductive vias to ground. Elimination of these vias greatly reduces parasitic components of current and the associated losses within an amplifier, thereby enabling more nearly complete utilization of the full performance of each transistor. The differential configuration offers the additional benefit of multiplying (relative to the single-ended configuration) the input and output impedances of each transistor by a factor of four, so that it is possible to use large transistors that would otherwise have prohibitively low impedances. Yet another advantage afforded by the virtual ground of the differential configuration is elimination of the need for a ground plane and, hence, elimination of the need for back-side metallization of the MMIC chip. In turn, elimination of the back-side metallization simplifies fabrication, reduces parasitic capacitances, and enables mounting of the MMIC in the electric-field plane ("E-plane") of a waveguide. E-plane mounting is consistent with (and essential for the utility of) the finline configuration, in which transmission lines lie on a dielectric sheet in the middle of a broad side of the waveguide. E-plane mounting offers a combination of low loss and ease of assembly because no millimeter-wave wire bonds or transition substrates are required. Moreover, because there is no ground plane behind the MMIC, the impedance for the detrimental even (single-ended) mode is high, suppressing coupling to that mode. Still another advantage of E-plane mounting is that the fundamental waveguide mode is inherently differential, eliminating the need for a balun to excite the differential mode.

Kangaslahti, Pekka↗
NASA NTRS2010

A 311-GHz Fundamental Oscillator Using InP HBT Technology

This oscillator uses a single-emitter 0.3- m InP heterojunction bipolar transistor (HBT) device with maximum frequency of oscillation (fmax) greater than 500 GHz. Due to high conductor and substrate losses at submillimeterwave frequencies, a primary challenge is to efficiently use the intrinsic device gain. This was done by using a suitable transmission-line media and circuit topology. The passive components of the oscillator are realized in a twometal process with benzocyclobutene (BCB) used as the primary transmission line dielectric. The circuit was designed using microstrip transmission lines. The oscillator is implemented in a common-base topology due to its inherent instability, and the design includes an on-chip resonator, outputmatching circuitry, and an injection-locking port, the port being used to demonstrate the injection-locking prin ciple. A free-running frequency of 311.6 GHz has been measured by down-converting the signal. Ad di tionally, injection locking has been successfully demonstrated with up to 17.8 dB of injection-locking gain. The injection-locking reference signal is generated using a 2 20 GHz frequency synthesizer, followed by a doubler, active tripler, a W-band amplifier, and then a passive tripler. Therefore, the source frequency is multiplied 18 times to obtain a signal above 300 GHz that can be used to injection lock the oscillator. Measurement shows that injection locking has improved the phase noise of the oscillator and can be also used for synchronizing a series of oscillators. A signal conductor is implemented near the BCP -InP interface and the topside of the BCB layer is fully metallized as a signal ground. Because the fields are primarily constrained in the lower permittivity BCB region, this type of transmission line is referred to as an inverted microstrip. In addition, both common-emitter and commonbase circuits were investigated to determine optimum topology for oscillator design. The common -base topology required smaller amount of feedback than the common-emitter design, therefore preserving device gain, and was chosen for the oscillator design. The submillimeter-wave region offers several advantages for sensors and communication systems, such as high resolution and all-weather imaging due to the short-wavelength, and improved communication speeds by access to greater frequency bandwidth. This oscillator circuit is a prototype of the first HBT oscillator operating above 300 GHz. Additional development is necessary to increase the output power of the circuit for radar and imaging applications.

Gaier, Todd↗
NASA NTRS2005

Adding GaAs Monolayers to InAs Quantum-Dot Lasers on (001) InP

In a modification of the basic configuration of InAs quantum-dot semiconductor lasers on (001)lnP substrate, a thin layer (typically 1 to 2 monolayer thick) of GaAs is incorporated into the active region. This modification enhances laser performance: In particular, whereas it has been necessary to cool the unmodified devices to temperatures of about 80 K in order to obtain lasing at long wavelengths, the modified devices can lase at wavelengths of about 1.7 microns or more near room temperature. InAs quantum dots self-assemble, as a consequence of the lattice mismatch, during epitaxial deposition of InAs on ln0.53Ga0.47As/lnP. In the unmodified devices, the quantum dots as thus formed are typically nonuniform in size. Strainenergy relaxation in very large quantum dots can lead to poor laser performance, especially at wavelengths near 2 microns, for which large quantum dots are needed. In the modified devices, the thin layers of GaAs added to the active regions constitute potential-energy barriers that electrons can only penetrate by quantum tunneling and thus reduce the hot carrier effects. Also, the insertion of thin GaAs layer is shown to reduce the degree of nonuniformity of sizes of the quantum dots. In the fabrication of a batch of modified InAs quantum-dot lasers, the thin additional layer of GaAs is deposited as an interfacial layer in an InGaAs quantum well on (001) InP substrate. The device as described thus far is sandwiched between InGaAsPy waveguide layers, then further sandwiched between InP cladding layers, then further sandwiched between heavily Zn-doped (p-type) InGaAs contact layer.

Qiu, Yueming↗
NASA NTRS2012

InP HEMT Integrated Circuits for Submillimeter Wave Radiometers in Earth Remote Sensing

The operating frequency of InP integrated circuits has pushed well into the Submillimeter Wave frequency band, with amplification reported as high as 670 GHz. This paper provides an overview of current performance and potential application of InP HEMT to Submillimeter Wave radiometers for earth remote sensing.

High electron mobility transistor (HEMT)↗
NASA NTRS2004

Self-assembled InAsSb quantum dots on (001) InP substrates

Self-assembled InAsSb quantum dots (QD) on (001) InP substrates have been grown using metalorganic vapor phase epitaxy. The dot density and size are found to be strongly dependent on the presence of arsine. Direct deposition of InSb on InP and GaSb substrates formed large islands of InSb with low density of less than 53109/cm², however, InAsSb QDs of density as high as 4 X10¹º/cm² could be self-assembled by alternating group III and group V precursors, and high density almost pure InSb QDs were achieved on In0.53Ga0.47As/InP. The formation of high density InAsSb QDs is a result of a local nonequilibrium process and a reduction in mobility of In adatoms on the growth surface due to the presence of arsenic atoms, and in the case of high density almost pure InSb QDs on InGaAs/InP, the InAs interface layer is believed to be responsible. Photoluminescence shows that InSb QDs emit light at room temperature in the range of 1.7–2.2µm.

Uhl, David↗
NASA NTRS1998

InP HEMT MMICs for Radiometer Applications

We present results of developments of low noise millimeter wave receivers for space applications utilizing InP HEMT monolithic microwave integrated circuts (MMICs).

low noise millimeter wave receivers InP HEMT monol↗
NASA NTRS2004

Common base amplifier with 7 - dB gain at 176 GHz in InP mesa DHBT technology

We report a single stage tunded amplifier that exhibits 7 dB small signal gain at 176 GHz. Common Base topology is chosen as it has the best maximum stable gain (MSG) in this frequency band when compared to common emitter and common collector topologies. The amplifiers are designed and fabricated in InP mesa double heterojunction bipolar transistor (DHBT) technology.

millimeter-wave amplifier↗
NASA NTRS2019

A 220-GHz InP HEMT Direct Detection Polarimeter

In this article, a 220-GHz direct detection polarimetric receiver is reported. This polarimetric receiver is intended for sensing of the microphysical properties of cloud ice in the earth's upper atmosphere. In the article, we report the measured RF performance, including RF gain of approximately 35 dB per channel and integrated noise figure of the receiver. The noise figure is measured to be 5.1 dB for the horizontally polarized channel and 5.4 dB for the vertically polarized channel. The receiver measures only 1.8 cm × 3.0 cm × 6.4 cm and has a total regulated dc power consumption of 520 mW. This article represents the first 220-GHz polarimetric direct detection receiver and is enabled by an advanced 25-nm indium phosphide (InP) HEMT monolithic microwave integrated circuit (MMIC) technology.

Indium phosphide (InP)↗
DOE OSTI2026

Tracking Optical Phonon Dynamics in InP Nanocrystals via Transient Absorption and Femtosecond Stimulated Raman Spectroscopy

Semiconductor nanocrystals (NCs) offer actualized and prospective utility in optoelectronic technologies, yet key aspects of their thermal and vibrational behaviors remain unresolved. Compared with bulk crystals, heat dissipation involving NCs can differ substantially owing to pervasiveness of interfacial scattering, phonon confinement, and relaxed phonon momentum selection rules, as well as influences of ligands. Here, in addition to transient absorption, we use femtosecond stimulated Raman spectroscopy to track nonequilibrium optical-phonon dynamics in InP NCs capped with myristic acid ligands and compare the same particles coated with a ZnS shell. We identify distinct phonon decay pathways in ligand-capped versus ZnS-shelled NCs. Increasing the excitation density and introducing the ZnS shell measurably modify optical-phonon lifetimes, whereas phonon formation times remain largely unchanged. In addition, we observe phonon mode softening in ligand-capped nanocrystals, consistent with lattice expansion. Together, these results demonstrate that core–shell structures can strongly govern nanocrystal thermal dissipation pathways and should be considered a key design parameter for optoelectronic operation.

dissipation↗
DOE OSTI2024

Optimizing the quality factor of InP nanobeam cavities using atomic layer deposition

Photonic crystal nanobeam cavities are valued for their small mode volume, CMOS compatibility, and high coupling efficiency-crucial features for various low-power photonic applications and quantum information processing. However, despite their potential, nanobeam cavities often suffer from low quality factors due to fabrication imperfections that create surface states and optical absorption. In this work, we demonstrate InP nanobeam cavities with up to 140% higher quality factors by applying a coating of Al 2 O 3 via atomic layer deposition to terminate dangling bonds and reduce surface absorption. Additionally, changing the deposition thickness allows precise tuning of the cavity mode wavelength without compromising the quality factor. This Al 2 O 3 atomic layer deposition approach holds great promise for optimizing nanobeam cavities that are well-suited for integration with a wide range of photonic applications.

42 ENGINEERING↗
DOE OSTI2025

Supercontinuum generation in oxide and semiconductor materials (InP, Si, GaN, GaAs, PbMoO 4 , YVO 4 , ZGP, TiO 2 , diamond) pumped by radiation of the Cr:ZnS fs-MOPA system

Ultrashort light sources in the middle-infrared range are highly beneficial for applications such as gas molecular spectroscopy, remote sensing, atmospheric science, medical treatments, and light–matter interaction studies. Ultrafast lasers utilizing chromium-doped ZnS/Se (Cr:ZnS/Se) have proven to be robust and stable solutions within this spectral region. Nonlinear spectral broadening is fundamentally important, as it pushes the pulse duration limits imposed by the bandwidth of laser media. In this study, we demonstrate the spectral broadening and supercontinuum generation in several bulk materials, including InP, Si, GaN, GaAs, PbMoO 4 , YVO 4 , diamond, and TiO 2 , using pump radiation with up to 4 W average power centered at 2.35 µm from a Cr:ZnS femtosecond MOPA system. Some of the investigated materials have excellent potential as effective media for middle-infrared supercontinuum generation, demonstrating the feasibility of developing a single-cycle pulse middle-infrared laser system.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗