Search NASA⌕ Search

SEARCH · Search NASA

Results for “LANDING SPEED”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1958

Investigation of Incipient Spin Characteristics of a 1/35-Scale Model of the Convair F-102A Airplane, Coord. No. AF-AM-79

Incipient spin characteristics have been investigated on a l/35-scale dynamic model of the Convair F-10% airplane. The model was launched by a catapult apparatus into free flight with various control settings, and the motions obtained were photographed. The model was ballasted for the combat loading. All tests were made with the speed brakes and landing gear retracted, and engine effects were not simulated. The results of the investigation indicated that the model would enter motions apparently simulating entry phases of spins when the elevators were deflected full up. Deflecting the rudder had little effect on the direction of the motion obtained, but when ailerons were deflected the model always rotated in a direction opposite to the aileron setting (that is, the model entered a right spin with the stick to the left). The ailerons were very influential in initiating spin entry, and the pilot should avoid, as far as possible, the use of ailerons in low-speed flight.

Healy, Frederick M.↗
NASA NTRS1991

A compensatory algorithm for the slow-down effect on constant-time-separation approaches

In seeking methods to improve airport capacity, the question arose as to whether an electronic display could provide information which would enable the pilot to be responsible for self-separation under instrument conditions to allow for the practical implementation of reduced separation, multiple glide path approaches. A time based, closed loop algorithm was developed and simulator validated for in-trail (one aircraft behind the other) approach and landing. The algorithm was designed to reduce the effects of approach speed reduction prior to landing for the trailing aircraft as well as the dispersion of the interarrival times. The operational task for the validation was an instrument approach to landing while following a single lead aircraft on the same approach path. The desired landing separation was 60 seconds for these approaches. An open loop algorithm, previously developed, was used as a basis for comparison. The results showed that relative to the open loop algorithm, the closed loop one could theoretically provide for a 6 pct. increase in runway throughput. Also, the use of the closed loop algorithm did not affect the path tracking performance and pilot comments indicated that the guidance from the closed loop algorithm would be acceptable from an operational standpoint. From these results, it is concluded that by using a time based, closed loop spacing algorithm, precise interarrival time intervals may be achievable with operationally acceptable pilot workload.

Abbott, Terence S.↗
NASA NTRS1960

Landing Characteristics of a Reentry Capsule with a Torus-Shaped Air Bag for Load Alleviation

An experimental investigation has been made to determine the landing characteristics of a conical-shaped reentry capsule by using torus-shaped air bags for impact-load alleviation. An impact bag was attached below the large end of the capsule to absorb initial impact loads and a second bag was attached around the canister to absorb loads resulting from impact on the canister when the capsule overturned. A 1/6-scale dynamic model of the configuration was tested for nominal flight paths of 60 deg. and 90 deg. (vertical), a range of contact attitudes from -25 deg. to 30 deg., and a vertical contact velocity of 12.25 feet per second. Accelerations were measured along the X-axis (roll) and Z-axis (yaw) by accelerometers rigidly installed at the center of gravity of the model. Actual flight path, contact attitudes, and motions were determined from high-speed motion pictures. Landings were made on concrete and on water. The peak accelerations along the X-axis for landings on concrete were in the order of 3Og for a 0 deg. contact attitude. A horizontal velocity of 7 feet per second, corresponding to a flight path of 60 deg., had very little effect upon the peak accelerations obtained for landings on concrete. For contact attitudes of -25 deg. and 30 deg. the peak accelerations along the Z-axis were about +/- l5g, respectively. The peak accelerations measured for the water landings were about one-third lower than the peak accelerations measured for the landings on concrete. Assuming a rigid body, computations were made by using Newton's second law of motion and the force-stroke characteristics of the air bag to determine accelerations for a flight path of 90 deg. (vertical) and a contact attitude of 0 deg. The computed and experimental peak accelerations and strokes at peak acceleration were in good agreement for the model. The special scaling appears to be applicable for predicting full-scale time and stroke at peak acceleration for a landing on concrete from a 90 deg. flight path at a 0 deg. It appears that the full-scale approximately the same as those obtained from the model for the range of attitudes and flight paths investigated.

McGehee, John R.↗
NASA NTRS2002

Descent-speed testing of a hazard detection system for safe landing on Mars

In a previous paper we described an approach for testing a prototype system designed to detect hazards during the terminal descent phase of a mission to Mars. The system under development at the Jet Propulsion Laboratory (JPL) utilizes a scanning laser radar and an inertial measurement unit to map the landing zone, identify hazards, and thenguide the vehicle to a safe landing site. The test approach consisted of a placing this system on a rocket sled, accelerating the sled to typical descent speeds, and mapping a simulated Martian terrain. The data would then be processed to identify hazards and locate a safe landing site. Since ref. 1 was written several such tests have been performed. In this paper we provide an update on the testing methodology and we present preliminary results from one of the tests.

hazard↗
NASA NTRS2008

Photogrammetric Measurements of CEV Airbag Landing Attenuation Systems

High-speed photogrammetric measurements are being used to assess the impact dynamics of the Orion Crew Exploration Vehicle (CEV) for ground landing contingency upon return to earth. Test articles representative of the Orion capsule are dropped at the NASA Langley Landing and Impact Research (LandIR) Facility onto a sand/clay mixture representative of a dry lakebed from elevations as high as 62 feet (18.9 meters). Two different types of test articles have been evaluated: (1) half-scale metal shell models utilized to establish baseline impact dynamics and soil characterization, and (2) geometric full-scale drop models with shock-absorbing airbags which are being evaluated for their ability to cushion the impact of the Orion CEV with the earth s surface. This paper describes the application of the photogrammetric measurement technique and provides drop model trajectory and impact data that indicate the performance of the photogrammetric measurement system.

Barrows, Danny A.↗
DOE OSTI2025

Quantifying Uncertainties in Modeling Wind Resource Data from Different PBL Schemes in the WRF Model: A Case Study Over the Puerto Rico Region

This study examines the modeling uncertainty of wind resource data stemming from the use of various planetary boundary layer (PBL) parameterizations available in the Weather Research and Forecasting (WRF) model. WRF-based wind simulations spanning 20 years at 3-km resolution using 11 different PBL schemes are used to objectively investigate the uncertainty in modeling wind speed for land-based wind (LBW) and offshore wind (OSW) locations in Puerto Rico. The uncertainty in the wind modeling for the 20-year dataset is quantified using the spread index (SI) and standard deviation (SD). For virtual LBW and OSW sites, the SI and SD values are analyzed as calculated across various spatial and temporal scales. Because the PBL's atmospheric stability conditions can be characterized into two dominant categories, the study focuses on analyzing the SI and SD for daytime (mainly unstable PBL conditions) and nighttime (mainly stable PBL conditions). For wind shear (10 m-200 m) at the OSW and LBW sites, WRF-based numerical experiments indicate the following SI (or SD) ranges: 39%-94% (0.74 m/s-1.44 m/s) during the daytime for OSW, 50%-75% (0.68 m/s-1.19 m/s) during the daytime for LBW, 37%-60% (0.73 m/s-1.12 m/s) during the nighttime for OSW, and 57%-143 % (0.65 m/s-1.43 m/s) during the nighttime for LBW. While a high SI is observed when modeling LBW during the nighttime, there are notable modeling uncertainties during the daytime on the leeward side of the orographic barriers for Puerto Rico.

17 WIND ENERGY↗
DOE OSTI2026

Implementation of a Three-Dimensional Planetary Boundary Layer Parameterization in a Coupled Modeling System and Evaluation of "Gray Zone" Simulations of a Wind-Wave Event Off the US California Coast Using Observations

A three-dimensional (3D) planetary boundary layer (PBL) parameterization was added to the Coupled Ocean Atmosphere Wave Sediment Transport (COAWST) model and the first coupled atmosphere/wave "gray zone" simulations were carried out using the 3D PBL parameterization. A case study of a significant wind-wave event from 4-8 November 2020 off the US west coast was examined, with a focus on the impacts of the event within an approximate 280x280 km central California coastal region covering the Bureau of Ocean Energy Management Morro Bay wind energy lease area. Simulations with both one-dimensional (1D; Yonsei University) and 3D PBL parameterizations were examined in this nest with ..delta..x=400 m. Two-way coupling was active, with near-surface winds feeding back to the wave model and bulk wave statistics feeding back to the atmospheric model. Both simulations compared favorably with buoy observations in capturing the timing and magnitude of wind speed, temperature, dewpoint, and significant wave height, as the front associated with the maritime weather system moved southward across coastal California. However, wind speed errors over land were larger. Time series of the vertical profile of winds below z=250 m from the simulations compared favorably with observations from the US Dept. of Energy Morro Bay Doppler lidar buoy. Differences between the coupled 1D and 3D PBL simulations were minor. The most notable difference was that the simulation using the 3D PBL parameterization had approximately 10 % weaker winds at the peak of the event causing 10 % lower significant wave heights. This difference was shown to be mostly due to differences in the vertical mixing treatment between the parameterizations, in particular the nonlocal downward mixing of higher momentum air in the 1D Yonsei University parameterization in convective conditions. Overall, this work demonstrates that the 3D PBL parameterization can be used in a coupled atmosphere/wave modeling framework with similar behaviors as traditional PBL parameterizations that do not provide horizontal turbulent variances and fluxes.

16 TIDAL AND WAVE POWER↗
NASA NTRS1971

Heat addition to a subsonic boundary layer: A preliminary analytical study

A preliminary analytical study of the effects of heat addition to the subsonic boundary layer flow over a typical airfoil shape is presented. This phenomenon becomes of interest in the space shuttle mission since heat absorbed by the wing structure during re-entry will be rejected to the boundary layer during the subsequent low speed maneuvering and landing phase. A survey of existing literature and analytical solutions for both laminar and turbulent flow indicate that a heated surface generally destabilizes the boundary layer. Specifically, the boundary layer thickness is increased, the skin friction at the surface is decreased and the point of flow separation is moved forward. In addition, limited analytical results predict that the angle of attack at which a heated airfoil will stall is significantly less than the stall angle of an unheated wing. These effects could adversely affect the lift and drag, and thus the maneuvering capabilities of booster and orbiter shuttle vehicles.

Macha, J. M.↗
NASA NTRS1974

HFL-10 lifting body flight control system characteristics and operational experience

A flight evaluation was made of the mechanical hydraulic flight control system and the electrohydraulic stability augmentation system installed in the HL-10 lifting body research vehicle. Flight tests performed in the speed range from landing to a Mach number of 1.86 and the altitude range from 697 meters (2300 feet) to 27,550 meters (90,300 feet) were supplemented by ground tests to identify and correct structural resonance and limit-cycle problems. Severe limit-cycle and control sensitivity problems were encountered during the first flight. Stability augmentation system structural resonance electronic filters were modified to correct the limit-cycle problem. Several changes were made to control stick gearing to solve the control sensitivity problem. Satisfactory controllability was achieved by using a nonlinear system. A limit-cycle problem due to hydraulic fluid contamination was encountered during the first powered flight, but the problem did not recur after preflight operations were improved.

Painter, W. D.↗
NASA NTRS1981

Recent Progress in V/STOL Aircraft Technology

Results from wind tunnel and flight tests investigations for V/STOL aircraft are reviewed. Primary emphasis is given to technical results relating to three types of subsonic aircraft: a quiet STOL aircraft; a tilt rotor aircraft; and a turbofan V/STOL aircraft. Comparison and correlation between theoretical and experimental results and between wind tunnel and flight test results, is made. The quiet STOL aircraft technology results are primarily those derived from the NASA/Boeing Quiet Short Haul Technology (QSRA) program. The QSRA aircraft uses an upper surface blown flap and develops a usable engine-out landing approach lift coefficient of 5.5 and landing distances less than 1,000 ft. The tilt rotor aircraft technology results are those obtained from the NASA/Army/Navy/Bell (XV-15-TRRA) aircraft flight investigations. The TRRA is a twin rotor research aircraft capable of vertical takeoff and landing and cruise speeds of 300 knots. The turbofan V/STOL aircraft technology results are from static ground facility and wind tunnel investigations of a NASA/NAVY/Grumman full scale lift/cruise fan aircraft model, which features two tilting nacelles with TF-34 engines.

Roberts, L.↗
NASA NTRS1981

Chasing the Space Shuttle

The use and modifications of the T-38 aircraft as chase planes for the STS-1 landing are discussed. Two planes tracked the approach at Edwards AFB, with the lead plane responsible for airspeed and altimetry calibration, technical photography, landing gear status, and height-above-touchdown calls; the second T-38 provided live TV and back-up. Modifications included extension of the landing gear extension speed, increasing the area of the speedbrakes, and installation of a TV system; the goal was to stay with the Shuttle below 40,000 ft while it descended at 15,000 ft/min. Ten T-38's were modified and the deployment of lead and back-up crews during the first Shuttle flight is outlined. Western Test Range C-band radar data of the Orbiter position were transformed into intercept coordinates and VHF relayed to the chase craft. Photographs were taken of the right and left sides and underside of the Shuttle while flying with the speedbrake up to match the Shuttle speed.

Mcbride, J. A.↗
NASA NTRS1989

Static internal performance of a nonaxisymmetric vaned thrust reverser with flow splay capability

An investigation was conducted in the Static Test Facility of the Langley 16-Foot Transonic Tunnel on a dual-port, nonaxisymmetric, block-and-turn type thrust reverser model with vane cascades in the reverser ports which turned the flow in the splay direction and aided in turning the flow in the reverse direction. Splaying reverser flow is a method of delaying to lower landing ground roll speeds the reingestion of hot exhaust flow into the inlets. Exhaust flow splay can also help prevent the impingement of hot exhaust gases on the empennage surfaces when the reverser is integrated into an actual airframe. The vane cascades consisted of two sets of perpendicular vanes with a variable number of turning and splay vanes. A skewed vane box was also tested which had only one set of vanes angled to provide both turning and splay. Vane cascades were designed to provide different amounts of flow splay in the top and bottom ports. Inner doors, trim tabs, and an orifice plate all provided means of varying the port area for reverser flow modulation. The outer door position was varied as a means of influencing the flow reverse angle. Nozzle pressure ratio was varied from 1.75 to approximately 6.00.

Bangert, Linda S.↗
NASA NTRS1920

Notes on specifications for French airplane competitions

Given here are the rules officially adopted by the Aeronautical Commission of the Aero Club of France for a flight competition to be held in France in 1920 at the Villacoublay Aerodrome. The prize will be awarded to the pilot who succeeds in obtaining the highest maximum and lowest minimum speeds, and in landing within the shortest distance.

Margoulis, W↗
NASA NTRS1942

The Longitudinal Stability of Flying Boats as Determined by Tests of Models in the NACA Tank II : Effect of Variations in Form of Hull on Longitudinal Stability

Data taken from tests at constant speed to establish trim limits of stability, tests at accelerated speeds to determine stable limits of center of gravity shift, and tests at decelerated speeds to obtain landing characteristics of several model hull forms were used to establish hull design effect on longitudinal stability of porpoising. Results show a reduction of dead rise angle as being the only investigated factor reducing low trim limit. Various methods of reducing afterbody interference increased upper trim limit

Olson, Roland E.↗
NASA NTRS2019

Predicting Jet Noise for Full-Scale Low-Boom Aircraft

Supersonic vehicle research addresses the development of tools, technologies, and knowledge to help eliminate technical barriers to practical commercial supersonic flight. While the major focus of this research has been on reducing the ground signature at supersonic cruise, airplanes must also satisfy noise constraints during takeoff and landing at subsonic speeds, and jet noise is the main sound source. We use computational aeroacoustic sim- ulation tools to assess new designs at these lower speeds. We are further scrutinizing both modeling and simulation practices and the use of hybrid Reynolds-averaged Navier Stokes/Large- Eddy Simulations methods and developing new methods to predict jet noise on a full flight configuration.

Stich, Gerrit-Daniel↗