SEARCH · Search NASA

Results for “LOAD FACTOR”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

All sources NASA NTRS DOE OSTI

NASA NTRS1979

Precision controllability of the F-15 airplane

A flying qualities evaluation conducted on a preproduction F-15 airplane permitted an assessment to be made of its precision controllability in the high subsonic and low transonic flight regime over the allowable angle of attack range. Precision controllability, or gunsight tracking, studies were conducted in windup turn maneuvers with the gunsight in the caged pipper mode and depressed 70 mils. This evaluation showed the F-15 airplane to experience severe buffet and mild-to-moderate wing rock at the higher angles of attack. It showed the F-15 airplane radial tracking precision to vary from approximately 6 to 20 mils over the load factor range tested. Tracking in the presence of wing rock essentially doubled the radial tracking error generated at the lower angles of attack. The stability augmentation system affected the tracking precision of the F-15 airplane more than it did that of previous aircraft studied.

Sisk, T. R.↗

NASA NTRS1978

Comparative evaluation of distributed-collector solar thermal electric power plants

Distributed-collector solar thermal-electric power plants are compared by projecting power plant economics of selected systems to the 1990-2000 timeframe. The approach taken is to evaluate the performance of the selected systems under the same weather conditions. Capital and operational costs are estimated for each system. Energy costs are calculated for different plant sizes based on the plant performance and the corresponding capital and maintenance costs. Optimum systems are then determined as the systems with the minimum energy costs for a given load factor. The optimum system is comprised of the best combination of subsystems which give the minimum energy cost for every plant size. Sensitivity analysis is done around the optimum point for various plant parameters.

Fujita, T.↗

NASA NTRS1979

A flight investigation of performance and loads for a helicopter with NLR-1T main-rotor blade sections

Data on performance and rotor loads for a teetering-rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade-section contour are presented. The test envelope included hover, forward-flight speed sweeps from 35 to 85 m/sec, and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point described vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗

NASA NTRS1979

Flight-measured afterbody pressure coefficients from an airplane having twin side-by-side jet engines for Mach numbers from 0.6 to 1.6

Afterbody pressure distribution data were obtained in flight from an airplane having twin side-by-side jet exhausts. The data were obtained in level flight at Mach numbers from 0.60 to 1.60 and at elevated load factors for Mach numbers of 0.60, 0.90, and 1.20. The test altitude varied from 2300 meters (7500 feet) to 15,200 meters (50,000 feet) over a speed range that provided a matrix of constant Mach number and constant unit Reynolds number test conditions. The results of the full-scale flight afterbody pressure distribution program are presented in the form of plotted pressure distributions and tabulated pressure coefficients with Mach number, angle of attack, engine nozzle pressure ratio, and unit Reynolds number as controlled parameters.

Steers, L. L.↗

NASA NTRS1980

Precision controllability of the YF-17 airplane

A flying qualities evaluation conducted on the YF-17 airplane permitted assessment of its precision controllability in the transonic flight regime over the allowable angle of attack range. The precision controllability (tailchase tracking) study was conducted in constant-g and windup turn tracking maneuvers with the command augmentation system (CAS) on, automatic maneuver flaps, and the caged pipper gunsight depressed 70 mils. This study showed that the YF-17 airplane tracks essentially as well at 7 g's to 8 g's as earlier fighters did at 4 g's to 5 g's before they encountered wing rock. The pilots considered the YF-17 airplane one of the best tracking airplanes they had flown. Wing rock at the higher angles of attack degraded tracking precision, and lack of control harmony made precision controllability more difficult. The revised automatic maneuver flap schedule incorporated in the airplane at the time of the tests did not appear to be optimum. The largest tracking errors and greatest pilot workload occurred at high normal load factors at low angles of attack. The pilots reported that the high-g maneuvers caused some tunnel vision and that they found it difficult to think clearly after repeated maneuvers.

Sisk, T. R.↗

NASA NTRS1980

Navigation network operational considerations

The development of the philosphy necessary for the initial operations costing of the three candidate navigation network designs is described. The effect of the need to minimize costs upon the operations and maintenance concepts, the simplification of operations by adopting the very long base interferometry principle as a basis for the scenarios, and the estimation of the annual load factor based upon an assumed mission set are detailed.

Hird, E.↗

NASA NTRS1980

A flight investigation of performance and loads for a helicopter with 10-64C main rotor blade sections

A flight investigation produced data on performance and rotor loads for a teetering rotor, AH-1G helicopter flown with a main rotor that had the NLR-1T airfoil as the blade section contour. The test envelope included hover, forward flight speeds from 34 to 83 m/sec (65 to 162 knots), and collective fixed maneuvers at about 0.25 tip speed ratio. The data set for each test point describes vehicle flight state, control positions, rotor loads, power requirements, and blade motions. Rotor loads are reviewed primarily in terms of peak to peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor. Detailed data for an advanced airfoil on an AH-1G are presented.

Morris, C. E. K.↗

NASA NTRS1980

A flight investigation of performance and loads for a helicopter with RC-SC2 main-rotor blade sections

The test envelope included hover, forward-flight speed sweeps from 33 to 74 m/sec (65 to 144 knots), and collective-fixed maneuvers at about 0.25 tip-speed ratio. The data set for each test point describes vehicle flight states, control positions, rotor loads, power requirements and blade motions. Rotor loads were reviewed primarily in terms of peak-to-peak and harmonic content. Lower frequency components predominated for most loads and generally increased with increased airspeed, but not necessarily with increased maneuver load factor.

Morris, C. E. K., Jr.↗

NASA NTRS1980

Concorde with the airlines

The only supersonic aircraft in airline service, Concorde, offers the first actual test of supersonic cruise feasibility and the only real experience relative to passenger, airline, and community acceptance. The dominant characteristic of Concorde operations is low aircraft utilization, due partly to the restricted route network. Operating costs, the maintenance/reliability record and associated dispatch delays are discussed. Problems with overwater operations, and the secondary boom phenomena are examined. Monthly average load factors for various routes, major causes of technical delays, aircraft technical performance, and aircraft tracks are graphically depicted.

Leyman, C. S.↗

NASA NTRS1981

Kinematic properties of rotary-wing and fixed-wing aircraft in steady coordinated high-g turns

An analytical approach to the study of flight dynamics of aircraft operating in a high-angle-of-attack flight regime and of helicopters operating in extreme thrust conditions is presented. Steady coordinated high-g turns are used to establish the initial equilibrium flight conditions near stall angles of attack. The kinematic properties of the aircraft in steady coordinated turns are examined: in high-g turns, pitch rate (independent of the angle of attack) is of a much larger magnitude than roll and yaw rate; a substantial roll rate is found to develop in steep turns for all angles of attack; the angle of attack also has a significant effect on the pitch attitude, with decreasing influence as the normal load factor increases. The exact small disturbance equations of motion of the aircraft in general steady turns are also developed for application to both rotary-wing and fixed-wing aircraft in extreme conditions. These equations are in a first-order, vector-matrix format, and are thus compatible with many efficient software packages developed in modern system theory.

Chen, R. T. N.↗

NASA NTRS1982

Spin tests of a single-engine, high-wing light airplane

The airplane has a relatively steep spin mode (low angle of attack) with a high load factor and high velocity. The airplane recovers almost immediately after any deviation from the prospin control positions, except for one maneuver with reduced flexibility in the elevator control system.

Stewart, E. C.↗

NASA NTRS1982

Influence of maneuverability on helicopter combat effectiveness

A computational procedure employing a stochastic learning method in conjunction with dynamic simulation of helicopter flight and weapon system operation was used to derive helicopter maneuvering strategies. The derived strategies maximize either survival or kill probability and are in the form of a feedback control based upon threat visual or warning system cues. Maneuverability parameters implicit in the strategy development include maximum longitudinal acceleration and deceleration, maximum sustained and transient load factor turn rate at forward speed, and maximum pedal turn rate and lateral acceleration at hover. Results are presented in terms of probability of skill for all combat initial conditions for two threat categories.

Falco, M.↗

NASA NTRS1981

An investigation of the use of a propulsive wing/canard concept for improved maneuvering

The propulsive wing concept is an extension of the flap boundary layer control utilized on several aircraft configurations. Several studies have been made regarding the benefits of the propulsive wing in STOL operation. However, the propulsive wing/canard provides performance benefits also in areas other than STOL. It is expected to improve the maneuvering capability by providing reduced drag at high lift coefficients without appreciably affecting the low lift drag. An increase in the buffet free load factor can also be expected with the blown wing and canard. Attention is given to a program to investigate the wing/canard at maneuvering conditions, and tests at ranges of blowing coefficients equivalent to STOL operation.

Stewart, V. R.↗

NASA NTRS1981

Optimal maneuvers at supersonic speeds in a vertical plane

This paper presents several optimal maneuvers of supersonic aircraft in a vertical plane. The general dimensionless equations of motion are derived and the computation of the optimal trajectories are carried out using the aerodynamics and engine characteristics of a light-weight fighter called the supercruiser. Because of the normalizing of the control variables, namely, the load factor and the thrust-to-weight ratio, the results applied to any supersonic aircraft. The optimality of the singular thrust control and the optimal junction of different subarcs are discussed. The proposed method of computing the optimal trajectory is very efficient and makes explicit the selection of the optimal control. The technique should be useful for performance assessment of supersonic aircraft with potential for implementation of onboard flight control system.

Vinh, N. X.↗

NASA NTRS1982

Performance analysis of digital integrate-and-dump filters

Key design parameters associated with the operation of a digital integrate-and-dump filter are identified in this paper. Performance degradation effects associated with the selection of these parameters such as analog-to-digital converter (ADC) gain loading factor, number of bits used, predetection bandwidth, sampling rate, and accumulator length are considered. Numerical results of practical interest are also provided.

Chie, C. M.↗

NASA NTRS1982

Measurement and evaluation of swirl-type flow in labyrinth seals of conventional turbine stages

The effects of load factor and rotor eccentricity were determined on flow conditions in test series for two stages. The results indicate that swirl-type entry flow follows the rules of potential swirl. Within the labyrinth cavities two spatial separated flow areas are considered. A dominating flow in periphera direction nearly fills the space between the sealing strips and the ceiling of the cavity. Below this flow, an area of axial mass transport is situated, with a slight peripheral component, limited on the nearest surroundings of the seals gap and the rotor surface. Between both flows, an exchange of energy takes place. Within the gaps, flow direction depends on axial velocity and therefore on variable flow contraction. A balance of energy within the seal and the cavities interprets the results of lateral force measurements as an influence of friction at the sealing strips surface and the rotating shaft surface. Stages with their blades put together in buckets by means of shrouding segments are particularly influenced by the rotating speed of the shrouding.

Hauck, L.↗

NASA NTRS1982

Performance and load data from Mod-0A and Mod-1 wind turbine generators

Experimental data, together with supporting analysis, are presented on the power conversion performance and blade loading of large, horizontal-axis wind turbines tested at electric utility sites in the U.S. Four turbine rotor configurations, from 28 to 61 meters in diameter, and data from five test sites are included. Performance data are presented in the form of graphs of power and system efficiency versus free-stream wind speed. Deviations from theoretical performance are analyzed statistically. Power conversion efficiency averaged 0.34 for all tests combined, compared with 0.31 predicted. Round blade tips appeared to improve performance significantly. Cyclic blade loads were normalized to develop load factors which can be used in the design of rotors with rigid hubs.

Spera, D. A.↗

NASA NTRS1983

Comparison of spur gear efficiency prediction methods

The predictions of five spur-gear efficiency calculation methods were compared with three sets of test data using different gear geometries. The data and the analysis methods were limited to jet lubricated, ground, spur gears. The data covered a range in pitch line velocity to 1 to 20 m/sec (200 to 4000 ft/min) and K-load factor range of 17 to 1600.

Anderson, N. E.↗