Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS, MANEUVERING - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2019

Verification of a Motion Cueing Strategy for Stall Recovery Training in a Commercial Transport Simulator

This paper verifies a motion cueing strategy for improved pilot stall recovery training in commercial transport simulators. Eight airline transport pilots flew a high-altitude stall recovery task in the NASA B747 level-D-certified full flight simulator under three different motion configurations: no motion, baseline motion, and enhanced motion. For each motion condition, pilots performed the task with both baseline aircraft dynamics and aircraft dynamics enhanced with lateral-directional characteristics of the airplane at angle of attack approaching stall. Motion configuration significantly affected: 1) pilot opinions on the helpfulness of motion in performing the task, 2) the maximum roll angle in the stall maneuver, 3) the minimum load factor in the recovery, 4) the number of secondary stick shakers in the stall recovery, and 5) the maximum airspeed in the recovery. The two different aircraft dynamics significantly affected: 1) pilot opinions on the noticeability of the banking roll off near the stall and 2) the maximum roll angle in the stall maneuver. These results indicate that the relatively minor enhancements to the motion logic of heritage commercial transport simulators presented here can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

Pilot Performance↗
NASA NTRS1991

Development and evaluation of an inverse solution technique for studying helicopter maneuverability and agility

An inverse solution technique for determining the maximum maneuvering performance of a helicopter using smooth, pilotlike control inputs is presented. Also described is a pilot simulation experiment performed to investigate the accuracy of the solution resulting from this technique. The maneuverability and agility capability of the helicopter math model was varied by varying the pitch and roll damping, the maximum pitch and roll rate, and the maximum load-factor capability. Three maneuvers were investigated: a 180-deg turn, a longitudinal pop-up, and a lateral jink. The inverse solution technique yielded accurate predictions of pilot-in-the-loop maneuvering performance for two of the three maneuvers.

Whalley, Matthew S.↗
NASA NTRS1971

Altered susceptibility to motion sickness as a function of subgravity level

Large interindividual differences among 74 normal subjects in the change in susceptibility to motion sickness with effective lifting of the normal g-load by parabolic flight maneuvers were recorded with high test-retest reliability. Most subjects, who were required to make standardized head movements while seated in a chair rotating at a constant speed, demonstrated either a substantial increase or a decrease in susceptibility, in confirmation of a previous study, while a few appeared to be more or less unaffected by the 1 g to 0 g gravitational change. A similar test procedure conducted with eighteen of the subjects at lunar- and Martian-gravity levels revealed further interindividual differences in susceptiblity as a function of g-level. The subjects with gravity-dependent susceptibility revealed: (1) a progressive change in susceptibility as a function of g-load in either the positive or negative direction that was characteristic of the individual, (2) a susceptibility level that appeared to be maintained at the fractional g-load, and (3) immunity to motion sickness at all g-levels tested below the earth standard. The case history as well as ground-based functional and provocative tests of normal subjects proved to be inadequate in predicting susceptibility to motion sickness under subgravity conditions.

Miller, E. F., II↗
NASA NTRS1973

Altered susceptibility to motion sickness as a function of subgravity level.

Large interindividual differences among 74 normal subjects in the change in susceptibility to motion sickness with effective lifting of the normal g-load by parabolic flight maneuvers were recorded with high test-retest reliability. Most subjects, who were required to make standardized head movements while seated in a chair rotating at a constant speed, demonstrated either a substantial increase or a decrease in susceptibility, in confirmation of a previous study, while a few appeared to be more or less unaffected by the 1 g to 0 g gravitational change. A similar test procedure conducted with eighteen of the subjects at lunar- and Martian-gravity levels revealed further interindividual differences in susceptibility as a function of g-level.

Miller, E. F., II↗
NASA NTRS1975

Digital command system

The correct processing of the Digital Command System (DCS), which provides a limited real-time means of controlling specific flight program functions, was verified. The ability of the flight program to correctly read and process DCS commands was verified. Tests made by the flight program after reading the contents of the command decoder register to establish the validity of the received data were verified through the following: DCS mode command verification, DCS data command verification, DCS data validation, and DCS error message. The operation of the following DCS commands accepted and processed by the flight program was tested: time base update, navigation update, generalized switch selector, memory dump, terminate, execute generalized maneuver, return to nominal timeline, ECS water control valve logic inhibit, execute maneuver, execute alternate sequence, targeting load, ladder magnitude limit, S-IVB/IU de-orbit, compressed data dump, and remove inhibit on the extraction maneuver.

Source record↗
NASA NTRS1976

Utilization of solid-propellant upper stages in STS payload orbital operations

The main purpose of this report is to discuss techniques of trajectory design, maneuver execution, and stage loading that are compatible with the use of SRM's (solid rocket motors) which, once ignited, must burn to propellant depletion. It is anticipated that some shuttle payloads will use non-IUS (interim upper stage) solid propellant kick stages; therefore this subject is also pertinent to shuttle flights other than those involving the use of the IUS. The SRM utilization techniques can be divided into two major categories: (1) those in which the stage performance is adjusted to match the velocity increment magnitude requirements of a preselected trajectory, and (2) those in which the trajectory is designed to match the velocity increment magnitude capability of the stage(s).

Wilson, S. W.↗
NASA NTRS1998

Optimization of Supersonic Transport Trajectories

This paper develops a near-optimal guidance law for generating minimum fuel, time, or cost fixed-range trajectories for supersonic transport aircraft. The approach uses a choice of new state variables along with singular perturbation techniques to time-scale decouple the dynamic equations into multiple equations of single order (second order for the fast dynamics). Application of the maximum principle to each of the decoupled equations, as opposed to application to the original coupled equations, avoids the two point boundary value problem and transforms the problem from one of a functional optimization to one of multiple function optimizations. It is shown that such an approach produces well known aircraft performance results such as minimizing the Brequet factor for minimum fuel consumption and the energy climb path. Furthermore, the new state variables produce a consistent calculation of flight path angle along the trajectory, eliminating one of the deficiencies in the traditional energy state approximation. In addition, jumps in the energy climb path are smoothed out by integration of the original dynamic equations at constant load factor. Numerical results performed for a supersonic transport design show that a pushover dive followed by a pullout at nominal load factors are sufficient maneuvers to smooth the jump.

Ardema, Mark D.↗
NASA NTRS1998

Development of Advanced Methods of Structural and Trajectory Analysis for Transport Aircraft

This paper develops a near-optimal guidance law for generating minimum fuel, time, or cost fixed-range trajectories for supersonic transport aircraft. The approach uses a choice of new state variables along with singular perturbation techniques to time-scale decouple the dynamic equations into multiple equations of single order (second order for the fast dynamics). Application of the maximum principle to each of the decoupled equations, as opposed to application to the original coupled equations, avoids the two point boundary value problem and transforms the problem from one of a functional optimization to one of multiple function optimizations. It is shown that such an approach produces well known aircraft performance results such as minimizing the Brequet factor for minimum fuel consumption and the energy climb path. Furthermore, the new state variables produce a consistent calculation of flight path angle along the trajectory, eliminating one of the deficiencies in the traditional energy state approximation. In addition, jumps in the energy climb path are smoothed out by integration of the original dynamic equations at constant load factor. Numerical results performed for a supersonic transport design show that a pushover dive followed by a pullout at nominal load factors are sufficient maneuvers to smooth the jump.

Ardema, Mark D.↗
NASA NTRS2001

Aeroelastic Stability of A Soft-Inplane Gimballed Tiltrotor Model In Hover

Soft-inplane rotor systems can significantly reduce the inplane rotor loads generated during the maneuvers of large tiltrotors, thereby reducing the strength requirements and the associated structural weight of the hub. Soft-inplane rotor systems. however, are subject to instabilities associated with ground resonance, and for tiltrotors this instability has increased complexity as compared to a conventional helicopter. Researchers at Langley Research Center and Bell Helicopter-Textron, Inc. have completed ail initial study of a soft-inplane gimballed tiltrotor model subject to ground resonance conditions in hover. Parametric variations of the rotor collective pitch and blade root damping, and their associated effects oil the model stability were examined. Also considered in the study was the effectiveness of ail active swash-plate and a generalized predictive control (GPC) algorithm for stability augmentation of the ground resonance conditions. Results of this study show that the ground resonance behavior of a gimballed soft-inplane tiltrotor can be significantly different from that of a classical soft-inplane helicopter rotor. The GPC-based active swash-plate was successfully implemented, and served to significantly augment damping of the critical modes to an acceptable value.

Nixon, Mark W.↗
NASA NTRS2001

Aeroelastic Stability of a Soft-Inplane Gimballed Tiltrotor Model in Hover

Soft-inplane rotor systems can significantly reduce the inplane rotor loads generated during the maneuvers of large tiltrotors, thereby reducing the strength requirements and the associated structural weight of the hub. Soft-inplane rotor systems, however, are subject to instabilities associated with ground resonance, and for tiltrotors this instability has increased complexity as compared to a conventional helicopter. Researchers at Langley Research Center and Bell Helicopter-Textron, Inc. have completed an initial study of a soft-inplane gimballed tiltrotor model subject to ground resonance conditions in hover. Parametric variations of the rotor collective pitch and blade root damping., and their associated effects on the model stability were examined. Also considered in the study was the effectiveness of an active swashplate and a generalized predictive control (GPC) algorithm for stability augmentation of the ground resonance conditions. Results of this study show that the ground resonance behavior of a gimballed soft-inplane tiltrotor can be significantly different from that of a classical soft-inplane helicopter rotor. The GPC-based active swashplate was successfully implemented, and served to significantly augment damping of the critical modes to an acceptable value.

Nixon, Mark W.↗
NASA NTRS2008

Optimization of Angular-Momentum Biases of Reaction Wheels

RBOT [RWA Bias Optimization Tool (wherein RWA signifies Reaction Wheel Assembly )] is a computer program designed for computing angular momentum biases for reaction wheels used for providing spacecraft pointing in various directions as required for scientific observations. RBOT is currently deployed to support the Cassini mission to prevent operation of reaction wheels at unsafely high speeds while minimizing time in undesirable low-speed range, where elasto-hydrodynamic lubrication films in bearings become ineffective, leading to premature bearing failure. The problem is formulated as a constrained optimization problem in which maximum wheel speed limit is a hard constraint and a cost functional that increases as speed decreases below a low-speed threshold. The optimization problem is solved using a parametric search routine known as the Nelder-Mead simplex algorithm. To increase computational efficiency for extended operation involving large quantity of data, the algorithm is designed to (1) use large time increments during intervals when spacecraft attitudes or rates of rotation are nearly stationary, (2) use sinusoidal-approximation sampling to model repeated long periods of Earth-point rolling maneuvers to reduce computational loads, and (3) utilize an efficient equation to obtain wheel-rate profiles as functions of initial wheel biases based on conservation of angular momentum (in an inertial frame) using pre-computed terms.

Lee, Clifford↗
NASA NTRS1977

Load and stability measurements on a soft-inplane rotor system incorporating elastomeric lead-lag dampers

An experimental investigation was conducted of the dynamic response and inplane stability associated with a new soft-inplane helicopter rotor. The unique feature of this rotor was the use of an internal elastomeric damper to restrain the blade inplane motion about the lead-lag hinge. The properties of the elastomer were selected to provide both a nominal first inplane frequency ratio of 0.65 and sufficient damping to eliminate the need for additional external damping sources to prevent ground resonance on a typical fuselage structure. For this investigation a 1/5-scale aeroelastic model was used to represent the rotor. The four-blade model had a diameter of 3.05 m (10 ft) and a solidity of 0.103. The first out-of-plane frequency ratio was 1.06. The model was tested in hover and in forward flight up to an advance ratio of 0.45. At each forward speed the rotor lift was varied up to simulated maneuver conditions. The measured rotor loads and response were within acceptable limits, and no adverse response qualities were observed. Moderate out-of-plane hub moments were measured, even for zero lift, to indicate the beneficial control power available for this design. Blade inplane stability testing indicated that the rotor system damping remained at moderate levels throughout the operating envelope.

Weller, W. H.↗
NASA NTRS2006

Integrated Modeling of Advanced Opto-Mechanical Systems

The design of optical hardware for space applications is particularly challenging when developing high performance, novel systems that have no precedent. Integrated modeling and analysis of such opto-mechanical systems seeks to describe the end-to-end performance of the hardware using mission-relevant metrics. This multidisciplinary analysis might start with thermal disturbances from observation maneuvers, compute the system temperatures, compute the distorted positions and shapes of the hardware and compute the resulting optical performance. Dynamic disturbances such as reaction wheel imbalance or inertia imbalance of optical delay lines might be applied to a structural dynamic model and used in a guidance and control analysis. Mission-relevant science metrics might include wavefront quality, pointing error or imaging stability. Assembling a tool chain that can be both nimble and effective when scaled to the high fidelity models of detail design has been challenging. An integrated thermal, mechanical and optical analysis capability suitable for detail design has been developed and verified through experimental measurement. This capability was used in the design of flight-like breadboard hardware and development of a test apparatus that established both the level of performance of the hardware and the validity of the analysis. The analysis includes prediction of the thermal environment of the test chamber, detailed temperature distributions on the breadboard hardware, fine scale deformations of the optical elements, and computation of the wavefront quality using geometric optics. A battery of tests were conducted to assess the experiment data acquisition, measurement and control system and to establish the performance of the hardware design and accuracy of the integrated modeling. Thermal loads that represent operational observing maneuvers were imposed and the hardware optical performance was measured and compared to analytical predictions.

optomechanical analysis↗
NASA NTRSDate not supplied

Aerocapture Solutions for Uranus Flagship-class Orbiter and Probe

Recent planetary mission assessments, such as the 2022 Planetary Science Decadal Survey released by the National Academies of Science, have focused on the need for a flagship-class mission to the Ice Giant planets, particularly Uranus. The Uranus Orbit and Probe mission proposal was used by the National Academies of Science as the baseline while making its recommendation as the top flagship-class mission for NASA in the 2020-2030\'s. This mission which was based on a launch date of 2031 or 2032, used a fully-propulsive orbit insertion maneuver at Uranus (requiring 60-70% of total mass for propellant), and reached the planet after 13 years of interplanetary cruise before the 2049 equinox, a goal of the science community. A pre-2033 launch date is required to conduct a necessary Jupiter fly-by as the giant planet will be not be in the proper alignment for a later launch date. However, as the budget constraints of the NASA budget have pushed back the start date of a Uranus mission, a launch date of a flagship mission before 2033 seems unreasonable. Aerocapture, an orbit insertion maneuver that uses the atmosphere to decelerate, can reduce the propellant load needed for a captured orbit. Additionally, the aerocapture maneuver can decelerate safely while approaching the planet at higher arrival velocities, thus allowing a mission to use a highly energetic trajectory and reduce the cruise time by several years. An aerocapture-enabled solution has launch opportunities in the mid 2030's, including as late as 2038 to reach Uranus by 2049. This paper will discuss the feasibility of an aerocapture option for a Flagship-class mission to Uranus.

Soumyo Dutta↗
NASA NTRSDate not supplied

Aerocapture Solutions for Uranus Flagship-class Orbiter and Probe

Recent planetary mission assessments, such as the 2022 Planetary Science Decadal Survey released by the National Academies of Science, have focused on the need for a flagship-class mission to the Ice Giant planets, particularly Uranus. The Uranus Orbit and Probe mission proposal was used by the National Academies of Science as the baseline while making its recommendation as the top flagship-class mission for NASA in the 2020-2030\'s. This mission which was based on a launch date of 2031 or 2032, used a fully-propulsive orbit insertion maneuver at Uranus (requiring 60-70% of total mass for propellant), and reached the planet after 13 years of interplanetary cruise before the 2049 equinox, a goal of the science community. A pre-2033 launch date is required to conduct a necessary Jupiter fly-by as the giant planet will be not be in the proper alignment for a later launch date. However, as the budget constraints of the NASA budget have pushed back the start date of a Uranus mission, a launch date of a flagship mission before 2033 seems unreasonable. Aerocapture, an orbit insertion maneuver that uses the atmosphere to decelerate, can reduce the propellant load needed for a captured orbit. Additionally, the aerocapture maneuver can decelerate safely while approaching the planet at higher arrival velocities, thus allowing a mission to use a highly energetic trajectory and reduce the cruise time by several years. An aerocapture-enabled solution has launch opportunities in the mid 2030's, including as late as 2038 to reach Uranus by 2049. This paper will discuss the feasibility of an aerocapture option for a Flagship-class mission to Uranus.

Soumyo Dutta↗
NASA NTRS1965

Beyond apollo.

Apollo capabilities extended for future biomedical, technological and operational experiments, trading space maneuvering capability for experiment load-carrying capacity

SPACE EXPLORATION↗