Search NASA⌕ Search

SEARCH · Search NASA

Results for “LOADS, STEADY - WINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Investigation of fouling mechanisms for diesel engine exhaust heat recovery

The effect of diesel engine exhaust fouling on heat and mass exchangers for waste heat recovery is investigated. Experiments are conducted for a range of operating conditions relevant to the use of the waste heat from a diesel engine for powering a 2.71 kW capacity absorption heat pump. Thermal resistances of fouling layers as well as their effects on pressure drop are determined, and the underlying mechanisms for deposition and removal are investigated. Fouling layer effects are most severe for the lowest coolant temperatures and 100% generator load. At these conditions, the fouling thermal resistance is approximately 70% of the total resistance, and the ratio of the steady-state pressure drop to the baseline pressure drop is 3.25. Flow induced shear is found to be the primary growth inhibiting mechanism at high exhaust velocities. Findings from this study can guide heat exchanger design for a variety of waste heat recovery systems.

04 OIL SHALES AND TAR SANDS↗
DOE OSTI2020

Validation of Combined Analytical Methods to Predict Slip in Cylindrical Roller Bearings

This paper presents a combination of models that together calculate the cage and roller speeds of a cylindrical roller bearing. The models consider elastohydrodynamic lubrication and contact elasticity between the roller and raceway, roller centrifugal forces, hydrodynamic lubrication at the cage pocket, and frictional forces. Using these models, the predicted cage and roller speeds and the extent of slip are compared to measurements acquired on cylindrical roller bearings in a commercial gearbox in steady-state and transient operating conditions of a wind turbine. In steady-state conditions at low wind speeds and low lubricant temperatures, cage and roller slip up to 60% occur in the loaded zone of the bearing. In the unloaded zone, up to 80% roller slip occurs. Cage and roller slip then decrease as the lubricant temperature and wind speed increases. In general, the analytical model results match experimental measurements within 10% for lubricant temperatures above 40 degrees C and wind speeds over 10 meters per second. The analytical model is further evaluated during a transient start-up event and highly dynamic emergency stop event and also used to examine changes in the bearing design or lubricant properties. Furthermore, roller and cage slip in cylindrical bearings is a combined effect of the bearing design, applied load, shaft speed, and lubricant properties and temperature, and can be quickly evaluated with the combined analytical models.

17 WIND ENERGY↗
DOE OSTI2026

Durable Thin‐Film Porous Transport Electrodes for High Current Density PEM Water Electrolysis

Proton exchange membrane water electrolyzers rely on relatively expensive Ir-based catalysts for efficient and durable hydrogen production. To reduce system costs, Ir loadings can be reduced if performance and durability are maintained. Sputter deposition is a readily scalable method to synthesize uniform, low-loading catalyst layers with controlled composition. A catalyst applied directly to the porous transport layer can have advantages for performance, manufacturing simplicity, and catalyst recovery. Suitable porous transport layer porosity can minimize activity losses when reducing loadings. Here, methods are presented to deposit metallic Ir as well as amorphous and rutile Ir oxides. The activity and durability of these materials in the porous transport electrode architecture is evaluated. The metallic and amorphous forms have better initial activity, however, operation at 3 A cm −2 with 0.1 mg Ir cm −2 shows that only rutile IrO 2 maintains performance beyond 100 h with a 50 mV improvement after 700 h. A >10x reduced dissolution rate is shown for rutile IrO 2 . With a low-porosity transport layer and 0.4 mg Ir cm −2 , a steady-state voltage decay rate of 6 µV h −1 is achieved. The results demonstrate that sputter-deposited rutile IrO 2 porous transport electrodes with low Ir loading can be operated at high current density to reduce hydrogen production costs.

08 HYDROGEN↗
DOE OSTI2023

Impact of Soret effect on hydrogen and helium retention in PFC tungsten under ELM-like conditions

Abstract In our previous work, we have demonstrated using nonequilibrium molecular-dynamics simulations that the fluxes of helium and self-interstitial atoms in the presence of a thermal gradient in tungsten are directed opposite to the heat flux, indicating that species transport is governed by a Soret effect, namely, thermal-gradient-driven diffusion, characterized by a negative heat of transport that drives species transport uphill, i.e. from the cooler to the hot regions of the tungsten sample. In this work, the findings of our thermal and species transport analysis have been implemented in our cluster-dynamics code, Xolotl, which has been used to compute temperature and species profiles over spatiotemporal scales representative of plasma-facing component (PFC) tungsten under typical reactor operating conditions, including extreme heat loads at the plasma-facing surface characteristic of plasma instabilities that induce edge localized modes (ELMs). We demonstrate that the steady-state species profiles, when properly accounting for the Soret effect, vary significantly from those where temperature-gradient-driven transport is not accounted for and discuss the implications of such a Soret effect on the response to plasma exposure of plasma-facing tungsten. Although our cluster-dynamics simulations do not yet include self-clustering of helium or hydrogen blister formation, our simulation results show that the Soret effect substantially reduces helium and hydrogenic species retention inside PFC tungsten.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Multifunctional Catalysts for the Tandem Reactions of Oxygenates

Industrially-relevant catalytic reactions rarely consist of a simple sequence of elementary steps. Moreover, kinetic coupling of multiple reactions on a catalyst surface is highly desired for process intensification and improved energy efficiency for large scale chemical transformations. The shifting landscape of hydrocarbon chemical feedstocks in the US also motivates research on the selective conversion of more complex molecules. One desirable type of catalytic reaction is the reduction of carboxylic acids that are produced from biomass feedstocks to their corresponding alcohols. The proposed research explores the fundamental importance of hydrogen spillover on a multifunctional catalyst for carboxylic acid reduction with H 2 composed of metal particles coupled to metal oxide particles. Recent work has demonstrated the excellent performance of supported tungsten oxide clusters for carboxylic acid reduction, but only after they are promoted with a late transition metal such as palladium. Elucidating the active state of the catalyst and the associated reaction mechanism for acid reduction on that active state are the overall goals of the proposed project and successful completion will enable future design of efficient multifunctional catalysts. The critically important role of the metal promoter is hypothesized to be its ability to dissociate H2 and spillover atomic H to the support. Although hydrogen spillover is a well-recognized phenomenon in catalysis, its role in both catalyst activation and catalytic turnover are still unresolved. The study combined materials synthesis, characterization, reactivity testing, and molecular simulations, to explore the effect of hydrogen chemical potential on the formation of the active catalytic sites and on the steady state catalytic reduction of carboxylic acid. Varying the hydrogen chemical potential through modification of the gas conditions, support composition, and metal loading to modulated the structure and catalytic performance of the reducible metal oxide. Dual function catalysts containing supported Pd and WO x species co-located on a non-reducible carrier (silica) and a reducible carrier (titania) were synthesized and characterized by electron microscopy, temperature-programmed reduction, and chemisorption. Spectroscopic methods such as X-ray absorption and UV-vis were also used to evaluate the catalysts, which were used in the reduction of propionic acid to aldehyde and alcohol. Quantum chemical calculations, including ab initio phase diagrams provided molecular insights into the H spillover phenomenon.

09 BIOMASS FUELS↗
DOE OSTI2026

Analytic Expressions for Extracting Far Scrape-Off Layer Transport Coefficients from the Plasma-Wall Interaction of Divertor Tokamaks

Magnetic-confinement DT pilot plants and DEMO-class devices will employ thin breeding blanket first walls with substantially lower steady-state power-handling margins than ITER-like thick walls, making reliable prediction of main-chamber particle and heat loads increasingly critical. This report addresses that need by developing analytic tools to interpret far scrape-off layer (far-SOL) plasma–wall interaction measurements in divertor tokamaks, with the goal of extracting effective cross-field transport coefficients from “window-frame” experiments and related diagnostics.

Stangeby, P. C. [Univ. of Toronto, ON (Canada)]↗
DOE OSTI2021

Modeling and Control of Cascaded Bridgeless Multilevel Rectifier Under Unbalanced Load Conditions

The goal of this project is to model and control a novel unidirectional cascaded multilevel bridgeless rectifier as an active front end in medium and high voltage applications. This topology has many advantages over a conventional cascaded H-bridge rectifier, such as lower implementation cost, higher reliability, and greater flexibility with similar power quality.The steady-state mathematical model is used to develop a method for the voltage balancing of dc cells. Power factor analysis is discussed to achieve unity power factor using fully controlled hbridge cells. Power loss, efficiency, and cost comparison studies between the traditional cascaded H-Bridge converter and the proposed bridgeless converter demonstrate the advantages. A novel control strategy is proposed to achieve dc voltage balancing, fast and robust grid synchronization and power factor correction under unbalanced load conditions. Simulation and experimental results validate the models and control method.

Cascaded Bridgeless Rectifier, Power factor analys↗
DOE OSTI2024

Excessive charge, beam loading, and impedance collapse thresholds for a velvet emitter

Excess emission has been observed from velvet cathodes with total emission times >150 ns. In this diode experiment, we produce a sub-relativistic electron beam with the ability to consistently change γ from 1.2 to 1.5 and β = 0.5–0.75. Electron emission in this particular diode geometry requires electric fields >40 kV/cm. The current increases at steady rates >0.05 A/ns after the head of the pulse, indicating an expansion of the emission surface and reduction in the effective AK gap. Small transients of excess emission (or arcs) are consistently observed for current pulses exceeding 150 ns. The excess emission results in beam loaded levels ≥10 kV on the diode voltage. The effects described here are compounded as diode voltage is increased. The principal objective of these experiments is to quantify electric field emission thresholds, current ramps, excess emission delays, effective beam loading, and impedance collapse.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

A Reinforcement Learning Approach to Augment Conventional PID Control in Nuclear Power Plant Transient Operation

The ability of nuclear reactors to operate their power conversion cycles more flexibly will enhance their value to energy grids with variable pricing. Current nuclear control systems are typically classical controllers that are often based on proportional-integral-derivative (PID) control. This paper presents a method of augmenting the existing PID control for difficult transient operations in nuclear power plants using a reinforcement learning–derived feedforward signal applied in real time. The agents, which are trained on a test thermal load-following problem, are designed to improve steam generator outlet temperature control for a range of fast load-following scenarios covering ramp rates from 9%/min to 15%/min. Several reinforcement learning algorithms were initially investigated for the training of the feedforward agents with deep Q-learning (DQN) and proximal policy optimization (PPO) networks, which were found to be the most promising. The DQN controllers utilize discrete actions, giving them a better disturbance rejection at steady state but inconsistent response to initial temperature deviations. In contrast, PPO-trained agents, which take continuous actions except for a dead zone around zero, were shown to have the best combination of high disturbance rejection at steady state and good tracking of the desired temperature value. The ability of the PPO agent was also examined, with the average time of decision making found to be on the order of 1 ms. The fault properties of the controller under the loss of the reinforcement learning agent feedforward signal were also examined. The controller showed strong performance in situations of “no-signal” faults. but was less good at handling “stuck-at” faults, where the feedforward signal remains at a set value. In both cases, however, the PID was able to successfully maintain stability, eventually returning the system to a steady state. It is hoped that this work will allow for the proposed control architecture to be examined for more difficult control problems such that it may eventually be used to adapt existing nuclear plants for more aggressive load-following on grids of the future.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Design and Analysis of a Double Wall, Water Cooled Window for Accelerator Based Mo-99 Production

The electron accelerator based Mo-99 production technique requires the use of Rhodotrons to generate 38 MeV, 6.32 mA pulsed electron beams. The introduction of the pulsed beam structure has introduced fatigue concerns in the vacuum-helium windows that did not exist previously for electron beam production via linear accelerators. Previous analysis has shown that temperature fluctuations of approximately 100°C above and below the steady state operating temperature of ~500°C will occur within the windows. A water cooled window will eliminate this concern by reducing the primary mechanical stress due to the 300-psig helium pressure load as well as the secondary thermally induced stress. Although a water cooled window was considered years ago, the complexities of adding an additional water line was unattractive until now. A double wall, water cooled window has been designed and analyzed for this reason. The water cooled window design is shown to decrease the helium-side window temperature to as low as 125°C, while the vacuum-side window is maintained at 161°C at a water flow rate of 3.2 GPM. These low steady state temperatures reduce the thermal stress of the helium-side window significantly. Also, the primary mechanical stress has been reduced by roughly 50% due to the reduced pressure gradient across the helium-side window (150-psig water and 300-psig helium). Considering a Mo-99 production loss of roughly 1%, the water cooled window is a drastic improvement over the previous helium cooled designs and should be greatly considered for future upgrades and redesign.

43 PARTICLE ACCELERATORS↗
DOE OSTI2025

Mechanistic insights into N 2 O formation as a side product in NH 3 -SCR over small pore Cu-zeolites

Here, the present contribution provides clarity to N 2 O formation mechanisms and key influencing factors during low temperature NH 3 -SCR, with the goal of enabling the rational design of advanced SCR catalysts with low greenhouse gas impact. By studying more than 50 small pore Cu-exchanged zeolite SCR catalyst samples, including model catalysts synthesized in our laboratories and state-of-the-art industrial catalysts, we explored a wide range of factors affecting N 2 O formation. These factors included Cu loading, support Si/Al ratio, support topology, catalyst aging, reaction temperature and reactant feed composition effects. We probed N 2 O formation under both steady-state SCR, and during NH 4 NO 3 decomposition via temperature programmed desorption (TPD). Finally, we used DFT to probe energetics of possible N 2 O formation pathways. Based on these studies, we confirm that low temperature N 2 O formation occurs via multiple reaction pathways that all involve NH 4 NO 3 and are supported by Cu moieties that facilitate in-situ NO oxidation to NO 2 .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Initial Results on a New Light-Duty 2.7-L Opposed-Piston Gasoline Compression Ignition Multi-Cylinder Engine

Abstract Gasoline compression ignition (GCI) is a cost-effective approach to achieving diesel-like efficiencies with low emissions. The fundamental architecture of the two-stroke Achates Power Opposed-Piston (OP) Engine enables GCI by decoupling piston motion from cylinder scavenging, allowing for flexible and independent control of cylinder residual fraction and temperature leading to improved low-load combustion. In addition, the high peak cylinder pressure and noise challenges at high-load operation are mitigated by the lower brake mean effective pressure (BMEP) operation and faster heat release for the same pressure rise rate of the OP Engine. These advantages further solidify the performance benefits of the OP Engine and demonstrate the near-term feasibility of advanced combustion technologies, enabled by the opposed-piston architecture. This paper presents initial results from steady-state testing on a brand new 2.7-L OP GCI multi-cylinder engine (MCE) designed for light-duty truck applications. Successful GCI operation calls for a high compression ratio (CR), leading to higher combustion stability at low loads, higher efficiencies, and lower cycle HC + NOX emissions. Initial results show a cycle average brake thermal efficiency (BTE) of 31.7%, which is already greater than 11% conventional engines, after only ten weeks of testing. Emissions results suggest that Tier 3 Bin 160 levels can be achieved using a traditional diesel after-treatment system. Combustion noise was well controlled at or below the United States Council for Automotive Research limits. In addition, initial results on catalyst light-off mode with GCI are also presented.

Energy & Fuels↗
DOE OSTI2022

Supported molybdenum oxides for the aldol condensation reaction of acetaldehyde

The (retro-)aldol condensation reaction is an important chemical transformation in the upgrading of biomass-derived compounds into fuels and valuable specialty chemicals. In this study, we found that supported molybdenum oxide (MoO x ) catalysts were active and selective for the aldol condensation of acetaldehyde to crotonaldehyde under steady-state reactor conditions. Through a combination of transmission electron microscopy (TEM), ultraviolet–visible (UV–VIS) diffuse reflectance spectroscopy, Fourier transform infrared (FTIR) spectroscopy of adsorbed pyridine, and steady-state reactor testing, we determined that highly dispersed MoO x has a strong interaction with a γ-Al 2 O 3 support resulting in optimal catalyst performance at low weight loadings. In contrast, MoO x particles supported on SiO 2 have a weaker interaction with the support, resulting in a monotonic relationship between Mo loading and aldol condensation activity. The Lewis acid site density and strength are important parameters for predicting aldol condensation activity across all samples. The concentration of weak acid sites had a poor correlation with aldol condensation activity, most likely because these sites are too weak to activate acetaldehyde for the reaction. Medium and strong acid sites both had good correlations to aldol condensation activity. Results from X-ray absorption near edge structure (XANES) and acetaldehyde temperature programmed desorption (TPD) indicated that partially reduced MoO x was more active for aldol condensation, but pretreatment in reducing or oxidizing environments had no significant effect on steady-state catalytic activity. Finally, characterization of spent catalyst samples through temperature programmed oxidation (TPO) and thermogravimetric analysis (TGA) revealed that catalysts with high densities of strong acid sites tended to form more carbonaceous deposits on the surface over the course of the reaction.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Neutronics and Thermo-Fluids Simulation of Generic Pebble-Bed Fluoride-Salt-Cooled High-Temperature Reactor

The fluoride-salt-cooled high-temperature reactor (FHR) is one of the advanced reactors that has been attracting considerable interest from both the research community and the nuclear industry. To help facilitate the nuclear community's familiarity with the FHR, Kairos Power has developed a generic FHR (gFHR) benchmark. In the research performed here, this benchmark was used to assess innovative modeling methods that combine stochastic and deterministic computer codes to perform the design and analysis of the gFHR. Further, the Monte Carlo code Serpent 2 was used to generate few-group cross sections that were then used in the neutron diffusion and thermal-fluids code AGREE to perform full-core neutronics and thermal-fluids steady-state and transient core analysis. The Argonne National Laboratory code SAM was then used to model the gFHR system and to simulate the load-follow operation of the gFHR.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Overview of the results from divertor experiments with attached and detached plasmas at Wendelstein 7-X and their implications for steady-state operation

Abstract Wendelstein 7-X (W7-X), the largest advanced stellarator, is built to demonstrate high power, high performance quasi-continuous operation. Therefore, in the recent campaign, experiments were performed to prepare for long pulse operation, addressing three critical issues: the development of stable detachment, control of the heat and particle exhaust, and the impact of leading edges on plasma performance. The heat and particle exhaust in W7-X is realized with the help of an island divertor, which utilizes large magnetic islands at the plasma boundary. This concept shows very efficient heat flux spreading and favourable scaling with input power. Experiments performed to overload leading edges showed that the island divertor yields good impurity screening. A highlight of the recent campaign was a robust detachment scenario, which allowed reducing power loads even by a factor of ten. At the same time, neutral pressures at the pumping gap entrance yielded the particle removal rate close to the values required for stable density control in steady-state operation.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2025

Innovative duo-recombination layer design for effective hydrogen crossover mitigation in advanced MEAs for PEM water electrolyzers

Hydrogen crossover in proton exchange membrane water electrolyzers (PEMWEs) poses a safety hazard, reduces the overall efficiency, and limits the operational differential pressure range. Here, in this study, a membrane electrode assembly (MEA) with innovative Pt duo-recombination layer (DRL) design is developed by the unique reactive spray deposition technology (RSDT). The novel design comprises two thin RLs integrated within the volume of the membrane and has a total Pt loading of only 0.04 mg Pt cm −2 . Long-term durability test for over 3000 h is performed with as-fabricated MEA at steady-state conditions typical for an industrial hydrogen production system. The results from the durability test show that the newly developed DRL design effectively suppresses the H2 crossover to below 0.5 vol%. Furthermore, comprehensive post-test characterization of the MEA is performed and potential failure mechanisms in the Pt RLs observed during the durability test are identified and discussed in detail for the first time.

08 HYDROGEN↗
DOE OSTI2024

Analysis of Grid-Forming Inverter Controls for Grid-Connected and Islanded Microgrid Integration

Autonomous grid-forming (GFM) inverter testbeds with scalable platforms have attracted interest recently. In this study, a self-synchronized universal droop controller (SUDC) was adopted, tested, and scaled in a small network and a test feeder using a real-time simulation tool to operate microgrids without synchronous generators. We presented a novel GFM inverter control adoption to better understand the dynamic behavior of the inverters and their scalability, which can impact the distribution system (DS). This paper provides a steady-state and transient analysis of the GFM power inverter controller via simulation to better understand voltage and frequency stabilization and ensure that the critical electric loads are not affected during a prolonged power outage. The controllers of the GFM inverter are simulated in HYPERSIM to examine voltage and frequency fluctuations. This analysis includes assessing the black start capability for photovoltaic microgrids, both grid-connected and islanded, during transient fault conditions. The high photovoltaic PV penetration levels open exciting opportunities and challenges for the DS. The GFM inverter control demonstrated appropriate response times for synchronization, connection, and disconnection to the grid. The DS has become more resilient and independent of fossil fuels by increasing the penetration of inverter-based distributed energy resources (DERs).

Ward, Laura (ORCID:0000000345501581)↗