Search NASA⌕ Search

SEARCH · Search NASA

Results for “Li stability”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2026

Anode-less Solid-State Li–S Batteries Enabled by Fe-Stabilized Polysulfides

Anode-less solid-state lithium-sulfur batteries (SSLSBs) with lithium sulfide (Li 2 S) as the cathode promise a high energy density and ease of manufacturing. However, Li 2 S is plagued by poor conductivity, sluggish activation kinetics, and a poor cycle life. Here, in this study, we report an FeCl 3 -activated Li 2 S (FLS) cathode with solid-state polysulfide intermediates generated through a redox reaction between FeCl 3 and Li 2 S. This strategy is shown to boost the electrical conductivity of Li 2 S by 7 orders of magnitude and lower the activation barrier. During cycling, Fe plays a significant role in stabilizing the highly active polysulfide species, contributing to the exceptional electrochemical performance. The FLS cathode achieves 80% capacity retention over 500 cycles with >99% Li 2 S utilization. Furthermore, a Li-metal-free (anode-less) full cell retained over 80% of its initial capacity after 240 cycles. This work underscores the promise of leveraging Fe-stabilized polysulfides in enabling high-energy, long-lasting, solid-state Li-S batteries.

25 ENERGY STORAGE↗
DOE OSTI2026

Enhanced cycling stability of Ni-rich Li-metal cells enabled by dual vinylene carbonate and tris(trimethylsilyl)borate electrolyte additives

NMC811 (LiNi 0.8 Co 0.1 Mn 0.1 O 2 ) and other high-Ni chemistries are promising cathode candidates for high-performance electric vehicles, owing to their high energy density and reduced cobalt content. However, their long-term cycling stability is hindered by surface degradation, particularly when paired with conventional electrolytes and a lithium metal anode. Electrolyte additives represent a practical approach to enhance interfacial stability and improve overall battery performance by promoting the formation of a robust electrolyte–electrode interphase (EEI). In this study, we revisit the effects of vinylene carbonate (VC) and tris(trimethylsilyl)borate (TMSB) additives on single-crystal SC-NMC811||Li cells. While TMSB only increases the open-circuit voltage and initial overpotential, it delivers superior capacity retention at C/3 compared to cells containing only VC or a dual additive system (VC and TMSB). Notably, under fast-charging conditions (1C, 2C, and 5C), the dual-additive system significantly outperforms other formulations, achieving markedly enhanced long-term capacity retention. Comprehensive electrochemical and spectroscopic analyses reveal that the VC/TMSB dual-additive system suppresses surface transition in NMC811, mitigates structural degradation by forming a thin, LiF-deficient cathode-electrolyte interface (CEI) layer. Moreover, they promote smooth and dense Li deposition and generate a LiF-deficient solid-electrolyte interphase (SEI). Consequently, the synergistic stabilization of both the CEI and SEI effectively limits the overall cell impedance growth during extended cycling. These findings provide key insights into co-additive strategies for engineering stable interfaces in high-energy Ni-rich Li-metal batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Chemomechanical origin of morphological disparity in lithium metal electrodeposition

The morphology of electrochemically deposited lithium (Li) critically governs the cycling stability and safety of Li metal batteries, yet the underlying controlling factors remain poorly understood. Even within the same coin cell, Li deposits can exhibit strikingly different morphologies, for example, sparse whiskers coexisting with particle-like deposits, indicting strong local variations in growth conditions. By combining cryogenic transmission electron microscopy with phase-field modeling, we here identify the root cause of this disparity. We reveal that the morphological divergence originates from the variations in structure and chemical composition of the initial SEI layer formed on the copper (Cu) substrate. These variations arise from substrate defects that induce localized electrochemical fields, driving selective dissociation of either solvent or salt, producing SEI layers with distinct chemomechanical properties. Solvent-derived organic SEI favors whisker growth, whereas salt-derived SEI promotes particle formation. This study establishes a direct mechanistic link between SEI chemomechanical properties and Li morphology, providing design principles for tailoring SEI layers to control Li deposition

energy storage↗
DOE OSTI2022

A Superior Carbonate Electrolyte for Stable Cycling Li Metal Batteries Using High Ni Cathode

Li metal batteries pairing Li metal anode with high-nickel layer structured oxide cathode are a promising energy storage technology to achieve high energy density. To obtain long cycling life for Li metal batteries, the electrolyte plays a pivotal role in stabilizing both the Li metal anode and the high-nickel cathode upon electrochemical cycling. Herein, we report a carbonate electrolyte that enables a Li||LiNi 0.8 Mn 0.1 Co 0.1 O 2 pouch cell to achieve a high gravimetric energy density of 366 Wh/kg and unprecedented cycling stability with 80% capacity retention after 335 cycles. Here, the 19 F quantitative nuclear magnetic resonance spectroscopy and interface characterization demonstrate that FEC and LiDFOB can reduce the consumption rate of each other and the electrolyte, form a robust LiF-rich SEI on Li metal anode, and improve the microstructure integrity of the high-nickel cathode.

25 ENERGY STORAGE↗
DOE OSTI2024

Improved Stability of Oxysulfide Solid-State Electrolytes in Li(G3)TFSI Solvate Ionic Liquid Electrolyte

The performance of all solid-state batteries is limited by poor interfacial contact between active material and solid-state electrolyte (SSE) particles. Semi-solid batteries utilize a secondary electrolyte phase to wet the SSE/AM interface to improve cell performance. Solvate ionic liquids (SILs) are one class of liquid electrolytes under consideration for use in semi-solid batteries. This paper focuses on the Li(G3)TFSI SIL consisting of the bis(trifluoromethanesulfonyl)imide (TFSI − ) anion coupled to a [Li(G3)] + solvate cation. Sulfide SSEs are normally subject to nucleophilic attack by trigylme (G3), however, strong coordination of Li + to G3 in the [Li(G3)] + solvate cation prevents this reaction from taking place. Consequently, the stability of sulfide SSE depends on the ideal 1:1 molar ratio of G3 to TFSI, which may be difficult to maintain. We studied the chemical stability of 70Li 2 S·(30-x)P 2 S 5 ·xP 2 O 5 (x = 0, 2, 5, 10) (oxy)sulfide solid-state electrolyte in Li(G3)TFSI SIL. By physical measurement, UV–vis spectroscopy, electrochemical evaluation, X-ray photoelectron spectroscopy, and first principles calculation it is shown that increased oxygen content improves the stability of SSE in various Li(G3) x TFSI (x = 1, 2, 3, 4) liquid electrolytes. The results suggest that an oxysulfide SSE + SIL semi-solid electrolyte is a good choice for future semi-solid battery designs.

Electrochemistry↗
DOE OSTI2020

Lithium-Sulfur Batteries with a Block Copolymer Electrolyte Analyzed by X-ray Microtomography

Most of the work on Lithium-sulfur (LiS) batteries use liquid electrolytes that have limited stability when coupled with Li metal anodes. We have studied LiS batteries with a solid block copolymer electrolyte which exhibits improved stability against Li anodes. Additionally, the electrolyte comprises a polystyrene-b-poly(ethylene oxide) (SEO) copolymer doped with a Li salt. Hollow carbon nanospheres impregnated with sulfur were used to build a composite cathode. Two types of sulfur-impregnated functionalized carbon nanospheres were used: One with carboxylic acid groups and the other with short lithium poly(4-styrenesulfonyl(trifluoromethylsulfonyl)imide) (PSTFSI-Li) chains. Cells with Li S dissolved in the SEO based electrolyte served as the baseline. After cycling, the reason for capacity fade was determined by imaging the batteries using synchrotron hard X-ray microtomography. It is generally assumed that LiS cells fail due to dissolution of polysulfide into the liquid electrolyte, i.e., the main problems related to the cathode. In our all-solid cells, failure was primarily due to delamination of the Li foil from the polymer electrolyte layer. Delamination is also observed at the sulfur cathode. It is likely that the large changes in volume of the active materials during cycling induce delamination in all-solid LiS cells. 2 8

25 ENERGY STORAGE↗
DOE OSTI2020

Enhanced Interfacial Stability of Si Anodes for Li-Ion Batteries via Surface SiO2 Coating

Silicon is a promising alloying anode for lithium-ion batteries owing to its high capacity and low cost. However, its use has been hampered by mechanical failure arising from the large volume change upon cycling and by an insufficiently stable solid-electrolyte interphase (SEI). SEI formation depends on the Si surface, which is often an oxide (SiO x ). In this study we compare three different Si surfaces using Si wafers: 1.3 nm native SiO x , 1.4 nm thermally grown SiO2, and a SiOx-free surface. The oxide-free surface showed the worst electrochemical performance, never exceeding 94% Coulombic efficiency (CE). Furthermore, it also exhibited the thickest SEI and the highest overpotential for lithiation, which correlated with uninhibited electrolyte reduction and the incorporation of P-F species into the SEI. The oxide-coated surfaces performed significantly better, demonstrating a CE above 99% beyond the second cycle, low overpotential for lithiation, and a thinner and more stable SEI. The oxides lower the onset potential for electrolyte reduction, and yield an SEI with fewer P-F species. However, it was found that the CE with the native oxide surface decays from the fifth cycle onwards and correlates with a resurgence of electrolyte reduction. A 1-2 nm thermal SiO 2 coating is optimum for achieving a stable SEI that minimizes side reactions and sustains efficient cycling.

25 ENERGY STORAGE↗
DOE OSTI2024

Electron Glass Phase with Resilient Zhang-Rice Singlets in LiCu 3 ⁢O 3

LiCu 3 ⁢O 3 is an antiferromagnetic mixed valence cuprate where trilayers of edge-sharing Cu(II)O (3⁢d 9 ) are sandwiched in between planes of Cu(I) (3⁢d 10 ) ions, with Li stochastically substituting Cu(II). Angle-resolved photoemission spectroscopy (ARPES) and density functional theory reveal two insulating electronic subsystems that are segregated in spite of sharing common oxygen atoms: a Cu d z 2 /O p z derived valence band (VB) dispersing on the Cu(I) plane, and a Cu 3⁢d x 2 -y 2 /O 2⁢p x,y derived Zhang-Rice singlet (ZRS) band dispersing on the Cu(II)O planes. First-principle analysis shows the Li substitution to stabilize the insulating ground state, but only if antiferromagnetic correlations are present. Li further induces substitutional disorder and a 2D electron glass behavior in charge transport, reflected in a large 530 meV Coulomb gap and a linear suppression of VB spectral weight at E F that is observed by ARPES. Surprisingly, the disorder leaves the Cu(II)-derived ZRS largely unaffected. Finally, this indicates a local segregation of Li and Cu atoms onto the two separate corner-sharing Cu⁡(II)⁢O 2 sub-lattices of the edge-sharing Cu(II)O planes, and highlights the ubiquitous resilience of the entangled two hole ZRS entity against impurity scattering.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS1991

The effect of zinc additions on the environmental stability of Alloy 8090 (Al-Li-Cu-Mg-Zr)

Stress corrosion cracking (SCC) remains a problem in both Al-Li and conventional Al heat treatable alloys. It has recently been found that relatively small additions (less than or approximately 1 wt-percent) of Zn can dramatically improve the SCC performance of alloy 8090 (Al-Li-Cu-Mg-Zr). Constant load time to failure experiments using cylindrical tensile samples loaded between 30 and 85 percent of TYS indicate improvements of orders of magnitude over the baseline 8090 for the Zn-containing alloys under certain aging conditions. However, the toughnesses of the alloys were noticeably degraded due to the formation of second phase particles which primarily reside on grain and subgrain boundaries. EDS revealed that these intermetallic particles were Cu and Zn rich. The particles were present in the T3 condition and were not found to be the result of quench rate, though their size and distribution were. At 5 hours at 160 C, the alloys displayed the greatest susceptibility to SCC but by 20 hours at 160 C the alloys demonstrated markedly improved TTF lifetimes. Aging past this time did not provide separable TTF results, however, the alloy toughnesses continued to worsen. Initial examination of the alloys microstructures at 5 and 20 hours indicated some changes most notably the S' and delta' distributions. A possible model by which this may occur will be explored. Polarization experiments indicated a change in the trend of E(sub BR) and passive current density at peak aging as compared to the baseline 8090. Initial pitting experiments indicated that the primary pitting mechanism in chloride environments is one occurring at constituent (Al-Fe-Cu) particles and that the Cu and Zn rich boundary precipitates posses a breakaway potential similar to that of the matrix acting neither anodic or cathodic in the first set of aerated 3.5 w/o NaCl experiments. Future work will focus on the identification of the second phase particles, evaluation of K(sub 1SCC) and plateau da/dt via both DCB and slow strain rate techniques. A lower Zn content variant will be examined in the near future in hopes of optimizing toughness, density and SCC performance.

Kilmer, Raymond J.↗
DOE OSTI2021

A Bi-Layer Dense/Porous Solid Electrolyte Interphase for Enhanced Lithium-Metal Stability

Due to its high theoretical capacity and low electrochemical potential, lithium metal is a highly investigated anode for next-generation high-energy batteries. However, the unstable chemical and topographical heterogeneous surface of lithium gives rise to safety and efficiency concerns that prevent it from being utilized in practical applications. Exposure to electrolyte leads to non-uniform, mixed organic-inorganic solid-electrolyte interphase (SEI) formation, starting a cascading to non-uniform flux distribution, consumption of active materials, and dendrite growth. The SEI is the key feature that will lead to harnessing the capabilities possible with lithium metal. In this work, the formation of a closed-host bi-layer solid electrolyte interphase (SEI) improves the stability of lithium anode. This is successfully realized by forming an interconnected porous LiF-rich artificial SEI in contact with Li metal, and a dense, stable in-situ formed upper layer SEI. The porous layer increases the number of Li/LiF interfaces, which reduces local volume fluctuations and improves Li+ diffusion along these interfaces. Additionally, the tortuous porous structure guides uniform Li+ flux distribution and mechanically suppresses dendrite propagation. The dense upper layer of the SEI accomplishes a closed-host design through reaction with LiNO3 additive and prevents continuous consumption of active materials seen without the additive included in the electrolyte. The duality of a dense top layer with porous bottom layer led to extended cycle life and improved rate performance, evidenced with symmetric cell testing, as well as full cell testing paired with sulfur and LiFePO4 (LFP) cathodes. This work is a good example of a rational design of the SEI, based on comprehensive consideration of various critical factors to improve Li-metal anode stability, and highlights a new pathway to improve cycling and rate performances of Li metal batteries.

25 ENERGY STORAGE↗
DOE OSTI2022

Highly reversible Li 2 RuO 3 cathodes in sulfide-based all solid-state lithium batteries

The practical application of high-capacity lithium-rich cathode materials in lithium-ion batteries has been largely restricted by severe side reactions with electrolytes. Herein, we report a highly stable lithium-rich Li 2 RuO 3 cathode by forming a passivating solid electrolyte interphase at the interface with a sulfide solid electrolyte such as Li 6 PS 5 Cl in all-solid-state lithium batteries (ASSLBs), which efficiently suppresses serious parasitic interfacial reactions and fast-increasing interfacial impedance normally observed in liquid electrolytes. The exceptionally high interfacial stability of the Li 2 RuO 3 /sulfide electrolyte interface contributes to a high reversible capacity of 257 mA h g –1 of Li 2 RuO 3 at 0.05C rate, and unprecedented cycling stability with 90% capacity retention after 1000 cycles at 1C rate. Iin this work, comprehensive experimental characterizations and first-principles calculations disclose that electronically insulating interfacial reaction products forming at the interface between the Li 2 RuO 3 cathode and Li 6 PS 5 Cl facilitate the formation of a stable and passivating interphase and block the continuous side reactions. Importantly, reversible oxygen redox activity of Li 2 RuO 3 is well-maintained in this configuration of ASSLBs even after 600 cycles, thus the common voltage decay of the Li-rich material is also significantly reduced. These new discoveries demonstrate the critical role of interface design for achieving prolonged cycling stability of lithium-rich cathode materials.

25 ENERGY STORAGE↗
DOE OSTI2024

A Fluorinated Lewis Acidic Organoboron Tunes Polysulfide Complex Structure for High–Performance Lithium–Sulfur Batteries

Many challenges in lithium-sulfur (Li–S) batteries are associated with the radical change in lithium polysulfide (LPS) solubility during cycling, but chemical approaches to address such inconsistency are still lacking. Here, the use of a strong Lewis acidic fluorinated organoboron, tri(2,2,2-trifluoroethyl) borate (TFEB), is reported as a multi-functional mediator to simultaneously overcome multiple technical barriers in practical Li–S batteries. TFEB acts as an anion acceptor and forms strong molecular complexes with Lewis basic LPS. The TFEB-LPS complexes have consistent solubility across the full polysulfide spectrum and deliver several times improved better redox kinetics, unlocking a true redox catalytic mechanism that covers the majority of redox events in thick sulfur cathodes. As a result, Li–S batteries evaluated under practical conditions exhibit significantly improved discharge capacity, rate capability, and cycling stability with the addition of the TFEB additive. More importantly, TFEB also contributes to the stabilization of lithium anode in the presence of polysulfides by generating strong interfacial film. These attributes significantly improve the cycling stability of practical Li–S pouch cells, which are assembled with a unit energy density of 219 Wh kg –1 . Finally, the results provide new molecular insights on the design of unlocking solvation networks of practical Li–S systems.

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2021

A Polymer-in-Salt Electrolyte with Enhanced Oxidative Stability for Lithium Metal Polymer Batteries

Lithium (Li) metal polymer batteries (LMPBs) are a promising candidate of solid-state batteries with high safety. However, rare progress has been demonstrated so far in high voltage stability of polyethylene oxide (PEO) based polymer electrolytes for LMPBs. Herein, we revived the polymer-in-salt electrolyte (PISE) strategy based on the PEO-LiFSI system with EO/Li = 8 through a dry process to avoid the contamination of the residual solvent. The obtained PISEs exhibit quite different morphologies and coordination structures which greatly enhance the oxidative stability of polymer electrolytes. P(EO)1LiFSI has a low melting temperature, a high ionic conductivity at 60 ?C and an oxidative stability of ~4.5 V vs. Li/Li+ (overcoming the inherent low oxidative stability of PEO). With an effective interphase rich in inorganic species, in combination with good stability of the hybrid polymer electrolyte towards Li metal, the cycling stability of Li||LiNi1/3Co1/3Mn1/3O2 is greatly improved. The LMPB can retain 74.4% of capacity after 186 cycles at 60 ?C under the charge cutoff voltage of 4.3 V. The findings point out a promising strategy to develop high-voltage stable polymer electrolytes for high energy-density and safe LMPBs.

Polymer-in-salt electrolyte, lithium metal battery↗
DOE OSTI2021

Importance of Superstructure in Stabilizing Oxygen Redox in P3‐Na 0.67 Li 0.2 Mn 0.8 O 2

Abstract Activation of oxygen redox represents a promising strategy to enhance the energy density of positive electrode materials in both lithium and sodium‐ion batteries. However, the large voltage hysteresis associated with oxidation of oxygen anions during the first charge represents a significant challenge. Here, P3‐type Na 0.67 Li 0.2 Mn 0.8 O 2 is reinvestigated and a ribbon superlattice is identified for the first time in P3‐type materials. The ribbon superstructure is maintained over cycling with very minor unit cell volume changes in the bulk while Li ions migrate reversibly between the transition metal and Na layers at the atomic scale. In addition, a range of spectroscopic techniques reveal that a strongly hybridized Mn 3d–O 2p favors ligand‐to‐metal charge transfer, also described as a reductive coupling mechanism, to stabilize reversible oxygen redox. By preparing materials under three different synthetic conditions, the degree of ordering between Li and Mn is varied. The sample with the maximum cation ordering delivers the largest capacity regardless of the voltage windows applied. These findings highlight the importance of cationic ordering in the transition metal layers, which can be tuned by synthetic control to enhance anionic redox and hence energy density in rechargeable batteries.

36 MATERIALS SCIENCE↗
DOE OSTI2021

First principles study of the stability and thermal conductivity of novel Li-Be hybrid ceramics

Hybrid Li-Be ceramics, combining both tritium (T) breeder (Li) and neutron multiplier (Be) for use as part of the fuel cycle of future nuclear fusion reactors are proposed. The development of such hybrid materials may reduce thermal gradients through better matching of thermal properties, mitigating the detrimental effects that may accompany traditional breeder systems while maintaining acceptable neutron multiplication and T breeding. Here, first-principles methods are used to investigate stability and thermal transport properties of a set of compounds containing both Li and Be. It is demonstrated that BeLi 2 O 4 Ge and BeLi 2 O 4 Si are mechanically stable and have formation energies comparable with leading candidates for solid state breeder materials, Li 2 TiO 3 , Li 2 ZrO 3 . It is also demonstrated that similar to the leading candidates, these compounds are insulators with thermal transport defined by phonons. The calculated thermal conductivity of BeLi 2 O 4 Ge is slightly higher compared to Li 2 TiO 3 or Li 2 ZrO 3 while in the BeLi 2 O 4 Si it is almost three times higher compared to the rest of compounds due to a higher phonon group velocities and increased phonon lifetimes. These results indicate that hybrid Li-Be ceramics offer a potential route towards better matching of thermal properties with minimal functional property degradation, thereby offering better overall fuel cycle performance.

36 MATERIALS SCIENCE↗