Search NASA⌕ Search

SEARCH · Search NASA

Results for “Material Response”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

A diffusion–deformation model with damage for polymer undergoing rapid decompression failure

Green hydrogen is emerging as one of the most promising alternatives to replace fossil fuels. While hydrogen gas has a good energy density by weight, its poor energy density by volume requires it to be stored under high pressure for commercial use. The hydrogen infrastructure developed to handle this high pressure hydrogen contains multiple components made of polymers as sealing agents. Although polymers do not react chemically with hydrogen gas, they undergo a mechanical failure when high pressure hydrogen gas is suddenly depressurized. This phenomenon known as 'rapid decompression failure' occurs due to the diffusion of hydrogen through polymer and getting trapped inside pre-existing cavities or voids. Here, in this paper, a continuum mechanics-based coupled diffusion-deformation-damage model was developed to predict the hydrogen distribution, stress distribution, and damage propagation inside the polymer while it undergoes rapid decompression failure. The polymer was modeled as a hyperelastic material because it represents the nonlinear material response observed in uniaxial tensile tests perfectly. The effects of hydrogen diffusivity, pre-existing cavity size, cavity location, applied hydrogen pressure, and depressurization rate on damage initiation were studied. It was found that the coefficient of diffusion plays an important role in damage initiation and damage was mostly concentrated in the inside areas rather than near the surface. Experiments were conducted with EPDM polymer which agreed well with the predicted trends using the given model. The effect of adding carbon black and silica filler particles and plasticizer to the pure EPDM polymer was also studied. It was found that damage during RDF decreases with the addition of fillers, but increases with the addition of the plasticizer. Finally, the damage evolution in the presence of two cavities was also studied, and was found that the interaction of stress fields around the cavities alters the damage occurring during RDF.

36 MATERIALS SCIENCE↗
DOE OSTI2022

The Potential Energy Hotspot: Effects of Impact Velocity, Defect Geometry, and Crystallographic Orientation

In energetic materials, the localization of energy into “hotspots” is known to dictate the initiation of chemical reactions and detonation. Recent all-atom simulations have shown that more energy is localized as internal potential energy (PE) than can be inferred from the kinetic energy (KE) alone. The mechanisms associated with pore collapse and hotspot formation are known to depend on pore geometry and dynamic material response such as plasticity. Therefore, we use molecular dynamics (MD) simulations to characterize shock-induced pore collapse and the subsequent formation of hotspots in 1,3,5-triamino-2,4,6-trinitrobenzene (TATB), a highly anisotropic molecular crystal, for various defect shapes, shock strengths, and crystallographic orientations. We find that the localization of energy as PE is consistently larger than the KE in cases with significant plastic deformation. Additionally, an analysis of MD trajectories reveals the underlying molecular- and crystal-level processes that govern the effect of orientation and pore shape on PE localization. We find that the regions of highest PE relate to the areas of maximum plastic deformation, while KE is maximized at the point of impact. Comparisons against octahydro-1,3,5,7-tetranitro-1,3,5,7-tetrazocine (HMX) reveal less energy localization in TATB, which could be a contributing factor to the latter’s insensitivity.

36 MATERIALS SCIENCE↗
DOE OSTI2024

A prediction model of failure threshold for shear deformation in a Zr-based bulk metallic glass

The failure of bulk metallic glasses (BMGs) during plastic deformation at room temperature is abrupt and instantaneous, while the analysis of precursor information based on avalanche events helps predict catastrophic failure. An acoustic emission (AE) signal can provide accurate precursor information for material failure, due to its sensitive and high fast calculation ability. In the current study, AE monitoring tests are carried out during uniaxial compression tests of BMGs at different strain rates. The AE experimental failure threshold, E max , is proposed on the basis of AE cumulative energy, which reflects the intensity of damage evolution at different loading conditions. Compared with the critical shear band velocity (CSBV) associated with stick-slip dynamics of serrated flow, E max is a more sensitive failure parameter since it is connected with the local microscopic changes that occur during the material response process. Here, the E max is obtained prior to reaching the CSBV since the calculation of these two avalanches analysis focuses on the different stages of shear band growth. In particular, AE events are related to the “dry” friction process in the first stage, however, the CSBV is responsible for the “viscous” glide in the second stage. Therefore, Emax is not affected by the complex interactions between the shear bands during the stick-slip process. The maximum avalanche of serrated flow, S max , is proposed as the experimental failure threshold, which depends on the applied strain rate as S max ~ $\dot{ε}$ –λ . According to the relationship of E max and S max , the theoretical failure threshold, E max , follows a criterion E max = 2545$\dot{ε}$ –λ - 4468, where λ is equivalent to 0.15 for this work. Finally, combining the different calculations and AE measurements, this model gives new insights to predict the deformation failure behavior of Zr-based BMGs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Air oxidation of yttrium hydride as a high temperature moderator for thermal neutron spectrum fission reactors

Yttrium hydride (YH x ) is an attractive moderator material for thermal neutron spectrum fission reactors requiring a small reactor core volume and has been selected as the neutron moderator for the Transformational Challenge Reactor (TCR), an advanced gas-cooled microreactor. Before YH x can be used in this application, it is important to understand the material response to off-normal conditions. In the present study, 550–650 °C isothermal dry air oxidation was performed to simulate a depressurized loss of force circulation (DLOFC) event. The oxidation was performed using thermogravimetric analysis (TGA) on bulk crack-free YHx coupons. Oxidation studies were also performed on Y coupons to elucidate the impact of H on oxidation. Both the chemistry and distribution of processing impurities were found to strongly affect oxidization behavior on a batch-to-batch basis. Regardless of batch, YHx oxidized at a significantly lower rate than Y at all temperatures, and the lower rate was directly correlated with increased hydride content. Metallic Y exhibited complex exponential kinetics, whereas YH x also exhibited complex kinetics but gained considerably less mass. According to literature reports on protonic and native-ion conductivities of Y 2 O 3 and mass spectrometry analysis of gaseous reaction products formed during the oxidation of YH x , a mechanism for the reduced oxidation rate of yttrium hydride is suggested.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Bio-inspired non self-similar hierarchical elastic metamaterials

Hierarchy provides unique opportunities for the design of advanced materials with superior properties that arise from architecture, rather than from constitutive material response. Contrary to the quasi-static regime, where the potential of hierarchy has been largely explored, its role in vibration mitigation and wave manipulation remains elusive. So far, the majority of the studies concerning hierarchical elastic metamaterials have proposed a self-similar repetition of a specific unit cell at multiple scale levels, leading to the activation of the same bandgap mechanism at different frequencies. On the contrary, here, we show that by designing non self-similar hierarchical geometries allows us to create periodic structures supporting multiple, highly attenuative and broadband bandgaps involving (independently or simultaneously) different scattering mechanisms, namely, Bragg scattering, local resonance and/or inertial amplification, at different frequencies. The type of band gap mechanism is identified and discussed by examining the vibrational mode shapes and the imaginary component of the wavenumber in the dispersion diagram of the unit cell. Finally, we also experimentally confirm this by performing measurements in the lowest frequency regime on a 3D printed structure. Hierarchical design strategies may find application in vibration mitigation for civil, aerospace and mechanical engineering.

36 MATERIALS SCIENCE↗
DOE OSTI2025

Optimizing ablator thickness for laser shock experiments

In laser shock experiments, a well-defined, flat-top shock wave at the ablator/sample interface is important for accurately probing material response under uniaxial strain compression. However, the relationship between the ablator thickness and the resulting shock wave characteristics is insufficiently understood, limiting the ability to design optimal experiments. To address this need, we conducted a systematic experimental study using a 100 J laser to shock-compress polyimide ablators to peak stresses ranging from 20.4 to 111.6 GPa. Laser interferometry diagnostics measured the transmitted wave profiles at the ablator/sample interface, consistently showing a single jump followed by a constant peak state before the arrival of release waves. Here, by analyzing shock transit time, flat-top duration, and stress, our results establish a framework for selecting ablator thickness to maximize the flat-top duration, improving the precision and reproducibility of laser shock experiments.

design of experiments↗
DOE OSTI2026

Time at Temperature Experiments on Neutron Irradiated Zircaloy-2 using Conventional & Flash DSC

Dryout events in Boiling Water Reactors (BWRs) are currently treated by NRC regulations as automatic disqualification for continued fuel rod operation, even though this criterion does not account for the rate or duration of power increases, associated changes in material behavior, or the possibility of rewetting. Operational history from Anticipated Operational Occurrences (AOOs) shows that short, transient power excursions often demand only modest heat removal, and industry experience suggests that fuel can briefly enter dryout yet return to safe, stable operation. The lack of detailed understanding of the material response during such events motivates the present series of experiments. This study uses unique and innovative methods to investigate microstructural evolution in irradiated Zircaloy-2 exposed to high temperatures in inert environments. Differential Scanning Calorimetry (DSC) and FlashDSC are combined to build a comprehensive experimental framework capable of identifying the a–ß phase transformation in zirconium and examining defect annealing under steep thermal gradients. FlashDSC enables rapid heating and cooling of Focused Ion Beam (FIB)–prepared large-area lift-outs (LALOs) of irradiated Zircaloy-2 at rates of 1,000 K/s to peak temperatures of 600°C, 750°C, and 900°C. The goal is to determine whether these conditions produce measurable microstructural changes that could influence cladding performance in typical BWR environments. Microstructural characterization includes quantifying dislocation density and assessing secondary phase particle (SPP) size and distribution using Transmission Electron Microscopy (TEM). Ongoing analysis, such as diffraction pattern indexing and 4D STEM processing, will further refine these observations.

36 - MATERIALS SCIENCE↗
DOE OSTI2025

Three-Dimensional Heat Flux and Thermal Analysis of Angled Tungsten Samples on DIII-D

ITER-grade tungsten and dispersoid-strengthened tungsten samples with the top surface angled at ~15° towards the incident plasma flux were exposed to 9 H-mode discharges with edge-localized modes (ELMs) in the lower divertor of DIII-D tokamak using the Divertor Material Evaluation System (DiMES). Surface damage included cracking and flaking of material on the two samples farthest away from the plasma strike point, and significant melting of the two samples closest to the strike point. Heat flux and thermal analysis tools new to DIII-D have been applied to better understand this material response and to help optimize the exposure conditions for future experiments. SMITER field-line tracing simulations based on IRTV data and EFIT equilibria estimate an average inter-ELM perpendicular heat flux, 𝑞⊥,𝑖nter−𝐸LM , on the angled surfaces of 10.1 – 19.6 MW/m² for a majority of the 9 discharges, increasing to 15.6 – 24.5 MW/m² for the single, higher-power shot where samples melted. Fast camera data showed shallow intra-ELM melting and re-solidification, which transitioned to bulk inter-ELM melting with melt motion in the 𝐽⃗ 𝑥 𝐵⃗ direction. About 50% of the protruding volume of the most affected sample was displaced via melt-motion. SIERRA thermal modeling software was able to reproduce an onset time of melting consistent with fast camera data and final sample conditions, within < 200 ms. Maximum surface temperatures of 3122 K and 2787 K are estimated for the samples farthest away from the strike point, while the closest samples achieve melting at 4067 ms and 4750 ms into the ~5000 ms plasma exposure. A +10% increase in both the SMITER 𝑞⊥,𝑖nter−𝐸LM calculations and the estimated ELM heat loads 𝑞⊥, 𝐸LM was required to achieve this result, which is within the uncertainty of the diagnostic data but likely accounts for non-ideal geometry effects plus other physics uncertainties not included in this first iteration of modeling. This work provided valuable estimates of the 3D temperature evolution to help better understand the observed surface morphology and internal recrystallization of samples, which are discussed in detail in a complementary manuscript [1]. Benchmarking efforts with more diagnosed DIII-D experiments are underway to further refine the SMITER and SIERRA models for DiMES. Future use of these tools will enable researchers to precisely target heat flux exposure conditions in DIII-D to test, but not exceed, the thermomechanical limitations of novel plasma-facing materials.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2021

Initial Developments in Modeling Graphite Behavior

Graphite is used in High Temperature Reactor designs as a moderator, reflector and core material responsible for protecting the fuel and maintaining structural stability. From a safety perspective, it is imperative to be able to predict how graphite will behave under reactor operating conditions which may compromise the core’s structural integrity or fuel’s safety performance. The following report summarizes recent modeling work undertaken at Idaho National Laboratory which focuses on graphite degradation behavior. One phenomenon which is explored in this report and can cause significant degradation to graphite properties is oxidation. Oxidation behavior in graphite is highly temperature dependent. At low temperatures, oxygen can fully penetrate a component and cause a homogeneous damage profile. At high temperatures, only the graphite near the surface of a component is affected. Understanding and modeling this temperature dependence is essential to predicting graphite behavior. In this report, three graphite models are discussed. The first model is used to investigate strength loss after low temperature oxidation. It does this by generating an approximate graphite microstructure then determining the required load to cause crack propagation. It has been shown that the model reproduces the quasi brittle stress versus strain relationship observed in graphite. Strength loss results from the model are shown to match experimental values. The second model investigates strength loss under high temperature oxidation conditions. This model is more applicable to full scale graphite components where the oxidation damage is often inhomogeneous throughout a component. The third model computes stresses in graphite under reactor conditions. Specifically, the model incorporates the effect of creep, irradiation dose, thermal strains, and oxidation in order to predict internal stresses in a component. All of these models are implemented in the Multiphysics Object-Oriented Simulation Environment (MOOSE), an open source, parallel finite element framework.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2026

Optimization of Processing, Microstructure, and Hardness of an Al–Ce–Ni–Mn–Zr Alloy With Laser Additive Manufacturing

Here, this study examines the processing behavior, microstructure, surface roughness, and hardness properties of an aluminum alloy containing 8.2 Ce, 4.5 Ni, 0.5 Mn, and 0.7 Zr (wt%) fabricated using laser powder bed fusion. Sixty samples were produced across a range of laser powers, scan speeds, and hatch spacings to evaluate their effect on porosity, hardness, and microstructural features. Porosity was measured using X-ray computed tomography, while microstructure and surface roughness were characterized by scanning electron (SEM) and laser confocal microscopy. High dense and cracking-free Al–Ni–Ce alloy was successfully manufactured. Porosity showed a U-shaped dependence on energy input, increasing under both insufficient and excessive melting conditions. Hardness increased with cooling rate due to finer cellular structures and solute redistribution. A general statistical model was developed to capture the relationships between processing parameters and material response. Results identify a narrow processing window defined by laser powers between 350 and 370 W, scan speeds from 1400 to 1800 mm/s, and hatch distances between 0.14 and 0.18 mm. Within this window, porosity is minimized (below 0.01%) and hardness is maximized (up to 160 HV), demonstrating that careful control of these parameters enables dense, high strength aluminum components suitable for demanding structural applications.

Aluminum alloys↗
DOE OSTI2025

Direct Imaging of Hydrogen‐Driven Dislocation and Strain Field Evolution in a Stainless Steel Grain

Hydrogen embrittlement (HE) poses a significant challenge to the durability of materials used in hydrogen production and utilization. Disentangling the competing nanoscale mechanisms driving HE often relies on simulations and electron-transparent sample techniques, limiting experimental insights into hydrogen-induced dislocation behavior in bulk materials. This study employs in situ Bragg coherent X-ray diffraction imaging to track three-dimensional (3D) dislocation and strain field evolution during hydrogen charging in a bulk grain of austenitic 316 stainless steel. Tracking a single dislocation reveals hydrogen-enhanced mobility and relaxation, consistent with dislocation dynamics simulations. Subsequent observations reveal dislocation unpinning and climb processes, likely driven by osmotic forces. Additionally, nanoscale strain analysis around the dislocation core directly measures hydrogen-induced elastic shielding. These findings experimentally validate theoretical predictions and offer mechanistic insights into hydrogen-driven dislocation behavior. The quantified nanoscale phenomena serve as critical inputs for multiscale modeling frameworks to predict bulk material responses and accelerate the development of HE-resistant alloys.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2025

Shape‐Evolving Structured Liquids

Migration, division, and reconfiguration - functions essential to living systems - are driven by active processes. Developing synthetic mimics is an outstanding challenge. Lipid bilayers that bound natural systems are locally deformed by active species, e.g., microtubules, but the resulting non-equilibrium shapes relax when active species motion ceases, and the shape changes lack immediate control. A fully synthetic system is described, driven by active particles encapsulated by a reconfigurable nanoparticle-surfactant membrane that undergoes shape fluctuations reminiscent of living cells. These shape changes are preserved after particle activity stops. Surfactant concentration tunes the interfacial tension over three orders of magnitude, making on-demand shape evolution possible. Directional migration, division, and reconfiguration across multiple scales are possible, leading to a new class of biomimetic, reconfigurable, and responsive materials, paving the way for autonomous synthetic machines.

Kim, Paul Y↗
DOE OSTI2022

A neural network‐enhanced reproducing kernel particle method for modeling strain localization

Abstract Modeling the localized intensive deformation in a damaged solid requires highly refined discretization for accurate prediction, which significantly increases the computational cost. Although adaptive model refinement can be employed for enhanced effectiveness, it is cumbersome for the traditional mesh‐based methods to perform while modeling the evolving localizations. In this work, neural network‐enhanced reproducing kernel particle method (NN‐RKPM) is proposed, where the location, orientation, and shape of the solution transition near a localization is automatically captured by the NN approximation via a block‐level neural network (NN) optimization. The weights and biases in the blocked parameterization network control the location and orientation of the localization. The designed basic four‐kernel NN block is capable of capturing a triple junction or a quadruple junction topological pattern, while more complicated localization topological patters are captured by the superposition of multiple four‐kernel NN blocks. The standard RK approximation is then utilized to approximate the smooth part of the solution, which permits a much coarser discretization than the high‐resolution discretization needed to capture sharp solution transitions with the conventional methods. A regularization of the NN approximation is additionally introduced for discretization‐independent material responses. The effectiveness of the proposed NN‐RKPM is verified by a series of numerical verifications.

Baek, Jonghyuk↗
DOE OSTI2026

Geometrical effects on the measured neutron residual stress in additively manufactured cold spray AA6061

Aluminum cold spray additive builds were made with varying wall widths and geometries to explore the effects of build geometry on residual stress development in the additively sprayed material. Deposition rates of over 750 g/hr were achieved without any cracking or delamination of the additively manufactured components. Neutron residual stress measurements revealed a maximum tensile residual stress of 41 MPa at the interface of the substrate and a maximum compressive residual stress of −35 MPa in the cold sprayed material. While there was not found to be significant residual stress changes between the cold sprayed walls, the cold sprayed cylinder had varying residual stress throughout the diameter with the outer diameter having a higher tensile residual stress than the interior. The low residual stress and minimal geometrical dependency demonstrate further part size is possible without concerns for component failure in AA6061. The application of common coating residual stress models to full scale additive builds is evaluated and discussed. The lack of residual stress evolution was studied by in-situ coating property measurement that revealed that the deposition stress of the AA6061 sprays reduced with increased layer thickness. In conclusion, this study provides insight into the evolution of residual stress in cold spray additive components and how both the mechanics and material responses differ from coatings.

Additive manufacturing↗
DOE OSTI2024

Extreme sparsification of physics-augmented neural networks for interpretable model discovery in mechanics

Data-driven constitutive modeling with neural networks has received increased interest in recent years due to its ability to easily incorporate physical and mechanistic constraints and to overcome the challenging and time-consuming task of formulating phenomenological constitutive laws that can accurately capture the observed material response. However, even though neural network-based constitutive laws have been shown to generalize proficiently, the generated representations are not easily interpretable due to their high number of trainable parameters. Sparse regression approaches exist that allow for obtaining interpretable expressions, but the user is tasked with creating a library of model forms which by construction limits their expressiveness to the functional forms provided in the libraries. Here, in this work, we propose to train regularized physics-augmented neural network-based constitutive models utilizing a smoothed version of $L^0$-regularization. This aims to maintain the trustworthiness inherited by the physical constraints, but also enables interpretability which has not been possible thus far on any type of machine learning-based constitutive model where model forms were not assumed a priori but were actually discovered. During the training process, the network simultaneously fits the training data and penalizes the number of active parameters, while also ensuring constitutive constraints such as thermodynamic consistency. We show that the method can reliably obtain interpretable and trustworthy constitutive models for compressible and incompressible hyperelasticity, yield functions, and hardening models for elastoplasticity, using synthetic and experimental data. This work aims to set a new paradigm for interpretable machine learning models in the broad area of solid mechanics where low and limited data is available along with prior knowledge of physical constraints that the learned maps need to obey. This paradigm can potentially be extended to a broader spectrum of scientific exploration.

Data-driven constitutive models↗
DOE OSTI2025

Effect of pore fluid chemistry on the mechanical behavior of a divalent compacted bentonite, an experimental and constitutive study

Ongoing research in isolating high-level nuclear waste and spent fuel has highlighted compacted bentonite as a suitable material for engineered barrier systems in deep geological repositories due to its extraordinary swelling and retention properties. This research focuses on the chemo-mechanical behavior of compacted bentonite exposed to different pore fluids with different concentrations and loading conditions. The study involves swelling pressure and compressibility experiments along with mineralogy analysis employing X-ray diffraction (XRD) and Cation exchange. The tests were conducted on BCV (a Mg/Ca- bentonite) compacted at a dry density of 1.48 ± .02 Mg/m 3 . An advanced chemical-mechanical constitutive model for unsaturated highly expansive clays was adopted to simulate the material response and better understand its behavior. The model is able to account for the main phenomena at both macro and microstructural levels and the interactions between them. The model successfully replicated experimental observations. The XRD analyses support the macroscopic observation, indicating that salinity impacts crystalline swelling as demonstrated by the reduction of basal spacing from 19.27 Å to 15.68 Å when the osmotic suction increases from 0 MPa to 33 MPa. The results suggested that the osmotic pressure generated by the concentration in the pore fluids promotes a reduction in swelling pressures, swelling strains, and crystalline swelling of clay minerals. Also, it affects the pre-consolidation stress and the compressibility of the compacted samples. In conclusion, it was also observed that both solution type and solution concentration impact the clay swelling pressure.

Chemo-mechanical constitutive model↗
DOE OSTI2020

Localization of deformation in fluid-saturated sandstone

Herein we discuss a laboratory study of inelastic deformation and localization was conducted to evaluate microseismicity and fracture in fluid-saturated rock. Plane strain compression experiments were performed on oil- and water-saturated Berea sandstone under dry, drained, undrained, and quasi-unjacketed conditions. Parameters associated with the elastic and inelastic material response were accurately measured and used in a constitutive model to predict localization of deformation under the drained and undrained conditions. Acoustic emission (AE) activity was recorded and the onset of inelastic response in fluid-saturated rock, similar to dry rock, coincided with an increase in AE rate. Fracture initiation and propagation were successfully monitored by AE locations. Clustering of AE events and the start of inhomogeneous deformation inferred from displacement measurements are shown to be well correlated with the model prediction of the onset of localized deformation under various rock-fluid interaction conditions.

42 ENGINEERING↗
DOE OSTI2024

Subject-specific multi-scale modeling of the fate of inhaled aerosols

Determining the fate of inhaled aerosols in the respiratory system is essential in assessing the potential toxicity of inhaled airborne materials, responses to airborne pathogens, or in improving inhaled drug delivery. The availability of high-resolution clinical lung imaging and advances in the reconstruction of lung airways from CT images have led to the development of subject-specific in-silico 3D models of aerosol dosimetry, often referred to as computational fluid-particle-dynamics (CFPD) models. As CFPD models require extensive computing resources, they are typically confined to the upper and large airways. These models can be combined with lower-dimensional models to form multiscale models that predict the transport and deposition of inhaled aerosols in the entire respiratory tract. Understanding where aerosols deposit is only the first of potentially several key events necessary to predict an outcome, being a detrimental health effect or a therapeutic response. To that end, multiscale approaches that combine CFPD with physiologically-based pharmacokinetics (PBPK) models have been developed to evaluate the absorption, distribution, metabolism, and excretion (ADME) of toxic or medicinal chemicals in one or more compartments of the human body. CFPD models can also be combined with host cell dynamics (HCD) models to assess regional immune system responses. Here, this paper reviews the state of the art of these different multiscale approaches and discusses the potential role of personalized or subject-specific modeling in respiratory health.

60 APPLIED LIFE SCIENCES↗