Results for “Mesh validity” — Page 8

NASA NTRS1991

The aerodynamic characteristics of vortex ingestion for the F/A-18 inlet duct

A Reduced Navier-Stokes (RNS) solution technique was successfully combined with the concept of partitioned geometry and mesh generation to form a very efficient 3-D RNS code aimed at the analysis-design engineering environment. Partitioned geometry and mesh generation is a pre-processor to augment existing geometry and grid generation programs which allows the solver to (1) recluster an existing gridlife mesh lattice, and (2) perturb an existing gridfile definition to alter the cross-sectional shape and inlet duct centerline distribution without returning to the external geometry and grid generator. The present results provide a quantitative validation of the initial value space marching 3-D RNS procedure and demonstrates accurate predictions of the engine face flow field, with a separation present in the inlet duct as well as when vortex generators are installed to suppress flow separation. The present results also demonstrate the ability of the 3-D RNS procedure to analyze the flow physics associated with vortex ingestion in general geometry ducts such as the F/A-18 inlet. At the conditions investigated, these interactions are basically inviscid like, i.e., the dominant aerodynamic characteristics have their origin in inviscid flow theory.

Anderson, Bernhard H.↗

NASA NTRS1995

Thermal behavior spiral bevel gears

An experimental and analytical study of the thermal behavior of spiral bevel gears is presented. Experimental data were taken using thermocoupled test hardware and an infrared microscope. Many operational parameters were varied to investigate their effects on the thermal behavior. The data taken were also used to validate the boundary conditions applied to the analytical model. A finite element-based solution sequence was developed. The three-dimensional model was developed based on the manufacturing process for these gears. Contact between the meshing gears was found using tooth contact analysis to describe the location, curvatures, orientations, and surface velocities. This information was then used in a three-dimensional Hertzian contact analysis to predict contact ellipse size and maximum pressure. From these results, an estimate of the heat flux magnitude and the location on the finite element model was made. The finite element model used time-averaged boundary conditions to permit the solution to attain steady state in a computationally efficient manner.Then time- and position-varying boundary conditions were applied to the model to analyze the cyclic heating and cooling due to the gears meshing and transferring heat to the surroundings, respectively. The model was run in this mode until the temperature behavior stabilized. The transient flash temperature on the surface was therefore described. The analysis can be used to predict the overall expected thermal behavior of spiral bevel gears. The experimental and analytical results were compared for this study and also with a limited number of other studies. The experimental and analytical results attained in the current study were basically within 10% of each other for the cases compared. The experimental comparison was for bulk thermocouple locations and data taken with an infrared microscope. The results of a limited number of other studies were compared with those obtained herein and predicted the same basic behavior.

Handschuh, Robert F.↗

NASA NTRS1998

3D Navier-Stokes Time Accurate Solutions Using Multipartitioning Parallel Computation Methodology

A parallel CFD code solving 3D time accurate Navier-Stokes equations with multipartitioning parallel Methodology is being developed in collaboration with Ohio State University within the Air Vehicle Directorate, at Wright Patterson Air Force Base. The advantage of the multipartitioning parallel method is that the domain decomposition will not introduce domain boundaries for the implicit operators. A ring structure data communication is employed so that the implicit time accurate method can be implemented for multi-processors with the same accuracy as for the single processor. No sub-iteration is needed at the domain boundaries. The code has been validated for some typical unsteady flows, which include Coutte Flow, flow passing a cylinder. The code now is being employed for a large scale time accurate wall jet transient flow computation. 'ne preliminary results are promising. The mesh has been refined to capture more details of the flow field. The mesh refinement computation is in progress and would be difficult to successfully implement without the parallel computation techniques used. A modified version of the code with more efficient inversion of the diagonalized block matrix is currently being tested.

Zha, Ge-Cheng↗

NASA NTRS2010

Analysis of the Effects of Streamwise Lift Distribution on Sonic Boom Signature

The streamwise lift distribution of a wing-canard-stabilator-body configuration was varied to study its effect on the near-field sonic boom signature. The investigation was carried out via solving the three-dimensional Euler equation with the OVERFLOW-2 flow solver. The computational meshes were created using the Chimera overset grid topology. The lift distribution was varied by first deflecting the canard then trimming the aircraft with the wing and the stabilator while maintaining constant lift coefficient of 0.05. A validation study using experimental results was also performed to determine required grid resolution and appropriate numerical scheme. A wide range of streamwise lift distribution was simulated. The result shows that the longitudinal wave propagation speed can be controlled through lift distribution thus controlling the shock coalescence.

Yoo, Seung Yeun (Paul)↗

NASA NTRS1986

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach was applied to isolated wing geometries in order to facilitate code development. The TNS finite difference algorithm, zonal methodology, and code validation with experimental data is addressed. Also addressed are some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading edge flow gradients, massive shock induced separation, and stall. Furthermore, lift and drag coefficients were computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, Neal M.↗

NASA NTRSDate not supplied

Radiative Heat Transfer Capability Implemented in OpenNCC for Conjugate Heat Transfer Applications

Thermal efficiency of gas turbine engine increases as the temperature and pressure at the combustor increases. Consequently, the materials used inside a combustor must survive an increasingly challenging environment. For this reason, accurate assessment of heat transfer is crucial for combustor design. While all three modes of heat transfer are present inside a combustor, the focus of this paper is the thermal radiation. Radiative heat transfer in a gas turbine combustors are particularly interesting from three reasons. Firstly, the radiative heat loss from the combustion region may affect the emission performance. Secondly, the cooling air will protect the liner from convection but not necessary from radiation. Finally, it is less frequently incorporated in CFD analysis than other forms of heat transfer. In this work, radiative heat transfer using discrete ordinate method has been incorporated in OpenNCC (a publicly releasable version of the National Combustion Code) developed at NASA Glenn Research Center. Aside from massively parallel computation capability using MPI and the ability to utilize unstructured mesh, the current implementation includes two types of spectral models, namely, the weighted some of gray gas model and the full spectrum correlated k-distribution model. After presenting the theory and the strategy of implementation, results of validation cases for gray gas and spectral models will be presented. While the implementation of the radiation solver is intended for gas turbine application, the radiation solver can run independently from the convection/combustion solver and the same theory can be applied to other application.

OpenNCC↗

NASA NTRSDate not supplied

Radiative Heat Transfer Capability Implemented in OpenNCC for Conjugate Heat Transfer Applications

Thermal efficiency of gas turbine engine increases as the temperature and pressure at the combustor increases. Consequently, the materials used inside a combustor must survive an increasingly challenging environment. For this reason, accurate assessment of heat transfer is crucial for combustor design. While all three modes of heat transfer are present inside a combustor, the focus of this paper is the thermal radiation. Radiative heat transfer in a gas turbine combustors are particularly interesting from three reasons. Firstly, the radiative heat loss from the combustion region may affect the emission performance. Secondly, the cooling air will protect the liner from convection but not necessary from radiation. Finally, it is less frequently incorporated in CFD analysis than other forms of heat transfer. In this work, radiative heat transfer using discrete ordinate method has been incorporated in OpenNCC (a publicly releasable version of the National Combustion Code) developed at NASA Glenn Research Center. Aside from massively parallel computation capability using MPI and the ability to utilize unstructured mesh, the current implementation includes two types of spectral models, namely, the weighted some of gray gas model and the full spectrum correlated k-distribution model. After presenting the theory and the strategy of implementation, results of validation cases for gray gas and spectral models will be presented. While the implementation of the radiation solver is intended for gas turbine application, the radiation solver can run independently from the convection/combustion solver and the same theory can be applied to other application.

OpenNCC↗

NASA NTRSDate not supplied

Wall-Modeled Large-Eddy Simulations of a Swept Wing with Leading-Edge Ice

The aerodynamic performance of a swept wing derived from the Common Research Model wing with high-fidelity and smooth leading-edge ice shapes is evaluated using wall-modeled large-eddy simulations. Two mesh paradigms are considered within the Launch, Ascent, and Vehicle Aerodynamics framework: structured hybrid curvilinear body-fitted/immersed-boundary and unstructured Voronoi. The curvilinear approach models the effect of the ice on the flow through penalty terms and the Voronoi strategy includes the ice representation directly in the mesh.Aerodynamic loads, surface pressure profiles, and skin-friction streamlines are compared against experimental results collected at the Wichita State University wind tunnel at a Mach number of 0.18 and a Reynolds number per mean aerodynamic chord of 1.6 million. For the curvilinear simulations with high-fidelity ice, results are sensitive to spanwise mesh resolution near the leading edge, where insufficient spanwise resolution leads to a spanwise running vortexaft of the high-fidelity ice, which is partially removed with increasing spanwise resolution. For the Voronoi simulations with high-fidelity ice, refining the mesh led to good convergence towards the experimental results with the best case demonstrating a maximum discrepancy of three lift counts relative to the experiment across a range of angles of attack from about 5 to 24 degrees, validating the shrink-wrapping procedure used for the ice. For the smooth ice, the curvilinear approach consistently under-predicted the upper surface suction leading to an under-prediction in lift, but did not demonstrate the pronounced over-prediction in upper surface suction near the leading edge observed in the Voronoi simulations.

AATT↗

NASA NTRS2006

Time-Accurate, Unstructured-Mesh Navier-Stokes Computations with the Space-Time CESE Method

Application of the newly emerged space-time conservation element solution element (CESE) method to compressible Navier-Stokes equations is studied. In contrast to Euler equations solvers, several issues such as boundary conditions, numerical dissipation, and grid stiffness warrant systematic investigations and validations. Non-reflecting boundary conditions applied at the truncated boundary are also investigated from the stand point of acoustic wave propagation. Validations of the numerical solutions are performed by comparing with exact solutions for steady-state as well as time-accurate viscous flow problems. The test cases cover a broad speed regime for problems ranging from acoustic wave propagation to 3D hypersonic configurations. Model problems pertinent to hypersonic configurations demonstrate the effectiveness of the CESE method in treating flows with shocks, unsteady waves, and separations. Good agreement with exact solutions suggests that the space-time CESE method provides a viable alternative for time-accurate Navier-Stokes calculations of a broad range of problems.

Chang, Chau-Lyan↗

NASA NTRS1986

Transonic Navier-Stokes wing solutions using a zonal approach. Part 2: High angle-of-attack simulation

A computer code is under development whereby the thin-layer Reynolds-averaged Navier-Stokes equations are to be applied to realistic fighter-aircraft configurations. This transonic Navier-Stokes code (TNS) utilizes a zonal approach in order to treat complex geometries and satisfy in-core computer memory constraints. The zonal approach has been applied to isolated wing geometries in order to facilitate code development. Part 1 of this paper addresses the TNS finite-difference algorithm, zonal methodology, and code validation with experimental data. Part 2 of this paper addresses some numerical issues such as code robustness, efficiency, and accuracy at high angles of attack. Special free-stream-preserving metrics proved an effective way to treat H-mesh singularities over a large range of severe flow conditions, including strong leading-edge flow gradients, massive shock-induced separation, and stall. Furthermore, lift and drag coefficients have been computed for a wing up through CLmax. Numerical oil flow patterns and particle trajectories are presented both for subcritical and transonic flow. These flow simulations are rich with complex separated flow physics and demonstrate the efficiency and robustness of the zonal approach.

Chaderjian, N. M.↗

NASA NTRS1994

Effective conductivity of wire mesh reflectors for space deployable antenna systems

This report summarizes efforts to characterize the measurement of conductive mesh and smooth surfaces using proximity measurements for a dielectric resonator. The resonator operates in the HEM11 mode and is shown to have an evanescent field behavior in the vicinity of the sample surface, raising some question to the validity of measurements requiring near normal incidence on the material. In addition, the slow radial field decay outside of the dielectric resonator validates the sensitivity to the planar supporting structure and potential radiation effects. Though these concerns become apparent along with the sensitivity to the gap between the dielectric and the material surface, the basic concept of the material measurement using dielectric resonators has been verified for useful comparison of material surface properties. The properties, particularly loss, may be obtained by monitoring the resonant frequency along with the resonator quality factor (Q), 3 dB bandwidth, or the midband transmission amplitude. Comparison must be made to known materials to extract the desired data.

Davis, William A.↗

NASA NTRS2003

Modeling of Biological Fluid Systems

This study presents a detailed methodology for modeling and validating three- dimensional fluid flow in realistic reconstructed vasculature geometry. Optical scanned data from a sectioned stenotic lumen having -65% area constriction within an arterial vessel of 9 mm diameter is processed and converted into a finite-element mesh. Mass and momentum transfer equations within the reconstructed stenotic vessel with a-flow rate of 200 ml/rnin is solved using the Galarkin Finite Element formulation. The calculated velocities at several axial locations along the length of the vessel are compared with the Particle Image Velocimetry (PIV) measurements. The computation results are in agreement with the initial steady state PIV measurements. In addition, initial results from pulsatile flow computations at different time points of a pulse cycle will be presented.

Banerjee, Rupak↗

NASA NTRS2023

Unsteady RANS and Scale Resolving Simulations of Open Rotor Noise

Computational simulations using structured curvilinear overset grids with the Launch Ascent and Vehicle Aerodynamics (LAVA) framework are presented for predicting the aerodynamic and aeroacoustic behavior of a contra-rotating open rotor (CROR) propulsion system using a newly developed and computationally efficient sliding mesh technique. A comprehensive evaluation of two turbulence closure treatments is carried out as part of the scope of this work: Unsteady Reynolds-Averaged Navier-Stokes Simulation (URANS), and Hybrid RANS/LES (HRLES). The computed results are then validated against existing experimental measurements at both the nominal take-off and cruise flight conditions. To propagate the noise generated by the near-field CROR system, aeroacoustic analysis based on a frequency-domain permeable surface Ffowcs Williams-Hawkings (FW-H) approach is applied.

ARMD↗

NASA NTRS2023

Unsteady RANS and Scale Resolving Simulations of Open Rotor Noise

Computational simulations using structured curvilinear overset grids with the Launch Ascent and Vehicle Aerodynamics (LAVA) framework are presented for predicting the aerodynamic and aeroacoustic behavior of a contra-rotating open rotor (CROR) propulsion system using a newly developed and computationally efficient sliding mesh technique. A comprehensive evaluation of two turbulence closure treatments is carried out as part of the scope of this work: Unsteady Reynolds-Averaged Navier-Stokes Simulation (URANS), and Hybrid RANS/LES (HRLES). The computed results are then validated against existing experimental measurements at both the nominal take-off and cruise flight conditions. To propagate the noise generated by the near-field CROR system, aeroacoustic analysis based on a frequency-domain permeable surface Ffowcs Williams-Hawkings (FW-H) approach is applied.

ARMD↗

NASA NTRSDate not supplied

A Machine Learning Model for Solar Sail Shape Reconstruction Using Flight Data

Solar sail deformation leads to disturbance torques from solar radiation pressure, driving performance requirements for momentum management systems. For the Solar Cruiser technology demonstrator mission, we have developed a model leveraging neural network-based machine learning to derive sail shape characteristics. The model uses torque and attitude telemetry simulated from a reduced-order tensor model of the deformed sail mesh over a characterization sequence. The machine learning model predicts sail boom deflection with comparable accuracy to that of an onboard context camera. This model can discover sail shape with no additional mass or data downlink requirements, allowing for validation of sail force modeling assumptions using in flight data. The results from the project hold promise for the further implementation of machine learning techniques in solar sail telemetry analysis and control.

solar sail↗

NASA NTRSDate not supplied

A Machine Learning Model for Solar Sail Shape Reconstruction Using Flight Data

Solar sail deformation leads to disturbance torques from solar radiation pressure, driving performance requirements for momentum management systems. For the Solar Cruiser technology demonstrator mission, we have developed a model leveraging neural network-based machine learning to derive sail shape characteristics. The model uses torque and attitude telemetry simulated from a reduced-order tensor model of the deformed sail mesh over a characterization sequence. The machine learning model predicts sail boom deflection with comparable accuracy to that of an onboard context camera. This model can discover sail shape with no additional mass or data downlink requirements, allowing for validation of sail force modeling assumptions using in flight data. The results from the project hold promise for the further implementation of machine learning techniques in solar sail telemetry analysis and control.

solar sail↗

NASA NTRS1999

Implementation of Interaction Algorithm to Non-Matching Discrete Interfaces Between Structure and Fluid Mesh

This paper presents software for solving the non-conforming fluid structure interfaces in aeroelastic simulation. It reviews the algorithm of interpolation and integration, highlights the flexibility and the user-friendly feature that allows the user to select the existing structure and fluid package, like NASTRAN and CLF3D, to perform the simulation. The presented software is validated by computing the High Speed Civil Transport model.

Chen, Shu-Po↗

NASA NTRS1981

Stability of pseudospectral and finite-difference methods for variable coefficient problems

It is shown that pseudospectral approximation to a special class of variable coefficient one-dimensional wave equations is stable and convergent even though the wave speed changes sign within the domain. Computer experiments indicate similar results are valid for more general problems. Similarly, computer results indicate that the leapfrog finite-difference scheme is stable even though the wave speed changes sign within the domain. However, both schemes can be asymptotically unstable in time when a fixed spatial mesh is used.

Gottlieb, D.↗