Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mining waste”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Investigation and Analysis of Dolomite Dissolution in Variable Strength Systems Relevant to the WIPP

The Waste Isolation Pilot Plant (WIPP) was opened in 1999 as a solution to the long-term disposal of the nation's nuclear defense-generated transuranic (TRU) waste. The salt beds were recommended as the ideal location because they are free from flowing fresh water, easily mined, impermeable, and geologically stable. However, for performance assessment modeling, release scenarios must be considered. The most likely release scenario was determined to be human intrusion leading to direct and/or long-term brine release (US DOE 1995, US DOE 1996, Perkins et al., 1999). The focus of this research is the Rustler formation because it is located above the WIPP and is the most transmissive layer (Perkins et al., 1999). Objective: To determine the effect of chelating ligands ( e.g. EDTA) on dissolution of dolomite in high ionic strength systems. Do brines impact dolomite dissolution and how is it affected by EDTA binding with cations? By varying the ionic strengths, different brine conditions can be simulated similar to those in and around the Culebra member and evaluate trends of dissolved Ca and Mg in the aqueous phase from the quantified data. Conclusions: <2% of dolomite dissolved over one week at pH 8.5. Greater dissolution occurred at higher ionic strength and in the presence of NaCl with approximately 0.4 vs. 0.9% of Mg removed from dolomite in 0.1 and 1.0 M Na. Further, 0.3 vs. 0.9% of Mg was removed from dolomite in 1.0 M IS CaCl{sub 2} versus NaCl. EDTA increased dissolution of dolomite at low ionic strength due to its strong complexation affinity for Ca/Mg with slightly greater removal of Ca than Mg. Significant differences were not observed at high ionic strength due to the presence of large concentrations of competing cations (Na, Ca, Mg). Slightly higher concentrations of Ca were removed from dolomite than Mg after one week, suggesting either incongruent dissolution or release through ion exchange of Ca from trace mineral impurities. Further, when EDTA was present, it may have increased Ca removal due to its greater complexation for Ca than Mg. Environmental Implications: High ionic strength brines and low ionic strength solutions with organic ligands increase dissolution of dolomite. Due to the long half-lives of radionuclides in the TRU waste, it may be important to consider the long term impact of dolomite dissolution for potential release scenarios.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2025

Gulf Coast Basin CORE-CM Initiative (Final Report)

This report describes critical mineral/rare earth element resources, including Gulf Coast coal resources, and waste streams including coal ash from power plants, red mud from alumina processing, heavy mineral concentrates from sand mining industry, zeolite, graphite, and produced water with oil and gas.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Microanalytical Approaches to Characterizing REE in Appalachian Basin Underclays

The search for a reliable U.S. domestic source of rare earth elements (REE) is necessary to support the demand of advanced energy applications (e.g., catalysts, electronics, magnets). Sedimentary deposits may be sources for selectively recovering REE and critical metals—specifically the interbedded seat rock, or underclay, that underlies or forms the floor of a coal seam. This material is often a major component of coal waste fines and refuse and thus readily available. This study examines several Appalachian Basin underclays associated with actively mined coal seams as potential feedstocks for the REE. Multimodal microanalytical electron microscopy (SEM, FIB-SEM, EMPA) synchrotron-based µXRF, and image processing techniques are coupled with detailed elemental and mineral data to classify the 2D and 3D petrophysical properties of the materials. The REE contents of Appalachian Basin underclays were measured from 235–399 ppm and predominantly observed as discrete REE-bearing minerals such as monazite and xenotime on the order of 10–100 µm in size. These REE-bearing minerals typically accounted for less than 1% of the scanned areas and volumes under SEM and FIB-SEM analysis, with the exception of regions enriched in crandallite. Synchrotron-based µXRF elemental maps further identified several REE deposition environments in different underclays, including micro-scale (10–100 µm) light REEs co-localizing with Ca and P, micro-scale heavy REEs with Fe, and large-scale light REEs (>200 µm) co-localizing with Sr, Ba, Ca and P.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Sustainable Manufacturing and the Circular Economy

The manufacturing industry predominantly follows a linear model of production in which raw materials are mined or grown, transformed into manufactured goods, used for a period, and then discarded. However, this once-through flow of materials to manufactured products is not sustainable. Many high-grade ore bodies have been consumed, increasing the energy and material impacts per ton of mined material. At the other end of the cycle, there are challenges with the efficiency and effectiveness of our waste disposal system.

life cycle, ReX↗
DOE OSTI2025

Designing a repository in domal salt: The influence of design variants in different modelling environments

To understand the long-term environmental impact of disposing radioactive waste of in a deep geological repository and to optimise its design, performance assessments are used. In this study, four teams (COVRA, GRS, Quintessa, and DOE) modified the previously developed generic repository of DECOVALEX task F2 to identify commonalities and differences between the teams for specific changes in repository design. The teams tested six design modifications: (1) Replacing concrete abutments with run-of-mine salt; (2) Replacing the salt seal with a concrete abutment and using run-of-mine salt instead for the two concrete abutments in each drift seal; (3) Halving the size of the infrastructure area; (4) Using run-of-mine salt instead of gravel for backfilling the infrastructure area; (5) Disposal of spent nuclear fuel without the POLLUX-10 containers (6); Lower initial saturation of the spent nuclear fuel and vitrified waste disposal drifts. Despite different modelling strategies used, models agreed that a smaller infrastructure area has a limited effect on radionuclide transport. Responses to the absence of the two concrete abutments in each seal, the use of single large concrete abutments (200 m each), or the use of run-of-mine salt in the infrastructure area differ between teams due to differing modelling assumptions. Based on these results, the estimated efficacy of containment depends strongly on the model assumptions of each team. More specifically, it appears to depend on the compaction model used and therefore on the backfill material used in different areas of the repository. However, the drift seal appears to be a critical design element in all models, effectively limiting radionuclide transport by hydrologically disconnecting sections of the repository. Additional beneficial design choices include the use of dry salt in disposal drifts to limit radionuclide transport and reducing the infrastructure area costs and minimizing host rock damage.

DECOVALEX↗
DOE OSTI2024

Williston Basin CORE-CM Initiative Final Report

The University of North Dakota Energy & Environmental Research Center (EERC) is leading the Williston Basin Carbon Ore, Rare Earth, and Critical Minerals (CORE-CM) Initiative to drive the expansion and transformation of coal and coal-based resource usage within the Williston Basin to produce rare-earth elements (REEs), CMs, and nonfuel carbon-based products (CBPs). This project is the first phase in a long-term program and set the stage for future work by assessing resource, market, technology, and infrastructure knowledge; identifying knowledge gaps; developing a series of plans to be carried out in future work; and initiating stakeholder engagement. Composed of several tasks, the project sought to identify, characterize, and assess several necessary aspects vital to make this future work a reality. The project’s fundamental task was to characterize the Williston Basin CORE-CM resources. Over 2500 samples from multiple sources were utilized to begin the assessment. Several locations were identified in western North Dakota where sample analysis identified the total REE (TREE) concentration as being over 500 parts per million (ppm), which is at a concentration level that would be suitable to consider for mining and extraction. Current operating coal mines have sufficient concentrations of TREEs for consideration. However, the current data across the basin are still not adequate to fully characterize REE and CM content nor give reliable estimates of the total resource potential. Waste stream reuse was also considered, and several streams were identified which ranged from potential energy sources to chemicals to material wastes. This includes streams that result from oil and gas production. These streams are not fully characterized, and further data are needed before they can be accurately assessed. Infrastructure within the Williston Basin is suitable for expansion of a new industry to mine, extract, and concentrate REEs and CMs. The development of this industry will not only preserve many existing jobs in the coal-mining industry but produce many new jobs. The supply chain for REEs and CMs is currently controlled outside of the United States in nations such as China, but the potential to develop the supply chain within the basin is considered possible. Processing of the mined materials for REEs and CMs needs further research. The technology and knowhow exist outside of the United States, and within the country much of the knowledge has been lost and must be regained. To develop the supply chain and regain lost processing technology, the creation of technology innovation centers (TICs) is crucial. The Williston Basin contains several similar centers and entrepreneurial assistance for other industries that can be applied in the development of REE and CM innovation centers. Education to develop the new skill sets required is also needed. Outreach is important for the development of the REE and CM industry within the basin. Understanding throughout federal and state governments, state agencies, industry, and resource end users is vital for the industry to form and grow. Through this project these groups have been contacted through bulletins, presentations, webinars, and annual symposiums. The report is a summary of the work conducted and throughout refers to a series of appendixes which contain more thorough and specific information about each section.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2023

A Thermodynamic Model for Nd(III)–Sulfate Interaction at High Ionic Strengths and Elevated Temperatures: Applications to Rare Earth Element Extraction

Neodymium (Nd), a rare earth element (REE), is critical to numerous industries. Neodymium can be extracted from ore concentrates, waste materials, or recycled materials such as recycled Nd-Fe-B permanent magnets. In a standard process, concentrated sulfuric acid (H 2 SO 4 ) is used as an extraction/leaching agent. Therefore, knowledge of Nd(III)–sulfate interaction at high ionic strengths is important for optimization of the extraction process. In addition, sulfate is also a major species in natural surface waters and present in nuclear waste streams. Nd(III) has been used a chemical analog to trivalent actinides in nuclear waste research and development. Consequently, knowledge of Nd(III)-sulfate interactions is also impactful to the field of nuclear waste management. Here, in this study, we have developed a thermodynamic model that can describe the interaction of Nd(III) with sulfate to ionic strengths up to ~ 16.5 mol·kg –1 and to temperatures up to 100 °C. The model adopts the Pitzer formulation to describe activity coefficients of aqueous species. This model can be used to design and optimize a chemical process for REE recovery from ore concentrates, recycled materials, and acid mine drainage (AMD) and to understand the mobility of REEs and actinides in the environment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Disposal Concepts for a High-Temperature Repository in Shale.

Disposal of large, heat-generating waste packages containing the equivalent of 21 pressurized water reactor (PWR) assemblies or more is among the disposal concepts under investigation for a future repository for spent nuclear fuel (SNF) in the United States. Without a long (>200 years) surface storage period, disposal of 21-PWR or larger waste packages (especially if they contain high-burnup fuel) would result in in-drift and near-field temperatures considerably higher than considered in previous generic reference cases that assume either 4-PWR or 12-PWR waste packages (Jové Colón et al. 2014; Mariner et al. 2015; 2017). Sevougian et al. (2019c) identified high-temperature process understanding as a key research and development (R&D) area for the Spent Fuel and Waste Science and Technology (SFWST) Campaign. A two-day workshop in February 2020 brought together campaign scientists with expertise in geology, geochemistry, geomechanics, engineered barriers, waste forms, and corrosion processes to begin integrated development of a high-temperature reference case for disposal of SNF in a mined repository in a shale host rock. Building on the progress made in the workshop, the study team further explored the concepts and processes needed to form the basis for a high-temperature shale repository reference case. The results are described in this report and summarized..

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2020

Pre-Excavation Activities for the Long Baseline Neutrino Facility Far Site

The Long Baseline Neutrino Facility Far Site at the Sanford Underground Research Facility in Lead, South Dakota will house four large detector tanks located deep underground. Construction of the supporting infrastructure required for this project is already underway including installation of a waste rock conveyance system including, but not limited to, a grizzly, skip loader, crusher, belt conveyor, and rehab of existing mine drifts and ore passes. This paper will discuss the design and construction of these pre-excavation works, and the overall project schedule as it closes in on commencement of mass excavation activities.

Pollock, Seth↗
DOE OSTI2024

Recovery of Oxpure 612C-50 Coconut Carbon Particles Using Bump Arrays

Cyanide is used to leach gold from crushed ore (solid matrix) into a gold cyanide solution. The gold is extracted from the cyanide solution by adsorption onto activated carbon. The gold extraction process occurs when the activated coconut carbon is placed into tanks that contain the gold cyanide solution either in a batch process or into a continuous flow circuit. The coconut carbon is then removed from the solution for gold recovery. The use of the mesofluidic separation system (a deterministic lateral displacement system) can significantly reduce costs and waste generated from the process of removing the coconut carbon from the solution. In the coconut carbon recovery process used at many gold mines in Nevada, the gold is attached to carbon particles that are still in the cyanide liquor. The mesofluidic system can rapidly remove the gold bearing carbon particles from the cyanide liquor quickly and with no operating costs. The benefits include: • Reduce operational costs related to filtration and hydro-cyclones • Reduced acid usage for the elution gold stripping phase as only 25% of the fluids will follow the carbon particles to the final express lane when two mesofluidic systems are used in series This alternative particle removal techniques would be advantageous. A promising technique for removing larger particles from slurries is mesofluidic separation, similar to deterministic lateral displacement arrays or “bump” arrays [1] but operates at much larger flow rates. As described by Pease, et al. [2], “Bump arrays in deterministic lateral displacement devices separate large particles from small particles using arrays of staggered posts. Large particles, defined as those with radii larger than the distance between the edge of a post and the stagnation streamline from the next downstream post, must bump toward one side of the device, whereas particles smaller than this distance slalom from entrance to exit without net lateral displacement.” Unlike filters or sieves, the posts in the arrays that cause separation do not block or occlude particle flow but work because particles go around the posts. Unlike hydrocyclones separation, separation is not driven by particle density, because gravitational forces are unimportant to mesofluidic separation. Burns, et al., and Pease, et al., have shown that particles may be separated from complex suspensions, under turbulent flow conditions, and at industrially important flow rates [3-5]. They have also recently shown that mesofluidic devices may be arranged in series to increase separation performance [6]. In this paper, we evaluate the mesofluidic system for the separation of commercial OxPure GR 612 Charred Coconut shell particles as a proof of principle test for the rapid separation using the 1500 micron cut mesofluidic separator. We first describe the experimental system and conditions. We then present the experimental results. [1] Huang, L.R., E.C. Cox, R.H. Austin, J.C. Sturm. 2004. Continuous particle separation through deterministic lateral displacement. Science, 304, 987–990. https://doi.org/10.1126/science.1094567. [2] Pease L.F., J.A. Bamberger, C.A. Burns, and M.J. Minette. 2021. Large Particle Separation from Non-Newtonian Slurries using Bump Arrays. In Proceedings of the ASME 2021 Fluids Engineering Division Summer Meeting FEDSM2021-65904, V003T08A023. New York, New York: ASME. doi:10.1115/FEDSM2021-65904 [3] Burns C.A., T.G. Veldman, J. Serkowski, R.C. Daniel, X.-Y. Yu, M.J. Minette, L.F. Pease. 2021. Mesofluidic separation versus dead-end filtration. Separation and Purification Technology, 254, 117256. https://doi.org/10.1016/j.seppur.2020.117256. [4] Pease L.F., J.E. Serkowski, T.G. Veldman, J. Williams, X.-Y. Yu, M.J. Minette, J.A. Bamberger, C.A. Burns. 2021. Can Bump Arrays Separate Particles from Turbulent Flows?. In Proceedings of the ASME 2021 Fluids Engineering Division Summer Meeting FEDSM2021-67696, V003T08A024. New York, New York: ASME. doi:10.11

mesofluidic separation, slurry, bump array↗
DOE OSTI2021

Critical review of functionalized silica sorbent strategies for selective extraction of rare earth elements from acid mine drainage

We report the ubiquitous and growing global reliance on rare earth elements (REEs) for modern technology and the need for reliable domestic sources underscore the rising trend in REE-related research. Adsorption-based methods for REE recovery from liquid waste sources are well-positioned to compete with those of solvent extraction, both because of their expected lower negative environmental impact and simpler process operations. Functionalized silica represents a rising category of low cost and stable sorbents for heavy metal and REE recovery. These materials have collectively achieved high capacity and/or high selective removal of REEs from ideal solutions and synthetic or real coal wastewater and other leachate source. These sorbents are competitive with conventional materials, such as ion exchange resins, activated carbon; and novel polymeric materials like ion-imprinted particles and metal organic frameworks (MOFs). This critical review first presents a data mining analysis for rare earth element recovery publications indexed in Web of science, highlighting changes in REE recovery research foci and confirming the sharply growing interest in functionalized silica sorbents. A detailed examination of sorbent formulation and operation strategies to selectively separate heavy (HREE), middle (MREE), and light (LREE) REEs from the aqueous sources is presented. Selectivity values for sorbents were largely calculated from available figure data and gauged the success of the associated strategies, primarily: (1) silane-grafted ligands, (2) impregnated ligands, and (3) bottom-up ligand/silica hybrids. These were often accompanied by successful co-strategies, especially bite angle control, site saturation, and selective REE elution. Recognizing the need to remove competing fouling metals to achieve purified REE “baskets,” we highlight techniques for eliminating these species from acid mine drainage (AMD) and suggest a novel adsorption-based process for purified REE extraction that could be adapted to different water systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Reveal of Uranium Bioremediation Mechanisms by Bacillus Species through Proteomics Studies

Radionuclides, such as Uranium (U) and heavy metals continue to pose threats to the ecosystem health and processes at the Department of Energy (DOE) managed, Savannah River Site (SRS), located along the Savannah River near Aiken, SC. Such co-contaminated environments are difficult to remediate using conventional excavation and disposal or pump-and-treat approaches. Globally, more than 109 tons of uranium contaminated areas pose a long term threat to human and ecological health. Even with presented low concentrations in the brain, central nervous effects are still observed. Uranium and depleted uranium (DU) have long term effects on the kidneys. Some small general health effects include severe headaches and breathing problems. Uranus ions are toxic to living cells because they inhibit metabolism of carbohydrates by blocking ATP binding sites. Bioremediation by microorganisms represents an alternative solution, which is advantageous because of the possibility of biosorbent regeneration, cost-effectiveness, increased metal removal and easy recovery of some valuable metals. Bacillus sp. bacterium was previously used in the bioremediation of heavy metals in coal mine run off waters of SRS. However, its ability to bioremediate uranium was unknown so far. Hence, in the present study, uranium bioremediation by Bacillus sp. bacterium was investigated. The mechanism of bioremediation was also revealed through proteomics studies. Heavy metals contamination poses a serious threat to water, soil and human health. Soil and water are contaminated due to excessive exploitation of uranium mines for generation of nuclear energy and weaponry. It is not degradable easily and persist in soil and water for a long period of time due to its long half- life. Savannah river site (SRS) is one of the uranium contaminated sites. The physical or chemical remediation techniques are costly and complex. Microbial system approaches with competent bacteria has received increased attention due to its adaptability in various environmental matrices and cost effectiveness. However, even though there are multiple suggested pathways (F1), the specific mechanisms that drive this behavior are still unclear, especially with popular microorganisms such as Bacillus species. In a previous research (Ibeanusi et al, 2003) Bacillus sp. was shown to detoxify and precipitate a variety of heavy metals in coal pile runoff waters of SRS site. Additionally, genomic analysis demonstrated that this microorganism posses multiple attributes for chemical transport regulation and metabolic pathways. U remediation occurs during the first 20 hours of exposure. During this time period, Bacillus sp. may work primarily under two mechanisms - sorption and accumulation. These two mechanisms simultaneously work to protect the microorganism from high concentrations. Figure 10 demonstrates that certain proteins are up regulated and down regulated under extreme stressful conditions. Membrane fraction proteins were up regulated. Cytosolic fraction proteins were down regulated. This protein information coincides with the adsorption behavior. Bacillus sp. is a good candidate for U remediation at various concentrations.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2021

Middle Kittanning Coal Waste and Underclay as an Alternative Rare Earth Elements Feedstock

In order to secure domestic sources of rare earth elements (REE) from coal related materials, there must be validation of representative feedstocks. Actively producing coal mines that target the Middle Kittanning coal seam in the Appalachian Basin were compiled. These mines were cross-referenced with publicly available geochemical data such as the U.S. Geological Survey (USGS) Earth Mapping Resources Initiative geochemical data along with samples evaluated and characterized by the National Energy Technology Laboratory (NETL). This work evaluated the extent of elevated Middle Kittanning underclay concentrations of REE in comparison to other underclay formations. Therefore, further up-scaling of research associated with the separation and extraction of REE and other critical minerals can be beneficial to utilizing domestic REE supplies for various technology sectors, to include energy, biomedical, and defense. Numerous current active mines targeting the Middle Kittanning coal seam represent a geographically significant opportunity for shared feedstocks and collaborations to further understand the role of Middle Kittanning underclay as a critical mineral feedstock.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2020

Cultivation and Use of Acidithiobacillus ferrooxidans in Tellurium Biorecovery

The use of Acidithiobacillus ferrooxidans, Thiobacillus thiooxidans, and other chemoautotrophic microbes in bioleaching have been implemented in a variety of processes.1 In industry, bioleaching has been studied for its potential to extract valuable metals from low grade ores that would otherwise be cost prohibitive to recover.2 Other applications of bioleaching include the ability of certain microbes to detoxify waste products and even heavy metal contaminated soils.3 Another potential application for such bio-oxidative microbial activity is the extraction of tellurium (Te) from mine tailings, a low-cost abundant resource. Tellurium is one of the least common elements on Earth; it is found in the planetary crust at about 1 µg/kg, a rarity most comparable to that of platinum.4 A major use of Te in the U.S. is in cadmium-telluride (CdTe) solar panels5. Te is primarily imported into the U.S. from Canada, and it is usually recovered as a byproduct of copper refining.6 Since CdTe photovoltaic (PV) cells are the most efficient, cost-effective, and environmentally friendly PV chemistry, the renewables market has seen an increased demand for CdTe PV cells causing some concerns about sustainability and the limited global availability of Te. Acidithiobacillus ferroxidans is a microorganism that can oxidize iron and sulfur to produce ferric iron and sulfuric acid, and it is possible that it could also solubilize Te from sulfidic mine tailings. In this project, different media for growth of A. ferroxidans were evaluated, and a plan for testing the ability of A. ferroxidans to leach Te from mine tailings was developed. Initial characterization of A. ferroxidans cultures grown in the presence of copper tailings suggests that conditions suitable for Te bioleaching can be established.

60 APPLIED LIFE SCIENCES↗
DOE OSTI2023

Geochemical characterization of lithium deposition in fossil energy wastes

Lithium is a critical mineral used in rechargeable batteries for electric vehicles (EVs) and future modernization of electric grids with sensitive supply chains that are subject to volatility. Therefore, methods to recover lithium from domestic unconventional sources are actively being pursued in the United States. Herein, we report on the lithium recovery potential from four fossil energy waste feedstocks: oil and gas drill cuttings (sample number n = 16); oil and gas produced waters (n > 200) from Marcellus, Bakken and Permian basins; coal byproducts (n>20), such as coal ash; and acid mine drainage treatment solids (AMD solids). Select solid samples underwent sequential extraction to explore lithium hosting phases and simple organic and inorganic acid extraction to explore lithium recovery potential. Our preliminary results found lithium concentrations up to 440 mg/kg in select AMD treatment solids and up to 300 mg/L in Marcellus Shale produced waters, demonstrating these sources have lithium yield potentials comparable to conventionally mined lithium ores and brines. Sequential extractions revealed that lithium is mostly associated with clay and silicate phases in shale drill cuttings, whereas lithium resides in Fe,Mn-oxide reducible phases in AMD solids. Further, the lithium content in produced waters has a strong linear relationship with total dissolved solid (TDS) levels in three separate oil and gas basins. At the same TDS level, Marcellus Shale produced waters contain more lithium compared to Bakken Shale and Permian Basin waters, with higher percentages of Ca and Mg, major cations that might impact lithium recovery efficiencies. Our study demonstrates the heterogeneity of lithium hosts from different fossil energy wastes. Characterization results will inform future lithium recovery from these different feedstocks.

Stuckman, Mengling↗
DOE OSTI2024

Innovating the next generation of commercial smart building software

Nearly 30% of commercial building energy use is wasted due to equipment faults and HVAC controls problems. The result is increased emissions, compromised comfort and productivity, and less reliable coordination of building power needs with a clean grid. The energy impact alone represents $17 billion in potential savings. Today’s smart building software provides a robust solution to address these operational deficiencies. Energy management and information systems (EMIS) are saving up to 9% on average, with two-year paybacks. They are being incorporated into energy management processes, commissioning services, and utility programs. As effective as they are, two barriers prevent even deeper benefits; limited personnel to fix problems once they are identified, and the expense and time to manually implement changes in control systems. In partnership with the research community, the EMIS industry is developing new capabilities to overcome these barriers. Moving beyond siloed products for either fault detection and diagnostics, or optimal control, these new capabilities empower users to not only automatically identify faults, but also to push corrective action, and control improvements to their buildings. In this paper, several areas for enhancements are documented: ‘one-time’ correction of faults such as setpoints, schedules, and economizer lockouts; short-term active testing for automated proportional integral derivative (PID) loop tuning and functional testing; and continuous supervisory control for demand flexibility and year-round efficiency. Results are presented from a pair of partner implementations out of a dozen providers integrating these enhancements into their products, including field tests from across the country, and insights into operator acceptance and integration into operations and maintenance practices.

Casillas, Armando↗
DOE OSTI2026

Extracting Critical Metals from Authentic Bauxite Residue

Securing domestic sources of critical minerals (CM) is paramount to ensuring a robust and self-sustaining technology infrastructure. Utilizing untapped non-conventional sources, like acid mine drainage, coal ash, bauxite residue/red mud, and more is an emerging approach that addresses this national concern while identifying new value-added pathways originating from waste streams. Red mud is a byproduct of the Bayer process that produces alumina and contains a wealth of CM – 50 µg/g Ga, 2.9 mg/g total rare earth elements plus yttrium, 12 mg/g Mn, 58 mg/g Al, and others. About 170 MM tonnes of red mud are co-produced annually alongside the 142 MM tonnes of alumina generated, highlighting the abundancy of this feedstock. In this work, different strategies were explored for extracting CM from authentic bauxite residue that involve thermal heating, microwave heating, and sonication all with different acids and buffers. CM recovery was then explored one step further by testing the adsorption of the extracted metals onto NETL’s Multi-functional Sorbent Technology (MUST). Microwave treatment of red mud proved the most effective CM extraction, whereas sonication was less desirable due to scale-up concerns. Successful recovery of CM from this leachate with MUST supports further studies toward optimizing the overall process.

bauxite residue↗