Search NASA⌕ Search

SEARCH · Search NASA

Results for “Mixture experiment”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Recent Advances In Science Support For Isolated Droplet Combustion Experiments

In a joint program involving Prof. F.A. Williams of the University of California, San Diego and Dr. V. Nayagam of the National Center for Microgravity Research, the combustion characteristics of isolated liquid fuel droplets of n-heptane, n-decane, methanol, methanol-water, ethanol and ethanol-water having initial diameters between about 1 mm and 6 mm continues to be investigated. The objectives of the work are to improve fundamental knowledge of droplet combustion dynamics for pure fuels and fuel-water mixtures through microgravity experiments and theoretical analyses. The Princeton contributions support the engineering design, data analysis, and data interpretation requirements for the study of initially single component, spherically symmetric, isolated droplet combustion studies through experiments and numerical modeling. UCSD contributions are described in a companion communication in this conference. The Princeton effort also addresses the analyses of Fiber Supported Droplet Combustion (FSDC) experiments conducted with the above fuels and collaborative work with others who are investigating droplet combustion in the presence of steady convection. A thorough interpretation of droplet burning behavior for n-heptane and n-decane over a relatively wide range of conditions also involves the influences of sooting on the combustion behavior, and this particular aspect on isolated burning of droplets is under consideration in a collaborative program underway with Drexel University. This collaboration is addressed in another communication at this conference. The one-dimensional, time-dependent, numerical modeling approach that we have continued to evolve for analyzing isolated, quiescent droplet combustion data has been further applied to investigate several facets of isolated droplet burning of simple alcohols, n-heptane, and n-decane. Some of the new results are described below.

Dryer, F. L.↗

Phase, morphology, elemental composition, and formation mechanisms of biogenic and abiogenic Fe-Cu-sulfide nanoparticles: A comparative study on their occurrences under anoxic conditions

In this paper, we report on a systematic study on the physicochemical attributes of synthetic Fe-Cu-sulfide nanoparticles (NPs) precipitated under conditions similar to the anoxic, low temperature aqueous, sedimentary, soil and subsurface environments where these NPs have been repeatedly identified. Characterizing the basic attributes of these NPs is the first step in understanding their behaviors in various processes including in the bio-availability of essential and toxic metals, environmental remediation and resource recovery. All experiments are performed in the presence and absence of the sulfate-reducer Desulfovibrio vulgaris to elucidate biological controls on NP formation. First, the single-metal endmember NPs are determined by precipitation in solution containing either aqueous Fe(II) or Cu(II). Limited differences are observed between biogenic and abiogenic precipitates aged for up to one month; the Fe-only experiments resulted in 4-10 nm mackinawite (FeS) NPs that aggregate to form nanosheets up to ~1,000 nm in size, while the Cu-only experiments resulted in mixtures of covellite (CuS) NPs comprised of <10 nm fine nanocrystals, 20-40 x 6-9 nm nanorods and ~30 nm nanoplates. The crystal sizes of biogenic mackinawite and covellite are respectively larger and smaller than their abiogenic counterparts, indicating a mineral-specific response to biological presence. Structural defects are observable in the fine nanocrystals and nanorods of covellite in both biogenic and abiogenic experiments, indicative of intrinsic NP instability and formation mechanism via particle attachment. In contrast, covellite nanoplates are defect-free, indicating high stability and potentially rapid recrystallization following particle attachment. Next, mixed-metal sulfide NPs are precipitated at variable initial aqueous Fe-to-Cu ratios (2:1, 1:1 and 1:5). With increasing ratio of Fe-to-Cu, Fe-rich covellite, nukundamite (Cu 5.5 FeS 6.5 ), chalcopyrite (CuFeS 2 ), and Cu-rich mackinawite are formed. The Fe-rich covellite NPs are larger (100-200 nm) than covellite precipitated in the absence of Fe, indicating a role for Fe in promoting crystal growth. Chalcopyrite and nukundamite are formed through incorporation of Fe into precursor covellite NPs while retaining the original crystal morphology, as confirmed by doping a covellite suspension with aqueous Fe(II), resulting in the formation of chalcopyrite and nukundamite within days. Additionally, in the biological systems we observe the recrystallization of mackinawite to greigite (Fe 3 S 4 ) after six months of incubation in the absence of Cu, and the selective formation of chalcopyrite and nukundamite at lower initial Fe-to-Cu ratios compared to abiotic systems. These observations are consistent with NP precipitation that are influenced by the distinct (sub)micro-environments around bacterial cells compared to the bulk solution. Lastly, comparative TEM analyses indicate that the synthetic NPs are morphologically similar to NPs identified in natural environments, opening ways to studying behaviors of natural NPs using experimental approaches.

36 MATERIALS SCIENCE↗

Disturbing effect of free hydrogen on fuel combustion in internal combustion engines

Experiments with fuel mixtures of varying composition, have recently been conducted by the Motor Vehicle and Airplane Engine Testing Laboratories of the Royal Technical High School in Berlin and at Fort Hahneberg, as well as at numerous private engine works. The behavior of hydrogen during combustion in engines and its harmful effect under certain conditions, on the combustion in the engine cylinder are of general interest. Some of the results of these experiments are given here, in order to elucidate the main facts and explain much that is already a matter of experience with chauffeurs and pilots.

Riedler, A↗

Sequestration of CO2 in Mixtures of Bauxite Residue and Saline Wastewater

Experiments were conducted to explore the concept of beneficially utilizing mixtures of caustic bauxite residue slurry (pH 13) and produced oil-field brine to sequester carbon dioxide from flue gas generated from industrial point sources. Data presented herein provide a preliminary assessment of the overall feasibility of this treatment concept. The Carbonation capacity of bauxite residue/brine mixtures was considered over the full range of reactant mixture combinations in 10% increments by volume. A bauxite residue/brine mixture of 90/10 by volume exhibited a CO2 sequestration capacity of greater than 9.5 g/L when exposed to pure CO2 at 20 °C and 0.689 MPa (100 psig). Dawsonite and calcite formation were predicted to be the dominant products of bauxite/brine mixture carbonation. It is demonstrated that CO2 sequestration is augmented by adding bauxite residue as a caustic agent to acidic brine solutions and that trapping is accomplished through both mineralization and solubilization. The product mixture solution was, in nearly all mixtures, neutralized following carbonation. However, in samples (bauxite residue/brine mixture of 90/10 by volume) containing bauxite residue solids, the pH was observed to gradually increase to as high as 9.7 after aging for 33 days, suggesting that the CO2 sequestration capacity of the samples increases with aging. Our geochemical models generally predicted the experimental results of carbon sequestration capacities and solution pH.

Dilmore, R M↗

Investigation of nitrogen dilution effects on the laminar burning velocity and flame stability of syngas fuel at atmospheric condition

The objective of this investigation was to study the effect of dilution with nitrogen on the laminar burning velocity and flame stability of syngas fuel (50% H{sub 2}-50% CO by volume)-air (21% O{sub 2}-79% N{sub 2} by volume) mixtures. The syngas fuel composition considered in this work comprised x% N{sub 2} by volume and (100-x)% an equimolar mixture of CO and H{sub 2}. The proportion x (i.e., %N{sub 2}) was varied from 0 to 60% while the H{sub 2}/CO ratio was always kept as unity. Spherically expanding flames were generated by centrally igniting homogeneous fuel-air gas mixtures in a 40-L cylindrical combustion chamber fitted with optical windows. Shadowgraphy technique with a high-speed imaging camera was used to record the propagating spherical flames. Unstretched burning velocity was calculated following the Karlovitz theory for weakly stretched flames. Also, Markstein length was calculated to investigate the flame stability conditions for the fuel-air mixtures under consideration. Experiments were conducted for syngas fuel with different nitrogen proportions (0-60%) at 0.1 MPa (absolute), 302{+-}3K, and equivalence ratios ranging from 0.6 to 3.5. All the measurements were compared with the numerical predictions obtained using RUN-1DL and PREMIX with a contemporary chemical kinetic scheme. Dilution with nitrogen in different proportions in syngas resulted in (a) decrease in laminar burning velocity due to reduction in heat release and increase in heat capacity of unburned gas mixture and hence the flame temperature, (b) shift in occurrence of peak laminar burning velocity from {phi}=2.0 for 0% N{sub 2} dilution to {phi}=1.4 for 60% N{sub 2} dilution, (c) augmentation of the coupled effect of flame stretch and preferential diffusion on laminar burning velocity, and (d) shift in the equivalence ratio for transition from stable to unstable flames from {phi}=0.6 for 0% N{sub 2} dilution to {phi}=1.0 for 60% N{sub 2} dilution. The present work also indicated that if the fuel mole fraction in the wide range of fuel-air mixtures investigated is less than 22%, then those fuel mixtures are in the unstable regime with regard to preferential diffusion. (author)

10 SYNTHETIC FUELS↗

Marangoni Effects on Near-Bubble Microscale Transport During Boiling of Binary Fluid Mixtures

In earlier investigations, Marangoni effects were observed to be the dominant mechanism of boiling transport in 2-propanol/water mixtures under reduced gravity conditions. In this investigation we have examined the mechanisms of binary mixture boiling by exploring the transport near a single bubble generated in a binary mixture between a heated surface and cold surface. The temperature field created in the liquid around the bubble produces vaporization over the portion of its interface near the heated surface and condensation over portions of its interface near the cold surface. Experiments were conducted using different mixtures of water and 2-propanol under 1g conditions and under reduced gravity conditions aboard the KC135 aircraft. Since 2-propanol is more volatile than water, there is a lower concentration of 2-propanol near the hot surface and a higher concentration of 2-propanol near the cold plate relative to the bulk quantity. This difference in interface concentration gives rise to strong Marangoni effects that move liquid toward the hot plate in the near bubble region for 2-propanol and water mixtures. In the experiments in this study, the pressure of the test system was maintained at about 5 kPa to achieve the full spectrum of boiling behavior (nucleate boiling, critical heat flux and film boiling) at low temperature and heat flux levels. Heat transfer data and visual documentation of the bubble shape were extracted from the experimental results. In the 1-g experiments at moderate to high heat flux levels, the bubble was observed to grow into a mushroom shape with a larger top portion near the cold plate due to the buoyancy effect. The shape of the bubble was somewhat affected by the cold plate subcooling and the superheat of the heated surface. At low superheat levels for the heated surface, several active nucleation sites were observed, and the vapor stems from them merged to form a larger bubble. The generation rate of vapor is moderate in this regime and the bubble shape is cylindrical in appearance. In some instances, the bubble interface appeared to oscillate. At higher applied heat flux levels, the top of the bubble became larger, apparently to provide more condensing interface area adjacent to the cold plate. Increasing the applied heat flux ultimately led to dry-out of the heated surface, with conditions just prior to dryout corresponding to the maximum heat flux (CHF). A more stable bubble was observed when the system attained the minimum heat flux (for film boiling). In this regime, most of the surface under the bottom of the bubble was dry with nucleate boiling sometimes occuring around the contact perimeter of the bubble at heated surface. Different variations (e.g. gap between two plates, molar concentration of the liquid mixture) of the experiments were examined to determine parametric effects on the boiling process and to determine the best conditions for the KC135 reduced gravity tests. Variation of the gap was found to have a minor impact on the CHF. However, reducing the gap between the hot and cold surface was observed to significantly reduce the minimum heat flux for fixed molar concentration of 2-propanol. In the reduced gravity experiments aboard the KC135 aircraft, the bubble formed in the 6.4 mm gap was generally cylindrical or barrel shaped and it increased its extent laterally as the surface superheat increased. In reduced gravity experiments, dryout of the heated surface under the bubble was observed to occur at a lower superheated temperature than for 1g conditions. Observed features of the boiling process and heat transfer data under reduced gravity will be discussed in detail. The results of the reduced gravity experiments will also be compared to those obtained in comparable 1g experiments. In tandem with the experiments we are also developing a computational model of the transport in the liquid surrounding the bubble during the boiling process. The computational model uses a level set method to model motion of the interface. It will incorporate a macroscale treatment of the transport in the liquid gap between the surfaces and a microscale treatment of transport in the regions between the bubble interface and the solid surfaces. The features of the model will be described in detail. Future research directions suggested by the results to date will also be discussed.

V. Carey↗

Marangoni Effects in the Boiling of Binary Fluid Mixtures

Results of very recent experimental studies indicate that during nucleate boiling in some binary mixture, Marangoni effects augment the gravity driven flow of liquid towards the heated surface. With gravity present, it is impossible to separate the two effects. The reduced gravity environment gives an unique opportunity to explore th role of Marangoni effects on the boiling mechanisms free of gravitational body forces that obscure the role of such effects. However, recent experimental results suggest that under reduced gravity conditions, Marangoni effects is the dominant mechanism of vapor-liquid exchange at the surface for some binary mixture. To further explore such effects, experiments have been conducted with water/2-propanol mixtures at three different concentrations under normal gravity with different orientations of the heater surface and under reduce gravity aboard the DC-9 aircraft at NASA Lewis Research Center. The system pressure was sub atmospheric (approx. 8 kP at 1g(n)) and the bulk liquid temperature varied from low subcooling to near saturation. The molar concentrations of 2-propanol tested were 0.015, 0.025, and 0.1. Boiling curves were obtained both for high gravity (approx. 2g(n)) and reduce gravity (approx. 0.01g(n)). For each concentration of 2-propanol, the critical heat flux has been determined in the flight experiments only for reduced gravity conditions. Comparison of boiling curves and CHF obtained under l-g(n) an reduced gravity indicates that boiling mechanism in this mixtures is nearly independent of gravity. The results also indicate that the Marangoni mechanism is strong enough in these mixtures to sustain the boiling under reduced gravity conditions.

Ahmed, Sayeed↗

Fundamental Studies on Poly(2-oxazoline) Side Chain Isomers Using Tandem Mass Spectrometry and Ion Mobility-Mass Spectrometry

When polymer mixtures become increasingly complex, the conventional analysis techniques become insufficient for complete characterization. Mass spectrometric techniques can satisfy this increasing demand for detailed sample characterization. Even though isobaric polymers are indistinguishable using simple mass spectrometry (MS) analyses, more advanced techniques such as tandem MS (MS/MS) or ion mobility (IM) can be used. Here, we report proof of concept for characterizing isomeric polymers, namely poly(2-n-propyl-2-oxazoline) (Pn-PrOx) and poly(2-isopropyl-2-oxazoline) (Pi-PrOx), using MS/MS and IM-MS. Pi-PrOx ions lose in intensity at higher accelerating voltages than Pn-PrOx ions during collision-induced dissociation (CID) MS/MS experiments. A Pn/i-PrOx mixture could also be titrated using survival yield calculations of either precursor ions or cation ejection species. IM-MS yielded shape differences in the degree of polymerization (DP) regions showing the structural rearrangements. Combined MS techniques are thus able to identify and deconvolute the molar mass distributions of the two isomers in a mixture. Finally, the MS/MS and IM-MS behaviors are compared for interpretation. .

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Laboratory measurements of geometrical effects in the x-ray emission of optically thick lines for ICF diagnostics

Understanding the effects of radiative transfer in High Energy Density Physics experiments is critical for the characterization of the thermodynamic properties of highly ionized matter, in particular in Inertial Confinement Fusion (ICF). In this paper, we report on non-Local Thermodynamic Equilibrium experiments on cylindrical targets carried out at the Omega Laser Facility at the Laboratory for Laser Energetics, Rochester NY, which aim to characterize these effects. In these experiments, a 50/50 mixture of iron and vanadium, with a thickness of 2000 Å and a diameter of 250 μm, is contained within a beryllium tamper, with a thickness of 10 μm and a diameter of 1000 μm. Each side of the beryllium tamper is then irradiated using 18 of the 60 Omega beams with an intensity of roughly 3 × 10 14 W cm -2 per side, over a duration of 3 ns. Spectroscopic measurements show that a plasma temperature on the order of 2 keV was produced. Imaging data show that the plasma remains cylindrical, with geometrical aspect ratios (quotient between the height and the radius of the cylinder) from 0.4 to 2.0. The temperatures in this experiment were kept sufficiently low (~1–2 keV) so that the optically thin Li-like satellite emission could be used for temperature diagnosis. This allowed for the characterization of optical-depth-dependent geometric effects in the vanadium line emission. Lastly, simulations present good agreement with the data, which allows this study to benchmark these effects in order to take them into account to deduce temperature and density in future ICF experiments, such as those performed at the National Ignition Facility.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Experimental study of the application of rotating fluidized beds to particle separation

Rotating fluidized beds provide a unique opportunity to exploit fluidization under higher particle forces. The centripetal force in a rotating fluid bed is typically on the order of 10 times the force of gravity. Since the force keeping the particles in the unit is larger, the drag force can also be larger, allowing for higher gas and slip velocities. This operating regime provides intensified gas-solids contact through higher mass transfer, heat transfer, gas throughput, and bubble suppression. One application for using a rotating fluidized bed is in Chemical Looping Combustion (CLC). When solid fuels are used, oxygen carrier and ash are mixed in the process. In order to maintain high carbon capture efficiencies and recyclability of the oxygen carrier, the ash needs to be separated from the oxygen carrier. This separation can be done aerodynamically since the oxygen carrier is larger and heavier than the ash. It is theorized that rotating fluidized beds could improve both the gas-solid and solid-solid separation process efficiency and throughput as compared to conventional fluidized beds. A 43 cm diameter, 2.5 cm long vortex chamber has been designed and constructed to investigate the application to particle separation. A series of experiments have been performed to investigate the separation of different binary mixtures of solids. These experiments demonstrate the use of a rotating fluidized bed for high-G intensified particle separation that can be combined with high-G intensified gas-solids contact and gas-solids separation.¼

01 COAL, LIGNITE, AND PEAT↗

Reburning of Animal Waste Based Biomass with Coal for NO x Reduction, Part I: Feedlot Biomass (FB) and Coal:FB Blends

Cattle biomass (CB or manure from cattle) is proposed as reburn fuel under slightly fuel-rich conditions. The CB includes wastes from cattle feedlots (cattle grown in feedlots to slaughter weights of 450–640 kg) termed as Feedlot Biomass (FB) and cattle wastes from dairy farms termed as Dairy Biomass (DB). NOx emissions from coal-fired power plants can be reduced by using pure CB and Coal:CB mixtures as reburn fuels (10~30% by heat) injected after the primary combustion region. Experiments with Coal:CB mixtures as reburn fuels were performed using the 30 kW burner facility. Part I deals with results from experiments using pure FB and Coal:FB blends as reburn fuels while Part II presents results on extent of NOx reduction using pure DB and Coal:DB blends as reburn fuels (RF). In the current work, results on NOx emission are presented with FB and Coal:FB blends as RF. The parametric studies include: equivalence ratio in reburn zone (ERRBZ), vitiated air, angle of reburn nozzles, presence and absence of heat exchangers (HEXs), and baseline NOx concentration. The optimum operating conditions for FB reburning were found to be conditions with vitiation at ERRBZ = 1.1 with 45° upward counter-current injection in the presence of HEXs. NOx emissions were reduced by as much as 96%.

09 BIOMASS FUELS↗

Alkaline solution/binder ratio as a determining factor in the alkaline activation of aluminosilicates

This study investigates the effect of the alkaline solution/binder (S/B) ratio on the composition and nanostructure of the reaction products generated in the alkaline activation of aluminosilicates. The experiments used two mixtures of fly ash and dehydroxylated white clay and for each of these, varying proportions of the solution components. The alkali activator was an 8 M NaOH solution (with and without sodium silicate) used at three S/B ratios: 0.50, 0.75 and 1.25. The {sup 29}Si, {sup 27}Al MAS NMR and XRD characterisation of the reaction products reveal that for ratios nearest the value delivering suitable paste workability, the reaction-product composition and structure depend primarily on the nature and composition of the starting materials and the alkaline activator used. However, when an excess alkaline activator is present in the system, the reaction products tend to exhibit SiO{sub 2}/Al{sub 2}O{sub 3} ratios of approximately 1, irrespective of the composition of the starting binder or the alkaline activator.

36 MATERIALS SCIENCE↗

Adsorption kinetics, thermodynamics, and isotherm studies for functionalized lanthanide-chelating resins

Conventional ion exchange resins are widely utilized to remove metals from aqueous solutions, but their limited selectivity precludes dilute ion extraction. This research investigated the adsorption performance of ligand-functionalized resins towards rare earth elements (REE). Functionalized resin particles were synthesized by grafting different ligands (diethylenetriaminepentaacetic dianhydride (DTPADA), phosphonoacetic acid (PAA), or N,N-bis(phosphonomethyl)glycine (BPG)) onto pre-aminated polymeric adsorbents (diameter-0.6 mm). Lanthanide uptake trends were evaluated for the functionalized resins using batch adsorption experiments with a mixture of three REEs (Nd, Gd, and Ho at 0.1–1000 mg/L each). Resin physical-chemical properties were determined by measuring their surface area, ligand concentrations, and acidity constants. The aminated supports contained 4.0 mmol/g primary amines, and ligand densities for the functionalized resins were 0.33 mmol/g (PAA), 0.22 mmol/g (BPG), and 0.42 mmol/g (DTPADA). Kinetic studies revealed that the functionalized resins followed pseudo-second order binding kinetics with rates limited by intraparticle diffusion. Capacity estimates for total REE adsorption based on Langmuir q Max were 0.12 mg/g (amine; ≈ 0.77 µmol/g), 5.0 mg/g (PAA; ≈ 32.16 µmol/g), 3.0 mg/g (BPG; ≈ 19.30 µmol/g), and 2.9 mg/g (DTPADA; ≈ 18.65 µmol/g). Lastly, attaching ligands to the aminated resins greatly improved their REE binding strength and adsorption efficiency.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Development of a Structure for Lossless Ion Manipulations (SLIM) High Charge Capacity Array of Traps

Enhancing the sensitivity of low abundance ions in a complex mixture without sacrificing experiment throughput is highly desirable. This work demonstrates a way to greatly improve the sensitivity of ion mobility (IM) selected ions by accumulating them in an array of high-capacity ion traps located inside a novel structures for lossless ion manipulations ion mobility spectrometer (SLIM-IMS) module. The array of ion traps used in this work consisted of seven independently controllable traps. Each trap was 386 mm long and possessed a charge capacity of ~4.5×10 8 charges, with a linear range extending to ~2.5×10 8 charges. Each ion trap could be used to extract a peak (or ions over a mobility range) from an ion mobility separation based on arrival time. Ions could be stored without losses for long times (>100 s) and then released all at once or one trap at a time. It was possible to accumulate large ion populations by extracting and storing ions over repeated IM separations. We report enrichment of up to seven individual ion distributions could be performed using the seven independently controllable ion traps. Additionally, the ion trapping process effectively compressed ion populations into narrow peaks, which provides a greatly improved basis for subsequent ion manipulations. The array of high charge-capacity ion traps provides a flexible addition to SLIM and a powerful tool for IMS-MS applications requiring high sensitivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrical and thermal conductivities in dense plasmas

Expressions for the electrical and thermal conductivities in dense plasmas are derived combining the Chester-Thellung-Kubo-Greenwood approach and the Kramers approximation. The infrared divergence is removed assuming a Drude-like behaviour. An analytical expression is obtained for the Lorenz number that interpolates between the cold solid-state and the hot plasma phases. An expression for the electrical resistivity is proposed using the Ziman-Evans formula, from which the thermal conductivity can be deduced using the analytical expression for the Lorenz number. The present method can be used to estimate electrical and thermal conductivities of mixtures. Comparisons with experiment and quantum molecular dynamics simulations are done.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Hydrogen plasma dynamics in the spherical theta pinch plasma target for heavy ion stripping

Due to the superior ability of dense and highly ionised plasmas to ionise penetrating heavy ion beams to degrees beyond those reachable by common gas strippers, many experiments have been performed to find suitable plasma generators for this application. In the field of gas discharges, mainly z-pinch devices have been investigated so far, which are known to be limited by the nonlinear focusing effects of the plasma columns sustaining current and by electrode erosion. The spherical theta pinch has therefore been proposed as a substitution for the z-pinch, promising progress by inductive rather than capacitive coupling and displacement of the outer magnetic field by the dense, diamagnetic discharge plasma. As yet mainly experiments with argon/hydrogen mixture gas have been performed, which is not suitable for the application as a plasma stripper, this paper describes the first detailed analysis of the plasma parameters and dynamics of a hydrogen plasma created by the spherical theta pinch. These include the time integrated and time resolved electron density, the dynamics of the plasma in the discharge vessel, the comparison with the argon dominated plasma, and an outlook to reachable characteristics with similar devices.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

A versatile dual-species Zeeman slower for caesium and ytterbium

We describe the design, construction, and operation of a versatile dual-species Zeeman slower for both Cs and Yb, which is easily adaptable for use with other alkali metals and alkaline earths. With the aid of analytic models and numerical simulation of decelerator action, we highlight several real-world problems affecting the performance of a slower and discuss effective solutions. To capture Yb into a magneto-optical trap (MOT), we use the broad {sup 1}S{sub 0} to {sup 1}P{sub 1} transition at 399 nm for the slower and the narrow {sup 1}S{sub 0} to {sup 3}P{sub 1} intercombination line at 556 nm for the MOT. The Cs MOT and slower both use the D2 line (6{sup 2}S{sub 1/2} to 6{sup 2}P{sub 3/2}) at 852 nm. The slower can be switched between loading Yb or Cs in under 0.1 s. We demonstrate that within a few seconds the Zeeman slower loads more than 10{sup 9} Yb atoms and 10{sup 8} Cs atoms into their respective MOTs. These are ideal starting numbers for further experiments on ultracold mixtures and molecules.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗

Catalytic Depolymerization and Upgrading of Lignin for Vanillin Production: Cooperative Research and Development Final Report, CRADA Number CRD-14-545

Examine catalytic conversion of lignin using multifunctional catalysts that are able to depolymerize and oxidize lignin to a vanillin-rich stream. Examine separation processes for isolation of vanillin from product mixtures. Conduct preliminary experiments to determine if deconstructed lignin streams can be metabolized by Pseudomonas putida.

09 BIOMASS FUELS↗