Search NASA⌕ Search

SEARCH · Search NASA

Results for “NOISE SPECTRUM”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1995

Effects of correlated noise on the full-spectrum combining and complex-symbol combining arraying techniques

The process of combining telemetry signals received at multiple antennas, commonly referred to as arraying, can be used to improve communication link performance in the Deep Space Network (DSN). By coherently adding telemetry from multiple receiving sites, arraying produces an enhancement in signal-to-noise ratio (SNR) over that achievable with any single antenna in the array. A number of different techniques for arraying have been proposed and their performances analyzed in past literature. These analyses have compared different arraying schemes under the assumption that the signals contain additive white Gaussian noise (AWGN) and that the noise observed at distinct antennas is independent. In situations where an unwanted background body is visible to multiple antennas in the array, however, the assumption of independent noises is no longer applicable. A planet with significant radiation emissions in the frequency band of interest can be one such source of correlated noise. For example, during much of Galileo's tour of Jupiter, the planet will contribute significantly to the total system noise at various ground stations. This article analyzes the effects of correlated noise on two arraying schemes currently being considered for DSN applications: full-spectrum combining (FSC) and complex-symbol combining (CSC). A framework is presented for characterizing the correlated noise based on physical parameters, and the impact of the noise correlation on the array performance is assessed for each scheme.

Vazirani, P.↗
NASA NTRS1978

Use of a priori statistics to minimize acquisition time for RFI immune spread spectrum systems

The optimum acquisition sweep strategy was determined for a PN code despreader when the a priori probability density function was not uniform. A psuedo noise spread spectrum system was considered which could be utilized in the DSN to combat radio frequency interference. In a sample case, when the a priori probability density function was Gaussian, the acquisition time was reduced by about 41% compared to a uniform sweep approach.

Holmes, J. K.↗
NASA NTRS1945

Method of expanding noise autocorrelation function in a power series

Under certain conditions the normalized autocorrelation function ρ(τ) of stationary random noise may be expanded as a power series about the point τ = 0. This paper indicates that the coefficients of the expansion are rather simply related to the average rate of occurrence of zeros in the noise function and its derivatives. The expansion of academic interest in providing another perspective of the relationships among the noise function, its power spectrum, and its autocorrelation function. It may also be of practical interest in providing a quick means of estimating the normalized autocorrelation function from a noise record over the range of τ in which the power series converges rapidly. The class of noise spectrum for which convergent series expansion is not possible is of interest in pointing up necessary physical characteristics of noise signals which have such spectra.

F W Lehan↗
NASA NTRS2007

GIFTS SM EDU Level 1B Algorithms

The Geosynchronous Imaging Fourier Transform Spectrometer (GIFTS) SensorModule (SM) Engineering Demonstration Unit (EDU) is a high resolution spectral imager designed to measure infrared (IR) radiances using a Fourier transform spectrometer (FTS). The GIFTS instrument employs three focal plane arrays (FPAs), which gather measurements across the long-wave IR (LWIR), short/mid-wave IR (SMWIR), and visible spectral bands. The raw interferogram measurements are radiometrically and spectrally calibrated to produce radiance spectra, which are further processed to obtain atmospheric profiles via retrieval algorithms. This paper describes the GIFTS SM EDU Level 1B algorithms involved in the calibration. The GIFTS Level 1B calibration procedures can be subdivided into four blocks. In the first block, the measured raw interferograms are first corrected for the detector nonlinearity distortion, followed by the complex filtering and decimation procedure. In the second block, a phase correction algorithm is applied to the filtered and decimated complex interferograms. The resulting imaginary part of the spectrum contains only the noise component of the uncorrected spectrum. Additional random noise reduction can be accomplished by applying a spectral smoothing routine to the phase-corrected spectrum. The phase correction and spectral smoothing operations are performed on a set of interferogram scans for both ambient and hot blackbody references. To continue with the calibration, we compute the spectral responsivity based on the previous results, from which, the calibrated ambient blackbody (ABB), hot blackbody (HBB), and scene spectra can be obtained. We now can estimate the noise equivalent spectral radiance (NESR) from the calibrated ABB and HBB spectra. The correction schemes that compensate for the fore-optics offsets and off-axis effects are also implemented. In the third block, we developed an efficient method of generating pixel performance assessments. In addition, a random pixel selection scheme is designed based on the pixel performance evaluation. Finally, in the fourth block, the single pixel algorithms are applied to the entire FPA.

Tian, Jialin↗
NASA NTRS1981

A spectroscopic, photometric, and magnetic study of the starspot on II Pegasi

A description is presented of extensive observations of II Peg during 1977 and 1978, taking into account multicolor broad-band photometry, high-dispersion spectroscopy, low-dispersion spectrophotometry, and Zeeman analysis. During this time the star showed periodic light variations in excess of a 0.4 mag range attributable to the presence of a large starspot or an equivalent nonuniform surface brightness distribution. The high-precision multicolor photometry, which differed greatly from previous photometric results, illustrates that the starspots on II Peg are continually evolving on time scales of approximately 1 year or less. A low-dispersion spectrum of the large spot showed pronounced VO and TiO molecular adsorption features. A high-resolution, high signal-to-noise Reticon spectrum at lambda 6707 does not show any compelling evidence of previously reported lithium in this star.

Vogt, S. S.↗
NASA NTRS1974

Direct measurement of sound sources in air jets using the crossed beam correlation technique

Properties of density fluctuations were measured in the turbulent regions of a 2.54 cm air jet, at M = 0.7, 1.0 and 1.94. After calibration tests, it was found that the absorption of infrared radiation at 4.3 microns by the naturally present quantities of carbon-dioxide in air was directly proportional to the air density if a sufficiently wide bandpass (0.08 microns) was used. Moreover, regions of the band could be selected that adequately discriminated against temperature variations. The cross-correlation of two such beams intersecting in the jet gave a measure of the local properties at the intersection point. A derivation is presented relating the local density correlation function to the self and shear generated noise in the far field of the jet. The measured correlations are used to predict the axial distribution of source strengths and the spectrum of noise due to a unit volume of turbulence.

Damkevala, R. J.↗
NASA NTRS1974

Preliminary study of gear noise characteristics

Experimental results and conclusions are presented about the noise characteristics of gears as a function of their operating conditions. The interpretive possibilities offered by real time noise and vibration spectrum analysis are emphasized. The noise reducing effects of light weight insulation boxes are also discussed.

Gafitanu, M. D.↗
NASA NTRS1996

X-Ray Spectrum of a Narrow Line Quasi-Stellar Object

This AO-3 observation of a new narrow-line QSO was motivated by our extensive study of the unclassified X-ray sources from the ROSAT/IRAS survey of Boller et al. IRAS 2018.1-2244 was observed to have Balmer lines and forbidden lines of roughly equal width. There are possibly weak broad wings on the H-alpha line. One of the questions to be addressed by hard X-ray spectroscopy is whether or not these wings are to be interpreted as scattered or weakly transmitted flux from a hidden broad-line region. The optical spectrum of this QSO also has very weak permitted Fe II lines, possibly indicative of a hidden broad line region. A new wrinkle on the concept of the narrow-line QSO is the gradual realization that luminous objects with very strong but narrow Fe II lines are showing up preferentially in soft X-ray surveys. The AO-1 objective was to detect the Geminga Pulsar and to interpret its 2-10 keV spectrum and pulse profile in terms of its X-ray emission spectra. Also, the AO-1 observed the Seyfert galaxy NGC 3516 to obtain a high signal-to-noise ratio spectrum. We expected NGC 3516 to be one of the best candidates for a successful demonstration of the details of the warm-absorber model.

Halpern, Jules P.↗
NASA NTRS2007

GIFTS SM EDU Data Processing and Algorithms

The Geosynchronous Imaging Fourier Transform Spectrometer (GIFTS) Sensor Module (SM) Engineering Demonstration Unit (EDU) is a high resolution spectral imager designed to measure infrared (IR) radiances using a Fourier transform spectrometer (FTS). The GIFTS instrument employs three Focal Plane Arrays (FPAs), which gather measurements across the long-wave IR (LWIR), short/mid-wave IR (SMWIR), and visible spectral bands. The raw interferogram measurements are radiometrically and spectrally calibrated to produce radiance spectra, which are further processed to obtain atmospheric profiles via retrieval algorithms. This paper describes the processing algorithms involved in the calibration stage. The calibration procedures can be subdivided into three stages. In the pre-calibration stage, a phase correction algorithm is applied to the decimated and filtered complex interferogram. The resulting imaginary part of the spectrum contains only the noise component of the uncorrected spectrum. Additional random noise reduction can be accomplished by applying a spectral smoothing routine to the phase-corrected blackbody reference spectra. In the radiometric calibration stage, we first compute the spectral responsivity based on the previous results, from which, the calibrated ambient blackbody (ABB), hot blackbody (HBB), and scene spectra can be obtained. During the post-processing stage, we estimate the noise equivalent spectral radiance (NESR) from the calibrated ABB and HBB spectra. We then implement a correction scheme that compensates for the effect of fore-optics offsets. Finally, for off-axis pixels, the FPA off-axis effects correction is performed. To estimate the performance of the entire FPA, we developed an efficient method of generating pixel performance assessments. In addition, a random pixel selection scheme is designed based on the pixel performance evaluation.

Tian, Jialin↗
NASA NTRS1978

Whistler mode noise in Jupiter's inner magnetosphere

A study is made of the amplitude and spectral extent of whistler mode noise in the inner magnetosphere of Jupiter. It is found that the 'hat-shaped' pitch angle distributions of energetic electrons (21 and 31 MeV at L=3) are consistent with those predicted in the presence of a band-limited spectrum of whistler mode noise. The equatorial maximum linear growth rate of parallel propagating whistlers are consistent with those necessary to limit the energetic electron intensities by the whistler mode instability. It is noted that the wave phase speeds before wave reflection can occur at high latitudes and that wave growth is limited to a disk-like region centered around the magnetic equator. The frequency extent of the whistler mode noise spectrum may be estimated by the range of frequencies maximally unstable to equatorial linear growth. A value is found for the spectral density of the broadband whistler mode noise necessary to balance radial diffusion of energetic electrons above the critical range, and an expression is derived for the energetic electron system response to fluctuations about the limiting flux value.

Sentman, D. D.↗
NASA NTRS2010

l/f Noise in the Superconducting Transition of a MgB2 Thin Film

The noise voltage spectral density in the superconducting transition of a MgB2 thin film on a SiN-coated Si thick substrate was measured over the frequency range 1 Hz-to-1 KHz. Using established bolometer noise theory the theoretical noise components due to Johnson, 1/f(excess) and phonon noise are modeled to the measured data. It is shown that for the case of a MgB2 thin film in the vicinity of the mid-point of transition, coupled to a heat sink via a fairly high thermal conductance (approximately equal to 10(sup -1) W/K)) that the measured noise voltage spectrum is 1/f limited and exhibits lit dependence with a varying between 0.3 and 0.5 in the measured frequency range. At a video frame rate frequency of 30 Hz the measured noise voltage density in the film is approximately equal to 61 nV /the square root of HZ, using this value an upper limit of electrical NEP approximately equal to 0.67pW / the square root of Hz is implied for a practical MgB2 bolometer operating at 36.1 K.

Lakew, B.↗
NASA NTRS1981

Prediction of jet exhaust noise on airframe surfaces during flight

The behavior of pressure fluctuations measured on the airframe of a prototype high lift jet transport (YC-14) is presented. The data are characterized in terms of a particular jet exhaust flow field idealization, jet mixing noise, and exhaust shock noise. Generalized spectrum shapes and scaling relations for peak level and frequency of peak level are developed, and the frequency is found to depend on jet exhaust velocity and aircraft velocity. Comparisons are made with near-field engine exhaust noise of a conventional jet, and results suggest that the same two exhaust noises are important for both aircraft types. Surface fluctuating pressure data are assessed, and results suggest that the jet mixing and exhaust shock noise source characterizations for the YC-14 have useful applicability to conventionally configured jets.

Butzel, L. M.↗
NASA NTRS2012

Frequency Correction for MIRO Chirp Transformation Spectroscopy Spectrum

This software processes the flyby spectra of the Chirp Transform Spectrometer (CTS) of the Microwave Instrument for Rosetta Orbiter (MIRO). The tool corrects the effect of Doppler shift and local-oscillator (LO) frequency shift during the flyby mode of MIRO operations. The frequency correction for CTS flyby spectra is performed and is integrated with multiple spectra into a high signal-to-noise averaged spectrum at the rest-frame RF frequency. This innovation also generates the 8 molecular line spectra by dividing continuous 4,096-channel CTS spectra. The 8 line spectra can then be readily used for scientific investigations. A spectral line that is at its rest frequency in the frame of the Earth or an asteroid will be observed with a time-varying Doppler shift as seen by MIRO. The frequency shift is toward the higher RF frequencies on approach, and toward lower RF frequencies on departure. The magnitude of the shift depends on the flyby velocity. The result of time-varying Doppler shift is that of an observed spectral line will be seen to move from channel to channel in the CTS spectrometer. The direction (higher or lower frequency) in the spectrometer depends on the spectral line frequency under consideration. In order to analyze the flyby spectra, two steps are required. First, individual spectra must be corrected for the Doppler shift so that individual spectra can be superimposed at the same rest frequency for integration purposes. Second, a correction needs to be applied to the CTS spectra to account for the LO frequency shifts that are applied to asteroid mode.

Lee, Seungwon↗
NASA NTRS2018

Isochronal Age-mass Discrepancy of Young Stars: SCExAO/CHARIS Integral Field Spectroscopy of the HIP 79124 Triple System

We present SCExAO/CHARIS 1.1-2.4 μm integral field direct spectroscopy of the young HIP 79124 triple system. HIP 79124 is a member of the Scorpius-Centaurus association, consisting of an A0V primary with two low-mass companions at a projected separation of < 1″. Thanks to the high quality wavefront corrections provided by SCExAO, both companions are decisively detected without the employment of any PSF-subtraction algorithm to eliminate quasi-static noise. The spectrum of the outer C object is very well matched by Upper Scorpius M4 ± 0.5 standard spectra, with a T(eff) = 2945 ± 100 K and a mass of ∼350 M(Jup). HIP 79124 B is detected at a separation of only 180 mas in a highly-correlated noise regime, and it falls in the spectral range M6 ± 0.5 with T(eff) = 2840 ± 190 K and ∼100 M(Jup). Previous studies of stellar populations in Sco-Cen have highlighted a discrepancy in isochronal ages between the lower-mass and higher-mass populations. This could be explained either by an age spread in the region, or by conventional isochronal models failing to reproduce the evolution of low-mass stars. The HIP 79124 system should be coeval, and therefore it provides an ideal laboratory to test these scenarios. We place the three components in a color-magnitude diagram and find that the models predict a younger age for the two low-mass companions (∼3 Myr) than for the primary star (∼6 Myr). These results imply that the omission of magnetic effects in conventional isochronal models inhibit them from reproducing early low-mass stellar evolution, which is further supported by the fact that new models that include such effects provide more consistent ages in the HIP 79124 system.

Ruben Asensio-Torres↗
NASA NTRS2006

Real Time Phase Noise Meter Based on a Digital Signal Processor

A digital signal-processing meter for phase noise measurement on sinusoidal signals is dealt with. It enlists a special hardware architecture, made up of a core digital signal processor connected to a data acquisition board, and takes advantage of a quadrature demodulation-based measurement scheme, already proposed by the authors. Thanks to an efficient measurement process and an optimized implementation of its fundamental stages, the proposed meter succeeds in exploiting all hardware resources in such an effective way as to gain high performance and real-time operation. For input frequencies up to some hundreds of kilohertz, the meter is capable both of updating phase noise power spectrum while seamlessly capturing the analyzed signal into its memory, and granting as good frequency resolution as few units of hertz.

phase noise↗
NASA NTRS1984

Uniform apparent contrast noise: A picture of the noise of the visual contrast detection system

A picture which is a sample of random contrast noise is generated. The noise amplitude spectrum in each region of the picture is inversely proportional to spatial frequency contrast sensitivity for that region, assuming the observer fixates the center of the picture and is the appropriate distance from it. In this case, the picture appears to have approximately the same contrast everywhere. To the extent that contrast detection thresholds are determined by visual system noise, this picture can be regarded as a picture of the noise of that system. There is evidence that, at different eccentricities, contrast sensitivity functions differ only by a magnification factor. The picture was generated by filtering a sample of white noise with a filter whose frequency response is inversely proportional to foveal contrast sensitivity. It was then stretched by a space-varying magnification function. The picture summmarizes a noise linear model of detection and discrimination of contrast signals by referring the model noise to the input picture domain.

Ahumada, A. J., Jr.↗
NASA NTRS1993

Some aspects of the aeroacoustics of high-speed jets

Some of the background to contemporary jet aeroacoustics is addressed. Then scaling laws for noise generation by low-Mach-number airflows and by turbulence convected at 'not so low' Mach number is reviewed. These laws take into account the influence of Doppler effects associated with the convection of aeroacoustic sources. Next, a uniformly valid Doppler-effect approximation exhibits the transition, with increasing Mach number of convection, from compact-source radiation at low Mach numbers to a statistical assemblage of conical shock waves radiated by eddies convected at supersonic speed. In jets, for example, supersonic eddy convection is typically found for jet exit speeds exceeding twice the atmospheric speed of sound. The Lecture continues by describing a new dynamical theory of the nonlinear propagation of such statistically random assemblages of conical shock waves. It is shown, both by a general theoretical analysis and by an illustrative computational study, how their propagation is dominated by a characteristic 'bunching' process. That process associated with a tendency for shock waves that have already formed unions with other shock waves to acquire an increased proneness to form further unions - acts so as to enhance the high-frequency part of the spectrum of noise emission from jets at these high exit speeds.

Lighthill, James↗
NASA NTRS1956

On the Contribution of Turbulent Boundary Layers to the Noise Inside a Fuselage

The following report deals in preliminary fashion with the transmission through a fuselage of random noise generated on the fuselage skin by a turbulent boundary layer. The concept of attenuation is abandoned and instead the problem is formulated as a sequence of two linear couplings: the turbulent boundary layer fluctuations excite the fuselage skin in lateral vibrations and the skin vibrations induce sound inside the fuselage. The techniques used are those required to determine the response of linear systems to random forcing functions of several variables. A certain degree of idealization has been resorted to. Thus the boundary layer is assumed locally homogeneous, the fuselage skin is assumed flat, unlined and free from axial loads and the 'cabin' air is bounded only by the vibrating plate so that only outgoing waves are considered. Some of the details of the statistical description have been simplified in order to reveal the basic features of the problem. The results, strictly applicable only to the limiting case of thin boundary layers, show that the sound pressure intensity is proportional to the square of the free stream density, the square of cabin air density and inversely proportional to the first power of the damping constant and to the second power of the plate density. The dependence on free stream velocity and boundary layer thickness cannot be given in general without a detailed knowledge of the characteristics of the pressure fluctuations in the boundary layer (in particular the frequency spectrum). For a flat spectrum the noise intensity depends on the fifth power of the velocity and the first power of the boundary layer thickness. This suggests that boundary layer removal is probably not an economical means for decreasing cabin noise. In general, the analysis presented here only reduces the determination of cabin noise intensity to the measurement of the effect of any one of our variables (free stream velocity, boundary layer thickness, plate thickness or the characteristic velocity of propagation in the plate). The plate generates noise by vibrating in resonance over a wide range of frequencies and increasing the damping constant is consequently an effective method of decreasing noise generation. One of the main features of the results is that the relevant quantities upon which noise intensity depends are non-dimensional numbers in which boundary layer and plate properties enter as ratios. This is taken as an indication that in testing models of structures for boundary layer noise it is not sufficient to duplicate in the model the structural characteristics of the fuselage. One must match properly the characteristics of the exicitng pressure fluctuations to that of the structure.

Corcos, G. M.↗