Search NASA⌕ Search

SEARCH · Search NASA

Results for “NOSE CONE”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D Karlgaard↗
NASA NTRSDate not supplied

Trajectory Reconstruction of the Low-Earth Orbit Flight Test of an Inflatable Decelerator

The Low-Earth Orbit Flight Test of an Inflatable Decelerator (LOFTID) project conducted a flight test of a 6m inflatable aeroshell. The LOFTID test article was a secondary payload on an Atlas V launcher that carried the Joint Polar Satellite System-2 (JPSS-2) as its primary payload. The vehicle launched on November 10th, 2022. After reaching orbit, the LOFTID test article inflated the aeroshell, separated from the upper stage on an entry trajectory, and entered the atmosphere to splash down in the Pacific Ocean under parachutes. The test concept of operations is shown in Figure 1. The test article was instrumented with a variety of sensors to be used for post-flight evaluation of vehicle performance. Data from one of the key sensors for trajectory reconstruction, the Inertial Measurement Unit (IMU), was not captured in the data recorder due to a malfunction. Data from the nose cone mounted Flush Air Data Sensing (FADS) system were successfully acquired. The layout of the FADS sensors and the measured pressures during atmospheric entry are shown in Figure 2. The FADS data were combined with a Newtonian flow pressure model [1, 2] to produce estimates of the atmospheric relative trajectory. A Mach number anchoring technique given in [2] was used to stabilize estimates in high speed flight conditions. Since no IMU data were available, a trajectory simulation was used to provide the Mach number time history. The resulting estimates of the atmospheric-relative trajectory are shown in Figures 3. Given the loss of the IMU data, alternate methods for trajectory reconstruction are being explored. One approach under investigation is the use of the on-board video recorder data to be analyzed to reconstruct attitude motion. This approach is currently under investigation and will be reported on in the final paper. The Newtonian flow pressure model for the FADS analysis will also be updated with a CFD-based pressure model.

Christopher D. Karlgaard↗
NASA NTRS2007

Effects of Nose Bluntness on Stability of Hypersonic Boundary Layers over Blunt Cone

Receptivity and stability of hypersonic boundary layers are numerically investigated for boundary layer flows over a 5-degree straight cone at a free-stream Mach number of 6.0. To compute the shock and the interaction of shock with the instability waves, we solve the Navier-Stokes equations in axisymmetric coordinates. The governing equations are solved using the 5th-order accurate weighted essentially non-oscillatory (WENO) scheme for space discretization and using third-order total-variation-diminishing (TVD) Runge-Kutta scheme for time integration. After the mean flow field is computed, disturbances are introduced at the upstream end of the computational domain. Generation of instability waves from leading edge region and receptivity of boundary layer to slow acoustic waves are investigated. Computations are performed for a cone with nose radii of 0.001, 0.05 and 0.10 inches that give Reynolds numbers based on the nose radii ranging from 650 to 130,000. The linear stability results showed that the bluntness has a strong stabilizing effect on the stability of axisymmetric boundary layers. The transition Reynolds number for a cone with the nose Reynolds number of 65,000 is increased by a factor of 1.82 compared to that for a sharp cone. The receptivity coefficient for a sharp cone is about 4.23 and it is very small, approx.10(exp -3), for large bluntness.

Kara, K.↗
NASA NTRS2020

Toward Transition Modeling in a Hypersonic Boundary Layer at Flight Conditions

An accurate physics-based transition prediction method integrated with computational fluid dynamics (CFD) solvers is pursued for hypersonic boundary layer flows over slender hypersonic vehicles at flight conditions. The geometry and flow conditions are selected to match relevant trajectory locations from the ascent phase of the HIFiRE-1 flight experiment, namely, a 7-degree half-angle cone with 2.5 mm nose radius, freestream Mach numbers in the range of 3.8 – 5.5 and freestream unit Reynolds numbers in the range of 3.3 × 10(exp 6) – 21.4 × 10(exp 6) m(exp -1). Earlier research had shown that the onset of transition during the HIFiRE-1 flight experiment correlated with an amplification factor of N ≈ 13.5 for the planar Mack modes. However, to incorporate the N-factor correlations into a CFD code, we investigate surrogate models for disturbance amplification that avoid the direct computation of stability characteristics. A commonly used approach for low-speed flows is based on an a priori database of stability characteristics for locally similar profiles. However, the results presented in this paper demonstrate that the application of this approach to hypersonic boundary layers over blunt spherical nose-tip cones leads to large, unacceptable errors in the predictions of amplification factors, mainly due to its failure in accounting for the effects of the entropy layer on the boundary-layer profiles along the length of the model. We propose and demonstrate an alternate approach that employs the stability computations for a canonical set of blunt cone configurations to train a physics-informed convolutional neural network model that is shown to provide substantially improved transition predictions for hypersonic flow configurations with entropy-layer effects. Furthermore, the excellent performance of the neural network model is also confirmed for cone configurations with nose radius and half-angle values that do not correspond to those used to build the database. Finally, the convolutional neural network model is shown to outperform the linear stability calculations for underresolved basic states.

Pedro Paredes↗
NASA NTRS2013

Geometric Effects on the Amplification of First Mode Instability Waves

The effects of geometric changes on the amplification of first mode instability waves in an external supersonic boundary layer were investigated using numerical techniques. Boundary layer stability was analyzed at Mach 6 conditions similar to freestream conditions obtained in quiet ground test facilities so that results obtained in this study may be applied to future test article design to measure first mode instability waves. The DAKOTA optimization software package was used to optimize an axisymmetric geometry to maximize the amplification of the waves at first mode frequencies as computed by the 2D STABL hypersonic boundary layer stability analysis tool. First, geometric parameters such as nose radius, cone half angle, vehicle length, and surface curvature were examined separately to determine the individual effects on the first mode amplification. Finally, all geometric parameters were allowed to vary to produce a shape optimized to maximize the amplification of first mode instability waves while minimizing the amplification of second mode instability waves. Since first mode waves are known to be most unstable in the form of oblique wave, the geometries were optimized using a broad range of wave frequencies as well as a wide range of oblique wave angles to determine the geometry that most amplifies the first mode waves. Since first mode waves are seen most often in flows with low Mach numbers at the edge of the boundary layer, the edge Mach number for each geometry was recorded to determine any relationship between edge Mach number and the stability of first mode waves. Results indicate that an axisymmetric cone with a sharp nose and a slight flare at the aft end under the Mach 6 freestream conditions used here will lower the Mach number at the edge of the boundary layer to less than 4, and the corresponding stability analysis showed maximum first mode N factors of 3.

Kirk, Lindsay C.↗
NASA NTRS1962

Tables of Aerodynamic Coefficients Obtained from Developed Newtonian Expressions for Complete and Partial Conic and Spheric Bodies at Combined Angles of Attack and Sideslip with Some Comparisons with Hypersonic Experimental Data

Closed-form expressions and tables composed from these expressions are presented for complete and partial conic and spheric bodies at combined angles of attack and sideslip in Newtonian flow. Aerodynamic coefficients of these bodies are tabulated for various body segments over a range of angles of attack from 1 deg to 85 deg and angles of sideslip from 0 deg to 15 deg. Some comparisons between Newtonian predictions and hypersonic experimental aerodynamic characteristics were made for conic bodies hawing various surface slopes, nose bluntnesses, and body cross sections to indicate the range of validity of the theory. In general, the theory is shown to agree quite well with experimental results for sharp-nose complete cones and for configurations hawing large blunted noses and steep surface slopes. However, agreement between theory and experiment generally is poor for the more slender, slightly blunted complete or half conic bodies and also for sharp-nose half conic bodies where real-flow phenomena such as forebody interference, viscous forces, leeward surface contributions, or leading-edge pressure reductions may have significant effect. The agreement between theory and experiment for the bodies considered can be improved by using the stagnation pressure coefficient behind a normal shock rather than 2 as the Newtonian coefficient, although for the sharp-nose half conic bodies there i s no theoretical justification for this modification.

Armstrong, William O.↗
NASA NTRS1958

Effects of Nose Angle and Mach Number on Transition on Cones at Supersonic Speeds

An investigation has been made to determine the transition characteristics of a group of smooth, sharp-nosed cones varying from 10 degrees to sixty degrees in included apex angle over a Mach number range from 1.61 to 2.20 and a range of Reynolds number per foot from about 1.5 x 10 to the 6th power to 8 x 10 to the 6th power. Increasing the cone angle is shown to decrease slightly the transition Reynolds number, whereas the effects of changes of Mach number and unit Reynolds number are negligible. When transition occurred within 15 to 20 percent of the model length from the base there was a dropoff in transition Reynolds number. (author)

Czarnecki, K R↗
NASA NTRS1991

A parametric study of dissociation and ionization models at 12 km/sec

Thermochemical nonequilibrium-solution dependence on available models for the chemical reaction rates is examined. Solutions from the Kang and Dunn (1973) reaction-rate set, the Park rate set of 1987, and the Park rate set of 1991 are compared. The blunt-nosed, axisymmetric geometry considered is a 60-deg sphere cone with nose radius of 1.07 m and cicular aft skirt. The nonequilibrium test case is 12 km/sec entry into the earth's atmosphere at 80 km altitude. The model variations are implemented into the Langley aerothermodynamics upwind relaxation algorithm code. While variations in the reaction rates have no effect on the surface pressure distribution and little effect on the convective heating, the effect on degree of ionization and radiative heating can be a factor of three.

Mitcheltree, R. A.↗
NASA NTRS1958

Heat-Transfer Measurements in Free Flight at Mach Numbers up to 14.6 on a Flat-Faced Conical Nose with a Total Angle of 29 Degrees

Skin-temperature measurements have been made at several locations on a flat-faced cone-cylinder nose which was flight tested on a fivestage rocket-propeller model to a Mach number of 14.64 and a free-stream Reynolds number of 2.0 x 10(exp 6), based on flat-face diameter, at an altitude of 66,300 feet. The copper nose had a 29 deg total-angle conical section which was 1.6 flat-face diameters long. The aerodynamic-heating rates determined from the temperature measurements reached 1,440 Btu/( sec) (sq ft) on the flat face. The heating rates near the center of the flat face agreed well at Mach numbers up to 13.6 with those obtained by a theory for laminar stagnation-point heating in equilibrium dissociated air (Avco Res. Rep. 1). At Mach numbers above 13.6, the heating rates at locations near the center of the flat face became progressively lower than stagnation-point theory and. were 29 percent lower at Mach number 14.6 at the end. of the test. The reason for this behavior of the heating on the central part of the flat face was not determined. Excluding the relatively low heating rates that occurred on the central part of the nose at the highest Mach numbers, the distribution of experimental heating along the innermost 0.79 of the flat-face radius, expressed as a percentage of stagnation-point heating, was in fair agreement with the distribution predicted by laminar theory. At a location of 0.71 radii from the stagnation point, the experimental heating was very near 130 percent of the theoretical stagnation-point rate at Mach numbers from 11 to 14.5. The experimental beating rates on the conical section of the nose were in good agreement with laminar-cone theory using the assumption of theoretical sharp-cone static pressure on the conical section.

Rumsey, Charles B↗
NASA NTRS1961

Effect of Nose Bluntness on Transition for a Cone and a Hollow Cylinder at Mach Numbers 1.41 and 2.01

An investigation has been made to determine the effects of nose bluntness on boundary-layer transition for a cone with an included angle of 10 degrees and for a hollow cylinder. The tests were conducted at Mach numbers of 1.41 and 2.01 for free-stream Reynolds numbers per foot ranging from 1 x 10(exp 6) to 9 x 10(exp 6). The investigation was made with the use of schlieren photography for which the models were aligned with the free stream. For the 10 degree cone, the favorable effects of nose blunting were so small at both test Mach numbers as to be lost within the experimental accuracy. For small amounts of nose blunting on the hollow cylinder, for which the ratio of bluntness height to transition distance for the sharp-leading-edge cylinder was relatively small, there was little, if any, effect of blunting on transition. For somewhat larger values of this ratio, nose blunting had a favorable effect on transition. The magnitude of the favorable effect was dependent upon the size and the shape of the bluntness, and the maximum increase in transition distance relative to the sharp-leading-edge cylinder is in good agreement with the theoretical predictions of NACA Technical Report 1312. For relatively large values of the ratio of nose bluntness to transition distance, the effects of nose blunting were adverse for both the cone and the cylinder. In general, adverse effects due to blunting were larger for the flat bluntness than for the hemispherical or the round bluntness of equal bluntness height. Increasing the Mach number increased the size of bluntness required to induce adverse effects at constant free-stream Reynolds number per foot, delayed the adverse effects to higher values of Reynolds number per foot for constant nose bluntness, and reduced the abruptness of the transition decrease.

Monta, William J.↗
NASA NTRS1961

Effects of Cone Angle, Mach Number, and Nose Blunting on Transition at Supersonic Speeds

An investigation has been made to determine the transition characteristics of a group of blunt cones which varied in included apex angle from 27 deg to 60 deg over a Mach number range from 1.61 to 2.20 and a range of tunnel Reynolds number per foot from about 1.5 x 10(exp 6) to 8.0 x 10(exp 6). The tests were made at zero angle of attack and with zero heat transfer. The results indicate that the general level of transition Reynolds number based on boundary-layer momentum thickness and local flow conditions just outside the boundary layer varied between 600 and 1,100. Changes in Mach number had little effect on transition distance and transition Reynolds number for the near-sharp or very small bluntnesses. The effect of Mach number variation on the larger hemispherical bluntnesses was much stronger, with the strongest Mach number effect occurring for Mach numbers between 1.61 and 1.82. With an increase in nose radius, there was a strong decrease in transition distance and transition Reynolds number at the lower Mach numbers. This adverse effect tended to become weaker with increase in Mach number. An increase in cone angle at a constant Mach number caused a reduction in transition distance and transition Reynolds number for the blunt configurations which had approximately the same values of nose radius.

Czarnecki, K. R.↗