Search NASA⌕ Search

SEARCH · Search NASA

Results for “NOTCH STRENGTH”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1974

Deformation characteristics and time-dependent notch sensitivity of Udimet 700 at intermediate temperatures

Time dependent notch sensitivity was observed in Udimet 700 sheet, bar, and investment castings between 1000 and 1400 F (538 -760 C), but not at 1600 F (871 C). As was the case for modified Waspaloy, Waspaloy and Inconel 718, it occurred in notched specimens loaded below the yield strength when the creep deformation was localized. For each alloy and notched specimen geometry, a stress-average particle size zone can be defined that characterizes the notch sensitive behavior.

Wilson, D. J.↗
NASA NTRS2005

Solid Oxide Fuel Cell Seal Glass - BN Nanotubes Composites

Solid oxide fuel cell seal glass G18 composites reinforced with approx.4 weight percent of BN nanotubes were fabricated via hot pressing. Room temperature strength and fracture toughness of the composite were determined by four-point flexure and single edge V-notch beam methods, respectively. The strength and fracture toughness of the composite were higher by as much as 90% and 35%, respectively, than those of the glass G18. Microscopic examination of the composite fracture surfaces using SEM and TEM showed pullout of the BN nanotubes, similar in feature to fiber-reinforced ceramic matrix composites with weak interfaces. Other mechanical and physical properties of the composite will also be presented.

Bansal, Narottam P.↗
NASA NTRS1980

Notch sensitivity of space shuttle tile materials

Tests were conducted at room temperature to determine the notch sensitivity of the thermal protection tile for the space shuttle. Two types of RSI tile were studied: LI-900 and LI-2200. Three point bend specimens were cut from discarded tiles in the in-plane (ip) and through-the-thickness (ttt) directions. They were tested with or without a sharp notch. The LI-900 (ip and ttt) specimens were not very notch sensitive, but the LI-2200 (ip and ttt) specimens were. The LI-2200 material showed about a 35 percent reduction in strength due to the presence of the notch. This reduction in strength should be considered in the design of mechanically fastened tile concepts.

Newman, J. C., Jr.↗
DOE OSTI2024

Investigation of the notch sensitivity of tailorable long fiber discontinuous prepreg composite laminates

Tailorable discontinuous fiber composite laminates provide relative formability beyond that of continuous fiber laminates, while achieving improved mechanical performance over comparable stochastic systems. Here, in this work, the notch sensitivity of engineered prepreg platelet molded composite (PPMC) laminates is investigated using the open-hole tension (OHT) test and compared to available data for stochastic PPMCs and continuous fiber laminates made with the same material. The press-formed thermoplastic composites (AS4/PEKK) were molded with a quasi-isotropic stacking sequence. The discontinuous PPMC laminate was found to be notch insensitive with OHT strengths ranging from 145.4 MPa (CV $=$ 7%) for d/w $=$ 0.5 to 229.3 MPa (CV $=$ 9%) for d/w $=$ 0.25. The highly ordered meso-structure of the engineered PPMC laminate yields comparatively excellent mechanical properties for relatively thin laminates in contrast to stochastic systems. Both net- and gross-section failures were observed for d/w $=$ 0.25, which suggests that the engineered PPMC laminates studied here maintain a degree of inherent, internal stress concentrations that compete with those caused by geometric features such as a circular hole. Computational simulations of the OHT tests with explicitly represented platelets were found to be in good agreement with experimental measurements. The progressive failure analysis was used to conduct a numerical investigation of the stacking sequence and platelet meso-morphology.

36 MATERIALS SCIENCE↗
NASA NTRS1975

Effect of service usage on tensile, fatigue, and fracture properties of 7075-T6 and 7178-T6 aluminum alloys

A study has been made to determine the effects of extensive service usage on some basic material properties of 7075-T6 and 7178-T6 aluminum alloy materials. The effects of service usage were determined by comparing material properties for new material (generally obtained from the literature) with those for material cut from the center wing box of a C-130B transport airplane with 6385 flight-hours of service. The properties investigated were notched and unnotched fatigue strengths, fatigue-crack-growth rate, fracture toughness, and tensile properties. For the properties investigated and the parameter ranges considered (crack length, stress ratio, etc.), the results obtained showed no significant difference between service and new materials.

Everett, R. A., Jr.↗
NASA NTRS1978

The effect of microstructure on hydrogen embrittlement of the nickel-base superalloy, Udimet 700

Material from a single heat of cast and wrought Udimet 700 was processed and/or heat treated to produce five material conditions with identical chemical compositions but with distinct microstructural variations, and then evaluated for susceptibility to hydrogen embrittlement. Two prealloyed powder conditions exhibited significantly improved resistance to hydrogen embrittlement, as compared to wrought material. No degradation in notch or smooth tensile strengths occurred, and average ductilities of 25 percent reduction of area were determined for 2 hydrogen evaluation procedures. For the most severe hydrogenation procedure, ductility levels were reduced to 15 percent. These improvements were attributed to cleaner grain boundaries and decreases grain size.

Gray, H. R.↗
NASA NTRS1978

The effect of microstructure on hydrogen embrittlement of the nickel base superalloy, Udimet 700

Material from a single heat of cast and wrought Udimet 700 was processed and/or heat treated to produce five material conditions with identical chemical compositions but with distinct microstructural variations, and then evaluated for susceptibility to hydrogen embrittlement. Two prealloyed powder conditions exhibited significantly improved resistance to hydrogen embrittlement, as compared to wrought material. No degradation in notch or smooth tensile strengths occurred, and average ductilities of 25 percent reduction of area were determined for 2 hydrogen evaluation procedures. For the most severe hydrogenation procedure, ductility levels were reduced to 15 percent. These improvements were attributed to cleaner grain boundaries and decreased grain size.

Gray, H. R.↗
NASA NTRS1985

The fracture behavior of filament wound cylinders with surface flaws

The behavior of tensile coupons with surface notches of various semielliptical shapes has been evaluated for specimens obtained from a thick filament wound graphite/epoxy cylinder. Specimens with very shallow notches were observed to be notch insensitive and the unnotched strength from these specimens was determined to be 54.97 Ksi with an associated failure strain of 1.328 percent. Specimens with deeper notches were sensitive to notch depth and notch aspect ratio. Isotropic linear elastic fracture mechanics with an estimated fracture toughness of 27.2 Ksi-in.-to the 1/2 correctly predicted the influence of notch depth, aspect ratio and specimen finite width.

Harris, C. E.↗
NASA NTRS1983

Experimental and analytical investigation of the fracture processes of boron/aluminum laminates containing notches

Experimental results for five laminate orientations of boron/aluminum composites containing either circular holes or crack-like slits are presented. Specimen stress-strain behavior, stress at first fiber failure, and ultimate strength were determined. Radiographs were used to monitor the fracture process. The specimens were analyzed with a three-dimensional elastic-elastic finite-element model. The first fiber failures in notched specimens with laminate orientation occurred at or very near the specimen ultimate strength. For notched unidirectional specimens, the first fiber failure occurred at approximately one-half of the specimen ultimate strength. Acoustic emission events correlated with fiber breaks in unidirectional composites, but did not for other laminates. Circular holes and crack-like slits of the same characteristic length were found to produce approximately the same strength reduction. The predicted stress-strain responses and stress at first fiber failure compared very well with test data for laminates containing 0 deg fibers.

Johnson, W. S.↗
NASA NTRS1938

The Influence of Notches Under Static Stress

From the described experiments it is seen that notches are a potential source of strength decrease even under static stress, which the designer must take into consideration. Section I is a general treatment of notch influence under the various types of stresses. Section II treats the influence of notches in thin sheet as is used in airplane construction.

Matthaes, K↗
NASA NTRS1975

Deformation characteristics and time-dependent notch sensitivity of Udimet 700 at intermediate temperatures

Time-dependent notch sensitivity of Udimet 700 sheet, bar, and investment castings was observed between 1000 and 1400 F (538-760 C) but not at 1600 F (871 C). As was the case for Modified Waspaloy, Waspaloy, Rene 41, Inconel 718, and TD-NiCr, it occurred when notched specimens were loaded below the yield strength and when creep deformation was localized. For each gamma-prime strengthened alloy and notched specimen geometry, a stress-average particle size zone can be defined to characterize the notch-sensitive behavior.

Wilson, D. J.↗