Search NASA⌕ Search

SEARCH · Search NASA

Results for “Natural Fractures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The role of annealing and grain boundary controls on the mechanical properties of limestones and marbles

Chemical and mechanical processes are coupled in many geological and geochemical environments. Reactive processes anneal defects and restructure grain boundaries, modifying their elastic properties, levels of internal friction, wave propagation rates and fracture behaviors. The nature of these changes is, however, contingent on the initial state of the rock. Here, in this study, impulse excitation was used to measure changes in mechanical properties as a function of dry and steam heating time at 300 °C for three carbonate rocks: Carrara marble, Carthage marble (Burlington Limestone), and Texas Cream limestone (Edwards limestone), with initial porosities of about 1 %, 3 %, and 27 %, respectively. Frequency-dependent phenomena along with mineral recrystallization were observed. This was coupled with small-angle X-ray and neutron scattering analysis to determine the relationship between changes in bulk mechanical and microstructural properties. An observed decrease in both the Young's and shear moduli in the experimental limestones as a function of heating time reflects and quantifies a reduction in the stiffness of the rock due to annealing. The internal friction of the samples first increases then decreases with reaction time, reflecting defect annealing, but this was balanced against grain boundary dissolution apparently driven by condensation of steam in the confined grain-boundary environment. This suggests an increase in the boiling point under confinement leading to dissolution, increased porosity and widening of the grain boundaries. In addition, comparison of small-angle X-ray and neutron scattering results suggests that it is inappropriate to assume that pores are empty for quantitative analysis of typical small-angle scattering samples.

58 GEOSCIENCES↗
DOE OSTI2024

Integrating the Design of Desalination Technologies into Produced Water Network Optimization

The oil and gas energy sector uses billions of gallons of water for hydraulic fracturing each year to extract oil and gas. The water injected into the ground for fracturing along with naturally occurring formation water from oil wells surfaces back in the form of produced water. Produced water can contain high concentrations of total dissolved solids and is unfit for reuse outside the oil and gas industry without desalination. In semi-arid shale plays, produced water desalination for beneficial reuse could play a crucial role in alleviating water shortages and addressing extreme drought conditions. In this poster we co-optimize the design and operation of desalination technologies along with operational decisions across produced water networks. A multi-period produced water network model with simplified split-fraction-based desalination nodes is developed. Rigorous steady-state desalination mathematical models based on mechanical vapor recompression are developed and embedded at the desalination sites in the network model. An optimal common design across all periods is ensured using global capacity constraints. The solution approach is demonstrated for multi-period planning problems on networks from the PARETO open-source library. Model formulation and challenges associated with scalability are discussed.

Naik, Sakshi↗
DOE OSTI2024

Integrating the Design of Desalination Technologies into Produced Water Network Optimization

The oil and gas energy sector uses billions of gallons of water for hydraulic fracturing each year to extract oil and gas. The water injected into the ground for fracturing along with naturally occur-ring formation water from the oil wells surfaces back in the form of produced water. Produced water can contain high concentrations of total dissolved solids and is unfit for reuse outside the oil and gas industry without desalination. In semi-arid shale plays, produced water desalination for beneficial reuse could play a crucial role in alleviating water shortages and addressing extreme drought conditions. In this paper we co-optimize the design and operation of desalination technologies along with operational decisions across produced water networks. A multi-period produced water network model with simplified split-fraction-based desalination nodes is developed. Rigorous steady-state desalination mathematical models based on mechanical vapor recompression are developed and embedded at the desalination sites in the network model. An optimal common design is ensured across all periods using global capacity constraints. The solution approach is demonstrated for multi-period planning problems on networks from the PARETO open-source library. Model formulation and challenges associated with scalability are discussed.

Naik, Sakshi↗
NASA NTRS1988

Reliability based analysis of contact problems

The Batdorf model is modified to include the reduction in shear due to the effect of compressive stresses on the crack face. This new formulation was used to obtain the probability of failure of ceramic components under contact stress conditions. The combined effect of the surface and volume flaws are included in the analysis. Due to the nature of the fracture of brittle materials under compressive loading, the component is modeled as a series system in order to establish bounds on the probability of failure.

Powers, Lynn M.↗
DOE OSTI2022

From Fluid Flow to Coupled Processes in Fractured Rock: Recent Advances and New Frontiers

Abstract Quantitative predictions of natural and induced phenomena in fractured rock is one of the great challenges in the Earth and Energy Sciences with far‐reaching economic and environmental impacts. Fractures occupy a very small volume of a subsurface formation but often dominate fluid flow, solute transport and mechanical deformation behavior. They play a central role in CO 2 sequestration, nuclear waste disposal, hydrogen storage, geothermal energy production, nuclear nonproliferation, and hydrocarbon extraction. These applications require predictions of fracture‐dependent quantities of interest such as CO 2 leakage rate, hydrocarbon production, radionuclide plume migration, and seismicity; to be useful, these predictions must account for uncertainty inherent in subsurface systems. Here, we review recent advances in fractured rock research covering field‐ and laboratory‐scale experimentation, numerical simulations, and uncertainty quantification. We discuss how these have greatly improved the fundamental understanding of fractures and one's ability to predict flow and transport in fractured systems. Dedicated field sites provide quantitative measurements of fracture flow that can be used to identify dominant coupled processes and to validate models. Laboratory‐scale experiments fill critical knowledge gaps by providing direct observations and measurements of fracture geometry and flow under controlled conditions that cannot be obtained in the field. Physics‐based simulation of flow and transport provide a bridge in understanding between controlled simple laboratory experiments and the massively complex field‐scale fracture systems. Finally, we review the use of machine learning‐based emulators to rapidly investigate different fracture property scenarios and accelerate physics‐based models by orders of magnitude to enable uncertainty quantification and near real‐time analysis.

58 GEOSCIENCES↗
DOE OSTI2022

Fractal Characterization of Multimodal, Multiscale Images of Shale Rock Fracture Networks

An array of multimodal and multiscale images of fractured shale rock samples and analogs was collected with the aim of improving the numerical representation of fracture networks. 2D and 3D reconstructions of fractures and matrices span from 10 –6 to 100 m. The origin of the fracture networks ranged from natural to thermal maturation to hydraulically induced maturation. Images were segmented to improve fracture identification. Then, the fractal dimension and length distribution of the fracture networks were calculated for each image dataset. The resulting network connectivity and scaling associations are discussed at length on the basis of scale, sample and order of magnitude. Fracture network origin plays an important role in the resulting fracture systems and their scaling. Rock analogs are also evaluated using these descriptive tools and are found to be faithful depictions of maturation-induced fracture networks.

58 GEOSCIENCES↗
NASA NTRS1977

Friction, deformation and fracture of single-crystal silicon carbide

An investigation was conducted to determine the nature of the deformation and fracture of silicon carbide and its effects on friction properties. Friction experiments were conducted with hemispherical and conical diamond riders sliding on the basal plane of silicon carbide. The results indicate that, when deformation is primarily elastic, the friction does not depend on crystallographic orientation and there is no detectable fracture or cracking. When, however, plastic deformation occurs, silicon carbide exhibits anisotropic friction and deformation behavior. Surface fracture crack patterns surrounding wear tracks are observed to be of three types. The crack-geometries of two types are generally independent of orientation, the third crack, however, depends on the orientation. All surface cracks extend into subsurface.

Miyoshi, K.↗
DOE OSTI2023

Fracture Intensity Impacts on Reaction Front Propagation and Mineral Weathering in Three‐Dimensional Fractured Media

Abstract Studying reaction front propagation in heterogeneous natural settings is challenging, but numerical simulations can provide insight into the varying spatial and temporal scales of reaction front propagation. Here, the impact of increasing fracture intensity on mineral dissolution rates, and the extent of reaction front propagation is investigated using reactive transport simulations in upscaled discrete fracture network domains with varied fracture intensity. Domain‐averaged dissolution rates vary less than 0.5 log units regardless of the fracture intensity, but the spatial distribution of reactions is controlled by the location and number of dead‐end fractures and the number of connected flowpaths through the domain. Higher fracture intensities lead to more weathering in the domain because of more available mineral for water‐rock interactions. We find that reaction fronts propagate through the primary flowpaths in the first 10,000 years of the simulation for a 10‐m length domain, then propagate into secondary flowpaths and dead‐end fractures between 10,000 and 100,000 years, and finally into the matrix over timescales of hundreds of thousands of years. The domain‐averaged reaction rates decrease through time corresponding to a transition from dissolution in advection‐dominated, fast‐flowing pathways, to dissolution in transport‐limited zones of disconnected fractures and matrix. Matrix dissolution, or dissolution under transport‐limited conditions, is the dominant process at late times in these simulations. The results of these simulations recreate the observed paradox found in nature where highly fractured hillslopes tend to be more weathered but have slower weathering rates, while hillslopes with fewer fractures, are less weathered but have higher dissolution rates.

58 GEOSCIENCES↗
DOE OSTI2020

Two-Phase Fluid Flow Properties of Rough Fractures With Heterogeneous Wettability: Analysis With Lattice Boltzmann Simulations

Fractures are conduits for fluid flow in low-permeability geological formations. Multiphase flow properties of fractures are important in natural processes and in engineering applications such as the evaluation of the sealing capacity of caprocks and productivity of hydrocarbon-bearing tight rocks. Investigations of flow and transport through fractures typically focus on the effects of fracture geometric and mechanical factors such as aperture, roughness, and compressibility. The wettability of the fracture surfaces and its influence on microscale interfacial phenomena and macroscale effective transport properties are seldom studied. In this study, we investigated the effect of heterogeneous wetting properties on the displacement of water by supercritical CO2 through a series of lattice Boltzmann method simulations. The results show the evolution of the CO2 plume within a fracture is controlled by both the roughness of the aperture field and the wetting distribution. We combined these factors into a capillary pressure map that can be related to the macroscopic flow behavior of the fracture. We observed that heterogeneous wetting distributions promote the residual trapping of water where lower capillary pressures allowed for isolated water pockets in higher capillary pressure zones. Analysis of fracture unsteady relative permeability shows the effect of wetting on permeability evolution and provides support for the viscous-coupling relative permeability model. Finally, analysis of the steady-state relative permeability and saturation demonstrates a strong correlation between permeability and the standard deviation of the capillary pressure field. Thus, characterizing the distribution of wetting properties of fractures is crucial to understanding multiphase fracture flow and transport properties.

58 GEOSCIENCES↗
NASA NTRS1976

Fundamental analysis of the failure of polymer-based fiber reinforced composites

A mathematical model is described which will permit predictions of the strength of fiber reinforced composites containing known flaws to be made from the basic properties of their constituents. The approach was to embed a local heterogeneous region (LHR) surrounding the crack tip into an anisotropic elastic continuum. The model should (1) permit an explicit analysis of the micromechanical processes involved in the fracture process, and (2) remain simple enough to be useful in practical computations. Computations for arbitrary flaw size and orientation under arbitrary applied load combinations were performed from unidirectional composites with linear elastic-brittle constituent behavior. The mechanical properties were nominally those of graphite epoxy. With the rupture properties arbitrarily varied to test the capability of the model to reflect real fracture modes in fiber composites, it was shown that fiber breakage, matrix crazing, crack bridging, matrix-fiber debonding, and axial splitting can all occur during a period of (gradually) increasing load prior to catastrophic fracture. The computations reveal qualitatively the sequential nature of the stable crack process that precedes fracture.

Kanninen, M. F.↗
DOE OSTI2021

Machine-learning predictions of the shale wells’ performance

The ultra-low permeability nature of shale reservoirs leads to an extended linear flow and necessitates horizontal wells with multi-stage engineered fractures to efficiently extract hydrocarbons resources. These artificially-generated and naturally-occurring fractures form complex networks that create complex flow regimes which control oil production. These fractures are neither identical nor equally-spaced, which leads to a production profile with a masked onset of the boundary-dominated flow. The combination of the extended linear flow with the indeterminate onset of the boundary-dominated flow challenges the current deterministic analytic approaches to forecast the estimated ultimate recovery (EUR). In this work, we propose a novel machine-learning approach which overcomes these challenges and provides reliable EUR estimates based on field-wide analyses. We implement a novel unsupervised machine learning (ML) methodology, which allows for automatic identification of the optimal number of features (signals) present in the data based on non-negative matrix/tensor factorization coupled with k-means clustering incorporating regularization and physics constraints. In the presented analyses, the input data to the ML algorithm is the available (public) production history from the field collected at existing unconventional reservoirs. We validate our approach through hindcasting of the production data, where we achieved an excellent agreement. In addition, our approach is able to identify the poorly-performing wells, which could benefit from early refracing. Our approach provides fast and accurate estimations of the well performance without presumptions about the state of the well or the flow regime.

03 NATURAL GAS↗
DOE OSTI2021

A comprehensive review of proppant embedment in shale reservoirs: Experimentation, modeling and future prospects

This paper provides a comprehensive review on the application of proppants to maintain fracture permeability over the lifetime of a well based on published observations from experiments and modeling. The review identifies and describes important processes occurring during proppant embedment, during hydraulic fracturing, laboratory testing of fracture conductivity, proppant embedment and modeling of proppant embedment. Lastly, this paper identifies the challenges and knowledge gaps that also provide future avenues of research and opportunities for collaborative technological development which requires an interdisciplinary approach of science, engineering in academia, government, and private sector.

03 NATURAL GAS↗
NASA NTRS1979

An analysis of interface crack in adhesively bonded lap shear joints

This paper presents an analytical study of interface crack problems in adhesively bonded lap shear joints. A convenient and accurate method of analysis is developed on the basis of conservation laws in elasticity and of the fundamental relationships in fracture mechanics of interface crack problems. The problem is eventually reduced to a system of linear algebraic equations of mixed-mode stress intensity factor solutions. One of the salient features of the present approach is that the interface crack-tip stress intensity solutions can be determined accurately and directly by the information extracted from the far field. Solutions of the interface crack problems in lap shear joints have been obtained for the cases of various adhesive/adherend material systems and geometric configurations of the crack and the joint. Of particular interest is the evaluation of the mixed-mode stress intensity factors and the associated energy release rates. They are determined explicitly to illustrate the fundamental nature of the joint fracture problem.

Wang, S. S.↗
NASA NTRS1997

Design Protocols and Analytical Strategies that Incorporate Structural Reliability Models

Ceramic matrix composites (CMC) and intermetallic materials (e.g., single crystal nickel aluminide) are high performance materials that exhibit attractive mechanical, thermal, and chemical properties. These materials are critically important in advancing certain performance aspects of gas turbine engines. From an aerospace engineers perspective the new generation of ceramic composites and intermetallics offers a significant potential for raising the thrust/weight ratio and reducing NO(sub x) emissions of gas turbine engines. These aspects have increased interest in utilizing these materials in the hot sections of turbine engines. However, as these materials evolve and their performance characteristics improve a persistent need exists for state-of-the-art analytical methods that predict the response of components fabricated from CMC and intermetallic material systems. This need provided the motivation for the technology developed under this research effort. Continuous ceramic fiber composites exhibit an increase in work of fracture, which allows for 'graceful' rather than catastrophic failure. When loaded in the fiber direction these composites retain substantial strength capacity beyond the initiation of transverse matrix cracking despite the fact that neither of its constituents would exhibit such behavior if tested alone. As additional load is applied beyond first matrix cracking, the matrix tends to break in a series of cracks bridged by the ceramic fibers. Any additional load is born increasingly by the fibers until the ultimate strength of the composite is reached. Thus modeling efforts supported under this research effort have focused on predicting this sort of behavior. For single crystal intermetallics the issues that motivated the technology development involved questions relating to material behavior and component design. Thus the research effort supported by this grant had to determine the statistical nature and source of fracture in a high strength, NiAl single crystal turbine blade material; map a simplistic future strength envelope of the material; develop a statistically based reliability computer algorithm; verify the reliability model and computer algorithm-, and model stator vanes for rig tests. Thus establishing design protocols that enable the engineer to analyze and predict the mechanical behavior of ceramic composites and intermetallics would mitigate the prototype (trial and error) approach currently used by the engineering community. The primary objective of the research effort supported by this short term grant is the continued creation of enabling technologies for the macro-analysis of components fabricated from ceramic composites and intermetallic material systems. The creation of enabling technologies aids in shortening the product development cycle of components fabricated from the new high technology materials.

Duffy, Stephen F.↗
NASA NTRS1997

Design Protocols and Analytical Strategies that Incorporate Structural Reliability Models

Ceramic matrix composites (CMC) and intermetallic materials (e.g., single crystal nickel aluminide) are high performance materials that exhibit attractive mechanical, thermal and chemical properties. These materials are critically important in advancing certain performance aspects of gas turbine engines. From an aerospace engineer's perspective the new generation of ceramic composites and intermetallics offers a significant potential for raising the thrust/weight ratio and reducing NO(x) emissions of gas turbine engines. These aspects have increased interest in utilizing these materials in the hot sections of turbine engines. However, as these materials evolve and their performance characteristics improve a persistent need exists for state-of-the-art analytical methods that predict the response of components fabricated from CMC and intermetallic material systems. This need provided the motivation for the technology developed under this research effort. Continuous ceramic fiber composites exhibit an increase in work of fracture, which allows for "graceful" rather than catastrophic failure. When loaded in the fiber direction, these composites retain substantial strength capacity beyond the initiation of transverse matrix cracking despite the fact that neither of its constituents would exhibit such behavior if tested alone. As additional load is applied beyond first matrix cracking, the matrix tends to break in a series of cracks bridged by the ceramic fibers. Any additional load is born increasingly by the fibers until the ultimate strength of the composite is reached. Thus modeling efforts supported under this research effort have focused on predicting this sort of behavior. For single crystal intermetallics the issues that motivated the technology development involved questions relating to material behavior and component design. Thus the research effort supported by this grant had to determine the statistical nature and source of fracture in a high strength, NiAl single crystal turbine blade material; map a simplistic failure strength envelope of the material; develop a statistically based reliability computer algorithm, verify the reliability model and computer algorithm, and model stator vanes for rig tests. Thus establishing design protocols that enable the engineer to analyze and predict the mechanical behavior of ceramic composites and intermetallics would mitigate the prototype (trial and error) approach currently used by the engineering community. The primary objective of the research effort supported by this short term grant is the continued creation of enabling technologies for the macroanalysis of components fabricated from ceramic composites and intermetallic material systems. The creation of enabling technologies aids in shortening the product development cycle of components fabricated from the new high technology materials.

Duffy, Stephen F.↗
DOE OSTI2020

Towards real-time forecasting of natural gas production by harnessing graph theory for stochastic discrete fracture networks

In this work, we compare hydrocarbon production curves obtained from a graph-based reduced-order model with the high-fidelity Discrete Fracture Network (DFN) predictions for a fracture network created using data from a real shale site. We observe that the bounds for the high fidelity DFN model lie within the bounds for the reduced order model, implying that the reduced-order model provides a conservative estimate. Moreover, we found that except for first-passage times and late arriving mass, the production curves from the reduced-order model predict transport accurately. However, it is to be noted that the results are inspite of trading a three-dimensional geometry for a reduced system in the form of a graph, one that is 500–1000 times faster in terms of computational efficiency (for this particular application). In addition, we also compare the production curves for large drawdown and small drawdown using our graph approach. The reduced-order model is successful in showing that the long term productivity is higher in case of small drawdown although the initial productivity is higher for large drawdown. Thus, this reduced-order model offers great potential in uncertainty quantification for production, as well as in providing operators with information to make real-time decisions for optimal production.

03 NATURAL GAS↗
DOE OSTI2021

Phase-field modeling of rate-dependent fluid-driven fracture initiation and propagation

The rate-dependent behavior associated with deformation and fracturing of materials, such as natural rocks, poses significant challenges for modeling. In addition to the complications of the viscoelastic response, the speed of fracture propagation reflects micromechanical mechanisms in the fracture process zone(FPZ). In order to represent these complicated behaviors, a thermodynamically consistent, rate-dependent fracture model is required. Based on rigorous thermodynamic principles, we derive a rate-dependent phase-field mechanical model coupled with single-phase fluid flow in both the matrix and the fracture. The model is guaranteed to satisfy energy conservation during fracture propagation. Here, the system of equations is solved using the introduced solution procedure and a novel preconditioner that accounts for the complex fluid-structure interaction. The proposed phase-field model is tested against several benchmark problems on solid-fluid coupling, fluid-driven fracture propagation and rate-dependent viscoelastic deformation. The model serves as a strong basis for investigating rate-dependent fracturing experiments and for making predictions of material behaviors under new conditions.

42 ENGINEERING↗