Search NASA⌕ Search

SEARCH · Search NASA

Results for “Noise control”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS2006

Flow and Noise Control in High Speed and High Reynolds Number Jets Using Plasma Actuators

The idea of manipulating flow to change its characteristics is over a century old. Manipulating instabilities of a jet to increase its mixing and to reduce its radiated noise started in the 1970s. While the effort has been successful in low-speed and low Reynolds number jets, available actuators capabilities in terms of their amplitude, bandwidth, and phasing have fallen short in control of high-speed and high Reynolds number jets of practical interest. Localized arc filament plasma actuators have recently been developed and extensively used at Gas Dynamics and Turbulence Laboratory (GDTL) for control of highspeed and high Reynolds number jets. While the technique has been quite successful and is very promising, all the work up to this point had been carried out using small high subsonic and low supersonic jets from a 2.54 cm diameter nozzle exit with a Reynolds number of about a million. The preliminary work reported in this paper is a first attempt to evaluate the scalability of the technique. The power supply/plasma generator was designed and built in-house at GDTL to operate 8 actuators simultaneously over a large frequency range (0 to 200 kHz) with independent control over phase and duty cycle of each actuator. This allowed forcing the small jet at GDTL with azimuthal modes m = 0, 1, 2, 3, plus or minus 1, plus or minus 2, and plus or minus 4 over a large range of frequencies. This power supply was taken to and used, with minor modifications, at the NASA Nozzle Acoustic Test Rig (NATR). At NATR, 32 actuators were distributed around the 7.5 in. nozzle (a linear increase with nozzle exit diameter would require 60 actuators). With this arrangement only 8 actuators could operate simultaneously, thus limiting the forcing of the jet at NATR to only three azimuthal modes m = plus or minus 1, 4, and 8. Very preliminary results at NATR indicate that the trends observed in the larger NASA facility in terms of the effects of actuation frequency and azimuthal modes are similar in both small GDTL and larger NASA jets. However, the actuation authority seems to fall short in the larger jet at higher Mach numbers, resulting in decreased amplitude response compared to the small jet, which is attributed at this point to the lack of sufficient number of actuators. The preliminary results seem also to suggest that amplitude of actuation tones is similar in both the small and larger jets.

Samimy, M.↗
NASA NTRS2014

Analysis of Dual Rotating Rake Data from the NASA Glenn Advanced Noise Control Fan Duct with Artificial Sources

The Rotating Rake mode measurement system was designed to measure acoustic duct modes generated by a fan stage. Initially, the mode amplitudes and phases were quantified from a single rake measurement at one axial location. To directly measure the modes propagating in both directions within a duct, a second rake was mounted to the rotating system with an offset in both the axial and the azimuthal directions. The rotating rake data analysis technique was then extended to include the data measured by the second rake. The analysis resulted in a set of circumferential mode levels at each of the two rake microphone locations. Radial basis functions were then least-squares fit to this data to obtain the radial mode amplitudes for the modes propagating in both directions within the duct. Validation experiments have been conducted using artificial acoustic sources. Results are shown for the measurement of the standing waves in the duct from sound generated by one and two acoustic sources that are separated into the component modes propagating in both directions within the duct. Measured reflection coefficients from the open end of the duct are compared to analytical predictions.

Noise↗
NASA NTRS1992

A Lightweight Loudspeaker for Aircraft Communications and Active Noise Control

A series of new, lightweight loudspeakers for use on commercial aircraft has been developed. The loudspeakers use NdFeB magnets and aluminum alloy frames to reduce the weight. The NdFeB magnet is virtually encapsulated by steel in the new speaker designs. Active noise reduction using internal loudspeakers was demonstrated to be effective in 1983. A weight, space, and cost efficient method for creating the active sound attenuating fields is to use the existing cabin loudspeakers for both communication and sound attenuation. This will require some additional loudspeaker design considerations.

Warnaka, Glenn E.↗
NASA NTRS1981

Laboratory study of efficient add-on treatments for interior noise control in light aircraft

Experimental and theoretical studies of the transmission loss (TL) of 1.15 x 1.46 m flat stiffened-skin aluminum panels are described. Panel configurations included panels with no treatment and eight combinations of treatments consisting of a fiberglass-septum layer, a foam-foil damping material, and a plywood double wall trim panel. Measured TL of the untreated panel and the panel with a damping layer showed characteristics of the double mass law: at low frequencies the TL followed a mass law trend associated with the average mass of both skin and stiffness, while at higher frequencies the TL followed a mass law trend associated with skin mass only. A comparison of TL for panels treated with a damping layer, a fiberglass layer, or a trim panel showed that the effects of damping are frequency dependent with some performing better below 500 Hz and others performing better above 500 Hz. Treatment combinations showed that two treatments with the same mass could have TL values different by about 10 dB, while other combinations having weights different by a factor of two could have TL values within a few dB over most of the frequency range. The highest TL values (50 dB at 1000 Hz) were obtained with a treatment consisting of a fiberglass layer, a trim panel, and damping layers on both the stiffened panel and the trim panel.

Mixson, J. S.↗
NASA NTRS1986

Development of rotorcraft interior noise control concepts. Phase 2: Full scale testing, revision 1

The phase 2 effort consisted of a series of ground and flight test measurements to obtain data for validation of the Statistical Energy Analysis (SEA) model. Included in the gound tests were various transfer function measurements between vibratory and acoustic subsystems, vibration and acoustic decay rate measurements, and coherent source measurements. The bulk of these, the vibration transfer functions, were used for SEA model validation, while the others provided information for characterization of damping and reverberation time of the subsystems. The flight test program included measurements of cabin and cockpit sound pressure level, frame and panel vibration level, and vibration levels at the main transmission attachment locations. Comparisons between measured and predicted subsystem excitation levels from both ground and flight testing were evaluated. The ground test data show good correlation with predictions of vibration levels throughout the cabin overhead for all excitations. The flight test results also indicate excellent correlation of inflight sound pressure measurements to sound pressure levels predicted by the SEA model, where the average aircraft speech interference level is predicted within 0.2 dB.

Yoerkie, C. A.↗
NASA NTRS1987

Experimental evaluation of active noise control in a thin cylindrical shell

The effect of frequency on the performance of an active control system is examined. The effects are related to the mechanisms of the structural-acoustic coupling and the nature of the control field acoustics. The cylinder used in the experiment consists of a thin aluminum shell terminated with two end plates in a cylindrical configuration. The experiment was conducted at 324, 450, and 475 Hz, corresponding to shell nondimensional frequencies of Omega = 0.15, 0.21, and 0.22. It is found that the nature of the primary field is determined by the coupling between the shell and the acoustic space as well as the frequency of excitation.

Abler, Steven B.↗
NASA NTRS1988

Mechanisms of noise control inside a finite cylinder

Preliminary results are presented for a simple elastic cylinder/acoustic cavity model. The validity of the mode matching method, which was used to couple the shell vibrations to the interior acoustic response, has been validated by comparison with Junger's (1985) method. In addition, the importance of both structural and acoustic damping in the medium response was shown to be dramatic.

Lester, H. C.↗
NASA NTRS1996

Aerodynamic Requirements for BVI Noise Control

As a rotor blade moves through the air, it sheds vortices. These vortices shed along the length of the blade over time form the wake. The strongest vortices of the wake are those trailing from the tip of the blade. When a rotating blade system moves under certain operating conditions, each blade will impinge on the tip vortices shed by itself or other blades. This impingement is called a blade-vortex interaction, or BVI. Although the blade and trailing tip vortices interact with many different orientations, one of the two extremes, either parallel or perpendicular interaction, is usually modelled. In a perpendicular interaction, the portion of the blade that is actually interacting with the travelling vortex at any given time is very small. A parallel interaction, however, has the largest concurrent interaction with the blade, as a result this case is given the most attention. One of the most commonly studied occurrences of blade-vortex interactions is associated with low-speed descending rotorcraft flight. BVI occur when the tip vortices shed by the blades intersect the plane of the rotor. BVI cause local pressure changes over the blades which are responsible, in part, for the acoustic signature of the rotorcraft. The local pressure changes also cause vibrations which lead to fatigue of both the blades and the mechanical components driving the blades.

Wells, Valana L.↗
NASA NTRS1997

Broadband Noise Control Using Predictive Techniques

Predictive controllers have found applications in a wide range of industrial processes. Two types of such controllers are generalized predictive control and deadbeat control. Recently, deadbeat control has been augmented to include an extended horizon. This modification, named deadbeat predictive control, retains the advantage of guaranteed stability and offers a novel way of control weighting. This paper presents an application of both predictive control techniques to vibration suppression of plate modes. Several system identification routines are presented. Both algorithms are outlined and shown to be useful in the suppression of plate vibrations. Experimental results are given and the algorithms are shown to be applicable to non- minimal phase systems.

Eure, Kenneth W.↗
NASA NTRS2008

An Autonomous Sensor System Architecture for Active Flow and Noise Control Feedback

Multi-channel sensor fusion represents a powerful technique to simply and efficiently extract information from complex phenomena. While the technique has traditionally been used for military target tracking and situational awareness, a study has been successfully completed that demonstrates that sensor fusion can be applied equally well to aerodynamic applications. A prototype autonomous hardware processor was successfully designed and used to detect in real-time the two-dimensional flow reattachment location generated by a simple separated-flow wind tunnel model. The success of this demonstration illustrates the feasibility of using autonomous sensor processing architectures to enhance flow control feedback signal generation.

Humphreys, William M, Jr.↗