Search NASA⌕ Search

SEARCH · Search NASA

Results for “Nuclear fuel performance”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A Metallic Fuel Performance Benchmark Problem Based on the IFR-1 Experiment

Metallic nuclear fuels are an active area of research and development for use in advanced reactors. Robust and accurate metallic fuel performance models are necessary for the design, safety analysis, and licensing of such reactors. However, metallic fuel performance models are not as mature as ceramic fuel performance models and require additional development. In order to better gauge the accuracy of existing models, identify high-priority models for development, and quantify the improvements made by future model development, ORNL has developed a benchmark problem based on the IFR-1 experiment. This work gathers all relevant information on the IFR-1 experiment and uses it to develop the benchmark problem. It simulates the problem using the fuel performance code BISON and compare the results to post-irradiation examination data from the experiment. Then a sensitivity analysis is performed on the BISON model to determine the benchmark problem’s sensitivity to uncertainty in the input parameters. The results suggest that BISON’s mechanical models require additional development. Plastic deformation is under-predicted in the cladding and axial swelling is over-predicted in the fuel. These problems may be related. Additionally, there is a bias in the temperature which may be a result of uncertainty in the input parameters rather than an issue with the fuel performance models.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2024

Impact of anisotropy on TRISO fuel performance

Manufacturing of tristructural isotropic (TRISO) particles involves the deposition of pyrolytic carbon (PyC) and silicon carbide (SiC) layers using the fluidized bed chemical vapor deposition (CVD) process. The CVD process is known to generate polycrystalline layers with crystallographic textures, which imparts anisotropic thermophysical properties to the layers. Past studies have shown the risk for particle failure increases with an increase in anisotropy. The limit beyond which the anisotropy of PyC layers becomes unacceptable due to failure risk has been identified as a high-priority knowledge gap. This work presents a first systematic study on the effects of anisotropic thermal and mechanical properties on TRISO fuel performance. This computational study, performed using the fuel performance code BISON, investigates how the anisotropy in elasticity and thermal properties affect the stresses, temperature, and failure of a TRISO particle. The influence of other factors, such as operating temperature and particle geometry on the anisotropy effects, also has been analyzed. The studies utilize the recently published anisotropic elasticity and thermal behavior models for TRISO PyC and SiC layers implemented using tensors with full anisotropic capability. The spherical TRISO particles with anisotropic properties were found to have greater maximum tensile stress and significantly higher failure probability than the spherical particles with isotropic properties. In conclusion, the fuel performance predicted using these recently developed models was found to be comparable with the performance obtained using the historical models.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Monolithic ATF MiniFuel Sample Capsules Ready for HFIR Insertion

Several advanced nuclear fuel concepts are being considered throughout the nuclear industry. Implementation of these concepts could increase accident tolerance or enhance performance beyond the capabilities of the UO₂-based nuclear fuel currently in use. Qualification and deployment of any new fuel requires rigorous irradiation testing to demonstrate performance under representative normal and off-normal operating conditions. The traditional approach for qualifying new fuels requires exhaustive execution of many integral fuel tests. However, due to the long timeframe for executing these integral tests and the limited number of available materials test reactors, this approach is becoming impractical. To accelerate fuel qualification, Oak Ridge National Laboratory developed the MiniFuel irradiation vehicle for use in conducting accelerated separate effects irradiation testing of a wide range of nuclear fuel materials in the High Flux Isotope Reactor (HFIR). The first MiniFuel irradiations performed in the facility tested sol gel–derived uranium nitride kernels and tristructural isotropic (TRISO)-coated particle fuels. This report describes the preparation and assembly of the first set of monolithic MiniFuel irradiations conducted to support accident-tolerant fuel (ATF) development and accelerated fuel qualification. Two irradiation targets containing a variety of UO₂ and U₃Si₂ disk fuel specimens were fabricated and assembled for irradiation to burnups of 8-10 and 28-40 MWd/kg U. The target irradiation temperature is 450-550°C. Irradiation of U₃Si₂ will provide new data regarding the irradiation performance of a candidate ATF to complement current ATF-1 integral experiments being performed in the Advanced Test Reactor. UO₂ samples were included as a reference so that the results from the MiniFuel experiments can be compared with the extensive UO₂ fuel performance database. The monolithic MiniFuel capsules were successfully assembled, welded, and tested per HFIR requirements and are ready for insertion into the reactor. Pictures of the assembly process are included in this report. The experiment is planned for insertion into the HFIR during cycle 487 in April 2020.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Prospects for additive manufacturing of nuclear fuel forms

Additive manufacturing (AM) is viewed as a critical enabling technology for achieving superior performance and improved economics across many sectors. Although the past decade has seen increased application of AM methods to nuclear reactor cladding and structural materials, exploration of AM as applied to the uranium-bearing nuclear fuel forms has been limited. The two major families of nuclear fuel forms (monolithic, particle/dispersion) are utilized with their own set of core objectives in mind, and their differences require distinct fabrication infrastructures. These reference fabrication methods impose many limitations on nuclear fuels. Further, both currently operating reactors and future concepts have the potential for improved performance if these accepted limitations are relaxed or removed entirely. The primary limitations of reference fabrication processes for the common nuclear fuel forms are outlined in this paper. This groundwork is then used to identify avenues of fuel performance specific to each of these fuel architectures that could be exploited if the restrictions of conventional fuel fabrication are removed. Moreover, multiple targets for AM studies are laid out for each of the major nuclear fuel variants. Finally, key strategic components to guide research activities in AM of nuclear fuels are outlined, with an emphasis on use of modeling and simulation to motivate research aims and embrace of an accelerated testing methodology to screen and quality new fuel forms.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Reduction of the Waste Occupied Area by Nuclide Separation and Horizontal Emplacement of the Waste Packages - 20422

Two of the key objectives for realizing the advanced nuclear fuel cycle are to reduce the volume of high-level radioactive waste and to reduce the foot-print of the geological repository. To achieve these objectives, research and development on nuclide separation technologies is a prerequisite. In this context, it is necessary to consider the vitrification conditions and the design of the geological repository where separation technologies would be implemented to achieve effective reductions in the volume of vitrified waste and the foot-print of the geological repository. In this study, the effects of the vitrification conditions on the number of vitrified waste units and the disposal area were evaluated, based on the assumption that separation of Cs and Sr from the spent nuclear fuel had been performed. In addition, with reference to the design of the geological repository, the impact on the foot-print of the repository for different emplacement methods of the waste packages was examined. As a result, it was clarified that the waste-occupied area could be reduced by horizontal emplacement of the vitrified waste with low heat generation. In addition, it was demonstrated that a low waste-loaded vitrified waste contributed to a reduction in the foot-print of the geological repository in the case of horizontal emplacement, although the number of vitrified waste units increased. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2023

Testing Instrument Extremes in the TREAT Facility

TREAT is a transient power-shaping reactor whose primary mission is to enhance safety performance by testing nuclear fuels and materials under thermodynamic and neutronic conditions ranging from off-normal to extreme. Transient testing of nuclear fuels is analogous to car crash testing, in that the dramatic changes commonly seen when comparing the test specimens' initial and final state points necessitate in-situ measuring in order to interpret and understand the evolution of the experiment. TREAT’s experiment design strategy utilizes a highly reconfigurable and accessible reactor core that affords flexibility when installing experiment devices, thanks to the lack of a primary coolant boundary and the inclusion of multiple access points in the reactor bioshield. Within the experiment devices, the test specimens (which are integrated with their test environments), desired instrumentation diagnostics, and safety considerations are all contained in a single engineered package. The experiments encompass various types of environments (e.g., water, sodium, and gas at temperature and pressure), as well as a range of control options (e.g., static or flowing coolants). The experimental conditions are uniquely representative of advanced reactors, providing challenges to sensor performance but also affording a unique opportunity for development and qualification of sensors suited to these environments.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2026

3D TRISO particle-explicit compact meshing

The TRI-structural ISOtropic (TRISO) layered fuel particle is a robust nuclear fuel form offering enhanced safety and performance for advanced reactor concepts, including high-temperature gas-cooled reactors and other Generation IV designs. These poppy-seed-sized particles are embedded in a graphite matrix to form fuel elements that must withstand elevated temperatures and high burn-up levels. The heterogeneous nature of these fuel elements — comprising thousands of randomly distributed TRISO particles — produces complex stress fields and thermal gradients that one- and two-dimensional models cannot accurately capture. While three-dimensional modeling has improved predictions of dimensional changes, internal pressure buildup, and fission product transport under irradiation, current approaches rely on homogenized material properties that are known to have considerable divergence from experimental observations. This work presents a methodology for optimized random packing of TRISO fuel compacts and full three-dimensional mesh generation within the BISON fuel performance code, with each particle coating layer individually discretized. The resulting mesh was demonstrated through heat conduction simulations under representative in-reactor operating conditions, showing strong agreement with expected behavior. This capability enables detailed analysis of particle-to-particle interactions, matrix cracking mechanisms, and the statistical distribution of coating layer failures — all of which directly govern fuel performance and safety margins.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2023

Sensitivity of UO 2 fuel performance to microstructural evolutions driven by dilute additives

Use of dilute additives to nuclear fuel is being considered to increase the security of commercial fuel management through traceability of fabricated fuel elements. Taggants, as additives are denoted when included for traceability purposes, may also improve fuel performance, as demonstrated in Cr-containing uranium dioxide as described in the literature, and they may also improve fuel safety. In fact, studies have shown that some additives affect fuel material properties such as grain size and density after sintering. Given the possible range of elements that could be used as additives, the impact of such fuel property variations on the fuel’s thermomechanical behavior becomes relevant. These effects can be evaluated through a sensitivity study of standard fuel models to analyze changes in these properties using a fuel performance code. In this work, the BISON code is being used to investigate these effects through a 2D axisymmetric model of smeared UO 2 fuel pellets and ZIRLO® cladding under realistic pressurized water reactor core irradiation conditions. Here, randomly sampled densities and grain sizes within specified ranges are used as input parameters in the simulations, and several fuel model-related outputs are evaluated. The thermomechanical response of the cladding is also addressed in this study. The simultaneous variation of both input parameters offers a more comprehensive path to identify key sensitivities. Outputs explored include temperature, fission gas release, creep, and radial stress. Results show that although most of these outputs are sensitive to grain size to a certain extent, density mainly affects fuel temperature and elastic strain. Furthermore, sensitivities can vary depending on the radial position within the fuel pellet.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Quantifying deformation during Zry-4 burst testing: a comparison of BISON and a combined in-situ digital image correlation and infrared thermography method

The development and verification of nuclear fuel-cladding performance codes require extensive testing to establish empirical correlations, necessitating more accelerated testing methods that can replace large validation studies. Here, in the present work, a technique was developed and implemented to experimentally quantify the relationship between temperature, cladding internal pressure, and strain in-situ during a burst test, with the specific aim of generating data for code validation and model refinement. Digital image correlation was used to measure hoop, axial, and radial strain, and infrared thermography to quantify axial temperature gradients. Several key experimental modifications to traditional LOCA burst testing were necessary, but are shown to effectively have little impact on burst temperatures. The time/temperature dependent pressure and time/spatially dependent thermal gradient data were used with BISON to simulate cladding burst and strain rates. Although the measured DIC strains reach appreciable amounts at slightly lower temperatures than BISON simulated strains, there is good agreement between the measured and simulated strains in terms of magnitude and rates leading up to burst. However, in the few seconds prior to and during burst, the BISON simulated strains are significantly lower than the measured strains, indicating the potential for model improvement. The combined experiment and simulation technique may be applied to any new cladding concept to accelerate fuel qualification.

36 MATERIALS SCIENCE↗
DOE OSTI2022

Phase-field simulations of fission gas bubbles in high burnup UO2 to inform engineering-scale fuel performance modeling

To improve the economics of commercial nuclear energy generation, U.S. utilities are currently seeking licensing approval to operate UO2 fuel to higher burnups. One significant safety issue that must be addressed to obtain approval is the potential for fine fragmentation/pulverization of the fuel during a loss-of-coolant accident (LOCA). The cause of pulverization has been hypothesized to be the rapid increase of pressure in fission gas bubbles in the high burnup region of the fuel during a LOCA. To better understand this phenomenon, a novel phase-field model of the fission gas bubble microstructure in UO2 has been developed and implemented in Idaho National Laboratory (INL)'s Marmot application for phase-field simulation of nuclear materials. Simulations of the bubble response to steady-state and transient conditions were conducted. Simulation results were used to inform a mechanistic model of pulverization in BISON, INL’s fuel performance simulation code.

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2021

Molten Salt Reactors and Electrochemical Reprocessing: Synthesis and Chemical Durability of Potential Waste Forms for Metal and Salt Waste Streams

The molten salt reactor (MSR) is one of the leading advanced nuclear reactor candidates to replace current nuclear reactor technologies in the U.S. Besides having more economical and reliable designs, MSRs have are amenable to a closed fuel cycle, in which electrochemical reprocessing can be performed to recycle the used nuclear fuel. This review intends to provide information about potential waste forms for metal and salt waste streams from these salt-based nuclear processes. Metal waste streams arise from reactor components and structural materials. Salt waste streams are generated during reactor operations as fission products build up in salt-fueled systems. Waste forms that have the highest waste loading and/or have shown the most commercial promise are discussed with an emphasis on the current state of efforts to understand the synthesis and chemical durability of metal and ceramic waste forms.

molten salt reactors, electrochemical reprocessing↗
DOE OSTI2021

Engineering Scale Drying of Aluminum-Clad Spent Nuclear Fuel: Experiment Report

Engineering-scale tests were performed to evaluate the relative effectiveness of forced gas and vacuum-drying processes on aluminum-clad spent nuclear fuel (ASNF) in preparation for extended dry storage. Drying models were developed to improve confidence in the likely range of conditions at the start of dry storage and to understand the factors most significant to each process. Testing was performed at the Holtec International Forced Helium Dehydration training facility in Camden, New Jersey, by students from the University of South Carolina in collaboration with Idaho National Laboratory. A full-size Type 1a basket, with a full-diameter vessel configuration (based on the Department of Energy standardized canister design), was used in combination with a 10 assembly surrogate ASNF arrangement to provide a proxy for geometry. A resistance heater incorporated in one assembly simulated the influence of 100 W decay heat. This instrumented chamber allowed testing of the removal of bulk water, physisorbed water, and chemisorbed water over a range of operating parameters with either drying process. Thick oxide films were grown on aluminum test plates to mimic the ASNF surface chemistry. These one-use test plates were housed within select assemblies during drying. Post-test analysis of these plates gave a measure of the moisture removed during each test, which was compared to a control. Instrumentation provided detailed thermal, humidity, and gas or pressure data relevant to each test. Model simulations generally compared favorably to instrument data for the tests. While both processes were able to remove bulk water, removal of chemisorbed water was shown to depend heavily on local temperature. To the disadvantage of vacuum drying, operations approaching or exceeding 220°C achieved consistently more dehydroxylation.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

2025 Intern Poster

The Hot Fuel Examination Facility (HFEF) at the Materials and Fuels Complex (MFC) houses the largest U.S. inert atmosphere hot cell for nuclear material research. Key features include the precision gamma scanning (PGS), Fuel Accident Condition Simulator (FACS), Neutron Radiography Reactor (NRAD), and the focus of this project, the Metallograph Loading Cell (MET Cell). The MET Cell performs tests on spent nuclear fuel, such as microhardness testing, microscopy, and neutron radiography. However, the MET Cell’s existing pressure and lighting control systems are outdated and inefficient, with inadequate documentation for system changes over time. This project aims to design a new automated control system for the MET Cell, ensuring longevity (minimum ten years), ease of troubleshooting/repair, and integration into the building monitoring system. The design process addressed challenges such as space restrictions, varied voltages within enclosures, sourcing new components, and security limitations. Compliance with NFPA 70, UL508A, MFC Physical Security, and INL Engineering standards was essential. The project involves repurposing an existing PLC to manage lighting and pressure control using digital and analog signals, simplifying wiring, and ensuring thorough documentation for future reference.

42 - ENGINEERING↗
DOE OSTI2022

Development of Plant Reload Optimization Framework Capabilities for Core Design and Fuel Performance Analysis

The United States (U.S.) nuclear industry faces a challenge in maintaining required levels of safety while ensuring economic competitiveness to stay in business. Safety remains a key parameter for all aspects of light water reactor (LWR) nuclear power plant (NPP) operations. Safety can become more economical by using a risk-informed ecosystem, such as the one being developed by the Risk-Informed Systems Analysis (RISA) Pathway under the U.S. Department of Energy (DOE) Light Water Reactor Sustainability (LWRS) Program. The LWRS Program promotes a wide range of research and development activities with the goal of maximizing both the safety and economic efficiency of NPPs through improved scientific understanding, especially given many plants are now considering second license renewals. The RISA Pathway has two main goals: (1) deploy methodologies and technologies that better represent safety margins and cost and safety factors and (2) develop advanced applications that enable cost-effective plant operation. The Plant Reload Optimization Platform development project aims to build a reactor core design tool that includes reactor safety and fuel performance analyses, and also uses artificial intelligence to support optimization of core design solutions. This report summarizes Fiscal Year 2022 (FY-22) activity in platform capability developments in RAVEN. This platform performs simulations using industry codes for core design (i.e., PARCS) and fuel performance (i.e., TRANSURANUS) which will allow expansion of the capabilities to include advanced fuel designs such as accident-tolerant fuel (ATF)s with high burnup.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2024

SCALE Demonstration for Sodium-Cooled Fast Reactor Fuel Cycle Analysis

In support of the US Nuclear Regulatory Commission non-light-water reactor fuel cycle demonstration project, SCALE 6.3.1 capabilities for radionuclide characterization, criticality, and shielding were demonstrated for scenarios in the sodium-cooled fast reactor (SFR) nuclear fuel cycle. Three postulated accident scenarios were selected for analysis in this work. As a basis for all scenarios, irradiated fuel inventories were generated using SCALE/ORIGAMI. To cover multiple SFR design choices, two different types of SFR fuel, uranium/transuranic-loaded and U-based fuels, were considered. For the first scenario, SCALE/MAVRIC was used to calculate the radiation shielding and dose rates inside and outside of the containment building due to a drop of a spent fuel assembly from the fuel-handling system during unloading inside the containment building. For the second scenario, potential critical configurations in an electrofiner were investigated through criticality calculations with SCALE/CSAS. For the third scenario, the activity of the waste salt from an electrorefiner was evaluated using SCALE/ORIGEN. The dose rate produced by the analyzed SFR assemblies is similar to that produced by a typical pressurized water reactor (PWR) fuel assembly with a discharge burnup of 50 GWd/MTU, with the same cooling time of 10 days. The criticality analyses suggested that the different electrorefiner configurations have a large margin to criticality. The activity analysis of the electrofiner waste revealed that shielding and cooling may be required for the waste salt that contains transuranics and fission products produced by the electrorefiner because of the high activity of the waste salt. In general, the application of various capabilities in the SCALE code system for SFR fuel inventory generation, criticality, and shielding was successfully demonstrated for the selected scenarios in the SFR nuclear fuel cycle. Additional analyses can be performed to provide more accurate results when more details of the SFR nuclear fuel cycles are available, for example, the dimension of the electrorefiner and the salt compositions during reprocessing.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Demand Driven Cycamore Archetypes

Future nuclear fuel cycle options may present advantages over today’s once-through fuel cycle. Nuclear fuel cycle simulation tools assess the performance of those fuel cycles as well as the dynamics of long-term technology transitions. In many nuclear fuel cycle simulation tools, it has historically been the responsibility of the user to manually define facility deployment schemes and all facility parameters. While this is straightforward in simple fuel cycles, transitions from one fuel cycle to another can be more complex. In particular, deployment schemes for supportive fuel cycle facilities beyond the reactor become complex if the analyst desires to avoid gaps in the nuclear fuel and power supply chain during those transition scenarios. As nuclear fuel cycle analysis approaches questions regarding the feasibility and performance of the deployment schemes and technology choices during technology transition, automation of this historically manual process is necessary. The main objective of this work was to develop and demonstrate Cyclus automation capabilities toward key nuclear fuel cycle transition scenarios. While deploying reactors to meet power demand is trivial, and existed in the earliest versions of CYCLUS, automated, predictive deployment and decommissioning of other facilities is more complex. These include mining, milling, enrichment, fuel fabrication, reprocessing, and others. For example, a balanced closed fuel cycle may require ensuring that there is enough fast reactor fuel for their operation and may drive deployment of a fleet of light water reactors. This concern comprises the main challenge that drove the project effort. The Demand-Driven Cycamore Archetype project (NEUP-FY16-10512) aimed to develop CYCAMORE demand-driven deployment capabilities and thereby automate transition scenario definition. The developed software package, d3ploy, in the form of a CYCLUS Institution agent, deploys Facilities to meet the front-end and back-end demands of the fuel cycle. The University of South Carolina and the University of Illinois applied multiple algorithmic approaches to this challenge. This project developed an in situ demand-driven development schedule calculation through non-optimizing, deterministic-optimizing, and stochastic-optimizing algorithms as CYCLUS archetypes and demonstrated these new archetypes in program-supporting fuel cycle transition scenarios. Both objectives were achieved. This report documents the results and deliverables obtained toward these achievements in detail.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2020

Cluster dynamics simulation of xenon diffusion during irradiation in UO 2

Diffusion of fission gas in UO 2 nuclear fuel impacts several important performance metrics, such as fission gas release, swelling, and thermal conductivity. Current empirical models of fission gas release have significant uncertainty, some of which derives from the bulk diffusion rate and its dependence on, for example, fuel chemistry and irradiation. In this work, we have applied the previously-developed Free Energy Cluster Dynamics (FECD) methodology in the code Centipede to calculate xenon cluster concentrations in UO 2 under intrinsic (high temperature) and irradiation-enhanced (intermediate temperature) conditions in order to develop a model of the xenon diffusion coefficient based on the atomic scale mechanisms responsible for transport. While the diffusion mechanism for xenon in UO 2 is adequately described by the Xe + U 2 O vacancy cluster for intrinsic conditions, a similar process is not capable of capturing measured in-pile fission gas diffusivity at intermediate temperatures. Therefore, a different diffusion mechanism must dominate under this regime. Using calculated atomistic data, we have shown that irradiation-enhanced diffusion at intermediate temperatures occurs via the larger Xe + U 4 O y vacancy clusters, which have lower migration barriers and increase in concentration by several orders of magnitude compared to intrinsic conditions. This mechanism is enabled by the increased uranium vacancy concentration under irradiation due to Frenkel pair production. In addition, the fast migration of uranium interstitials with two attached oxygen interstitials lowers the total uranium interstitial concentration through reactions with sinks. This allows the extended defects, such as Xe + U 4 O y vacancy clusters, to maintain high concentrations by limiting annihilation with attached vacancies. Furthermore, predictions using the Xe + U 4 O y diffusion mechanism are in good agreement with experiment, albeit with some differences in the Arrhenius slope, which we believe may be related to either experimental or model parameter uncertainty. Lastly, an analytical expression suitable for application in fuel performance simulations was derived to capture the predictions of the Centipede simulations.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗