Search NASA⌕ Search

SEARCH · Search NASA

Results for “PRESSURE COEFFICIENT”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

On the use of external burning to reduce aerospace vehicle transonic drag

The external combustion of hydrogen to reduce the transonic drag of aerospace vehicles is currently being investigated. A preliminary analysis based on a constant pressure control volume is discussed. Results indicate that the specific impulse of the external burning process rivals that of a turbojet and depends on the severity of the initial base drag as well as on the Mach flight number and the equivalence ratio. A test program was conducted to investigate hydrogen-air flame stability at the conditions of interest and to demonstrate drag reduction on a simple expansion ramp. Initial test results are presented and compared with the control-volume analysis. The expansion ramp surface pressure coefficient showed little variation with fuel pressure and altitude, in disagreement with the analysis. Flame stability results were encouraging and indicate that stable combustion is possible over an adequate range of conditions. Facility interference and chemical kinetics phenomena that make interpretation of subscale ground test data difficult are discussed.

Trefny, Charles J.↗
NASA NTRS2021

Performance Assessment of Fluidic Oscillators Tested on the NASA Hump Model

Flow separation control over a wall-mounted hump model was studied experimentally to assess the performance of fluidic oscillators (sweeping jet actuators). An array of fluidic oscillators was used to control flow separation. The results showed that the fluidic oscillators were able to achieve substantial control over the separated flow by increasing the upstream suction pressure and downstream pressure recovery. Using the data available in the literature, the performance of the fluidic oscillators was compared to other active flow control (AFC) methods such as steady blowing, steady suction, and zero-net-mass-flux (ZNMF) actuators. Several integral parameters, such as the inviscid flow comparison coefficient, pressure drag coefficient, and modified normal force coefficient, were used as quality metrics in the performance comparison of the AFC methods. These quality metrics indicated the superiority of the steady suction method, especially at lower excitation amplitudes that is followed by the fluidic oscillators, steady blowing, and the ZNMF actuators, respectively. An aerodynamic figure of merit (AFM) was also constructed using the integral parameters and AFC power usage. The AFM results revealed that, for this study, steady suction was the most efficient AFC method at lower excitation amplitudes. The steady suction loses its efficiency as the excitation amplitude increases, and the fluidic oscillators become the most efficient AFC method. Both the steady suction and the fluidic oscillators have an AFM > 1 for the range tested in this study, indicating that they provide a net benefit when the AFC power consumption is also considered. On the other hand, both the steady blowing and ZNMF actuators were found to be inefficient AFC methods (AFM < 1) for the current configuration. Although they improved the flow field by controlling flow separation, the power requirement was more than their benefit.

Fluidic oscillators↗
NASA NTRS1992

Pressure measurements on a rectangular wing with a NACA0012 airfoil during conventional flutter

The Structural Dynamics Division at NASA LaRC has started a wind tunnel activity referred to as the Benchmark Models Program. The primary objective of the program is to acquire measured dynamic instability and corresponding pressure data that will be useful for developing and evaluating aeroelastic type CFD codes currently in use or under development. The program is a multi-year activity that will involve testing of several different models to investigate various aeroelastic phenomena. The first model consisted of a rigid semispan wing having a rectangular planform and a NACA 0012 airfoil shape which was mounted on a flexible two degree-of-freedom mount system. Two wind-tunnel tests were conducted with the first model. Several dynamic instability boundaries were investigated such as a conventional flutter boundary, a transonic plunge instability region near Mach = 0.90, and stall flutter. In addition, wing surface unsteady pressure data were acquired along two model chords located at the 60 to 95-percent span stations during these instabilities. At this time, only the pressure data for the conventional flutter boundary is presented. The conventional flutter boundary and the wing surface unsteady pressure measurements obtained at the conventional flutter boundary test conditions in pressure coefficient form are presented. Wing surface steady pressure measurements obtained with the model mount system rigidized are also presented. These steady pressure data were acquired at essentially the same dynamic pressure at which conventional flutter had been encountered with the mount system flexible.

Rivera, Jose A., Jr.↗
NASA NTRS1996

Alpha-Particle Gas-Pressure Sensor

An approximate model was developed to establish design curves for the saturation region and a more complete model developed to characterize the current-voltage curves for an alpha-particle pressure sensor. A simple two-parameter current-voltage expression was developed to describe the dependence of the ion current on pressure. The parameters are the saturation-current pressure coefficient and mu/D, the ion mobility/diffusion coefficient. The sensor is useful in the pressure range between 0.1 and 1000 mb using a 1 - mu Ci(241) Am source. Experimental results, taken between 1 and up to 200 mb, show the sensor operates with an anode voltage of 5 V and a sensitivity of 20 fA/mb in nitrogen.

Buehler, M. C.↗
NASA NTRS1990

Analytical method for the ditching analysis of an airborne vehicle

A simple analytical method has been introduced for aerohydrodynamic load analysis of an airborne configuration during water ditching. The method employs an aerodynamic panel code, based on linear potential flow theory, to simulate the flow of air and water around an aircraft configuration. The free surface separating the air and water region is represented by doublet" singularities. Although all the theoretical load distributions are computed for air, provisions are made to correct the pressure coefficients obtained on the configuration-wetted surfaces to account for the water density. As an analytical tool, a vortex aerodynamic code is chosen to carry out the present investigation. After assessing· the validity of the method, an application is presented for the water ditching of the Space Shuttle configuration at a 12-deg attitude.

Pressure coefficient↗
NASA NTRS1988

An analytical method for the ditching analysis of an airborne vehicle

A simple analytical method has been introduced for aerohydrodynamic load analysis of an airborne configuration during water ditching. The method employs an aerodynamic panel code, based on linear potential flow theory, to simulate the flow of air and water around an aircraft configuration. The free surface separating the air and water region is represented by doublet sheet singularities. Although all the theoretical load distributions are computed for air, provisions are made to correct the pressure coefficients obtained on the configuration wetted surfaces to account for the water density. As an analytical tool, the Vortex Separation Aerodynamic (VSAERO) code is chosen to carry out the present investigation. After assessing the validity of the method, its first application is to analyze the water ditching of the Space Shuttle configuration at a 12 degree attitude.

Pressure coefficient↗
NASA NTRS2012

Vapor Pressure and Evaporation Coefficient of Silicon Monoxide over a Mixture of Silicon and Silica

The evaporation coefficient and equilibrium vapor pressure of silicon monoxide over a mixture of silicon and vitreous silica have been studied over the temperature range (1433 to 1608) K. The evaporation coefficient for this temperature range was (0.007 plus or minus 0.002) and is approximately an order of magnitude lower than the evaporation coefficient over amorphous silicon monoxide powder and in general agreement with previous measurements of this quantity. The enthalpy of reaction at 298.15 K for this reaction was calculated via second and third law analyses as (355 plus or minus 25) kJ per mol and (363.6 plus or minus 4.1) kJ per mol respectively. In comparison with previous work with the evaporation of amorphous silicon monoxide powder as well as other experimental measurements of the vapor pressure of silicon monoxide gas over mixtures of silicon and silica, these systems all tend to give similar equilibrium vapor pressures when the evaporation coefficient is correctly taken into account. This provides further evidence that amorphous silicon monoxide is an intimate mixture of small domains of silicon and silica and not strictly a true compound.

Ferguson, Frank T.↗
NASA NTRS2006

Computational Analysis of Dual Radius Circulation Control Airfoils

The goal of the work is to use multiple codes and multiple configurations to provide an assessment of the capability of RANS solvers to predict circulation control dual radius airfoil performance and also to identify key issues associated with the computational predictions of these configurations that can result in discrepancies in the predicted solutions. Solutions were obtained for the Georgia Tech Research Institute (GTRI) dual radius circulation control airfoil and the General Aviation Circulation Control (GACC) dual radius airfoil. For the GTRI-DR airfoil, two-dimensional structured and unstructured grid computations predicted the experimental trend in sectional lift variation with blowing coefficient very well. Good code to code comparisons between the chordwise surface pressure coefficients and the solution streamtraces also indicated that the detailed flow characteristics were matched between the computations. For the GACC-DR airfoil, two-dimensional structured and unstructured grid computations predicted the sectional lift and chordwise pressure distributions accurately at the no blowing condition. However at a moderate blowing coefficient, although the code to code variation was small, the differences between the computations and experiment were significant. Computations were made to investigate the sensitivity of the sectional lift and pressure distributions to some of the experimental and computational parameters, but none of these could entirely account for the differences in the experimental and computational results. Thus, CFD may indeed be adequate as a prediction tool for dual radius CC flows, but limited and difficult to obtain two-dimensional experimental data prevents a confident assessment at this time.

Lee-Rausch, E. M.↗
NASA NTRS1973

Unsteady transonic flow analysis for low aspect ratio, pointed wings.

Oswatitsch and Keune's parabolic method for steady transonic flow is applied and extended to thin slender wings oscillating in the sonic flow field. The parabolic constant for the wing was determined from the equivalent body of revolution. Laplace transform methods were used to derive the asymptotic equations for pressure coefficient, and the Adams-Sears iterative procedure was employed to solve the equations. A computer program was developed to find the pressure distributions, generalized force coefficients, and stability derivatives for delta, convex, and concave wing planforms.

Kimble, K. R.↗
NASA NTRS1984

A Navier-Stokes calculation of the airfoil dynamic stall process

A time dependent Navier-Stokes calculation procedure has been applied to the problem of an NACA 0012 airfoil oscillating in pitch in a low Mach number, high Reynolds number environment. The calculated results show many of the known physical features, including sudden suction surface separation, vortices shed at the leading and trailing edges and the return to attached flow at low incidences. Both the lift and moment coefficient curves show the expected features and the calculated wall pressure coefficients show strong correspondence to measured data.

Shamroth, S. J.↗
NASA NTRS1976

Investigation of very low blockage ratio boattail models in the Langley 16-foot transonic tunnel

An investigation at an angle of attack of 0 deg was conducted in a 16 foot transonic tunnel at Mach numbers from 0.4 to 1.05 to determine the limits in Mach number at which valid boattail pressure drag data may be obtained with very low blockage ratio bodies. Extreme care was exercised when examining any data taken at subsonic Mach numbers very near 1.0 and lower than the supersonic Mach number at which shock reflections miss the model. Boattail pressure coefficient distributions did not indicate any error, but when integrated boattail pressure drag data was plotted as a function of Mach number, data which were in error were identified.

Reubush, D. E.↗
NASA NTRS1982

Current band model studies of CH4 at wavelengths less than 2.5 microns

Band model theories are used to calculate the transmission of the methane spectrum. In a band model the monochromatic absorption coefficient over a small wavelength interval is replaced, and an average pressure coefficient is introduced. Two main types of band models were developed. The first is the 'regular' band model, in which the lines in a band are presumed evenly spaced; this is also called the Elsasser band model. In the second type of band model, the lines are randomly spaced; this is often referred to as the Mayor-Goody band model. The methane spectrum is sufficiently irregular that the second band model, the irregular band model, should apply.

Fink, U.↗
NASA NTRS1984

Assessment of preliminary prediction techniques for wing leading-edge vortex flows at supersonic speeds

The applicability of existing theoretical models for predicting wing leading edge separated flow characteristics for high-lift supersonic flight was examined with regard to previous experimental force, pressure and flow visualization data. Correlations of data on uncambered delta wings revealed that the upper surface normal force and minimum pressure coefficients decreased nonlinearly with increasing angles of attack. The attainable vacuum pressure decreased with increasing Mach number, while the lower surface normal force increased nonlinearly with increasing speed. The LISTAR and VORCAM linear theory aerodynamic codes generated predictions for comparison with the data. LISTAR displayed better agreement with measured vortex strength and position and lifting characteristics than did VORCAM. The Euler code SWINT was ill-suited to calculating wing performance in separated flows at high lift and low supersonic speeds.

Wood, R. M.↗
NASA NTRS1987

Surface pressure measurements on the blade of an operating Mod-2 wind turbine with and without vortex generators

Pressure measurements covering a range of wind velocities were made at one span location on the surface of an operating Mod-2, 2500 kW, wind turbine blade. The data, which were taken with and without vortex generators installed on the leading edge, show the existence of higher pressure coefficients than would be expected from two-dimensional wind tunnel data. These high pressure ratios may be the result of three-dimensional flow over the blade, which delays flow separation. Data are presented showing the repetitiveness of abrupt changes in the pressure distribution that occur as the blade rotates. Calculated values of suction and flap coefficients are also presented.

Nyland, Ted W.↗
NASA NTRS1992

Self-, N2, O2, H2, Ar, and He broadening in the nu3 band Q branch of CH4

Self-, N2-, O2-, H2-, Ar-, and He-broadening coefficients, pressure shifts, and integrated intensities have been measured for most transitions in the Q branch of the nu3 fundamental band of methane using a difference-frequency laser spectrometer. A systematic dependence of the broadening coefficients on the tetrahedral symmetry species and order index is observed with striking similarities for N2, O2, and Ar and for H2 and He buffer gases. Comparison with earlier measurements on other bands and branches of methane indicates very little vibrational, branch, or carbon isotope dependence. Dicke narrowing is evident at intermediate pressures, yielding an average narrowing coefficient and an optical diffusion constant for each gas mixture.

Pine, A. S.↗
NASA NTRS1995

Water vapor spectroscopy in the 815-nm wavelength region for Differential Absorption Lidar measurements

The differential absorption lidar (DIAL) technique was first applied to the remote measurement of atmospheric water vapor profiles from airborne platforms in 1981. The successful interpretation of the lidar profiles relies strongly on an accurate knowledge of specific water vapor absorption line parameters: line strength, pressure broadening coefficient, pressure-induced shift coefficient and the respective temperature-dependence factors. NASA Langley Research Center has developed and is currently testing an autonomous airborne water vapor lidar system: LASE (Lidar Atmospheric Sensing Experiment). This DIAL system uses a Nd:YAG-pumped Ti:Sapphire laser seeded by a diode laser as a lidar transmitter. The tunable diode has been selected to operate in the 813-818 nm wavelength region. This 5-nm spectral interval offers a large distribution of strengths for temperature-insensitive water vapor absorption lines. In support of the LASE project, a series of spectroscopic measurements were conducted for the 16 absorption lines that have been identified for use in the LASE measurements. Prior to this work, the experimental data for this water vapor absorption band were limited - to our knowledge - to the line strengths and to the line positions.

Ponsardin, Patrick↗
NASA NTRS1983

Space Shuttle Orbiter Venting: Lessons Learned

The orbiter vent system provides dedicated vent areas to permit the gases trapped inside the vehicle to escape during accent. The same vent system also repressurizes the vehicle during entry. The vent system is one of six systems that constitutes the purge, vent and drain subsystem. The orbiter active vent system has been very adaptable to the changing requirements that have occurred during the development of the Space Shuttle orbiter. Good correlation has been obtained between predicted and measured compartment pressures during the orbital flight test (OFT) program. An investigation of the flight data showed that the difference between preflight prediction and the measured values were primarily due to the difference between the baseline external pressures, which was based on subscale wind tunnel test data, and the actual vehicle local external pressures measured during the flight. The current predictions are based on flight derived vent port pressure coefficients since the wind tunnel data does not adequately define the orbiter ascent pressure environment.

H S Lutfi↗