Search NASA⌕ Search

SEARCH · Search NASA

Results for “Particle”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

A constitutive model for sheared dense suspensions of rough particles

In a concentrated suspension, particles come into contact due to the presence of asperities on their surfaces. As a result, the contact forces and interparticle friction become one of the important factors governing the rheology of rigid particle suspensions at high concentrations. We show that a load-dependent friction model can be used to reproduce the experimentally observed shear thickening [ST—continuous and discontinuous (DST)] behavior with an increase in the asperity size. Increasing the particle surface roughness size leads to a decrease in the critical shear rate above which shear-thickening takes place, a reduction in the critical volume fraction for DST and an increase in the viscosity jump across non-shear-thickened to shear-thickened regime. In this paper, we propose a constitutive model to quantify the effect of increasing the roughness size on the rheology of dense ST suspensions as well as on the critical shear rate for ST and the critical volume fraction for DST. We fit this model to our simulation data for stress controlled shear flow of dense rough particle suspensions. Once the fitting is complete, these equations are used to predict exact volume fractions and shear stress values for transitions between three regimes on the shear stress-shear rate flow state diagram for different roughness values. Furthermore, the results of this study can be used to tune the particle surface roughness for manipulating the dense suspension rheology according to different applications.

42 ENGINEERING↗
DOE OSTI2020

Particle Mass Flow Control and Measurement for High-Temperature Particle Receivers

This work is developing particle flow control and measurement methods for next-generation concentrating solar power systems employing particle-based technologies. Particle receivers are being pursued to provide substantial performance improvements through higher temperatures (>700 °C) for more efficient and cost-effective CSP systems with direct storage for electricity generation, process heating, thermochemistry, and solar fuels production. This specific work will develop technologies that enable more efficient particle receivers and scalable methods to accommodate variable irradiances during commercial on-sun operation. The development of next-generation particle-receiver systems and methods with potentially high consequences for improved performance and cost savings for CSP applications is an appropriate role for the government.

14 SOLAR ENERGY↗
DOE OSTI2021

Gen 3 Particle Pilot Plant (G3P3) -- High-Temperature Particle System for Concentrating Solar Power (Phases 1 and 2)

The U.S. Department of Energy Solar Energy Technologies Office initiated the Generation 3 Concentrating Solar Power (CSP) program to achieve higher operating temperatures (>700 °C) to enable next-generation CSP high-temperature power cycles such as the supercritical CO 2 (sCO2) Brayton Cycle. Three teams were selected to pursue high-temperature gas, liquid, and solid pathways for the heat-transfer media. Phases 1 and 2, which lasted from 2018 – 2020, consisted of design, modeling, and testing activities to further de-risk each of the technologies and develop a design for construction, commissioning, and operation of a pilot-scale facility in Phase 3 (2021 – 2024). This report summarizes the activities in Phases 1 and 2 for the solid-particle pathway led by Sandia National Laboratories. In Phases 1 and 2, Sandia successfully de-risked key elements of the proposed Gen 3 Particle Pilot Plant (G3P3) by improving the design, operation, and performance of key particle component technologies including the receiver, storage bins, particle-to-sCO2 heat exchanger, particle lift, and data acquisition and controls. Modeling and testing of critical components have led to optimized designs that meet desired performance metrics. Detailed drawings, piping and instrumentation diagrams, and process flow diagrams were generated for the integrated system, and structural analyses of the assembled tower structure were performed to demonstrate compliance with relevant codes and standards. Instrumentation and control systems of key subsystems were also demonstrated. Together with Bridgers & Paxton, Bohannan Huston, and Sandia Facilities, we have completed a 100% G3P3 tower design package with stamped engineering drawings suitable for construction bid in Phase 3.

14 SOLAR ENERGY↗
DOE OSTI2022

Technoeconomics of Particle-based CSP Featuring Falling Particle Receivers with and without Active Heliostat Control

This report documents the results and conclusions of a recent project to understand the technoeconomics of utility-scale, particle-based concentrating solar power (CSP) facilities leveraging unique operational strategies. This project included two primary objectives. The first project objective was to build confidence in the modeling approaches applied to falling particle receivers (FPRs) including the effect s of wind. The second project objective was to create the necessary modeling capability to adequately predict and maximize the annual performance of utility-scale, particle-based CSP plants under anticipated conditions with and without active heliostat control. Results of an extensive model validation study provided the strongest evidence to date for the modeling strategies typically applied to FPRs, albeit at smaller receiver scales. This modeling strategy was then applied in a parametric study of candidate utility-scale FPRs, including both free-falling and multistage FPR concepts, to develop reduced order models for predicting the receiver thermal efficiency under anticipated environmental and operating conditions. Multistage FPRs were found to significantly improve receiver performance at utility-scales. These reduced order models were then leveraged in a sophisticated technoeconomic analysis to optimize utility-scale , particle-based CSP plants considering the potential of active heliostat control. In summary, active heliostat control did not show significant performance benefits to future utility-scale CSP systems though some benefit may still be realized in FPR designs with wide acceptance angles and/or with lower concentration ratios. Using the latest FPR technologies available, the levelized-cost of electricity was quantified for particle-based CSP facilities with nominal powers ranging from 5 MW e up to 100 MW e with many viable designs having costs < 0.06 $/kWh and local minimums occurring between ~25–35 MW e .

14 SOLAR ENERGY↗
NASA NTRS1974

Low energy (10eV to 10 keV) equatorial particle fluxes and soft particle fluxes near the equator

Several spectra are shown that represent one rotation of ISIS-1. Spectra 1, 2, 3, represent particles moving down the field line into northern ionosphere and spectra 4, 5, 6 represent particles moving up field lines towards the magnetic equator. The former are direct fluxes and the latter are albedo fluxes. The spectra observed are remarkably similar to these observed in the auroral zone. The direct fluxes exhibit a relative maximum in the few keV range and the albedo a power low spectrum with increased fluxes at low energies. Examination of concurrent topside sounder data on ISIS-1 revealed a positive correlation between a region of turbulent ionosphere and particle fluxes. This ionospheric condition is referred to as equatorial spread F and has been studied extensively with bottomside ionospheric sounders and backscatter radars. The perigee of ISIS crossed the magnetic equator at four local times (0400, 1000, 1600, 2100) during the lifetime of the particle spectrometer. No fluxes were observed at 0400 and 1000 local time. At 1600 a few instances of particles were observed. At 2100 essentially all passes included detectable equatorial fluxes. This is in agreement with the frequency of occurence of equatorial spread F.

Winningham, J. D.↗
NASA NTRS1984

The movement of particles in liquid metals under gravity forces and the interaction of particles with advancing solid-liquid interface

The problems of shrinkage and gas porosity are discussed. Gravity forces enhance the removal of gas bubbles from a metal melt and contribute to the feeding of shrinkage porosity in castings. Experiments are reviewed which determine how large a density difference is required for metal particles to float or sink in a metal melt and to what extent do factors not considered in Stokes Law influence particle movement in a real system. As to the interaction of particles with an advancing solid-liquid interface, the results indicate that the metal particles are not rejected in a metal melt, and that concentrations of particles in a metal following solidification are due to other factors.

Weinberg, F.↗
NASA NTRS1985

A bi-directional charged particle telescope to observe flux, energy spectrum and angular distribution of relativistic and non-relativistic particles

A Charged Particle Telescope (CPT) was designed, fabricated and calibrated to make the following observations: (1) discrimination between various singly charged particles, e.g., electrons, muons and protons, in about 5 to 100 MeV energy range; (2) measurement of the flux and the energy of the charged particles incident to the telescope from two opposite directions and stopping in the telescope, thus obtaining flux and energy spectrum of downward and upward moving charged particles; and (3) measurement of the broad angular distribution of selected particles as a function of azimuthal angle. This telescope can be used to study low energy electron, muon and proton energy spectra. The experiment was flown in a high altitude balloon from Hyderabad, India, in December 1984. This same equipment is also useful in ground level electron, muon spectrum study.

Verma, S. D.↗
NASA NTRS1988

Particle dispersion models and drag coefficients for particles in turbulent flows

Some of the concepts underlying particle dispersion due to turbulence are reviewed. The traditional approaches to particle dispersion in homogeneous, stationary turbulent fields are addressed, and recent work on particle dispersion in large scale turbulent structures is reviewed. The state of knowledge of particle drag coefficients in turbulent gas-particle flows is also reviewed.

Crowe, C. T.↗
NASA NTRS1992

Adaptation of multidimensional group particle tracking and particle wall-boundary condition model to the FDNS code

A particulate two-phase flow CFD model was developed based on the FDNS code which is a pressure based predictor plus multi-corrector Navier-Stokes flow solver. Turbulence models with compressibility correction and the wall function models were employed as submodels. A finite-rate chemistry model was used for reacting flow simulation. For particulate two-phase flow simulations, a Eulerian-Lagrangian solution method using an efficient implicit particle trajectory integration scheme was developed in this study. Effects of particle-gas reaction and particle size change to agglomeration or fragmentation were not considered in this investigation. At the onset of the present study, a two-dimensional version of FDNS which had been modified to treat Lagrangian tracking of particles (FDNS-2DEL) had already been written and was operational. The FDNS-2DEL code was too slow for practical use, mainly because it had not been written in a form amenable to vectorization on the Cray, nor was the full three-dimensional form of FDNS utilized. The specific objective of this study was to reorder to calculations into long single arrays for automatic vectorization on the Cray and to implement the full three-dimensional version of FDNS to produce the FDNS-3DEL code. Since the FDNS-2DEL code was slow, a very limited number of test cases had been run with it. This study was also intended to increase the number of cases simulated to verify and improve, as necessary, the particle tracking methodology coded in FDNS.

Chen, Y. S.↗
NASA NTRS1993

Energetic particle environment in the early solar system - Extremely long pre-compaction meteoritic ages or an enhanced early particle flux

Individual mineral grains from meteorites have been exposed to energetic particles prior to inclusion in the host meteorite matrix, an event which occurred quite early in solar system history. Spallation-produced noble gases in such grains are observed to be orders of magnitude greater in abundance than could be produced after meteorite formation and thus provide a record of precompaction irradiation by energetic particles. If attributed to the contemporary particle environment (current galactic and solar cosmic rays) a minimum exposure time for these grains in the CM parent-body regolith of 150 Myr is obtained, with more realistic models suggesting an active parent body regolith for 300 Myr. Constraints on when meteorite compaction occurred and current models for meteorite evolution suggest that this is unreasonably long, that the time available for exposure to energetic particles on the surface of the parent-body regolith is much less than this. Pre-compaction exposure, compressed into a shorter span of time by constraints on the compaction times of carbonaceous meteorites, would require energetic particle fluxes in excess of those in the contemporary solar system and point toward an active early (T Tauri) sun as its source.

Woolum, Dorothy S.↗
NASA NTRS2012

Particle-Surface Interaction Model and Method of Determining Particle-Surface Interactions

A method and model of predicting particle-surface interactions with a surface, such as the surface of a spacecraft. The method includes the steps of: determining a trajectory path of a plurality of moving particles; predicting whether any of the moving particles will intersect a surface; predicting whether any of the particles will be captured by the surface and/or; predicting a reflected trajectory and velocity of particles reflected from the surface.

Hughes, David W.↗
DOE OSTI2024

Enhanced Detection of Primary Biological Aerosol Particles Using Machine Learning and Single-Particle Measurement

Accurately identifying primary biological aerosol particles (PBAPs) using analytical techniques poses inherent challenges due to their resemblance to other atmospheric carbonaceous particles. Here, we present a study of an enhanced method for detecting PBAPs by combining single-particle measurement with advanced supervised machine learning (SML) techniques. We analyzed ambient particles from a variety of environments and lab-generated standards, focusing on chemical composition for traditional rule-based and clustering approaches and incorporating morphological features into the SML approaches, neural networks and XGBoost, for improved accuracy. This study demonstrates that SML methods outperform traditional methods in quantifying PBAPs, achieving significant improvements in precision, recall, F1-score, and accuracy, leading to an increased number of detected PBAPs by at least 19%. The adaptability of the proposed XGBoost-based SML model is showcased in comparison to traditional methods in categorizing PBAPs for blind data sets from different geographical locations. Two field case studies were investigated, over agricultural land and Amazonia rain forest, representing relatively low and high concentrations of PBAPs, respectively, where XGBoost consistently detected up to 3.5 times more PBAPs than traditional methods. Precise detection of PBAPs in the atmosphere could significantly improve the prediction of climatic impacts by them.

42 ENGINEERING↗
DOE OSTI2023

A search for decays of the Higgs boson to invisible particles in events with a top-antitop quark pair or a vector boson in proton-proton collisions at $$\sqrt{s} = 13\,\text {Te}\hspace{-.08em}\text {V} $$

A search for decays to invisible particles of Higgs bosons produced in association with a top-antitop quark pair or a vector boson, which both decay to a fully hadronic final state, has been performed using proton-proton collision data collected at $\sqrt{s} = 13$ TeV by the CMS experiment at the LHC, corresponding to an integrated luminosity of 138fb -1 . The 95% confidence level upper limit set on the branching fraction of the 125 GeV Higgs boson to invisible particles, B(H → inv), is 0.54 (0.39 expected), assuming standard model production cross sections. The results of this analysis are combined with previous B(H → inv) searches carried out at $\sqrt{s} = 7$, 8, and 13 TeV in complementary production modes. The combined upper limit at 95% confidence level on B(H → inv) is 0.15 (0.08 expected).

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
NASA NTRS2022

Observations of Particle Number Size Distributions and New Particle Formation in Six Indian Locations

Atmospheric new particle formation (NPF) is a crucial process driving aerosol number concentrations in the atmosphere; it can significantly impact the evolution of atmospheric aerosol and cloud processes. This study analyses at least 1 year of asynchronous particle number size distributions from six different locations in India. We also analyze the frequency of NPF and its contribution to cloud condensation nuclei (CCN) concentrations. We found that the NPF frequency has a considerable seasonal variability. At the measurement sites analyzed in this study, NPF frequently occurs in March–May (pre-monsoon, about 21 % of the days) and is the least common in October–November (post-monsoon, about 7 % of the days). Considering the NPF events in all locations, the particle formation rate (J_(SDS)) varied by more than 2 orders of magnitude (0.001–0.6 /cu.cm s) and the growth rate between the smallest detectable size and 25 nm (GR_(SDS-25 nm)) by about 3 orders of magnitude (0.2–17.2 nm/h). We found that JSDS was higher by nearly 1 order of magnitude during NPF events in urban areas than mountain sites. GRSDS did not show a systematic difference. Our results showed that NPF events could significantly modulate the shape of particle number size distributions and CCN concentrations in India. The contribution of a given NPF event to CCN concentrations was the highest in urban locations (4.3 × 10^(3) /cu.cm per event and 1.2 × 10^(3)/cu.cm per event for 50 and 100 nm, respectively) as compared to mountain background sites (2.7 × 10^(3)/cu.cm per event and 1.0 × 10^(3)/cu.cm per event, respectively). We emphasize that the physical and chemical pathways responsible for NPF and factors that control its contribution to CCN production require in situ field observations using recent advances in aerosol and its precursor gaseous measurement techniques.

particle number size distributions↗
NASA NTRSDate not supplied

Heliospheric energetic particle transport: Analysis of near-field-aligned particle propagation for SEP events observed by Wind and MAVEN

Magnetic field alignments of spacecraft over large distances in the heliosphere are rare and are usually very limited in duration. Cruise phases of planetary transfers, however, are an exception to this rule, given the Hohmann-Parker effect. The transfer of the MAVEN s/c in 2014 is one such example. Multiple (~10) solar particle events occurred and were detected at both MAVEN and the Wind s/c, originating from solar activity near the foot points of both s/c. We show initial analysis results of the data collected by the solar wind and energetic particle instruments on both s/c while they were more than 0.2 AU apart, but practically Parker field aligned. Using a 1D model, we present initial simulations in qualitative agreement with energetic electron measurements. Next step is to implement the 2D model with approximate particle release from the Sun, and transport durations between Sun, Earth, and MAVEN. We will discuss implications for this data-model comparison, including the possibility to constrain particle scattering inside 1 AU, as well as its radial dependence between Earth and MAVEN.

Solar Energetic Particles↗
DOE OSTI2021

Structure of Diisobutylene Maleic Acid Copolymer (DIBMA) and Its Lipid Particle as a “Stealth” Membrane-Mimetic for Membrane Protein Research

The study of membrane proteins remains challenging, especially in a native membrane environment. Recently, major progress has been made using maleic acid copolymers, such as styrene maleic acid, to purify membrane proteins and study them directly with native lipids associated with the membrane. Additional maleic acid copolymers, such as diisobutylene maleic acid (DIBMA) membrane-mimetic systems, are being developed and found to have improved spectroscopic properties and pH stability. We studied DIBMA and its lipid particles in solution to better understand its assembly, without and with the lipids, to provide an insight regarding how to use it in solution for better membrane extraction. Using small-angle neutron and X-ray scattering (SANS/SAXS), we show that DIBMA organizes into structures of different size scales at various concentrations and ionic strengths. The polymer performed reasonably well under most solvent conditions except in very low concentrations and high-salt conditions that could result in limited interaction with lipids. To explore DIBMA lipid particles as a suitable membrane-mimetic system for neutron scattering studies of membrane proteins, we measured and determined the contrast-matching point of DIBMA to be ~12% (v/v) D 2 O — similar to that of most protiated lipid molecules but distinct from that of regular protiated proteins — providing a natural contrast for separating their neutron scattering signals. Using SANS contrast variation, we demonstrated that the scattering from the whole lipid particle can be annihilated. Further, we determined that a well-defined lipid nanodisc structure with DIBMA was contrast-matched. These results demonstrate that the DIBMA lipid particle is an outstanding “stealth” membrane-mimetic for membrane proteins. The results provide a structural framework for understanding the organization and assembly process of the polymer itself and the lipid molecules. Such an understanding is imperative for structural techniques such as cryo-electron microscopy, nuclear magnetic resonance, small-angle scattering, and other biophysical techniques.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2022

Particle-based hematite crystallization is invariant to initial particle morphology

Significance Many crystallization processes occurring in nature produce highly ordered hierarchical architectures. Their formation cannot be explained using classical models of monomer-by-monomer growth. One of the possible pathways involves crystallization through the attachment of oriented nanocrystals. Thus, it requires detailed understanding of the mechanism of particle dynamics that leads to their precise crystallographic alignment along specific faces. In this study, we discover a particle-morphology–independent oriented attachment mechanism for hematite nanocrystals. Independent of crystal morphology, particles always align along the [001] direction driven by aligning interactions between (001) faces and repulsive interactions between other pairs of hematite faces. These results highlight that strong face specificity along one crystallographic direction can render oriented attachment to be independent of initial particle morphology.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗