Search NASA⌕ Search

SEARCH · Search NASA

Results for “Polycrystalline material”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1987

Effect of the microstructure on the thermoelectric properties of polycrystalline lanthanum chalcogenides

Small amounts of second phase materials can have important effects on the thermoelectric properties of polycrystalline gamma-La(3-x)X4 (X-S, Te; X in the range of 0 to 1/3). Microscopic examination by SEM of hot pressed La(3-x)Te4 samples has revealed from 1-5 vol. pct of La2O2Te, an amount which is not detected by X-ray powder diffraction measurements. This amount of La2O2Te resulting from oxygen contamination can reduce the concentration of electrons by as much as 10 to 75 percent below the electron concentration calculated for single phase La(3-x)Te4 in the composition range of greatest interest. Small amounts of second phase materials can also lower the lattice thermal conductivity by scattering low frequency phonons. These results indicate that microstructural effects should be considered when electrical and thermal properties of polycrystalline materials are analyzed.

Lockwood, A.↗
DOE OSTI2024

Deconstructing the High Voltage Degradation Mechanisms in Na 2/3 Ni 1/3 Mn 2/3 O 2 with Single Crystals and Advanced Electrolyte

Abstract Sodium layered oxide cathodes can uniquely benefit from the existing lithium‐ion battery industry as sodium‐ion batteries gain traction as a potential low‐cost, drop‐in replacement. However, achieving relevant energy density with a suitable cycle life remains a challenge for sodium layered oxides. At high operating potentials, several competing degradation mechanisms prevent P2‐type Na 2/3 Ni 1/3 Mn 2/3 O 2 (≈550 Wh kg −1 ) from achieving meaningful cycle life—with bulk structural instability and surface reactivity being the primary retractors. Herein, the issue of particle cracking is addressed through detailed synthesis methods of “single‐crystal” materials. By comparison to a polycrystalline baseline, the single‐crystal materials quantify the capacity loss due to isolation of active material caused by intergranular particle cracking. The single crystal materials are then employed in cells with an advanced, “localized saturated electrolyte” (LSE) to demonstrate the magnitude of capacity loss due to electrolyte decomposition at the cathode surface. Mitigation of the surface reactivity through the LSE electrolyte effectively demonstrates the elevated importance of surface reactivity at high voltages despite the onset of egregious particle cracking. This work aims to guide future research into understanding molten‐salt assisted syntheses and advance the debate on surface versus bulk degradation.

Darga, Joe↗
NASA NTRS1991

1000 to 1200 K time-dependent compressive deformation of single-crystalline and polycrystalline B2 Ni-40Al

The 1000-K and 1200-K time-dependent deformation of 100-line-oriented and non-100-line-oriented single crystals of Ni-40Al (made by a modified Bridgman technique) was examined over a large range of strain rates (from 0.1 to 10 to the -7th per sec). The results were compared with those for polycrystalline Ni-40Al made by hot pressing XD synthesized powder. The results from measurements of slow-plastic-strain-rate properties of the two materials show that single crystals offer no strength advantage over polycrystalline material. Both forms were found to deform via a dislocation climb mechanism.

Whittenberger, J. D.↗
DOE OSTI2026

Understanding the Performance Gap between Polycrystalline and Single-Crystal Nickel-Rich Layered Oxide Cathodes

Singe-crystal (SC) nickel-rich layered oxide cathodes, composed of boundary-free particles with high tap density, offer significant advantages in volumetric energy density and mechanical strength compared with polycrystalline (PC) cathode materials. However, as the nickel content increases (≥80%), SC Ni-rich cathodes often suffer from faster performance degradation than PC cathodes of the same composition, and the underlying causes of this discrepancy remain poorly understood. Herein, we reveal the distinct Ni redox behaviors that govern the electrochemical performance of SC and PC Ni-rich cathodes using multiscale and operando characterization techniques. Our results indicate that the increasingly heterogeneous Ni oxidation process in SC cathodes leads to the additional irreversible oxygen redox activity that deteriorates both the mechanical and chemical structures. In contrast, PC cathodes, despite with more pronounced surface reconstruction, exhibit greater chemomechanical stability due to homogeneous redox reactions during charging. Consequently, we find that bulk degradation, more than surface reactions, ultimately leads to fast capacity decay of SC Ni-rich cathodes during cycling. In conclusion, this work offers a comprehensive view on the impact of Ni redox evolutions on the chemomechanical stability in Ni-rich layered oxide cathodes, providing new insights into the longstanding performance gap between SC and PC cathodes, and guiding the rational design of Ni-rich cathode architectures.

36 MATERIALS SCIENCE↗
NASA NTRS1977

Monotectic and syntectic alloys. Experiment MA-044

The flight test furnace run of the monotectic and syntectic alloys experiment was successfully performed during the Apollo-Soyuz Test Project mission in July 1975. Examination of the returned sample cartridges and the formal comparative characterization of the low-g and one-g processed samples of lead-zinc and aluminum antimonide were completed. The results for aluminum antimonide show that polycrystalline and multiphased material can be homogenize in space under low-g conditions. Microstructural study on the lead-zinc flight samples shows that complete interdiffusion of lead and zinc had not been achieved, even though the flight data indicated a soak temperature in the miscible region that was 40 K above the published consolute temperature.

Lacy, L. L.↗
NASA NTRS1979

Silicon Solar Cell Process Development, Fabrication and Analysis

Solar cells were constructed from polycrystalline silicon sheet material (10 cm x 10 cm). These cells were made using conventional aerospace methods and serve as the so-called baseline cell for analysis and comparison with cells to be made from similar material, but using optimized processing techniques. Before and during the processing of the baseline cells in a cleaned diffusion tube, control cells were built using the baseline method. All cells were measured on a solar simulator at air mass zero and 28 C. Average efficiency for the baseline cells was 9.5%. Efficiency was found to vary with location in the sheet. Center regions had higher efficiencies whereas corner and edge regions had lower efficiencies. In general, the efficiency falls off with distance from the center of the sheet.

Minahan, J. A.↗
NASA NTRS1990

Future mission opportunities and requirements for advanced space photovoltaic energy conversion technology

The variety of potential future missions under consideration by NASA will impose a broad range of requirements on space solar arrays, and mandates the development of new solar cells which can offer a wide range of capabilities to mission planners. Major advances in performance have recently been achieved at several laboratories in a variety of solar cell types. Many of those recent advances are reviewed, the areas are examined where possible improvements are yet to be made, and the requirements are discussed that must be met by advanced solar cell if they are to be used in space. The solar cells of interest include single and multiple junction cells which are fabricated from single crystal, polycrystalline and amorphous materials. Single crystal cells on foreign substrates, thin film single crystal cells on superstrates, and multiple junction cells which are either mechanically stacked, monolithically grown, or hybrid structures incorporating both techniques are discussed. Advanced concentrator array technology for space applications is described, and the status of thin film, flexible solar array blanket technology is reported.

Flood, Dennis J.↗
NASA NTRS1991

Probabilistic fracture finite elements

The Probabilistic Fracture Mechanics (PFM) is a promising method for estimating the fatigue life and inspection cycles for mechanical and structural components. The Probability Finite Element Method (PFEM), which is based on second moment analysis, has proved to be a promising, practical approach to handle problems with uncertainties. As the PFEM provides a powerful computational tool to determine first and second moment of random parameters, the second moment reliability method can be easily combined with PFEM to obtain measures of the reliability of the structural system. The method is also being applied to fatigue crack growth. Uncertainties in the material properties of advanced materials such as polycrystalline alloys, ceramics, and composites are commonly observed from experimental tests. This is mainly attributed to intrinsic microcracks, which are randomly distributed as a result of the applied load and the residual stress.

Liu, W. K.↗
DOE OSTI2025

A comparative analysis of YOLOv8 and U-Net image segmentation approaches for transmission electron micrographs of polycrystalline thin films

Metallic thin films offer a platform to experimentally study the dynamics of microstructural evolution, but the required transmission electron microscopy (TEM)-based imaging generates complex images that are challenging to segment and quantify. This work provides a comparative analysis of a new YOLOv8 model and an established U-Net model for bright-field TEM images of polycrystals, employing a framework leveraging physical observables to evaluate performance against two hand-traced benchmark datasets. This methodology obviates the comparison of large, diversely structured, and manually labeled datasets that are required to assess performance on a per-image/per-pixel basis. It is found that the YOLOv8 model, adapted for real-time instance segmentation, has up to 43× faster inferencing (NVIDIA GeForce RTX 4090) compared to U-Net and reconstructs hand-traced grain size distributions (GSDs) with excellent fidelity, finding mean diameter within 3% for grains near an optimal magnification; for grains that deviate from the optimal pixel-diameter, the size of small- (large)-diameter grains is systematically over- (under)-estimated. This is partially mitigated by including scale-aware augmentations during training. Moreover, when the bias is corrected post-inference by a rigid shift in distribution, the YOLOv8 model reproduces ground truth GSDs with exceptional fidelity, with statistical tests indicating <5% probability that the distributions are distinct. Based on ground truth data, calibration curves pertaining to this shift can be constructed for a given model. This issue is not present in the U-Net model’s results, indicating that for quantitative measurements where the true size of objects is of interest, special procedures must be implemented for YOLO-based models.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Mechanical behavior of polycrystalline ceramics: Brittle fracture of SiC-Si3N4 materials

Research on the fracture behavior of silicon nitride and silicon carbide is reported along with the role of anion impurities in the fabrication and behavior of magnesium oxide. The results of a survey of crack propagation in SiC and Si3N4 are presented. Studies in the following areas are reported: development of a fracture toughness testing technique, constant moment beam, microcrack examination, and etching techniques.

Ceipold, M. H.↗
NASA NTRS1974

Mechanical behavior of polycrystalline ceramics: Brittle fracture of SiC-Si3N4 materials

Various properties of ceramic materials were investigated. Magnesium oxide and the role of anion impurities were investigated together with the slow crack growth in silicon nitride-silicon carbide ceramics. The oxide program involved development of fabrication techniques for anion doped materials and evaluation of the role of these anions in the hot pressing response, grain boundary diffusion of nickel doped material, grain boundary microhardness, and grain growth. The carbide-nitride work employed commercial materials and the research involved evaluation of a recently reported technique for study of slow crack growth and the development of data for these commercial materials.

Leipold, M. H.↗
NASA NTRS1974

Mechanical behavior of polycrystalline ceramics: Brittle fracture of SiC-Si3N4 materials

The first study area involved magnesium oxide and the role of anion impurities, while the second area was directed toward slow crack growth in silicon nitride-silicon carbide ceramics. The oxide program involved development of fabrication techniques for anion doped materials and evaluation of the role of these anions in the hot pressing response, grain boundary diffusion of nickel doped material, grain boundary microhardness, and grain growth.

Leipold, M. H.↗
DOE OSTI2026

The Influence of Mesoscale Particle Structure on the Electrode Degradation and Resultant Electrochemistry of Lithium Ion Cells With Nickel Rich Lithium Nickel Manganese Cobalt Oxide Positive Electrodes

Nickel-rich lithium nickel manganese cobalt oxide, NMC (LiNi x Mn y Co z O 2 ), materials are desirable positive electrodes in lithium ion batteries, providing high capacity and energy density. The mesoscale structure of NMC materials is commonly a polycrystalline aggregate, providing opportunity for short lithium ion transport distance of the small primary particles, yet facile material handling due to the larger secondary particles. On (de)lithiation the NMC unit cell changes volume, where the anisotropic strain can result in secondary particle fracture. This secondary particle fracture process during cycling has been associated with several degradation modes of NMC materials in LIBs. In this work, a milling process was determined whereby the secondary particles could be pre-fractured with retention of the parent primary particle crystallographic structure, crystallite size, and morphology, providing the ability to unambiguously determine the influence of NMC secondary particle size and mesostructure on resultant functional behavior. The bulk and interfacial properties and electrochemistry of as-received commercially obtained polycrystal NMC811 (LiNi 0.8 Mn 0.1 Co 0.1 O 2 , PC NMC) and its milled MPC NMC counterpart were compared. The smaller secondary particle size, higher surface area MPC NMC was found to result in 1) greater cathode tortuosity, 2) reduced surface Ni on the cycled MPC cathodes consistent with surface reconstruction, and 3) increased Ni deposition on the anodes from cathode-anode crosstalk. These factors manifested in unfavorable electrochemical behavior of MPC with lower functional capacity at both 1C and C/10 rates and higher impedance over extended moderate voltage (dis)charge cycling.

36 MATERIALS SCIENCE↗
NASA NTRS1989

Test Structures For Bumpy Integrated Circuits

Cross-bridge resistors added to comb and serpentine patterns. Improved combination of test structures built into integrated circuit used to evaluate design rules, fabrication processes, and quality of interconnections. Consist of meshing serpentines and combs, and cross bridge. Structures used to make electrical measurements revealing defects in design or fabrication. Combination of test structures includes three comb arrays, two serpentine arrays, and cross bridge. Made of aluminum or polycrystalline silicon, depending on material in integrated-circuit layers evaluated. Aluminum combs and serpentine arrays deposited over steps made by polycrystalline silicon and diffusion layers, while polycrystalline silicon versions of these structures used to cross over steps made by thick oxide layer.

Buehler, Martin G.↗
NASA NTRS1978

Silicon Solar Cell Process Development, Fabrication and Analysis

Ribbon to Ribbon (RTR) solar cells processed from polycrystalline feedstock showed maximum AMO efficiency of 5.6%. Solar cells from single crystalline feedstock showed slightly higher efficiency than those from polycrystalline feedstock, indicating maximum efficiency of about 6.6% with SiO AR coating. Single crystalline control cells gave 11-12% AMO efficiencies demonstrating that the poor performance of the RTR solar was due to the low quality of material itself. Dendritic web solar cells from the standard process showed maximum AMO efficiency of 9.8% while efficiency of control solar cells were around 11-12%. Web solar cells from back surface field (BSF) process indicated maximum AMO efficiency of 10.9%. Some improvement in open circuit voltage was noticed from the BSF process. Small light spot scanning experiments were carried out on the solar cells from Wacker Silso, EFG, RTR, and dendritic web ribbons. Photoresponse results provided information on localized cell performance and grain size in polycrystalline material, and agreed quite well with the cell performance data, such as efficiency, minority carrier diffusion length, and spectral response.

Yoo, H. I.↗