Search NASA⌕ Search

SEARCH · Search NASA

Results for “Positive Transfer”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Sweeping Jet Film Cooling on a Turbine Vane

The cooling performance of sweeping jet film cooling was studied on a turbine vane suction surface in a low-speed linear cascade wind tunnel. The sweeping jet holes consist of fluidic oscillators with an aspect ratio (AR) of unity and a hole spacing of Pd/D = 6. Infrared (IR) thermography was used to estimate the adiabatic film effectiveness at several blowing ratios and two different freestream turbulence levels (Tu = 0.3% and 6.1%). Convective heat transfer coefficient was measured by a transient IR technique, and the net heat flux benefit was calculated. The total pressure loss due to sweeping jet film cooling was characterized by traversing a total pressure probe at the exit plane of the cascade. Tests were performed with a baseline shaped hole (SH) (777-shaped hole) for comparison. The sweeping jet hole showed higher adiabatic film effectiveness than the 777-shaped hole in the near hole region. Although the unsteady sweeping action of the jet augments heat transfer, the net positive cooling benefit is higher for sweeping jet holes compared to 777 hole at particular flow conditions. The total pressure loss measurement showed a 12% increase in total pressure loss at a blowing ratio of M = 1.5 for sweeping jet hole, while 777-shaped hole showed a 8% total pressure loss increase at the corresponding blowing ratio.

Engineering↗

Transport Phenomena in Low Temperature Lithium-Ion Battery Electrolytes

Lithium-ion batteries face low temperature performance issues, limiting the adoption of technologies ranging from electric vehicles to stationary grid storage. This problem is thought to be exacerbated by slow transport within the electrolyte, which in turn may be influenced by ion association, solvent viscosity, and cation transference number. How these factors collectively impact low temperature transport phenomena, however, remains poorly understood. Here we show using all-atom classical molecular dynamics (MD) simulations that the dominant factor influencing low temperature transport in LP57 (1 M LiPF 6 in 3:7 ethylene carbonate (EC)/ethyl methyl carbonate (EMC)) is solvent viscosity, rather than ion aggregation or cation transference number. We find that ion association decreases with decreasing temperature, while the cation transference number is positive and roughly independent of temperature. In an effort to improve low temperature performance, we introduce γ -butyrolactone (GBL) as a low viscosity co-solvent to explore two alternative formulations: 1 M LiPF 6 in 15:15:70 EC/GBL/EMC and 3:7 GBL/EMC. While GBL reduces solution viscosity, its low dielectric constant results in increased ion pairing, yielding neither improved bulk ionic conductivity nor appreciably altered ion transport mechanisms. We expect that these results will enhance understanding of low temperature transport and inform the development of superior electrolytes.

25 ENERGY STORAGE↗

Analysis of the dynamic response of a supersonic inlet to flow-field perturbations upstream of the normal shock

A linearized mathematical analysis is presented for determining the response of normal shock position and subsonic duct pressures to flow-field perturbations upstream of the normal shock in mixed-compression supersonic inlets. The inlet duct cross-sectional area variation is approximated by constant-area sections; this approximation results in one-dimensional wave equations. A movable normal shock separates the supersonic and subsonic flow regions, and a choked exit is assumed for the inlet exit condition. The analysis leads to a closed-form matrix solution for the shock position and pressure transfer functions. Analytical frequency response results are compared with experimental data and a method of characteristics solution.

Cole, G. L.↗

A method for developing K/S boundary conditions

A method for developing the missing general K/S (Kustaanheimo/Stiefel) boundary conditions is presented, with use of the formalism of optimal control theory. As illustrative examples, the method is applied to the transfer between two position and velocity vectors and to the K/S Lambert problem to derive the missing terminal conditions. The necessary equations for a solution are then developed to the K/S Lambert problem with both the fictitious time, s, and the generalized eccentric anomaly, E, as the independent variables. The latter formulation, requiring the solution of only one nonlinear, well-behaved equation in one unknown, E, results in considerable simplification of the problem. This simplification is possible because the energy equation, in the E-formulation, is separable.

Jezewski, D. J.↗

The laminar compressible boundary layer on a rotating sphere with heat transfer

The paper presents a theoretical analysis of the thermal boundary layer induced by an isothermal sphere rotating in an otherwise quiescent fluid. The boundary layer is considered to be laminar and compressible, and the effects of buoyancy and viscous dissipation on torque, heat transfer, and the position of the ideal jet (the plane of impingement of the boundary layer from the Northern and Southern Hemispheres) are taken into account.

Hussaini, M. Y.↗

Adhesion of a bimetallic interface

The Hohenberg-Kohn and Kohn-Sham formalisms are used to examine binding (binding energy as a function of separation) for combinations of the simple metals Al(111), Zn(0001), Mg(0001), and Na(110) in contact. Similar metal contacts between Al, Zn, Mg, and Na are examined self-consistently in an ab initio calculation using the Kohn-Sham formalism. Crystallinity is included using the Aschroft pseudopotential via first order perturbation theory for the electron-ion interaction; and the ion-ion interaction is included exactly via a lattice sum. Binding energy was determined both in the local-density approximation and including gradient corrections to the exchange and correlation energy. Binding was found in all cases. In dissimilar metal contacts, interfacial bonding was greater than that in the weaker material predicting the possibility of metallic transfer. The nonzero position of the energy minimum in like metal contacts is explained in terms of consistency between the Ashcroft pseudopotential and the bulk charge density. Good agreement with experimental surface energies is obtained in the self-consistent calculation when nonlocal terms are included.

Ferrante, J.↗

Tab Interconnect Work Station

Second work station along solar-array assembly line automatically attaches two interconnect tabs to each silicon solar cell. Machine feeds, forms, and cuts tabs from reel of pretinned metal ribbon, transfers tabs into position, and solders them to cell.

Garwood, G.↗

Satellite services system overview

The benefits of a satellite services system and the basic needs of the Space Transportation System to have improved satellite service capability are identified. Specific required servicing equipment are discussed in terms of their technology development status and their operative functions. Concepts include maneuverable television systems, extravehicular maneuvering unit, orbiter exterior lighting, satellite holding and positioning aid, fluid transfer equipment, end effectors for the remote manipulator system, teleoperator maneuvering system, and hand and power tools.

Rysavy, G.↗

Model reference adaptive control of large structural systems

Attention is given to model reference adaptive control procedures that do not require explicit parameter identification for large structural systems. Even though such applications have been shown to be feasible for multivariable systems, provided there exists a feedback gain matrix that makes the resulting input/output transfer function strictly positive real, it is shown here that this constraint is overly restrictive and that only positive realness is required. Subsequent consideration of a simply supported beam reveals that if actuators and sensors are collocated, then the positive realness constraint will be satisfied and the model reference adaptive control will then indeed be suitable for velocity following when only velocity sensors are available and for both position and velocity following when velocity plus scaled position outputs are measured. For both cases, all states are guaranteed to be stable, regardless of system dimension.

Bar-Kana, I.↗

Subliming Layers Would Reveal Aerodynamic Effects

In proposed technique, flow of fluid across surface studied in detail by use of multilayered, multicolored coating. Particularly useful in study of flow of air over small area of aerodynamic surface. By use of this method, incremental determinations made as to friction, transfer of heat, positions of shock waves, and position and extent of turbulence on given surface. Technique applied to surface of model in wind tunnel or to aerodynamics surface on aircraft.

Jensen, Ronald N.↗

Present status and future prospects for ionospheric propagation corrections for precise time transfer using GPS

The ionosphere can be the greatest variable source of error in precise time transfer using Global Positioning System (GPS) satellites. For single frequency GPS users, the ionospheric correction algorithm can provide an approximate 50 percent r.m.s. correction to the time delay, but users who desire a more complete correction must make actual measurements of ionospheric time delay along the path to the GPS satellite. Fortunately, at least three commercial GPS receivers, specifically designed to measure and correct for ionospheric time delay, are now, or soon will be, available. Initial operation with two different types of GPS ionospheric receivers demonstrated a high degree of accuracy in measuring the ionospheric group delay. Results of these measurements are presented. For those who use a model to correct for ionospheric time delay, it is tempting to use daily values of solar 10.7 cm radio flux to correct a monthly average ionospheric time delay model for each day's operation. The results of correlation of daily maximum ionospheric time delay against solar radio flux values show a poor correlation will be obtained by this procedure. Prospects for improving ionospheric corrections during the declining phase of the present solar cycle are discussed.

Klobuchar, John A.↗

Hydrogen maser clocks in space for solid-Earth research and time-transfer applications: Experiment overview and evaluation of Russian miniature sapphire loaded cavity

The Observatoire Cantonal de Neuchatel (ON) is developing for ESTEC a compact H-maser for space use based upon a miniature sapphire loaded microwave cavity, a technique pioneered at VNIIFTRI. Various contacts between West-European parties, headed by ESA, and the Russian parties, headed by ESA, led to the proposal for flying two H-masers on Meteor 3M, a Russian meteorology satellite in low polar orbit. The experiment will include two masers, one provided by ON and the other by VNIIFTRI. T/F transfer and precise positioning will be performed by both a microwave link, using PRARE equipment, and an optical link, using LASSO-like equipment. The main objectives of the experiment are precise orbit determination and point positioning for geodetic/geophysical research, ultra-accurate time comparison and dissemination as well as in-orbit demonstration of operation and performance of H-masers. Within the scope of a preliminary space H-maser development phase performed for ESTEC at ON in preparation to the joint experiment, a Russian miniature sapphire loaded microwave cavity, on loan from VNIIFTRI, was evaluated in a full-size EFOS hydrogen maser built by ON. The experimental evaluation confirmed the theoretical expectation that with a hydrogen storage volume of only 0.65 liter an atomic quality factor of 1.5 x 10(exp 9) can be obtained for a -105 dBm output power. This represents a theoretical Allan deviation of 1.7 x 10(exp -15) averaged on a 1000 s time interval. From a full-size design to a compact one, therefore, the sacrifice in performance due to the reduction of the storage volume is very small.

Busca, G.↗

Robust Stabilizing Compensators for Flexible Structures with Collocated Controls

For flexible structures with collocated rate and attitude sensors/actuators, we characterize compensator transfer functions which guarantee modal stability even when stiffness/inertia parameters are uncertain. While the compensators are finite-dimensional, the structure models are allowed to be infinite-dimensional (continuum models), with attendant complexity of the notion of stability; thus exponential stability is not possible and the best we can obtain is strong stability. Robustness is interpreted essentially as maintaining stability in the worst case. The conditions require that the compensator transfer functions be positive real and use is made of the Kalman-Yakubovic lemma to characterize them further. The concept of positive realness is shown to be equivalent to dissipativity in infinite dimensions. In particular we show that for a subclass of compensators it is possible to make the system strongly stable as well as dissipative in an appropriate energy norm.

Balakrishman, A. V.↗

Wide-Field Infrared Survey Telescope and Starshade Formation Flying Dynamics at Sun-Earth L2

The formation flying of an occulter with a telescope at the Sun-Earth L2 (SEL2) Libration Point can be a challenging problem. A good knowledge of the Restricted Three Body Problem dynamics is required to understand how these two spacecraft interact with each other in the SEL2 unstable environment, and how other perturbations such as Solar Radiation Pressure (SRP) affect their mutual trajectories. This paper focuses on the transfer trajectories to achieve specific relative positions between two spacecraft as they fly in formation at SEL2, andanalyzes the relevance of SRP in this formation, using the Wide-Field Infrared Survey Telescope (WFIRST) and the Starshade occulter as an example. Given that WFIRST and Starshade have very different area-to-mass ratios, SRP will affect their motion in different ways, and their relative position can be key to reduce the V cost. In this paper we intend on providing an explanation on how the relative position between both spacecrafts affects the transfer V from one observation to the other using dynamical system theory and Floquet modes.

Pressure↗

Mineralogical, Elemental and Tomographic Reconnaissance Investigation for CLPS (“METRIC”)

METRIC comprises a suite of two instruments in a Lunar lander that perform X-ray diffraction (XRD) for mineral structure, X-ray fluorescence (XRF) for elemental composition, and X-ray Micro Computed Tomography (XCT) for 3D internal micromorphology. The instruments are accompanied by optical-near IR cameras to provide local geologic context. The Honeybee Robotics PlanetVac pneumatic sampling and transfer system [1],positioned on a lander footpad, will deliver sieved regolith to the X-ray instruments for analysis. The instrument suite is intended for delivery to the lunar surface on a Commercial Lunar Payload Services (CLPS) lander. The METRICXRD/F instrument draws on heritage from the Mars Science Laboratory CheMin instrument [2] and improves upon the design in multiple ways [3]. Like CheMin, Rietveld refinement and full-pattern fitting of METRIC XRD data can identify minerals at a detection limit of ~1 wt.%, quantify their abundances when present at >3 wt.%, and determine mineral composition (e.g., Fo#in olivine) from lattice parameters for minerals present at >5 wt.%[4,5]. An optimized XRF geometry provides for improved detection and quantification of major, minor and trace elements. The METRIC XCT instrument is a miniaturized X-ray Computed Tomography scanner[6]. Lunar regolith is delivered to a 3 mm diameter, 10 mm long graphite tube inside the instrument. The tube is rotated through 360°in 0.9deg.incrementsand a divergent point source X-ray beam is directed through the material. A Charge Coupled Device (CCD)records attenuation images whose brightness and contrast area function of average atomic number and density. Quantitative data, including particle and void sizes, 3D particle shape parameters, modal volumes and pore geometry can be derived from the resulting 3D reconstructions(voxel resolution: 30 μm). Crystal morphologies derived from METRIC XCT data complement the bulk mineralogy determined by the METRIC XRD/F and provide a measure of grain size distribution for the different phases. Taken together, the METRIC instrument suite determines crystal structure, elemental composition and morphology, three principal characteristics of geological materials that are highly useful in determining the origin and subsequent processing of lunar regolith.

Moon↗

Optimizing collimator positions using bayesian optimization in the Fermilab MI-8 transfer line

Collimators are used to minimize losses and to remove particles that would otherwise get lost downstream and irradiate the machine. Finding the optimal jaw positions is time consuming and with the upstream beam properties changing, the collimation settings would need to be readjusted each time. Therefore, a method to optimize collimator positions and to operate them at full capacity in a short time is required for loss control downstream. A study of collimator positions was conducted and a machine learning (ML) model was developed to predict optimal collimator positions. Bayesian Optimization (BO) was used to calculate new jaw positions from the ML model. The results of BO and usage of ML for better performance of the collimation system are presented in this paper.

Babacan, Betiay [Fermilab]↗