Search NASA⌕ Search

SEARCH · Search NASA

Results for “RMS height”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Roughness of the lunar soil

Three stereoscopic close-up photographs taken of the lunar surface by Apollo 11 and 12 astronauts were analyzed to investigate the roughness of the lunar soil at millimeter resolution. Most existing measurements of regolith roughness were based on radar measurements at wavelengths of about 8.6 mm. Several statistical parameters were determined for they landing site. The surace roughness has been found to be nearly Gaussian. The rms slopes were obtained over scales between 0.5 mm and 5 cm. They steadily decrease with increasing scale length from 58 deg to 2 deg and are in reasonable agreement with radar-measured values. The autocorrelation coefficient of the height distribution has also been obtained; it has a scale length of 0.7 mm.

Lumme, K.↗
NASA NTRS1989

Dynamic sea surface topography, gravity and improved orbit accuracies from the direct evaluation of SEASAT altimeter data

A method for the simultaneous solution of dynamic ocean topography, gravity and orbits using satellite altimeter data is described. A GEM-T1 based gravitational model called PGS-3337 that incorporates Seasat altimetry, surface gravimetry and satellite tracking data has been determined complete to degree and order 50. The altimeter data is utilized as a dynamic observation of the satellite's height above the sea surface with a degree 10 model of dynamic topography being recovered simultaneously with the orbit parameters, gravity and tidal terms in this model. PGS-3337 has a geoid uncertainty of 60 cm root-mean-square (RMS) globally, with the uncertainty over the altimeter tracked ocean being in the 25 cm range. Doppler determined orbits for Seasat, show large improvements, with the sub-30 cm radial accuracies being achieved. When altimeter data is used in orbit determination, radial orbital accuracies of 20 cm are achieved. The RMS of fit to the altimeter data directly gives 30 cm fits for Seasat when using PGS-3337 and its geoid and dynamic topography model. This performance level is two to three times better than that achieved with earlier Goddard earth models (GEM) using the dynamic topography from long-term oceanographic averages. The recovered dynamic topography reveals the global long wavelength circulation of the oceans with a resolution of 1500 km. The power in the dynamic topography recovery is now found to be closer to that of oceanographic studies than for previous satellite solutions. This is attributed primarily to the improved modeling of the geoid which has occurred. Study of the altimeter residuals reveals regions where tidal models are poor and sea state effects are major limitations.

Marsh, J. G.↗
NASA NTRS2000

Determination of Surface and Atmospheric Parameters from AIRS/AMSU/HSB Data

AIRS (Atmospheric Infra Red Sounder) is the first of a series of next generation high spectral resolution infrared sounders which will fly on satellite missions in the next decade. AIRS is a 2368 channel grating spectrometer, with spectral resolving power of roughly upsilon /Delta(upsilon) = 1200, which will fly on the EOS Aqua platform in December 2000 accompanied by AMSU A and HSB, which is similar to AMSU B. New methodology has been developed by the AIRS Science Team to analyze AIRS/AMSU/HSB data in the presence of multilayer broken clouds. The baseline AIRS/AMSU products include surface skin temperature, surface spectral emissivity, atmospheric temperature-moisture-ozone profiles and cloud heights and amounts. Research products include CO and CH4 profiles, total CO2 burden, and OLR. This methodology will be briefly described and results will be shown of AIRS Science Team simulations, based on one day of simulated global data.. RMS errors of atmospheric temperature profiles are expected to be better than 1 K for 1 km layer mean temperatures in up to 80% multilayer fractional cloud cover and RMS errors for moisture profiles are better than 15% for 2 km layers throughout the troposphere.

Susskind, Joel↗
NASA NTRS1994

A new approach for determining fully empirical altimeter wind speed model functions

A statistical technique is developed for determining fully empirical model functions relating altimeter backscatter (sigma(sub 0)) measurements to near-surface neutral stability wind speed. By assuming that sigma(sub 0) varies monotonically and uniquely with wind speed, the method requires knowledge only of the separate, rather than joint distribution functions of sigma(sub 0) and wind speed. Analytic simplifications result from using a Weibull distribution to approximate the global ocean wind speed distribution; several different wind data sets are used to demonstrate the validity of the Weibull approximation. The technique has been applied to 1 year of Geosat data. Validation of the new and historical model functions using an independent buoy data set demonstrates that the present model function not only has small overall bias and root mean square (RMS) errors, but yields smaller systematic error trends with wind speed and pseudowave age than previously published models. The present analysis suggests that generally accuracte altimeter model functions can be derived without the use of colocated measurements, nor is additional significant wave height information measured by the altimeter necessary.

Freilich, M. H.↗
NASA NTRS1993

Satellite altimeter measurements of surface wind

Recent analyses of wind speed measurements by the Geosat altimeter showed that the radar cross section is affected by oceanographic factors, particularly by the degree of sea development, which are not directly accounted for in the geophysical model functions (GMF). In the present work, two new GMFs which account for the effects of the actual degree of sea development are proposed. Along with the radar cross section, these models use significant wave height information. One particular version is recommended for applications in oceanographic and climate studies where wind speed (or wind stress) data have to be binned (i.e., averaged over time and/or space intervals). The accuracy of this GMF (overall bias of 0.1 m/s and rms error of about 1.6 m/s) is higher than the accuracy of commonly employed GMFs, while the wave-age-related trend is reduced to a geophysically insignificant level. Finally, the wind speed histograms for the collocated data set are derived and compared with the ground truth data as well as with the histograms yielded by presently known GMFs. It is also shown that the accuracy of altimeter measurements could be increased even further if some additional information on the wave field were available from independent sources (e.g., the dominant wavelength from synthetic aperture radar images).

Glazman, Roman E.↗
NASA NTRS1988

Medium range lagged average forecasts

In this work, the application of the lagged average forecasting (LAF) technique to operational forecasts of the ECMWF is reported. The ECMWF data consist of two 100-day samples of 10-day forecasts of 500-mb geopotential height for winter 1980/81 and summer 1981. the LAF ensemble includes the latest operational forecast, and also forecast for the same verification time started one or more days earlier than the latest one. The focus is on the following two issues: (1) does ensemble averaging improve forecast skill and (2) is the dispersion of the ensemble useful in predicting forecast skill. The LAF technique was used to produce 3, 5, 7, 8, and 9 day forecasts of the 500-mb height field. The results show that the statistically filtered LAF is a marked improvment upon the operational forecast after 5 days. It is found that on a global scale, forecast skill is weakly correlated with the dispersion of the ensemble, as measured by the rms difference between the operational forecast and the statistically filtered LAF.

Dalcher, Amnon↗
NASA NTRS2000

LIDAR Measurements During Aerosols99

The Aerosols99 cruise took place during the period from January 14, to February 8 1999 on the R/V Ron Brown. The cruise track was almost a straight line from Norfolk, Va. to Cape Town, South Africa and afforded the opportunity to sample several different aerosol regimes over the North and South Atlantic. A Micro Pulse LIDAR system was used continually during this cruise to profile the aerosol vertical structure. Inversions of this data illustrated a varying vertical structure depending on the dominant air mass. In clean maritime aerosols in the Northern and Southern Hemispheres the aerosols were capped at 1 km. When a Dust event from Africa was encountered the aerosol extinction increased its maximum height to above 2 km. During a period in which the air mass was dominated by biomass burning from Southern Africa, the aerosol layer extended to 4 km. Comparisons of the aerosol optical depth derived from LIDAR inversion and surface sunphotometers showed an agreement within +/- 0.05 RMS Similar comparisons between the extinction measured with a nephelometer and particle soot absorption photometer (at 19 m altitude) and the lowest LIDAR measurement (75 m) showed good agreement (+/- 0.014/km . The LIDAR underestimated surface extinction during periods when an elevated aerosol layer was present over a relatively clean surface layer, but otherwise gave accurate results.

Voss, Kenneth J.↗
NASA NTRS1972

Tropospheric range error parameters: Further studies

Improved parameters are presented for predicting the tropospheric effect on electromagnetic range measurements from surface meteorological data. Parameters are given for computing the dry component of the zenith radio range effect from surface pressure alone with an rms error of 1 to 2 mm, or the total range effect from the dry and wet components of the surface refractivity, N, and a two-part quartic profile model. The parameters were obtained from meteorological balloon data with improved procedures, including the conversion of the geopotential heights of the balloon data to actual or geometric heights before using the data. The revised values of the parameter k show more latitude variation than is accounted for by the variation of g. This excess variation of k indicates a small latitude variation in the mean molecular weight of air and yields information about the latitude-varying water vapor content of air.

Hopfield, H. S.↗
NASA NTRS1982

Correlation of Preston-tube data with laminar skin friction (Log No. J12984)

Preston tube data within laminar boundary layers obtained on a sharp ten-degree cone in the NASA Ames eleven-foot transonic wind tunnel are correlated with the corresponding values of theoretical skin friction. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The rms scatter of skin friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston tubes in incompressible pipe flows. In contrast to previous works on Preston tube/skin friction correlations, which are based on the physical height of the probe's face, this satisfactory correlation for compressible boundary layer flows is achieved by accounting for the effects of a variable "effective" height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗
NASA NTRS1982

Seasat altimeter timing bias estimation

A technique developed for the solution of time lag bias based on the analysis of sea surface height discrepancies at ground track intersections, prompted by the presence of a time calibration bias in Seasat altimeter data that produced measurement errors in excess of 1 m, is shown to yield a separation of the dominant, once-per-revolution ephemeris error amounting to about 1.5 m rms from the timing error signature. The technique does not depend on precise geoid data, and in application to a global Seasat altimeter data set covering July 28-August 9, 1978, has yielded a time lag value of -81.0 + or - 2 msec. This corroborates the -79.4 msec revised value derived from a reexamination of internal instrument time delays.

Marsh, J. G.↗
NASA NTRS1972

Tropospheric range error parameters: Further studies

Improved parameters are presented for predicting the tropospheric effect on electromagnetic range measurements from surface meteorological data. More geographic locations have been added to the earlier list. Parameters are given for computing the dry component of the zenith radio range effect from surface pressure alone with an rms error of 1 to 2 mm, or the total range effect from the dry and wet components of the surface refractivity and a two-part quartic profile model. The new parameters are obtained, as before, from meteorological balloon data but with improved procedures, including the conversion of the geopotential heights of the balloon data to actual or geometric heights before using the data. The revised values of the parameter k (dry component of vertical radio range effect per unit pressure at the surface) show more latitude variation than is accounted for by the variation of g, the acceleration of gravity.

Hopfield, H. S.↗
NASA NTRS1982

The inverse problem of constructing a gravimetric geoid

Computation of a single geoidal height from gravity acceleration data formally requires that the latter be known everywhere on the earth. A computational procedure based on linear inverse theory for estimating geoidal heights from incomplete sets of data is presented. The same scheme can be used to estimate gravity accelerations from altimetry-derived geoids. The systematic error owing to lack of data and the choice of a particular inverse operator is described by using resolution functions and their spherical harmonic expansions. An rms value of this error is also estimated by assuming a spectrum for the unknown geoid. The influence of the size of the data region, the spacing between data, the filtering applied to the data, and the model weighting function chosen are all quantified in a spherical geometry. The examples presented show that when low degree spherical harmonic coefficients are available - from satellite orbit analysis - a band-passed version of the geoid can be constructed from local gravity data, even with a relatively restricted data set.

Zlotnicki, V.↗
NASA NTRS1990

Cloud altitude determination from infrared spectral radiances

The CO2 slicing method is generally recognized as the most accurate means of inferring cloud altitude from passive infrared radiance observations. The method is applicable to semi-transparent and broken clouds. During the cirrus FIRE and COHMEX field experiments, CO2 channel radiance data suitable for cloud altitude specification were achieved from moderate spectral resolution satellite sounders (NOAA-TOVS and GOES-VAS) and from a High spectral resolution Interferometer Spectrometer (HIS) flown on the NASA U2/ER2 aircraft. Also aboard the ER2 was a down-looking active lidar unit capable of providing cloud top pressure verifications with high accuracy. A third instrument, the Multispectral Atmospheric Mapping Sensor (MAMS) provided 50 meter resolution infrared window data which is used wtih radiosonde data to verify the heights of middle and low level clouds. Comparisons of lidar and MAMS/radiosonde ground truth cloud heights are made with those determined from: high resolution (0.5/cm) HIS spectra, HIS spectra degraded to the moderate resolution (15/cm) of the VAS/TOVS instruments, and spectrally averaged HIS radiances for individual pairs of VAS spectral channels. The results show that the best results are achieved from high resolution spectra; the RMS difference with the ground truth is 23 mb. The RMS differences between the infrared radiance determination and ground truth increase by 35 percent when the spectral resolution is degraded to the moderate spectral resolution of the VAS/TOVS instruments and by 52 to 183 percent, depending upon channel combinations, when only two spectral channels at VAS/TOVS spectral resolution are used.

Smith, William L.↗
NASA NTRS2002

Application of Accelerometer Data to Mars Odyssey Aerobraking and Atmospheric Modeling

Aerobraking was an enabling technology for the Mars Odyssey mission even though it involved risk due primarily to the variability of the Mars upper atmosphere. Consequently, numerous analyses based on various data types were performed during operations to reduce these risk and among these data were measurements from spacecraft accelerometers. This paper reports on the use of accelerometer data for determining atmospheric density during Odyssey aerobraking operations. Acceleration was measured along three orthogonal axes, although only data from the component along the axis nominally into the flow was used during operations. For a one second count time, the RMS noise level varied from 0.07 to 0.5 mm/s2 permitting density recovery to between 0.15 and 1.1 kg per cu km or about 2% of the mean density at periapsis during aerobraking. Accelerometer data were analyzed in near real time to provide estimates of density at periapsis, maximum density, density scale height, latitudinal gradient, longitudinal wave variations and location of the polar vortex. Summaries are given of the aerobraking phase of the mission, the accelerometer data analysis methods and operational procedures, some applications to determining thermospheric properties, and some remaining issues on interpretation of the data. Pre-flight estimates of natural variability based on Mars Global Surveyor accelerometer measurements proved reliable in the mid-latitudes, but overestimated the variability inside the polar vortex.

Tolson, R. H.↗
NASA NTRS1982

Correlation of Preston-tube data with laminar skin friction

Preston-tube data have been obtained on a sharp ten-degree cone in the NASA Ames Eleven-Foot Transonic Wind Tunnel. Data were obtained over a Mach number range of 0.30 to 0.95 and unit Reynolds numbers of 9.84, 13.1, and 16.4 million per meter. The portions of these data, that were obtained within laminar boundary layers, have been correlated with the corresponding values of theoretical skin friction. The rms scatter of skin-friction coefficient about the correlation is of the order of one percent, which is comparable to the reported accuracy for calibrations of Preston-tubes in incompressible pipe-flows. In contrast to previous works on Preston-tube/skin-friction correlations, which are based on the physical height of the probe's face, this very satisfactory correlation for compressible boundary-layer flows is achieved by accounting for the effects of a variable 'effective' height of the probe. The coefficients, which appear in the correlation, are dependent on the particular tunnel environment. The general procedure can be used to define correlations for other wind tunnels.

Reed, T. D.↗
NASA NTRS2001

Crustal Displacements Due to Continental Water Loading

The effects of long-wavelength (> 100 km), seasonal variability in continental water storage on vertical crustal motions are assessed. The modeled vertical displacements (delta-r(sub M)) have root-mean-square (RMS) values for 1994-1998 as large as 8 mm with ranges up to 30 mm, and are predominantly annual in character. Regional strains are on the order of 20 nanostrain for tilt and 5 nanostrain for horizontal deformation. We compare delta-r(sub M) with observed Global Positioning System (GPS) heights (delta-r(sub O)) (which include adjustments to remove estimated effects of atmospheric pressure and annual tidal and non-tidal ocean loading) for 147 globally distributed sites. When the delta-r(sub O) time series are adjusted by delta-r(sub M), their variances are reduced, on average, by an amount equal to the variance of the delta-r(sub M). Of the delta-r(sub O) time series exhibiting a strong annual signal, more than half are found to have an annual harmonic that is in phase and of comparable amplitude with the annual harmonic in the delta-r(sub M). The delta-r(sub M) time series exhibit long-period variations that could be mistaken for secular tectonic trends or post-glacial rebound when observed over a time span of a few years.

vanDam, T.↗
NASA NTRS1977

Backus-Gilbert theory and its application to retrieval of ozone and temperature profiles

The inversion method provides a quantitative evaluation of the trade-off between vertical resolution of a retrieved profile and formal root-mean-square (rms) error due to measurement noise propagation. The problem of retrieving the top-side ozone profile from backscattered ultraviolet (BUV) measurements is considered. For measurements of the type currently being obtained with the Nimbus 4 and AE-E BUV experiments, it is found that a vertical resolution of approximately 0.75 scale height can be achieved for a formal volume mixing ratio profile error of 10%. Other examples include treatments of the retrieval of temperature profiles from measurements in the 15 micron CO2 absorption band for both the terrestrial and Martian atmospheres. Finally, the method is applied to the problem of retrieving temperature profiles of the Jovian planets from measurements in the far infrared pressure induced H2 lines to be obtained from the Mariner Jupiter/Saturn fly-by missions.

Conrath, B. J.↗
NASA NTRS1978

Verification results for the Spectral Ocean Wave Model (SOWM) by means of significant wave height measurements made by the GEOS-3 spacecraft

Significant wave heights estimated from the shape of the return pulse wave form of the altimeter on GEOS-3 for forty-four orbit segments obtained during 1975 and 1976 are compared with the significant wave heights specified by the spectral ocean wave model (SOWM), which is the presently operational numerical wave forecasting model at the Fleet Numerical Weather Central. Except for a number of orbit segments with poor agreement and larger errors, the SOWM specifications tended to be biased from 0.5 to 1.0 meters too low and to have RMS errors of 1.0 to 1.4 meters. The much fewer larger errors can be attributed to poor wind data for some parts of the Northern Hemisphere oceans. The bias can be attributed to the somewhat too light winds used to generate the waves in the model. Other sources of error are identified in the equatorial and trade wind areas.

Pierson, W. J.↗