Search NASA⌕ Search

SEARCH · Search NASA

Results for “Recovery”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8

Slow Wake Recovery and Low Turbulence Behind Wind Farms Parameterized in Mesoscale Simulations

Numerical weather prediction (NWP) and climate models equipped with wind-farm parameterizations (WFPs) can simulate cluster wake effects affecting downstream wind farms in both onshore and offshore environments. This study evaluates wake recovery behind a wind farm represented by the NWP-WFP approach in the Weather Research and Forecasting (WRF) model using either the Fitch et al. (2012) or Ma et al. (2022a, b) WFPs. Results are benchmarked against large-eddy simulations (LES) of an idealized offshore wind farm with aligned and staggered layouts under neutral atmospheric stability. Near-farm wake recovery is underestimated in NWP-WFP simulations due to its representation on a coarse mesoscale grid. This limitation leads to slow wake recovery through two interconnected mechanisms: (i) spatial gradients in the wind velocity field are weaker compared to LES and (ii) turbulence kinetic energy (TKE) remains low not because of excessive dissipation but due to insufficient shear production caused by these weakened gradients. For the scenario considered here, a wind-speed bias develops in the near-farm wake and persists into the far wake. Differences between the NWP-WFP simulations and LES emerge within a short distance downstream of the farm exit, where the mesoscale simulations recover too slowly. This reduced recovery contributes approximately 0.15-0.50 m s-1 to the near-farm wind-speed bias. The bias established in this region is not subsequently compensated for downstream but instead propagates into the far wake, where wind-speed differences of approximately 0.4-0.6 m s-1 remain up to 50 km downstream. Higher-resolution mesoscale simulations partially reduce this bias. Increasing turbine-added TKE or including subgrid wake effects provides additional improvement, but neither fully addresses the underlying cause. The slow wake recovery is not caused by limitations of the WFPs themselves, as it also occurs outside their region of influence, and adding subgrid wake effects does not significantly impact recovery. Rather, the slow wake recovery is a consequence of mesoscale flow representation. This behavior is not limited to regions downstream of the wind farm but is less visible within the farm, where wake recovery occurs simultaneously with turbine-induced momentum extraction. These results highlight the need for improved representations of wake recovery both within and downstream of wind farms. While enhanced subgrid modeling, shear-driven TKE production, and refined WFP formulations may improve intra-farm dynamics, accurately capturing near-farm wake recovery downstream remains challenging, as WFPs do not act in this region.

17 WIND ENERGY↗

Degradation and Accelerated Recovery of Surface Passivation in n+ Poly-Si/SiOx Passivating Contacts for TOPCon Solar Cells

We studied the surface degradation and recovery of fired poly-Si/SiOx passivating contacts during subsequent dark and illuminated annealing. We report on an industrially-viable path for accelerated recovery of surface passivation. The degradation is influenced by the type of doping in the poly-Si. Phosphorus doped n+ poly-Si/SiOx contacts show degradation followed by recovery, undoped poly-Si/SiOx contacts only show recovery during annealing. Boron doped p+ poly-Si/SiOx contacts show neither degradation nor improvement with annealing. Both degradation and recovery are thermally-activated processes and are completely reversible and cyclic in nature. The activation energy of degradation and recovery in dark for n+ poly-Si/SiOx contacts are 1.27 and 1.33 eV respectively. Dark annealing at elevated temperatures is effective for complete recovery but takes a long time (~30 min at 350 degrees C) due to higher activation energies. Annealing under 7.5 Suns of illumination lowers the activation energy for degradation and recovery to 0.88 and 0.90 eV, respectively. Using this data, we have developed an industrially viable post-firing treatment for accelerated recovery of TOPCon cells by annealing them at elevated temperatures and under intense illumination for a few minutes.

14 SOLAR ENERGY↗

Simulation-Based Recovery Action Analysis Using the EMRALD Dynamic Risk Assessment Tool

Recovery human action is defined as the action that prevents deviant conditions from producing unwanted effects. Analyzing recovery actions has been a critical part in human reliability analysis (HRA). However, there are a couple of limitations to treating recovery actions using only the current HRA methods available. Representatively, the existing recovery analysis does not specifically consider recovery actions as they have occurred in actual nuclear power plants (NPPs). To handle the challenges in the existing recovery analyses, this study suggests a way to analyze recovery actions under a dynamic HRA method, the Procedure-based Risk Investigation MEthod-Human Reliability Analysis (PRIME-HRA) method. The PRIME-HRA method suggests a way on how to develop dynamic simulation models using dynamic risk assessment tools such as the Event Modeling Risk Assessment Using Linked Diagram (EMRALD) [1] and the Human Unimodel for Nuclear Technology to Enhance Reliability (HUNTER) [2]. EMRALD and HUNTER are the dynamic probabilistic risk assessment and HRA tools developed at Idaho National Laboratory. In this paper, differences on analyzing recovery actions in the Technique for Human Error-Rate Prediction (THERP), the Cause-Based Decision Tree (CBDT) and the Korean Standard HRA (K-HRA) and challenges of these approaches are introduced. How we have developed the PRIME-HRA is also introduced in this paper. Then, the proposed approach to analyzing recovery human actions in dynamic context is partially discussed with an example.

99 GENERAL AND MISCELLANEOUS↗

Laboratory simulations of the mixed solvent extraction recovery of dominate polymers in electronic waste

Highlights: • Mixed plastics in e-waste are separated with a solvent extraction method. • Recovery procedure obtained an acceptable recovery rate with high purity. • The recovered plastics are greatly energy-saving compared with virgin polymers. • Cost-saving can be potentially achieved for specific composition of plastics. - Abstract: The recovery of four dominant plastics from electronic waste (e-waste) using mixed solvent extraction was studied. The target plastics included polycarbonate (PC), polystyrene (PS), acrylonitrile butadiene styrene (ABS), and styrene acrylonitrile (SAN). The extraction procedure for multi-polymers at room temperature yielded PC, PS, ABS, and SAN in acceptable recovery rates (64%, 86%, 127%, and 143%, respectively, where recovery rate is defined as the mass ratio of the recovered plastic to the added standard polymer). Fourier transform infrared spectroscopy (FTIR) was used to verify the recovered plastics’ purity using a similarity analysis. The similarities ranged from 0.98 to 0.99. Another similar process, which was denoted as an alternative method for plastic recovery, was examined as well. Nonetheless, the FTIR results showed degradation may occur over time. Additionally, the recovery cost estimation model of our method was established. The recovery cost estimation indicated that a certain range of proportion of plastics in e-waste, especially with a higher proportion of PC and PS, can achieve a lower cost than virgin polymer product. It also reduced 99.6%, 30.7% and 75.8% of energy consumptions and CO{sub 2} emissions during the recovery of PC, PS and ABS, and reduced the amount of plastic waste disposal via landfill or incineration and associated environmental impacts.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

The Impact of Naphthenic Acids on Dynamic Fluid–Fluid Interactions: Implication for Enhanced Oil Recovery

Previous coreflooding results and wettability analyses in our group show that injection of naphthenic-acid-enriched water can improve oil recovery over traditional waterflooding. This observation is still a subject of research efforts without a definitive explanation. Naphthenic acids (NA) have been reported to drive wettability alteration and increase the water–oil interface elasticity. These alterations depend on the NA carbon number and aqueous-phase salinity, among other conditions, as reported in the literature. Smart-water flooding (SWF) research often links recovery to the initial wettability condition, being higher for initially oil-wet rock. SWF refers to a technique in which the aqueous-phase ion composition or/and salinity are changed to maximize oil recovery. Given NAs’ complex solution behavior, selecting acid combinations that prompt oil recovery is a difficult objective. The aim of this research is to determine the effects of select naphthenic acids on the oil–water interfacial rheology and wettability alteration and how these interfacial effects are associated with oil recovery under spontaneous imbibition. NAs were selected based on their carbon number, molecular structure, and solubility in the saline solution used in this research. We aimed at exploring which NAs should be used to regulate interfacial properties so as to either increase oil recovery or accelerate production. Time-domain nuclear magnetic resonance, interfacial dilatational rheology, and liquid-bridge experiments, i.e., proxy of snap-off, were conducted. A baseline was established using results obtained with a previously tested sulfate-rich aqueous phase, shown to be effective in recovering oil. Results show that NA14 and N18 increase the water–oil interfacial viscoelasticity and induce interfacial healing but led to different recovery factors. N10, while effective at inducing water wetness in oil-wet rock, is ineffective at increasing the recovery factor. We concluded that wettability and oil–water interfacial rheology are not exclusive, and instead they can synergistically favor EOR benefits. Moreover, oil recovery benefits under spontaneous imbibition are shown to depend strongly on the initial wettability conditions.

Medina-Rodriguez, Bryan X. (ORCID:0000000262922831↗

Decision-Making Framework to Evaluate Opportunities for Recovery of Rare Earth Elements and Critical Minerals in Produced Water Networks

Oil and gas development activities require a significant amount of water. Given the environmental impacts associated with high consumption and subsequent disposal of this water, there is a need for strategies to support effective reuse of, treatment of, and/or resource recovery from this produced water. These streams can contain appreciable concentrations of rare earth elements (REE) and critical minerals (CM) (e.g., Lithium), which are critical for many important applications in electronics, technology, manufacturing, energy, and medicine [1]. Along with REE/CM present in produced water, other waste streams such as fly ash from coal-fired power plants and acid mine discharge present other potential sources for recovery of REE/CM [2-4]. And with increases in demand for REE/CM, the need for recovery from wastewater streams is becoming even more important. There is a need to develop effective decision-making tools to evaluate the economic and environmental potential for REE/CM recovery from produced water networks while supporting the needs of drilling and hydraulic fracturing activities. In this work, we present our progress in developing a decision-making framework to efficiently design and operate produced water networks for REE/CM recovery. Our approach considers REE/CM recovery from produced water streams alongside other potential wastewater sources. The models consider the location and capacity of storage and decentralized treatment processes as well as the design and operation of pipeline and transportation networks to connect different sources and effectively schedule inventories, reuse, and recovery opportunities. We focus on the evaluation of opportunities for REE/CM recovery with treatment constraints on composition and flow. We demonstrate this framework with an illustrative case study that features diverse production sites, storage facilities, transportation, and treatment sites. This proposed framework will be deployed in an open-source software package that is compatible with the PARETO framework to deliver analysis and decision-making tools that allow stakeholders to quantitatively evaluate potential opportunities for REE/CM recovery in produced water networks.

Pulsipher, Joshua↗

Joint Optimization of Well Completions and Controls for CO 2 Enhanced Oil Recovery and Storage

CO 2 storage through CO 2 enhanced oil recovery (EOR) is considered as one of the technologies to help promote larger scale deployment of CO 2 storage because of associated economic benefits through oil recovery, 45Q tax credits and the utilization of existing infrastructure. The objective of this study is to demonstrate how optimal reservoir management and operation strategies (including well completions and controls) can be used to optimize both CO 2 storage and oil recovery. The optimization problem was focused on jointly estimating the well completions (i.e., fraction of injection/production well perforations in each reservoir layer) and CO 2 injection/oil production controls that maximize the net present value (NPV) in a CO 2 EOR and storage operation. We utilized the newly developed StoSAG algorithm, one of the most efficient optimization algorithms in the reservoir management community, to solve the optimization problem. The performance of joint optimization approach was compared with the performance of well control only optimization approach. In addition, the performance of co-optimization of CO 2 storage and oil recovery approach was compared with the performances of maximization of only CO 2 storage and maximization of only oil recovery approaches. The optimization results showed that a joint optimization of well completions and well controls can achieve an 8.84% higher final NPV than the one obtained from the optimization of only well controls. It was observed that the NPV incremental for joint optimization is mainly due to the fact that the optimal well completions and controls approach results in efficient CO 2 storage and oil production from different reservoir layers depending on the differences in individual layer properties. Comparison of co-optimization (i.e., maximization of NPV) and maximization of only CO 2 storage or only oil recovery showed that the co-optimization and maximization of only oil recovery result in significantly higher final NPV than that obtained through maximization of only CO 2 storage approach while maximization of only CO 2 storage can achieve significantly higher CO 2 storage in the reservoir compared to the other two scenarios. The similar results for co-optimization and maximization of oil production are obtained because of the difference in oil revenue compared to CO 2 storage tax credit. To the best of our knowledge, this is the first study in oil/gas industry and CO 2 storage community to perform joint optimization of well completions and well controls in the fields. We expect that the proposed optimization framework will be a useful and efficient tool for field engineers to optimally manage CO 2 EOR projects to maximize revenue through oil recovery as well as CO 2 storage by taking advantage of the new 45Q tax law.

Artificial intelligence↗

Upset Recovery Human Factors

Accident and incident analyses as well as industry group concerns and recommendations have justified taking a second look at proficiency standards related to upset recovery training and performance. Quite a number of factors and theories have been suggested-- leading the NASA Aviation Safety Program to reconsider manual handling skills in highly automated aircraft particularly in conditions that can potentially lead to Loss of Control events. Our team of Subject Matter Experts (SMEs) first identified 76 Basic Recovery Skills that were important for effective crew response under five different anomaly conditions. In addition to manual handling skills, the skill set included knowledge and cognitive skills, as well as decision making and management skills. Advanced Recovery Skills were identified by combining skills, integrating with crew resource management skills, and developing heuristics for decision making.Using the Advanced Recovery Skill set, the SMEs then developed a generic process flow starting from the problem discovery phase (e.g., identifying an anomaly) through the decision making and management phase (e.g., assessing response options), through the recovery phase (e.g., controlling the aircraft). The generic process flow was refined by testing it against six additional scenarios. The next part of the project was to develop an approach for assessing and revising a generic training curriculum (we used an operators Advanced Qualification Program (AQP) as a framework). Although many of the Basic and Advanced Recovery Skills could be found in the Job Task Listing, they were not always structured or combined in the most effective way. Recommendations were developed for assessing relevant aspects of the Job Task Listing and Continuing Qualification curriculum so that the more comprehensive set of Upset Recovery skillsincluding Human Factors--could be trained and assessed in the most appropriate and effective context. The existing AQP methodology provides a natural way to insert targeted Upset Recovery skills into its system of proficiency objectives, training devices, training activities, and ultimately, into the event sets of a simulator training scenario.

AQP training↗

Contrasting stream nitrate and sulfate response to recovery from experimental watershed acidification

Improvements in air quality have led to ecosystem recovery from acidic deposition, but the mechanisms and trajectories of this recovery are not fully understood. Here, we present long-term stream response and recovery data for paired watersheds at the Bear Brook Watershed in Maine (BBWM) during declining ambient SO 4 and NO 3 in precipitation. East Bear (EB) received ambient deposition from 1989 to 2018; West Bear (WB) received artificially elevated N+S from 1989 to 2016. The WB treatment was discontinued after 2016, the beginning of the recovery from both the experimental N+S and ambient decline. Stream SO 4 in WB gradually declined after the treatment ended, from ~147 µeq L -1 in 2010-16 to ~126 µeq L -1 in 2017-18. The declining S inputs induced desorption of SO 4 from soil phase surfaces, with stream loss far exceeding precipitation input. At the current rate of recovery, it will be many decades before the WB stream returns to pre-treatment SO 4 concentrations. In contrast, NO 3 is only weakly adsorbed in soil, and WB stream NO 3 concentrations rapidly declined from ~39 µeq L -1 in 2010-16 to ~5 µeq L -1 in 2017-18, comparable to the N-limited EB stream. The acid anions are strongly coupled to base cation chemistry in streams, and there was a distinct hysteretic response of Ca and Mg to the chronic acidification, as (Ca+Mg) increased rapidly during the initial years, followed by declining values due to depletion of the soil exchange complex. This 30-year monitoring study (1989-2019) provides insights into recovery mechanisms from acidic deposition and highlights the role of abiotic processes in soil that mediate nutrient cycling and retention. Finally, documenting the rapid response of N alongside the slower recovery for S identifies the temporal resolution necessary for other whole-watershed recovery studies.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Evaluating the role of green infrastructure features in post-disaster recovery – Case Study of Beaumont, Texas after tropical storm imelda

While green infrastructure (GI) can provide multiple environmental benefits, its role in post-disaster economic and social recovery remains relatively underexplored. This article investigates whether different characteristics of GI, such as size, shape, connectivity, and amenities, affect the resilience of local businesses following Tropical Storm Imelda in Beaumont, Texas. The study utilizes SafeGraph mobility data to analyze foot traffic patterns to local businesses before, during, and after the disaster. FRAGSTATS indices measure GI characteristics (e.g., area, shape index, fractal dimension, proximity) while park features such as sports facilities, playgrounds, water features, and accessibility are cataloged through manual observation. Ordinary Least Squares regression models assess the relationship between park characteristics and post-recovery business performance, controlling for demographic variables including income, race, and poverty levels. Results indicate that certain GI attributes significantly enhance business recovery. Points of interest within walking distance (0.5 miles) of parks demonstrated better post-recovery status compared to those beyond this range. Specifically, parks with larger areas (p < 0.01) and more complex shapes measured by fractal dimension index (p < 0.01) had the strongest positive impact on surrounding businesses' recovery. Interestingly, playgrounds showed a negative correlation with recovery (p < 0.05), likely due to flood damage rendering them unusable during the immediate recovery period. Social vulnerability factors, including higher poverty rates and minority populations, negatively affected recovery outcomes despite park proximity.

Economic resilience↗

A review of technologies and performances of thermal treatment systems for energy recovery from waste

Highlights: • The topic of energy recovery from waste by thermal treatment is reviewed. • Combustion, gasification and pyrolysis were considered. • Data about energy recovery performances were collected and compared. • Main limitations to high values of energy performances were illustrated. • Diffusion of energy recovery from waste in EU, USA and other countries was discussed. - Abstract: The aim of this work is to identify the current level of energy recovery through waste thermal treatment. The state of the art in energy recovery from waste was investigated, highlighting the differences for different types of thermal treatment, considering combustion/incineration, gasification and pyrolysis. Also different types of wastes – Municipal Solid Waste (MSW), Refuse Derived Fuel (RDF) or Solid Refuse Fuels (SRF) and some typologies of Industrial Waste (IW) (sludge, plastic scraps, etc.) – were included in the analysis. The investigation was carried out mainly reviewing papers, published in scientific journals and conferences, but also considering technical reports, to gather more information. In particular the goal of this review work was to synthesize studies in order to compare the values of energy conversion efficiencies measured or calculated for different types of thermal processes and different types of waste. It emerged that the dominant type of thermal treatment is incineration associated to energy recovery in a steam cycle. When waste gasification is applied, the produced syngas is generally combusted in a boiler to generate steam for energy recovery in a steam cycle. For both the possibilities – incineration or gasification – cogeneration is the mean to improve energy recovery, especially for small scale plants. In the case of only electricity production, the achievable values are strongly dependent on the plant size: for large plant size, where advanced technical solutions can be applied and sustained from an economic point of view, net electric efficiency may reach values up to 30–31%. In small-medium plants, net electric efficiency is constrained by scale effect and remains at values around 20–24%. Other types of technical solutions – gasification with syngas use in internally fired devices, pyrolysis and plasma gasification – are less common or studied at pilot or demonstrative scale and, in any case, offer at present similar or lower levels of energy efficiency.

09 BIOMASS FUELS↗

Motion Cueing for Stall Recovery Training in Commercial Transport Simulators

Starting in 2019, airline pilots will be required to perform full stall recovery training in flight simulators. Historically, training simulators weren't required to provide training at conditions outside their normal flight envelope. Post-stall aircraft models are generally required to be implemented to simulate the aircraft response after the stall point. In addition, motion cues need to adequately represent this response to ensure the skills learned in simulator training are directly usable in real flight. This paper provides and overview of six simulator experiments conducted at NASA Ames Research Center to develop a motion cueing strategies for stall recovery training in commercial transport simulators. One of the experiments verified an enhanced motion cueing strategy for stall recovery training on a level-D-certified full flight simulator. This study showed that the enhanced motion results in lower maximum roll angles in the stall maneuver, lower minimum load factors in the recovery, lower numbers of secondary stick shakers in the stall recovery, and a lower maximum airspeed in the recovery. These results indicate that relatively minor enhancements to the motion logic of heritage commercial transport simulators can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

stall recovery↗

Motion Cueing for Stall Recovery Training in Commercial Transport Simulators

Starting in 2019, airline pilots will be required to perform full stall recovery training in flight simulators. Historically, training simulators weren't required to provide training at conditions outside their normal flight envelope. Post-stall aircraft models are generally required to be implemented to simulate the aircraft response after the stall point. In addition, motion cues need to adequately represent this response to ensure the skills learned in simulator training are directly usable in real flight. This paper provides and overview of six simulator experiments conducted at NASA Ames Research Center to develop a motion cueing strategies for stall recovery training in commercial transport simulators. One of the experiments verified an enhanced motion cueing strategy for stall recovery training on a level-D-certified full flight simulator. This study showed that the enhanced motion results in lower maximum roll angles in the stall maneuver, lower minimum load factors in the recovery, lower numbers of secondary stick shakers in the stall recovery, and a lower maximum airspeed in the recovery. These results indicate that relatively minor enhancements to the motion logic of heritage commercial transport simulators can significantly improve pilot performance in simulated stall recoveries, and potentially improve stall recovery training.

stall recovery↗

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine**

Abstract Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy‐extensive Haber‐Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source‐separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF‐808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30‐minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

Guo, Lei↗

Modular Functionalization of Metal‐Organic Frameworks for Nitrogen Recovery from Fresh Urine

Nitrogen recovery from wastewater represents a sustainable route to recycle reactive nitrogen (Nr). It can reduce the demand of producing Nr from the energy-extensive Haber-Bosch process and lower the risk of causing eutrophication simultaneously. In this aspect, source-separated fresh urine is an ideal source for nitrogen recovery given its ubiquity and high nitrogen contents. However, current techniques for nitrogen recovery from fresh urine require high energy input and are of low efficiencies because the recovery target, urea, is a challenge to separate. In this work, we developed a novel fresh urine nitrogen recovery treatment process based on modular functionalized metal–organic frameworks (MOFs). Specifically, we employed three distinct modification methods to MOF-808 and developed robust functional materials for urea hydrolysis, ammonium adsorption, and ammonia monitoring. By integrating these functional materials into our newly developed nitrogen recovery treatment process, we achieved an average of 75 % total nitrogen reduction and 45 % nitrogen recovery with a 30-minute treatment of synthetic fresh urine. The nitrogen recovery process developed in this work can serve as a sustainable and efficient nutrient management that is suitable for decentralized wastewater treatment. This work also provides a new perspective of implementing versatile advanced materials for water and wastewater treatment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Service area size assessment for evaluating the spatial scale of solid waste recovery chains: A territorial perspective

Highlights: • A model to evaluate the service area size of a waste recovery chain is proposed. • A recovery performance score is given per waste source. •The areas to be collected in priority are the sources with the highest score. • The score depends on the source's characteristics and the recovery technology. •Replacing anaerobic digestion by composting decreases the facility's spatial scale. - Abstract: Waste recovery is an integrated part of municipal solid waste management systems but its strategic planning is still challenging. In particular, the service area size of facilities is a sensitive issue since its calculation depends on various factors related to treatment technologies (output products) and territorial features (sources waste production and location). This work presents a systemic approach for the estimation of a chain's service area size, based on a balance between costs and recovery profits. The model assigns a recovery performance value to each source, which can be positive, neutral or negative. If it is positive, the source should be included in the facility's service area. Applied to the case of Montreal for food waste recovery by anaerobic digestion, the approach showed that at most 23 out of the 30 districts should be included in the service area, depending on the indicator, which represents around 127,000 t of waste recovered/year. Due to the systemic approach, these districts were not necessarily the closest to the facility. Moreover, for the Montreal case, changing the facility's location did not have a great influence on the optimal service area size, showing that the distance to the facility was not a decisive factor at this scale. However, replacing anaerobic digestion by a composting plant reduced the break-even transport distances and, thus, the number of sources worth collecting (around 68,500 t/year). In this way, the methodology, applied to different management strategies, gave a sense of the spatial dynamics involved in the recovery chain's design. The map of optimal supply obtained could be used to further analyse the feasibility of multi-site and/or multi-technology systems for the territory considered.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DNA damage checkpoint recovery and cancer development

Cell cycle checkpoints were initially presumed to function as a regulator of cell cycle machinery in response to different genotoxic stresses, and later found to play an important role in the process of tumorigenesis by acting as a guard against DNA over-replication. As a counterpart of checkpoint activation, the checkpoint recovery machinery is working in opposition, aiming to reverse the checkpoint activation and resume the normal cell cycle. The DNA damage response (DDR) and oncogene induced senescence (OIS) are frequently found in precancerous lesions, and believed to constitute a barrier to tumorigenesis, however, the DDR and OIS have been observed to be diminished in advanced cancers of most tissue origins. These findings suggest that when progressing from pre-neoplastic lesions to cancer, DNA damage checkpoint barriers are overridden. How the DDR checkpoint is bypassed in this process remains largely unknown. Activated cytokine and growth factor-signaling pathways were very recently shown to suppress the DDR and to promote uncontrolled cell proliferation in the context of oncovirus infection. In recent decades, data from cell line and tumor models showed that a group of checkpoint recovery proteins function in promoting tumor progression; data from patient samples also showed overexpression of checkpoint recovery proteins in human cancer tissues and a correlation with patients' poor prognosis. In this review, the known cell cycle checkpoint recovery proteins and their roles in DNA damage checkpoint recovery are reviewed, as well as their implications in cancer development. This review also provides insight into the mechanism by which the DDR suppresses oncogene-driven tumorigenesis and tumor progression. - Highlights: • DNA damage checkpoint works as a barrier to cancer initiation. • DDR machinary response to genotoxic and oncogenic stress in similar way. • Checkpoint recovery pathways provide active signaling in cell cycle control. • Checkpoint recovery pathway plays a role in overriding tumor barrier in tumorigenesis. • Recovery protein dysregulation and human cancer development is correlated.

60 APPLIED LIFE SCIENCES↗

Monte Carlo-based Transmission and Subtransmission Recovery Simulation of Hurricanes

High-impact low-probability (HILP) events can wreak havoc on electric power systems without appropriate preparedness. In this paper, the recent development of a tool, named Recovery Simulator and Analysis (RSA), is described and demonstrated. While there are many issues to consider when recovering electric power systems, the focus of RSA is on the coordination of transmission and subtransmission recovery with generation dispatch to minimize unserved energy. RSA focuses on recovery simulation to evaluate resilience as part of a planning process. RSA is demonstrated on an approximately 1400-bus Puerto Rican power system for 100 simulated instances of Hurricane Maria. Analysis of the recovery determines how many lines are critical to the recovery and which loads may experience delayed recovery. The results demonstrate the potential uses of RSA for identifying recovery decisions with low unserved energy and for identifying assets critical to recovery which can then be hardened prior to a HILP event.

Maloney, Patrick R.↗