SEARCH · Search NASA
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Altimeter data from a spacecraft borne altimeter was processed to estimate the fine structure of the marine geoid. Simulation studies show that, among several competing parameterizations, the mean free air gravity anomaly model exhibited promising geoid recovery characteristics. Using covariance analysis techniques, quantitative measures of the orthogonality properties are investigated.
The NASA Langley Research Center has the responsibility to advance the state-of-the-art in the area of stall/spin technology. This includes the development and validation of experimental and analytical techniques for the prediction of stall/spin characteristics. As a part of this effort, a rotary balance facility located in the Langley spin tunnel was developed two and a half years ago to rapidly identify an airplane's aerodynamic characteristics in a rotational flow environment. On-line rotary balance data plots and on-line predicted steady spin modes permit the designer to develop, on site, a configuration highly resistant to spins, or one which has good spin characteristics, i.e., no spin equilibrium conditions possible with lateral-directional controls neutral, if the airplane is to be used for acrobatic maneuvers or training. The rotary balance data are also used to compute time histories of a spin's incipient, developed, and recovery phases. These spin analysis techniques and their correlation with spin tunnel model and full-scale flight results are discussed herein.
In this paper, we present the results of raw echo data analysis with data error recovery, data processing, and the calibration results of the je Propulsion Laboratory's airborne synthetic aperature radar for the pacific Rim II mission.
First steps have been taken to qualify a family of parafoil systems capable of increasing the survivability and reusability of high-altitude balloon payloads. The research is motivated by the common risk facing balloon payloads where expensive flight hardware can often land in inaccessible areas that make them difficult or impossible to recover. The Autonomously Navigated Experimental Lander (ANGEL) flight test introduced a commercial Guided Parachute Aerial Delivery System (GPADS) to a previously untested environment at 108,000ft MSL to determine its high-altitude survivability and capabilities. Following release, ANGEL descended under a drogue until approximately 25,000ft, at which point the drogue was jettisoned and the main parachute was deployed, commencing navigation. Multiple data acquisition platforms were used to characterize the return-to-point technology performance and help determine its suitability for returning future scientific payloads ranging from 180 to 10,000lbs to safer and more convenient landing locations. This report describes the test vehicle design, and summarizes the captured sensor data. Various post-flight analyses are used to quantify the system's performance, gondola load data, and serve as a reference point for subsequent missions.
Cost is just as important as power density or efficiency for the adoption of waste heat recovery thermoelectric generators (TEG). Prior work [1] has shown that the system design that minimizes cost (e.g., the $/W value) can be close to the designs that maximize the system’s efficiency or power density, however, it is important to understand the relationship between those designs to optimize TEG performance-cost compromises. Expanding on recent work [1, 2, 3] the impact of heat exchanger conditions on the optimum TEG fill factors and cost scaling of a waste heat recovery thermoelectric generator with a detailed treatment of the hot side exhaust heat exchanger has been investigated further. The effect of the heat lost to the environment and updated relationships between the hot-side and cold-side conductances [4] that maximize power output are considered. The optimum fill factor to minimize TEG energy recovery system costs is strongly dependent on the heat leakage fraction, σ, the mass flow rate of the exhaust, the hot-side heat exchanger effectiveness, heat exchanger UAh, and heat flux. These relationships are explored and characterized for typical exhaust gas-flow conditions to show the inherent design complexities. The heat exchanger costs often dominate the TEG cost equation and it is critical to fully understand the tradeoff between heat exchanger performance, optimum TEG fill factors, and cost to establish potentially optimum design points within the cost-performance design space. This work will explore the design tradeoffs and relationships within the cost-efficiency-power density design space for a typical thermoelectric energy recovery system application. The interplay between optimum TEG fill factors and heat exchanger design can impact system footprint, volume, and mass in weight-sensitive applications. Less-effective, low-cost heat exchangers may outperform higher cost alternatives from a market adoption perspective. This shift of emphasis acknowledging the interdependence of optimum TEG fill factors and heat exchanger performance has significant implications on thermoelectric waste heat recovery systems designs and their operation. In addition, preferred TEG design regimes exist that accommodate reasonable compromises in TE performance and cost. This effort highlights how the optimum fill factor–heat exchanger performance relations couple to these optimum TEG performance-cost domains based on TEG-system-level analyses and provides a focus for future system research and development efforts.
The information presented in this report provides detailed mission and system analysis of the Split Sprint Mission to Mars. These data were generated from September 1987 through July 1988 and involved numerous individuals within Program Development. This mission derives its name from the fact that the total mission payload is split between two vehicles, a cargo vehicle, and a piloted vehicle. The cargo vehicle carries the Mars lander and propellant for the piloted vehicle return to Earth. Then approximately 1 1/2 years later, the piloted vehicle carries the crew on a higher energy "sprint” trajectory to Mars. The advantages of the Split Sprint Mission is that the payload for the piloted vehicle is minimized and the crew would be in space for only 14 months. Mission and system data are presented for a Sprint Mission in the year 2004. Many important aspects of the mission were studied in detail. These include orbital lighting and lifetime analysis, Mars parking orbit selection, Earth departure window analysis, lander descent and ascent performance, vehicle aerobraking requirements, mission orbital maneuvers, and many other analyses listed in the Table of Contents. Emphasis was placed on vehicle performance analysis which ranged from recovery of the Earth departure stages to aerocapture of the Earth Return Capsule. There is also a section describing the computer programs that were used for this study. These programs provide many useful tools for future studies of manned planetary missions. This introductory section will give an overall view of the Split Sprint Mission and describe the orbital operations and vehicles that were studied.
Data centers are energy-intensive facilities with growing demands for efficiency and cost-effective operations. Smaller, more distributed edge inference data centers are expected to proliferate as AI applications require low latency closer to the user of AI tools, which presents a growing opportunity to explore the systems implications of liquid cooling on water and energy use. This study analyzes the implementation of high-temperature liquid cooling systems in a prototypical inference 1-MW data center and explores the potential for heat reuse across varying climates with a goal to optimize energy efficiency, reduce capital and operational costs, and identify opportunities for high-performance cooling and water use reduction infrastructure. This analysis evaluated configurations utilizing a peak day hourly sizing and systems performance spreadsheet to evaluate design and operational conditions from which component sizes, installed cost, operational cost, and performance metrics were determined for the Base case and the Elevated case. The techno-economic analysis included heat reuse applications across a range of heat recovery temperatures and heat rejection options. The analysis shows that high-temperature liquid cooling allows for improved energy efficiency, lower water consumption, and lower capital costs compared to traditional cooling approaches. Transitioning to elevated water inlet/outlet temperatures (50 degrees C/60 degrees C) eliminates the need for chillers, cooling towers, and heat recovery equipment in many scenarios across three distinct climate zones. This results in up to 75% capital cost savings for the cooling and heat recovery equipment, and with significantly reduced water consumption, especially in non-heat reuse applications. Heat generated from data centers can also be repurposed for space heating, domestic hot water, and other applications, and is most cost-effective when data center outlet temperatures exceed 55-60 degrees C.
An analysis was made to determine the reduction in payload for a 300 nautical mile orbit resulting from the addition of inert weight, representing recovery gear, to the first-stage booster of a three-stage rocket vehicle. The values of added inert weight investigated ranged from 0 to 18 percent of gross weight at lift off. The study also included the effects on the payload in orbit and the distance from the launch site at burnout and at impact caused by variation in the vertical rise time before the programmed tilt. The vertical rise times investigated ranged from 16-7 to 100 percent of booster burning time. For a vertical rise of 16.7 percent of booster burning time it was found that a 50-percent increase in the weight of the empty booster resulted in only a 10-percent reduction of the payload in orbit. For no added booster weight, increasing vertical rise time from 16-7 to 100 percent of booster burning time (so that the spent booster would impact in the launch area) reduced the payload by 37 percent. Increasing the vertical rise time from 16-7 to 50 percent of booster burning time resulted in about a 15-percent reduction in the impact distance, and for vertical rise times greater than 50-percent the impact distance decreased rapidly.
Mission, landing and recovery operations for the Orion crew module involve reentry into the Earth's atmosphere and the deployment of three Nomex parachutes to slow the descent before landing along the west coast of the United States. Orion may have residual fuel (hydrazine, N2H4) or coolant (ammonia, NH3) on board which are both highly toxic to crew in the event of exposure. These risks were evaluated using a first principles analysis approach through fluid dynamics modeling. Plume calculations were first performed with the ANSYS Fluent computational fluid dynamics code. Data were then extracted at locations relevant to crew safety such as the snorkel fan inlet and the egress hatch. Mixing calculations were performed to quantify exposure concentrations within the crew bay before and during egress and departure. Finally, results included herein were used to inform the Orion post-landing Concept of Operations (ConOps) so that strategies could be formulated to maintain crew safety in the event of the loss of fuel or coolant.
The technical and economic feasibility of fluid bed heat exchangers (FBHX) for thermal energy storage (TES) in waste heat recovery applications is assessed by analysis of two selected conceptual systems, the rotary cement kiln and the electric arc furnace. It is shown that the inclusion of TES in the energy recovery system requires that the difference in off-peak and on-peak energy rates be large enough so that the value of the recovered energy exceeds the value of the stored energy by a wide enough margin to offset parasitic power and thermal losses. Escalation of on-peak energy rates due to fuel shortages could make the FBHX/TES applications economically attractive in the future.
As part of the FDIR (Fault Detection, Isolation, and Recovery) Project for the Constellation Program, a task was designed within the context of the Constellation Program FDIR project called the Legacy Benchmarking Task to document as accurately as possible the FDIR processes and resources that were used by the Space Shuttle ground support equipment (GSE) during the Shuttle flight program. These results served as a comparison with results obtained from the new FDIR capability. The task team assessed Shuttle and EELV (Evolved Expendable Launch Vehicle) historical data for GSE-related launch delays to identify expected benefits and impact. This analysis included a study of complex fault isolation situations that required a lengthy troubleshooting process. Specifically, four elements of that system were considered: LH2 (liquid hydrogen), LO2 (liquid oxygen), hydraulic test, and ground special power.
A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions. The differences in drag can be eliminated for the design Mach number. Experimental results confirm the results of the theoretical analysis and show that pressure recoveries of 95 percent for Mach numbers of 1.33 and 1.52, 92 percent for a Mach number of 1.72, and 86 percent for a Mach number of 2.10 are possible, with the configurations considered. If the mass flow decreases, the total drag coefficient increases gradually and the pressure recovery does not change appreciably. The results of this work were first presented in a classified document issued in 1946.
A supersonic inlet with supersonic deceleration of the flow entirely outside of the inlet is considered. A particular arrangement with fixed geometry having a central body with a circular annular intake is analyzed, and it is shown theoretically that this arrangement gives high pressure recovery for a large range of Mach number and mass flow and therefore is practical for use on supersonic airplanes and missiles. For some Mach numbers the drag coefficient for this type of inlet is larger than the drag coefficient for the type of inlet with supersonic compression entirely inside, but the pressure recovery is larger for all flight conditions. The differences in drag can be eliminated for the design Mach number. Experimental results confirm the results of the theoretical analysis and show that pressure recoveries of 95 percent for Mach numbers of 1.33 and 1.52, 92 percent for a Mach number of 1.72, and 86 percent for a Mach number oof 2.10 are possible with the configurations considered. If the mass flow decreases, the total drag coefficient increases gradually and the pressure recovery does not change appreciably.
The "Hayabusa" re-entry capsule was safely carried into the clean room of Sagamihara Planetary Sample Curation Facility in JAXA on June 18, 2010. After executing computed tomographic (CT) scanning, removal of heat shield, and surface cleaning of sample container, the sample container was enclosed into the clean chamber. After opening the sample container and residual gas sampling in the clean chamber, optical observation, sample recovery, sample separation for initial analysis will be performed. This curation work is continuing for several manths with some selected member of Hayabusa Asteroidal Sample Preliminary Examination Team (HASPET). We report here on the 'Hayabusa' capsule recovery operation, and transportation and acceptance at the curation facility of the Hayabusa re-entry capsule.
As computers become more widely used, and in particular as they become used in more safety critical applications, the reliability of the computer system and its software becomes more important. There is also an increasing need for high levels of reliability in applications involving very large numbers of inexpensive units where recall of the units would be disproportionately expensive. The nature of faults and the assumptions made by different approaches to correct operation are considered. The recovery block approach is described and a probabilistic analysis of its effectiveness, with and without correlated design errors is provided. Mechanisms for generating acceptance tests from specifications, and for providing recovery in the presence of asynchrony, are described. An analysis of, and design for, the provision of recovery blocks in the microprogram of the Bendix BDX930 processor is provided. An example of the use of recovery blocks in a simple operating system is also provided.
A covariance analysis is presented for a differential GPS-based technique for satellite tracking and gravity recovery to be demonstrated on Topex in the early 1990's. The technique employs data from an ensemble of repeat ground tracks to recover a unique satellite epoch state for each track and a set of invariant local gravity parameters common to all tracks. For satellites above about 800 km altitude, where gravity modeling is the dominant systematic error, averaging of random error over many arcs and adjustment of the gravity model reduces the final satellite position error. The local gravity parameters can then be used to produce a refined global gravity model. The analysis indicates that errors ranging from 5 to 8 cm in Topex altitude and 0.05 to 0.2 mgal for the gravity field can be achieved, depending on the number of repeat arcs used.
Ever-increasing turbine scales and their associated logistical challenges have reignited questions about the performance of downwind rotor configurations. A particular potential benefit of downwind rotor configurations is the farm-scale power increase that may be conferred by tilt-driven downward wake entrainment and associated wake recovery. In this work, a comprehensive aerodynamic analysis is carried out to understand the mechanisms for wake entrainment and recovery across a spectrum of velocity and inflow alignment conditions on a small, structured farm in order to understand the impact of downwind rotors on farm production. The results show that the benefits demonstrated previously in the literature for downwind-rotor farms in aligned flows are fragile, and, outside of strong farm/flow alignment conditions, power production benefits for small farms with downwind rotor configurations are significantly if not completely mitigated by misalignment effects. The work indicates that farm-scale benefits for downwind rotors must be realized either from large-scale entrainment benefits, with more exotic farm arrangements that can take advantage of the aerodynamic effects, or from beneficial fatigue impacts from entrainment of less turbulent outer boundary layer flows.