Search NASA⌕ Search

SEARCH · Search NASA

Results for “SEAPLANES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 145 records · Page 8
All sourcesNASA NTRSDOE OSTI
NASA NTRS1953

A Brief Hydrodynamic Investigation of a 1/24-Scale Model of the DR-77 Seaplane

A limited investigation of a 1/24-scale dynamically similar model of the Navy Bureau of Aeronautics DR-77 design was conducted in Langley tank no. 2 to determine the calm-water take-off and the rough-water landing characteristics of the design with particular regard to the take-off resistance and the landing accelerations. During the take-off tests, resistance, trim, and rise were measured and photographs were taken to study spray. During the landing tests, motion-picture records and normal-acceleration records were obtained. A ratio of gross load to maximum resistance of 3.2 was obtained with a 30 deg. dead-rise hydro-ski installation. The maximum normal accelerations obtained with a 30 deg. dead-rise hydro-ski installation were of the order of 8g to log in waves 8 feet high (full scale). A yawing instability that occurred just prior to hydro-ski emergence was improved by adding an afterbody extension, but adding the extension reduced the ratio of gross load to maximum resistance to 2.9.

Fisher, Lloyd J.↗
NASA NTRS1949

Comparison of Water-Load Distributions Obtained during Seaplane Landings with Bureau of Aeronautics Specifications. TED No. NACA 2413

Bureau of Aeronautics Design Specifications SS-IC-2 for water loads in sheltered water are compared with experimental water loads obtained during a full--scale landing investigation. This investigation was conducted with a JRS-1 flying boat which has a 20 degrees dead-rise V-bottom with a partial chine flare. The range of landing conditions included airspeeds between 88 and 126 feet per second, sinking speeds between 1.6 and 9.1 feet per second, flight angles less than 6 degrees, and trims between 2 degrees and 12 degrees. Landings were moderate and were made in calm water. Measurements were obtained of maximum over-all loads, maximum pitching moments, and pressure distributions. Maximum experimental loads include over-all load factors of 2g, moments of 128,000 pound-feet, and maximum local pressures greater than 40 pounds per square inch. Experimental over-all loads are approximately one-half the design values, while local pressures are of the same order as or larger than pressures calculated from specifications for plating, stringer, floor, and frame design. The value of this comparison is limited, to some extent, by the moderate conditions of the test and by the necessary simplifying assumptions used in comparing the specifications with the experimental loads.

Smiley, Robert F.↗
NASA NTRS1934

The calculated effect of trailing-edge flaps on the take-off of flying boats

The results of take-off calculations are given for an application of simple trailing-edge flaps to two hypothetical flying boats, one having medium wing and power loading and consequently considerable excess of thrust over total resistance during the take-off run, the other having high wing and power loading and a very low excess thrust. For these seaplanes the effect of downward flap settings was: (1) to increase the total resistance below the stalling speed, (2) to decrease the get-away speed, (3) to improve the take-off performance of the seaplane having considerable excess thrust, and (4) to hinder the take-off of the seaplane having low excess thrust. It is indicated that flaps would allow a decrease in the high angles of wing setting necessary with most seaplanes, provided that the excess thrust is not too low.

Parkinson, J E↗
NASA NTRS1933

A Complete Tank Test of a Model of Flying-boat Hull - N.A.C.A. Model 16

A model of a 2-step flying-boat hull, of the type generally used in England, was tested according to the complete method described in the N.A.C.A. Technical Note No. 464. The lines of this model were taken from offsets given by Mr. William Munro in Flight, May 29, 1931. The data cover the range of loads, speeds, and trim angles that may be of use in applying the hull form to the design of any seaplane. The results are reduced to nondimensional form to aid application to design problems and facilitate comparison with the performance of other hulls. The water characteristics of Model 16 are compared with those of Model 11-A, which is representative of current American practice. The results show that when the two forms are applied to a given seaplane design under optimum conditions for each, the performance of Model 16 will be somewhat inferior to that of Model 11-A.

Shoemaker, James H↗
NASA NTRS1933

A complete tank test of a model of a flying-boat hull-N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M↗
NASA NTRS1927

Tests on airplane fuselages, floats and hulls

This report is a compilation of test data on airplane fuselages, nacelles, airship cars, seaplane floats, and seaplane hulls, prepared by the Bureau of Aeronautics, at the requests of the National Advisory Committee for Aeronautics. The discussion of the data includes the derivation of a scale correction curve to be used in obtaining the full scale drag. Composite curves of drag and L/D for floats and hulls are also given. (author)

Diehl, Walter S↗
NASA NTRS1952

Hydrodynamic Impact of a System with a Single Elastic Mode II : Comparison of Experimental Force and Response with Theory

Hydrodynamic impact tests were made on an elastic model approximating a two-mass spring system to determine experimentally the effects of structural flexibility on the hydrodynamic loads encountered during seaplane landing impacts and to correlate the results with theory. A flexible seaplane was represented by a two-mass spring system consisting of a rigid prismatic float connected to a rigid upper mass by an elastic structure. The model had a ratio of sprung mass to hull mass of 0.6 and a natural frequency of 3.0 cycles per second. The tests were conducted in smooth water at fixed trims and included both high and low flight-path angles and a range of velocity. Theoretical and experimental comparisons indicated that the theoretical results agreed well with the experimental results.

Miller, Robert W↗
NASA NTRS1933

A Complete Tank Test of a Model of a Flying-Boat Hull - N.A.C.A. Model No.11

This note discusses the limitations of the conventional tank test of a seaplane model. The advantages of a complete test, giving the characteristics of the model at all speeds, loads, and trim angles in the useful range are pointed out. The data on N.A.C.A. Model No.11, obtained from a complete test, are presented and discussed. The results are analyzed to determine the best trim angle for each speed and load. The data for the best angles are reduced to non-dimensional form for ease of comparison and application. A practical problem using the characteristics of model no.11 is presented to show the method of calculating the take-off time and run of a seaplane from these data.

Shoemaker, James M.↗
NASA NTRS1950

Hydrodynamic Properties of Planing Surfaces and Flying Boats

The study of the hydrodynamic properties of planing bottom of flying boats and seaplane floats is at the present time based exclusively on the curves of towing tests conducted in tanks. In order to provide a rational basis for the test procedure in tanks and practical design data, a theoretical study must be made of the flow at the step and relations derived that show not only qualitatively but quantitatively the inter-relations of the various factors involved. The general solution of the problem of the development of hydrodynamic forces during the motion of the seaplane float or flying boat is very difficult for it is necessary to give a three-dimensional solution, which does not always permit reducing the analysis to the form of workable computation formulas. On the other had, the problem is complicated by the fact that the object of the analysis is concerned with two fluid mediums, namely, air and water, which have a surface of density discontinuity between them. The theoretical and experimental investigations on the hydrodynamics of a ship cannot be completely carried over to the design of floats and flying-boat hulls, because of the difference in the shape of the contour lines of the bodies, and, because of the entirely different flow conditions from the hydrodynamic viewpoint.

Sokolov, N. A.↗
NASA NTRS1949

Systematic model researches on the stability limits of the DVL series of float designs

To determine the trim range in which a seaplane can take off without porpoising, stability tests were made of a Plexiglas model, composed of float, wing, and tailplane, which corresponded to a full-size research airplane. The model and full-size stability limits are in good agreement. After all structural parts pertaining to the air frame were removed gradually, the aerodynamic forces replaced by weight forces, and the moment of inertia and position of the center of gravity changed, no marked change of limits of the stable zone was noticeable. The latter, therefore, is for practical purposes affected only by hydrodynamic phenomena. The stability limits of the DVL family of floats were determined by a systematic investigation independent of any particular sea-plane design, thus a seaplane may be designed to give a run free from porpoising.

Sottorf, W.↗
NASA NTRS1927

The "Dornier Mercury" commercial airplane with B.M.W. VI 600 HP. engine

The Dornier Mercury (Merkur) is an outgrowth of the Dornier Komet. It is designed as a passenger aircraft with the Alpine routes in mind. Its fuselage is made of steel for high stressed parts and duraluminum for all others. It can also be outfitted as a seaplane.

AIRPLANES - DORNIER MERKUR (GER )↗
NASA NTRS1945

An Investigation of the Ranger V-770-8 Engine Installation for the Edo XOSE-1 Airplane II : Aerodynamics

Investigations were made to determine the cowling and cooling characteristics of the Ranger V-770-8 engine installation in an observation seaplane. Final cowl configurations possessed ample engine and oil-cooler pressure drops for cooling in the critical normal-power climb condition with any of the three baffle configurations tested. The indicated critical Mach number of the cowling was found to be 0.70 as determined by the pressure on the lower lip of the inlet.

ENGINE COWLINGS-RANGER↗
NASA NTRS1922

Comparative performance with direct and geared engines

Comprehensive tests were made to compare the performance of the F-5-L Boat Seaplane fitted with direct drive and Liberty engines. Details are given on the test conditions. The conclusions of the comparison tests follow. 1) An F-5-L with geared engines takes off in approximately 90 percent of the time required for the same airplane with standard direct drive engines. An F-5-L with geared engines climbs in 20 minutes to an altitude approximately 20 percent greater than that obtained with the standard direct drive on the same airplane. 3) There is a large difference between the climbs of the two airplanes of the same type. This difference will always be more pronounced when the climb is normally slow. In the case of the F-5-L airplanes under construction, it is of the order of a 10 percent difference in altitude on a 20 minute climb. 4) The maximum speed of an F-5-L with geared engines is about 3.5 percent greater than the maximum speed of the same airplane with standard direct drive engines (at the same engine r.p.m.). 5) The fuel consumption is probably less effected by the type of drive than by inherent differences in the performance of different airplanes.

Diehl, W S↗
NASA NTRS1928

The reaction on a float bottom when making contact with water at high speeds

Tests were conducted to investigate the possibility of a serious accident arising from unintentional contact with the water in substantially horizontal flight at high speed. Referring to vector diagrams on Figure 2, it will be seen that a very dangerous condition may arise if the float be allowed to come in contact with the water at high speeds as, for example, when flying at high speed just above the water. The initial diving moment due to suction and drag combined may be great enough to cause the seaplane to nose under before the pilot is able to control the motion. The same test data indicate clearly the existence of forces and moments tending to produce the phenomenon observed by Mr. Carroll (Technical Note No. 287) when the maneuver is carried out at lower speeds, as in a landing.

Richardson, H C↗
NASA NTRS1934

Tank tests of flat and v-bottom planning surfaces

Four planing surfaces, all having beams of 16 inches and lengths of 60 inches but varying in dead rise by 10 degrees increments from 0 degrees to 30 degrees, were tested in the N.A.C.A. tank. The results cover a wide range of speed, loads, and trim angles, and are applicable to a variety of problems encountered in the design of seaplanes. The data are analyzed to determine the characteristics of each surface at the trim angle giving minimum resistance for all the speed and loads tested. A planing coefficient intended to facilitate the application of the results to design work is developed and curves of resistance, wetted length, and center of pressure are plotted against this coefficient. Several examples, showing the application of the test data to specific design problems are included.

Shoemaker, James M↗